Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
www.andhracolleges.com
Answer any FIVE Questions
All Questions carry equal marks
�����
3. Interface a 4 x 4 key board with 8086 using 8255 and write an ALP for detecting
the key closure and return the key code in AL. The debouncing period for a key is
10 ms.Use software key debouncing technique. DEBOUNCE is an available 1 ms
delay routine. [16]
4. �a) Explain the cascaded mode operation of 8259 with a neat block diagram
�b) write about operational command words of 8259. [10+6]
5. �a) Write an 8086 instruction sequence for transmitting 50 characters which are
stored from the location 2010H using 8251.
�b) Write an 8086 instruction sequence for receiving 50 characters using 8251 and
store them in memory at location 2080H. [8+8]
www.andhracolleges.com
6. �a) Interface 8255 I/O ports with 8051 and the address of port A should be 0000H
�b) Explain about the three general errors in asynchronous serial transmission.
to serial interrupt?
�b) Discuss the internal and external interrupts in 8051?
[10+6]
7. �a) Give the priority of the interrupts in 8051? How we can give highest priority
8. �a) Draw the pin diagram of 74LS573 latch and write 8051 program to output the
data on port P1. Use P3.0 for latch pin.
[8+8]
�b) Explain the interfacing of the external program memory to 8051 using 74LS573
latch with a neat diagram and draw the waveforms. [8+8]
�����
www.andhracolleges.com
Answer any FIVE Questions
All Questions carry equal marks
�����
1. �a) Discuss about the interface signals of the 8086 processor in maximum mode?
�b) Draw the block diagram of 8288 bus controller and explain it? [8+8]
2. �a) Write an 8086 Assembler Program that adds two given 4-digit BCD numbers
�b) How do you pass parameters to a MACRO? [12+4]
3. Design a stepper motor controller and write an ALP to rotate shaft of a 4-phase
stepper motor with 200 rotor teeth, for rotations through an angle of 135� in 2
seconds. [16]
www.andhracolleges.com
6. �a) Draw the architectural diagram of 8051 microcontroller and explain in detail
about each block.
�b) Explain the basic differences between a microprocessor and a microcontroller.
[10+6]
7. �a) Write 8051 program to generate 2 kHz square waves on pin P1.0 of port 1
using Timer interrupt.
�b) Write 8051 program to receive a serial byte through RxD. [8+8]
8. �a) Give the pin diagram of CD4511 7-segment display and explain how you can
interface to 8051 microcontroller with a diagram.
�b) Write an 8051 subroutine to control the 7-segment display operation. [8+8]
�����
www.andhracolleges.com
Answer any FIVE Questions
All Questions carry equal marks
�����
1. �a) Discuss about the interface signals of the 8086 processor in maximum mode
�b) Discuss SBB, AAD, TEST, SCAS instructions of 8086. [8+8]
2. Write an 8086 Assembler program to decide the parity of a given number? If the
parity is even, set DL to 00H, else set DL to 01H. The given number may be a
multibyte number with a maximum length of 8 bytes. [16]
5. �a) Discuss the serial data transmission standards and their specifications.
www.andhracolleges.com
�b) Draw the block diagram of 8251 and explain about each block. [6+10]
6. �a) Draw the architectural diagram of 8051 microcontroller and explain in detail
about each block.
�b) Explain the basic differences between a microprocessor and a microcontroller.
[10+6]
8. �a) Give the pin diagram of CD4511 7-segment display and explain how you can
interface to 8051 microcontroller with a diagram.
�b) Write an 8051 subroutine to control the 7-segment display operation. [8+8]
�����
www.andhracolleges.com
Answer any FIVE Questions
All Questions carry equal marks
�����
3. Explain the Programmed I/O and interrupt driven I/O in detail. [16]
4. �a) Explain the cascaded mode operation of 8259 with a neat block diagram
�b) write about operational command words of 8259. [10+6]
5. �a) Write an 8086 instruction sequence for transmitting the characters using 8251
on a polled basis.
�b) Write an 8086 instruction sequence for receiving 100 characters using 8251 on
www.andhracolleges.com
a polled basis and store them in memory at location 2050H. [8+8]
6. �a) Copy the byte in TCON �88h) to register R1 using at least four different
methods.
�b) Discuss about the internal and external memory handling capabilities of 8051.
[8+8]
7. �a) Give the format of PCON register in 8051 and explain each bit.
�b) Explain mode-1 baud rates and serial data mode-2 multiprocessor mode.[8+8]
8. �a) Draw the pin diagram of 74LS573 latch and write 8051 program to output the
data on port P1. Use P3.0 for latch pin.
�b) Explain the interfacing of the external program memory to 8051 using 74LS573
latch with a neat diagram and draw the waveforms. [8+8]
�����