Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
GSM:..........................................................................................................................................2
To turn on the power for ALD................................................................................................2
To check the receiving power.................................................................................................2
Scan ALD...............................................................................................................................2
TMA.......................................................................................................................................3
ADD TMA.........................................................................................................................3
TMA status.........................................................................................................................3
Set Attenuation...................................................................................................................3
RET........................................................................................................................................3
ADD RET...........................................................................................................................3
Set Tilt................................................................................................................................4
RET status..........................................................................................................................4
Loading RET configuration file.........................................................................................4
Load the file from M2000 to BSC OMU.......................................................................5
Load from BSC OMU to BTS RET...............................................................................5
Calibrate RET:....................................................................................................................5
ALD configuration
GSM:
To turn on the power for ALD
SET
BTSRXUBP:IDTYPE=BYNAME,BTSNAME="XXXBS1",RXUIDTYPE=RXUNAME,RXUNA
ME = "0-40",RXUTYPE=MRFU,PWRSWITCHA=ON,CHKMODA=TMA12DB_ONLY_NON_AISG;
For setting ALD current threshold CHKMODA, refer the following table
Threshold type
TMA12DB_ONLY_NON_AISG
RET_ONLY_COAXIAL
TMA12DB_AISG
ALD
device
TMA only
RET only
TMA & RET
Scan ALD
STR BTSALDSCAN:IDTYPE=BYID,BTSID=10;
To scan particular RF unit, please give additional info in the command.
TMA
ADD TMA
ADD
BTSTMA:IDTYPE=BYID,BTSID=10,DEVICENO=0,DEVICENAME="XXX1G_TMA0",PW
RSUPPLYTYPE=SINGLE_PORT_POWER,CTRLPORTCN=0,CTRLPORTSRN=4,CTRLPOR
TSN=0,SUBUNITNUM=2,VENDORCODE="HW",SERIALNO="1234";
TMA status
To check the status of TMA
DSP BTSTMASUBUNIT:IDTYPE=BYID,BTSID=526;
Set Attenuation
While displaying the status of the TMA, we learn the gain of the TMA.
Actual Gain(0.25db) = 48
= 48*0.25 => 12 db
For a 12db TMA, the attenuation should be between 8 db to 10 db.
Default is 8 db.
SET BTSRXUBP:IDTYPE=BYID,BTSID=10,RXUIDTYPE=RXUNAME,RXUNAME="0-40",RXUTYPE=MRFU,HAVETT1=YES,MRRUATTENFACTOR1=8,HAVETT2=YES,MRRU
ATTENFACTOR2=8;
For Single Feeder[1TX + 2RX] => HAVETT1 & MRRUATTENFACTOR1 is mandatory and
HAVETT2 & MRRUATTENFACTOR2 is optional.
RET
ADD RET
ADD
BTSRET:IDTYPE=BYID,BTSID=10,DEVICENO=0,DEVICENAME="91XXX1G_
RET",CTRLPORTCN=0,CTRLPORTSRN=4,CTRLPORTSN=0,CTRLPORTNO=0,
RETTYPE=SINGLE_RET,SCENARIO=DAISY_CHAIN, VENDORCODE="HW",SE
RIALNO="1234";
RET Naming
ConventionNam
e Suffix
r
rr
y
yyR
yL
rr
Ban
d
800
900
210
0
210
0
180
0
900
Layer
Naming convention
J Layer
T Layer
00NAT1J_RET,00NAT2J_RET,00NAT3J_RET
00NAT1T_RET,00NAT2T_RET,00NAT3T_RET
U layer
00NAT1U_RET,00NAT2U_RET,00NAT3U_RET
U layer
00NAT1U_RET,00NAT2U_RET,00NAT3U_RET
K Layer
00NAT1K_RET,00NAT2K_RET,00NAT3K_RET
G900
00NAT1G_RET,00NAT2G_RET,00NAT3G_RET
Set Tilt
MOD
BTSRETTILT:IDTYPE=BYID,BTSID=1,OPMODE=DEVICENO,DEVICENO=0,TI
LT=100;
RET status
DSP BTSRETSUBUNIT:IDTYPE=BYID,BTSID=XXX;
Calibrate RET:
In few cases, alarm RET antenna not calibrated will occur.
Execute the following command to calibrate RET.
CLB BTSRET:IDTYPE=BYID,BTSID=10,DEVICENO=0,SUBUNITNO=1;