Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Manual
Introduction
Only install and start the Test Sieve shaker after having read the
following operating instructions.
The operating instructions give important information about the secure, appropriate
and economic operation of the Test Sieve shaker. They should be respected in
order to avoid any dangers as well as to maximize the reliability and durability of
the machine.
The safety instructions and regulations of prevention of accidents, as well as the
different protective recommendations of the technical associations and employers
liability insurance associations, have to be strictly observed when using the
machine.
If used properly, the construction of the machine guarantees that it runs and can
be operated without any risk to persons.
The warranty does not apply to damages caused by improper use due
to a non-respect of the operating instructions.
All pictures and drawings in these operating instructions are general illustrations. They do not
reflect the construction in detail.
The technical data and dimensions are without obligation, claims cannot be derived.
We reserve technical changes of the machine described below, without changing the
operating instructions.
All rights on these operating instructions, the added drawings and other documents remain to
W.S. Tyler. So are the rights on disposition, copying and passing on, including trademark
registering.
Transport
The W.S. Tyler Test Sieve Shaker Ro-Tap Model E is delivered completely assembled,
except the guide rods.
If not otherwise agreed, it is packed according to the packing directives, HPE, as defined by
The National Association of Wooden Instruments, Pallets, Export Packaging and The
Society of German engineering shops.
Observe the current valid national and international directives for accident prevention. Damage
caused by improper transport will invalidate any guarantee or replacement.
Warning
Improper lifting may cause bodily harm or material damage. Only lift the machine with the
suitable equipment and by qualified persons!
2
1.
2.
3.
4.
Set values
Actual values
Entry keys
left (-)
right (+)
Start/Stop
To start the machine, press the Start button. As the unit runs, the remaining analysis time will be
shown in the display window. To stop the machine, press the start button again.
.
Picture 1
Picture 2
Elevation adjustment: As illustrated in Picture no. 2 the hand has to be placed between the
locking ring and the tensioning wheel. Then pull the locking ring upwards, allowing the tension
nut to be moved easily up and down the guide rod.
Tensioning: As illustrated in Picture no. 1 the tension nuts have to be set on the sieve cover.
The tension nuts can then be screwed down for a tighter fit.
Ro Tap Model E
Ro-Tap Model E dry
1 spanner wrench
SW 27 DIN 894 WGBv
to fix the guide rods
1 spanner wrench
SW 27 DIN 894 WGB
to fix the guide rods
Item No.
Piece
1
2
2
1
1
1
1
1
3
4
5
6
7
8
9
10
11
12
13
18
19
2
1
1
1
3
3
1
1
1
1
1
1
1
1
1
2
1
20
14
15
16
17
Designation
Nuts for clamping system Easylock
Inspection glass without hole for machine cover (dry)
Inspection glass with hole for machine cover (wet)
Cover with inspection glass
Cover without inspection glass
Cover with inspection glass and wide spreading spray diffuser
Rubber buffer
Test sieves
Guide rods, clamping system Easylock, 660 mm long
Oscillation magnet
Rubber profile for vibration body
Vibration body
Rubberized pads
Leaf spring
Base plate
Separate control unit
Front panel with control board
Rubber ring for vibration body 204 / 160
Wide spreading spray diffuser
Wide spreading spray diffuser with inspection glass
Sieve pan with outlet
Plug connection with main switch and fuse box
Plate with cable with screw fitting
Counter nut
Precision fuse, 20x5 mm, 3,15 Ampere MT (not shown in the
drawing)
Rubber seal for cover (not shown in the drawing)
Article No.
00560129
00561499
00561507
00561521
00561514
00561545
66000074
00560154
65300016
00560441
68500312
00560014
68500231
68500311
00560169
68500015
00561374
00560489
68500033
65100000
00560434
9
Warranty
All functions of the machine are inspected and checked prior to its delivery.
The machine is warranted for 12 months.
*Test Sieves are excluded from warranty
W.S. Tyler is only liable for defects resulting from flaws or faults in material. The warranty
does not apply to damages caused by transport. Repairs resulting by improper handling or
wear due to operation are excluded from the warranty. The warranty is void, if interventions
such as variations or improper repairs are affected which are outside our control.
00 - 04
If this display appears, the machine has an electronic problem and W.S. Tyler should be
contacted immediately.
Please note that W.S. Tyler Test Sieve Shakers should only be repaired and serviced by
authorized dealers. Improper repairs may result in considerable dangers for the user.
W.S. Tyler
Particle Analysis, Filtration and Industrial Screening Products
8570 Tyler Blvd.
Mentor, Ohio 44060
Phone: 800-321-6188
Fax:
440-974-0921
E-Mail: wstyler@wstyler.com
The W.S. Tyler Test Sieve Shaker Ro-Tap Model E should be serviced at least
every 2 years!
10