Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Table of Contents
Forewords..2
Safety warning3
. Functions and Purposes.4
. Technical parameters.5
. Impulse main engine installation6
. Lectotype of the front-end fence..13
. Installation of the front-end fence15
. Application and maintenance...20
Appendix: G5 main engine packing list.21
Page 1 of 23
Forewords
Page 1 of 23
Safety cautions
Never install the fence during thunder and lightning.
Never install the impulse main engine directly in damp area.
Never touch the electrical conductor unless the fence has been relieved from high pressure.
Before installation and application of the product, the workers shall be educated with technical
training and safety training.
This work has an AC220V (50Hz) voltage when working; the output terminal and the front-end
has 5000V~10000V impulse high pressure; please never touch it to ensure personal and
equipment safety.
The operators of this product must have electrical apparatus safety and electrical shock rescue
knowledge; you should read the instruction book before installation and application to be familiar
with the accurate application methods and specifications of the product; otherwise, the users shall
be responsible for any results.
Once there is abnormal situation, the power supply shall be cut off at first, and then professional
operators for installation and inspection shall be informed immediately.
Before using this product, please learn all the contents in this manual.
Page 1 of 23
The front-end fence with high pressure electricity will bring great deterrence and much
obstruction at the same time to the invaders, which greatly increase the cost for jumping
over the fence.
1.2
The front-end fence is physical fence, which wont be restricted by the wind and
complication of the topography, and there are no blind areas and dead corners, thus it can be
erected followed by the terrain without any careless omission.
1.3
The impulse main engine is equipped with warning interface, which can be interlocked with
other security protection equipments and can be designed and installed according to the
users requirements, on-site geographical environment and safety class to increase the
security protection class of the system.
1.4
Distinguishing functionthe fence can inspect various intrusion grade by intelligence. The
intelligent distinguishing is between animal obstruction or human invasion; occasional
obstruction or force obstruction; the misstatement rate is extremely low.
1.5
It can work constantly for 24 hours, and the system can be equipped with 7AH storage
battery to ensure constant work in case of power cut; defense deployment/removing can be
done at any time based on different situations.
1.6
Apply high and low pressure impulse of low frequency and low energy (high pressure
5000V~10000V and low pressure 500V~1000V). Because the energy is extremely low and
the reaction duration is temporary, no damage will be done to the human body. In case it is
touched, people will leave since there is direct electric shock.
1.7
It has good safety capacity, G5 can satisfy national fence standard GB/T 7946-2008. The
system can be installed at any place where security protection is required.
Page 1 of 23
. Technical parameters
M
odel
Parameter
Defense
area type
High and
low
pressure
type
Keyboard
s
connect
ion
Software
connectio
n
Outside
dimension
s
Power
supply
Applied
environm
ent
Alarming
delay
Rated
output
Impulse
characteri
stic
G5101
G5102
G5171
G5201
G5202
G5271
G5106
G5176
G5206
G5276
Single
defense
Four-w
ire
Single
defens
e
Four-w
ire
High
pressur
e
Single
defense
Four-w
ire
Double
defense
Four-w
ire
Double
defense
Four-w
ire
Single
defense
c
Single
defense
Six-wir
e
Double
defense
Six-wir
e
Double
defense
Six-wir
e
High
and
low
pressur
e
convert
ing
High
and
low
pressur
e
convert
ing
Double
defens
e
Four-w
ire
High
pressur
e
High
and
low
pressur
e
convert
ing
High
and
low
pressur
e
convert
ing
High
and
low
pressur
e
convert
ing
High
and
low
pressur
e
convert
ing
High
and
low
pressur
e
convert
ing
High
and
low
pressur
e
convert
ing
32 cm22 cm11.7cm
AC220V(10%) 50Hz;
AC24V
>30W;
DC12V
>30W
1s
30W
Impulse extent: high pressure 5000V~10000V, low pressure 500V~1000V (for detailed impulse
status, please refer to high and low pressure type)
Impulse frequency: once per second for the signal, and the pulse duration ratio 1/10
Insulated
resistance
Impulse duration: 0.1s Maximum currency for each impulse:2.5mc Maximum energy: 5.0J
Peak value for the impulse current: 10A
Duration of more than 300mA output: 1.5ms
The insulating resistance between power supply socket and the outside exposed metal parts shall be
more than 100M.
