Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Sikagard 75 EpoCem
Construction
Construction
Uses
Advantages
Solvent-free
Product Data
Form/Colour
Component A
: Liquid / Whitish
: 1.14 kg pail
Storage
Shelf life
Sikagard 75 EpoCem
4/4
Sikagard 75 EpoCem
1/4
Technical Data
Density
Component A
Mixing
Shake well component A and B. Then pour component A (white liquid) into
component B (plastic canister) and shake vigorously for 30 seconds.
Pour the binder mixture (A+B) into a 30-litre pail and add component C.
Mix thoroughly for minimum 2 minutes, using a suitable low-speed electric stirrer (500 rpm.) or a forced action (pan type) mixer.
Application
: ~ 1.06 kg/ltr
Consumption
Protect the freshly applied Sikagard 75 Epocem from rains for 24 hours.
2
Rate of reaction
Cleaning
Uncured material can be removed from tools with water. Once cured,
Sikagard 75 Epocem can only be removed mechanically.
Curing
Notes on application/Limits
10 C
Pot life
45 minutes
20 C
30 C
35 minutes 25 minutes
Curing time:
Compressive strength
1 day
18 hours
12 hours
3 days
2 days
1 day
Fully cured
14 days
7 days
5 days
15 N/mm (1 day)
Ecology
Transportation class
Non hazardous
Bond strength
Waste disposal
Maximum 2 mm
Important Notes
Disclaimer
The information, and, in particular, the recommendations relating to the application and end-use
of Sika products, are given in good faith based on Sikas current knowledge and experience of
the products when properly stored, handled and applied under normal conditions in accordance
with Sikas recommendations. In practice, the differences in materials, substrates and actual site
conditions are such that no warranty in respect of merchantability or of fitness for a particular
purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either
from this information, or from any written recommendations, or from any other advice offered. The
user of the product must test the products suitability for the intended application and purpose.
Sika reserves the right to change the properties of its products. The proprietary rights of third
parties must be observed. All orders are accepted subject to our current terms of sale and
delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the
product concerned, copies of which will be supplied on request.
application
Substrate temperature
Minimum + 8 C
o
Maximum + 30 C
Application
Surface preparation
Surfaces must be sound and clean and free from all traces of loose
material, laitance, oil and grease. Pre-wetting is not necessary except in
the case of highly absorbent backgrounds and/ or exposure to intense
sunlight.
In case of pre-wetting, no standing water on the surface is allowed.
Sikagard 75 EpoCem
2/4
Sikagard 75 EpoCem
3/4
Technical Data
Density
Component A
Mixing
Shake well component A and B. Then pour component A (white liquid) into
component B (plastic canister) and shake vigorously for 30 seconds.
Pour the binder mixture (A+B) into a 30-litre pail and add component C.
Mix thoroughly for minimum 2 minutes, using a suitable low-speed electric stirrer (500 rpm.) or a forced action (pan type) mixer.
Application
: ~ 1.06 kg/ltr
Consumption
Protect the freshly applied Sikagard 75 Epocem from rains for 24 hours.
2
Rate of reaction
Cleaning
Uncured material can be removed from tools with water. Once cured,
Sikagard 75 Epocem can only be removed mechanically.
Curing
Notes on application/Limits
10 C
Pot life
45 minutes
20 C
30 C
35 minutes 25 minutes
Curing time:
Compressive strength
1 day
18 hours
12 hours
3 days
2 days
1 day
Fully cured
14 days
7 days
5 days
15 N/mm (1 day)
Ecology
Transportation class
Non hazardous
Bond strength
Waste disposal
Maximum 2 mm
Important Notes
Disclaimer
The information, and, in particular, the recommendations relating to the application and end-use
of Sika products, are given in good faith based on Sikas current knowledge and experience of
the products when properly stored, handled and applied under normal conditions in accordance
with Sikas recommendations. In practice, the differences in materials, substrates and actual site
conditions are such that no warranty in respect of merchantability or of fitness for a particular
purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either
from this information, or from any written recommendations, or from any other advice offered. The
user of the product must test the products suitability for the intended application and purpose.
Sika reserves the right to change the properties of its products. The proprietary rights of third
parties must be observed. All orders are accepted subject to our current terms of sale and
delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the
product concerned, copies of which will be supplied on request.
application
Substrate temperature
Minimum + 8 C
o
Maximum + 30 C
Application
Surface preparation
Surfaces must be sound and clean and free from all traces of loose
material, laitance, oil and grease. Pre-wetting is not necessary except in
the case of highly absorbent backgrounds and/ or exposure to intense
sunlight.
In case of pre-wetting, no standing water on the surface is allowed.
Sikagard 75 EpoCem
2/4
Sikagard 75 EpoCem
3/4
Sikagard 75 EpoCem
Construction
Construction
Uses
Advantages
Solvent-free
Product Data
Form/Colour
Component A
: Liquid / Whitish
: 1.14 kg pail
Storage
Shelf life
Sikagard 75 EpoCem
4/4
Sikagard 75 EpoCem
1/4