Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
76
80
81
82
83
84
85
86
87
88
85
71
88
75
73
74
Version 3
Valid as of Software V2.0
Status area
72
86
87
79
ESC key
ENTER key
START key
Start LED
STOP key
+ key
key
Settings key
Cursor key right
80
83
77
78
81
82
604287/0311/e
Error messages
Version 3
Valid as of Software V2.0
Program structure
Program
Description
8 to 20
Individual Programs
ERR
No.
Entry
T<B
Entry
L>T
Entry
Enter a logical value for the vacuum-on temperature Vx1 or the vacuum-off temperature Vx2
Entry
V2x > Tx + 1C
10
Entry
11
System
13
*, **
Excess temperature! Program aborted, furnace head opens to allow the furnace to cool down.
Parameter
Value range
Program number P
120
Stand-by temperature
100700 C
00:1830:00
Check the heater fuse. If the fuse is O.K., contact your local Ivoclar Vivadent Service Center.
Entry
T2 < T1
16
System
17
A firing program in progress was interrupted for more than 10 s. The program cannot be continued!
10
Entry
T1 > V12
18
11
Entry
vV set, but V2 is
missing or invalid
19
12
System
20
**
13
System
23
8
9
no
Please observe the notes in the Instructions for Use of the corresponding material.
(*)
Value range
2121292 F
30140 C/min
54252 F/min
Holding temperature
1001200 C
2122192 F
The heating muffle is very old. It is recommended to replace it. After the error message has been
acknowledged, a firing program may still be started.
00.0160:00
14
System
24
V1
Vacuum on
0 or 11200 C
0 or 342192 F
16
Entry
26
V2
Vacuum off
0 or 11200 C
0 or 342192 F
30140 C/min
54252 F/min
1001200 C
2122192 F
17
System
27
**, ***
The furnace head cannot be moved to the final position. It might be blocked by an external mechanical
source! If this is not the case, please contact your local Ivoclar Vivadent Service Center!
18
System
28
**
The furnace head does not open/close correctly. The furnace head was manually moved or is obstructed.
The furnace head must only be moved using the keys intended for this purpose!
21
System
The vacuum cannot be established. Check the seal of the firing chamber, vacuum hose, vacuum pump,
pump fuse.
33
Entry
HV > H (H2)
110
35
Entry
120
38
System
(*)
t2
Second stage
Holding temperature
Second stage
Holding time
Second stage (min : sec)
V1 (V1 2)
Second stage
A firing program in progress was interrupted by a brief power failure. The program is continued!
45
System
Vacuum drop
801
46
System
802
No vacuum increase could be measured. Check the following points: Is the firing chamber tight (no
contamination on the sealing surfaces)? Is the vacuum hose connected? Is the vacuum pump connected?
Is the fuse F1 o.k.?
ATK2 calibration:
Pre-heating to 963 C
1302
**
75
System
Error during calibration. Sample may not be correctly inserted. Try again with a new sample and make sure the
sample makes ampl contact.
79
Note
Calibration reminder
1310
Some time has passed since the last calibration procedure. Calibrate the furnace soon.
80
Note
Dehumidification reminder
1312
Some time has passed since the last dehumidification procedure. Dehumidificat the furnace soon.
Please contact the Ivoclar Vivadent After Sales Service, if other error messages being displayed.
V2 (V2 2)
00.0160:00
Vacuum on
0 or 11200 C
0 or 342192 F
Vacuum off
Second stage
0 or 11200 C
0 or 342192 F
Long-term cooling
0 or 501200 C
0 or 1222192 F
tL
0 or 150
0 or 3290