Page 1 of 23
Page 1 of 23
Power light
System indicator light
Fence warning light
Fault warning light
High pressure indicator light
Low pressure indicator light
Start switch
High pressure transferring switch
Drawing 3-1 G5101/G5106 impulse main engine plate graphic representation
Page 1 of 23
Power light
System indicator light
Fence warning light
Fault warning light
High pressure indicator light
Low pressure indicator light
Start switch
High pressure transferring switch
Drawing 3-2 G5201/G5206 impulse main engine plate graphic representation
Page 1 of 23
Shutdown
Starting-up
Circuit
interruption
/short circuit
Power
(power
indicator)
Ok
(system
indicator)
Fence
(fence
alarm
light)
Fence
( fence
alarm
light )
Energizer
(fault
alarm light
High
(high
pressure
indicator)
Low
(high
pressure
indicator)
Green
light
works
Red light
off
Red light
off
Red light
off
Red light
off
Red light
off
Red light
off
Green
light
works
Red light
works
Red light
off
Red light
off
Red light
off
Green
light
works
Red light
works
Red light
works
after once
sparkling
Red light
works
after once
sparkling
Red light
off
High
pressure
model
works
High
pressure
model
works
Low
pressure
model
works
Low
pressure
model
works
Green
Red light Red light
Red light
Red light
Red light
Red light
light
works
off
off
works
off
off
works
Note: 220v power fail is the power supply status of the storage battery for main engine use (single defense
area and six-wire have no Fence item)
Low pressure
transferring switch
Model
G5101
System switch
High pressure
transferring switch
G5102
G5171
G5201
G5202
G5271
G5106
G5176
G5206
G5276
Page 1 of 23
Normal close
Normal open
Public
Ground
Main engine fault output
Alarming output
Positive
Negative
Connection sketch
Drawing 3-3 G5 series impulse main engine wire connection cover sketch (the left side is double-defense area,
Page 1 of 23
Illustration
Hole position
Illustration
Earth
RS485_A
RS485_A
Normal
open 1
RS485_B
RS485_B
Normal
close 2
Earth
Input2
Normal
open 2
Input1
Normal
close
DC12V_negative
DC12V_positive
AC24V
Normal
close 1
Public 1
Public 2
Public
Fence
Fence
Normal
open
Earth
Hole
position
AC24V
Illustration
Hole position
Illustration
Earth
RS485_A
RS485_A
RS485_B
RS485_B
Earth
Input2
Input1
DC12V_negative
DC12V_positive
AC24V
Normal
close 1
Public 1
Fence
Normal
open 1
Normal
close
Public
Normal
open
Earth
AC24V
Page 1 of 23
Table 3-3 G5 series impulse main engine wire connection cover hole position
3.1.4 Main engine and front-end wire connection
The wire connection principle of impulse main engine front-end fence is like drawings 3-4,
3-5, 3-6 and 3-7.
Lightning arrestor
Grounding
Drawing 3-4 G5101\G5102\G5171 model impulse main engine wire connection
Page 1 of 23
Lightning arrestor
Grounding
Drawing 3-5 G5106\G5176 model impulse main engine wire connection
Page 1 of 23
Lightning arrestor
Grounding
Drawing 3-6 G5201\G5202\G5271 model impulse main engine wire connection
Lightning arrestor
Grounding
Drawing 3-7 G5206\G5276 model impulse main engine wire connection
3.2
guardhouse or close to local public security authority. The normal used are four-wire to
twelve-wire system.
High level safety; the length for each defense area shall be less than 100m, and there are
many defense areas in the fence. Each defense area must be equipped with independent
main controller with independent alarming device which can indicate the alarming position.
Normally, the warning output shall be interlocked with CCTV, red infrared correlation, spot
light, alarming device and other safety protection systems. The normal used are four-wire to
twelve-wire system.
4.2
Fence types
According to on-site installation type, the fence can be divided into wall top, subordination
and independent models. In case special installation is required, you can contact the local
dealer or Shanghai Gato Information Technology Co., Ltd.
the working parts of independent fence wont be touched by people and be placed in closed
area.
. Installation of the front-end fence
5.1
5.1.1 Its forbidden to install alternating current on the fence. When the product is out of service or
in a error, the fence wont have alternating current.
5.1.2 This product can satisfy international safety standard, and when there is alarm situation, the
impulse generator will close automatically; thus nobody will be injured.
