Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Projects
Help
Contacts
Building:
Program:
Building Instructions
Note: This is an expert-level project. If you are new to building with the NXT kit, or
new to the nxtprograms.com web site, you might want to try some of the easier
projects first.
1-23
Start by building the Car with Game Controller project (using the Castor Bot). Click the picture for building
instructions.
24
This project needs the NXT brick pointing the opposite way from the Castor Bot project, so in this step you
need to remove the NXT brick, turn it around, then re-attach it. To do this:
http://www.nxtprograms.com/claw_car/steps.html
1/29
7/17/2016
1. Remove the two motor wires, and detach the two sensor wires from the NXT brick.
2. Carefully remove the NXT brick from the chassis of the Castor Bot. It is attached by two straight white
beams and two angled gray beams on the sides, and four pegs on the bottom. You can either remove
the side beams, or carefully pop them out of the NXT brick and bend them slightly outwards to get the
NXT out.
3. Make sure that the all the black pegs end up on the beams of the chassis and none on the NXT brick.
If they stick to the NXT, take them out and put them back on the chassis beams.
http://www.nxtprograms.com/claw_car/steps.html
2/29
7/17/2016
3. Re-attach the NXT brick in the opposite direction. Get the four bottom pegs plugged in first, then
attach the four side beams.
25
http://www.nxtprograms.com/claw_car/steps.html
3/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
4/29
7/17/2016
26
http://www.nxtprograms.com/claw_car/steps.html
5/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
6/29
7/17/2016
27
http://www.nxtprograms.com/claw_car/steps.html
7/29
7/17/2016
Note: When attaching the second claw to the motor, you will need to rotate the small gray axle slightly until
it lines up with the cross hole on the other claw.
http://www.nxtprograms.com/claw_car/steps.html
8/29
7/17/2016
28
http://www.nxtprograms.com/claw_car/steps.html
9/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
10/29
7/17/2016
29
http://www.nxtprograms.com/claw_car/steps.html
11/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
12/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
13/29
7/17/2016
30
31
http://www.nxtprograms.com/claw_car/steps.html
14/29
7/17/2016
Important: Make sure both sides of the claw are open all the way before putting the gears on. This will
ensure that the claw will open and close symmetrically.
32
http://www.nxtprograms.com/claw_car/steps.html
15/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
16/29
7/17/2016
Important: Make sure both sides of the claw are still open all the way before putting on the L-shaped beam.
http://www.nxtprograms.com/claw_car/steps.html
17/29
7/17/2016
33
http://www.nxtprograms.com/claw_car/steps.html
18/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
19/29
7/17/2016
34
http://www.nxtprograms.com/claw_car/steps.html
20/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
21/29
7/17/2016
Attach the claw to the bottom of the robot as shown below. There are five black pegs that need to go in.
http://www.nxtprograms.com/claw_car/steps.html
22/29
7/17/2016
Attach the claw to the bottom of the robot as shown below. There are five black pegs that need to go in.
This is what it should look like from the top when the claw is properly attached.
http://www.nxtprograms.com/claw_car/steps.html
23/29
7/17/2016
35
http://www.nxtprograms.com/claw_car/steps.html
24/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
25/29
7/17/2016
36
Re-attach the two motor wires. Looking at the NXT brick right-side-up, the left motor should attach to port
B on the NXT, and the right wire should attach to port C on the NXT. You can route the wires under the
chassis side beam to keep them out of the way, as shown below.
37
Use the shortest wire to attach the claw motor to port A on the NXT brick. You can route the wire under
the round chassis cross support to keep it off the ground, as shown below.
http://www.nxtprograms.com/claw_car/steps.html
26/29
7/17/2016
http://www.nxtprograms.com/claw_car/steps.html
27/29
7/17/2016
38
Reattach the two controller wires to the NXT brick, making sure that the light sensor wire goes to port 3 on
the NXT and the the touch sensor wire goes to port 4 on the NXT.
Challenges
http://www.nxtprograms.com/claw_car/steps.html
28/29
7/17/2016
Practice driving and using the claw with the remote control, then see if you can drive up to a plastic
NXT ball, grab it, take it somewhere else, and then let it go. There is no way to back up with the
Claw Control program, so you can just pull back on the controller wires when you need to back up.
The claw will grab and hold lots of other things besides balls. See what other kinds of things you can
grab, hold, and drive with.
For an advanced programming challenge, see if you can understand enough of the Claw Control
program to modify it to control something else that you build. See the Challenges section at the end
of the Car with Game Controller Project for hints on how to get started, because the Claw Control
program is based on the Game_Control program. In addition to the six "BC" Move blocks for the
driving, the Claw Control program adds three "A" Move blocks to open and close the claw (one is just
to force it open at the beginning of the program).
Home
Projects
Help
Contacts
http://www.nxtprograms.com/claw_car/steps.html
29/29