5.1.3 The electric impulse wont damage the invaders, however, in order to remind and alert the
invaders, first of all, on marked place of the fence, there must be at least one warning sign
saying electric fence, no climbing every 10m; secondly, the touchable installed height of
the fence shall be more than 1.8m; in case its not high enough, the outside and both sides of
the fence shall be installed with divider wall or network to avoid personal touch
accidentally.
5.1.4 The fence has impulse height; when there is accidental touch, or a certain object is close to the
energized conductor, there will be slight electric spark. Therefore, the fence shall be erected
at places where there is no inflammable gas or liquid; or to keep a certain distance according
to relevant international and national standards; or protective safety separation measures
shall be taken.
5.1.5 The fence cannot be erected at the same electric pole with power circuit or telecommunication
line.
5.1.6 The horizontal distance between the fence and public road shall be more than 5m (except top
wall fence).
5.1.7 The fence shall be kept enough distance with electric line. See table 5-1 for the minimum
distance:
Ariel multi-conductor power
lines
Below 10
35~110
220
330
500
Table 5-1 The minimum distance between fence and Ariel multi-conductor power lines
5.2
When install vertically the fence, the sequential direction for universal base shall be
identical to keep beauty. For leaning installation, the sector of universal base shall face the
scheduled leaning direction of fence, and the workable space for the front fence shall be
ensured. The scheduled mast position shall be installed with single universal base, and the
scheduled loading rod and end pole position shall be installed with double universal base.
In addition, special attention shall be paid to the fact the direction of universal base at the
corner of the wall shall be identical with leaning direction of the rod during construction.
See the following drawing:
5.3.1 When underground wiring is needed for the fence, high pressure insulating conductor line
with rated pressure which is more than 15KV shall be applied to go through insulating duct
assembly. The lead with positive pole and negative pole shall be penetrated into different
insulating pipes.
5.3.2 There must be enough room between insulating lines and insulating lines, and insulating lines
and metal electrical conductor. According to GB16796-1997 installation requirements and
test methods for safety precaution alarming equipments, the clearance of high pressure live
parts of this product shall be more than 43mm, and the creepage distance shall be more than
50mm.
5.3.3 Normally, there are two ways of connection between insulating lines: winding by itself and the
concealed hinge must be securely tightened with at least five circles; using line connector,
penetrate the lead heads into connector and then compress the lead securely into the
connector using clamp.
5.3.4 In order to protect plant from climbing onto the fence, the minimum distance between fence
and the plants shall be 200mm, and the calculation shall be based on the plants under
waving condition.
Page 1 of 23
5.3.5 One side or both sides of the independent fence that erected on the flat ground shall be
installed with protective screening or enclosure. Its height shall be more than 1.2m, and the
distance of the bottom lead with the ground shall be 150mm, and the distance between fence
and protective network or the enclosure shall be more than 1m.
5.4
Lightning arrestor
Grounding
Drawing 5-4 Eight-channel connection methods
Defense deployment and withdrawal must be managed and kept in good records by
professional personnel; other personnel are not allowed to do any treatment at their disposal.
In case defense withdrawal is required because of maintenance or other reasons, there must
be instructions from the person in charge and the records shall also be kept. After defense
withdrawal, bulletin board (under inspection) must be indicated to avoid anybody who
doesnt understand the situation and close the current (set up defenses); only after receiving
the defense setting up instruction, can the current be closed.
Three-core connector shall be applied before energizing of the main engine, and then
connect the power cord; this sequence must be followed.
Check the displaying lamp everyday, check whether the power supply source is stable.
Keep well the maintenance work of main engine and front-end for monthly power cut. i.e,
the cleaning of main engine and the clearance of front-end and then keep the records.
Special attention shall be paid to the disadvantages that the growth of trees and grass may
bring; it should be kept with a reasonable distance between the trees, grass and the fence to
avoid any error report because of short circuit or circuit interruption under windy weather.
The essential factors that decide whether the system can work normally is daily
maintenance, which is also the main factor to keep its service life.
(The contents can be printed and pasted onto the gatekeepers room or control center room
based on real situation)
Page 1 of 23
Item
Description
Quantity
1 set
1 copy
External diagram
Remarks
Please
keep
properly
3
Guarantee card
1 piece
Please
properly
Power cord
Power cord
1 piece
3x1.0 mm2
3x1.0 mm2
1
piece
Page 1 of 23
keep