Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
K.S.ROY
K.PAVAN KUMAR
K.L University
Electronics and Communication Engineering
Vyas Informatics,hyderabad
K.L University
I.INTRODUCTION
Interactive online data acquisition and
control system plays a major role in the rapid
development of the rapid popularization and control
in the field of measurement and control systems. It
has been designed with the help of is that it makes the
system more complicated and not many reliable
electrical, electronics and low voltage equipment.
This makes the system more reliable and prevents
complication. It is the great demand in many
consumer applications and industries. This system
replaces several complex cable used for data
acquisition and use Atmega168 Arduino processor
and the data acquisition and control. Data acquisition
system is widely used in a number of automatic test
and measurement equipment. They are used to collect
the necessary data from input peripheral devices,
such as meters, sensors, etc.
This data acquisition system uses a 10-bit
ADC fast available ATmega168 AVR. The
ATmega168 has 16K bytes of Flash Program, 512
bytes of EEPROM and 1K byte SRAM. This system
can measure all kinds of electrical and non-electrical
signals locally and remotely. And be able to control
devices remotely. The measured data can be
ISSN: 2231-5381
http://www.ijettjournal.org
Page 1358
International Journal of Engineering Trends and Technology (IJETT) - Volume4Issue5- May 2013
Figure shows the overview of IDAC system. Every
client can access the industry directly without any
interaction using internet. IDACS shows Intelligent
Data Acquisition and Control System. This system
contains single atmega168 processor which is
programmed. Atmega168 processor is the heart of
this work.
It handles two modes at the same time, DAC and
internet modes. During DAC mode Processor can
measure signals which are coming from various
external sources and applications. And it can be used
to control the industry machineries by the control
instruction sent by client via internet. Client can
interact the industry by giving instruction on his own
system using internet.
During signal measurements Analog to digital
converter is very important, because almost every
external source is giving analog signal only. This
system has an inbuilt 10-bit ADC with 6 analogue
input channels.
III.IDACS DESIGN
IDACS design is the major part in hardware.
Atmega168 processor is a Centre core of this system.
The general hardware structure of the IDACS is
shown in Fig 2. The present data acquisition system
makes use of a 10 bit ADC available in AVR
microcontroller Atmega168. The ATmega168 has
16K bytes of Flash Program, 512 bytes EEPROM
and 1K byte SRAM. This system can measure any
kind of electrical and non-electrical signals locally as
well as remotely. And it can able to control the
devices remotely. The measured data can be
displayed on flash magic using serial to Ethernet
connector through the internet, and at the same time
can be controlled.
ISSN: 2231-5381
http://www.ijettjournal.org
Page 1359
International Journal of Engineering Trends and Technology (IJETT) - Volume4Issue5- May 2013
In the program system programming on-chip
boot
power brown-out detection reset and
programmable.
Features:
You can measure temperature accurately
than a using a thermistor.
The sensor circuitry is totally sealed and not
subject to oxidation, etc.
The LM35 generates a high output voltage
than thermocouples and may not require
that the output voltage be amplified.
These sensors use a solid-state technique to
determine the temperature. That is to say,
they dont use mercury (like old
thermometers), bimetallic strips (like in
some home thermometers or stoves), nor do
ISSN: 2231-5381
http://www.ijettjournal.org
Page 1360
International Journal of Engineering Trends and Technology (IJETT) - Volume4Issue5- May 2013
VI.PROXIMITY SENSOR
A proximity sensor is a sensor
capable of detecting the presence of nearby
objects without any physical proximity
sensor
contact.A
often
emits
an
electromagnetic field, or a beam of
electromagnetic radiation (infrared, for
example), and look for changes in the field
or return signal. The object being sensed is
known as the proximity sensor target often.
Different proximity sensor targets require
different sensors. For eg a capacitive
photoelectric sensor might be suitable for a
plastic target; inductive proximity sensor
always requires a maximum distance run
this metal that this sensor can detect is
defined "nominal range". Some sensors have
adjustments of nominal range or means to
report
a
graduated
detection
distance.Proximity sensors will have a high
reliability and long life due to the absence of
mechanical parts and lack of physical
contact between the sensor and the object
detected.
ISSN: 2231-5381
http://www.ijettjournal.org
Page 1361
International Journal of Engineering Trends and Technology (IJETT) - Volume4Issue5- May 2013
Proximity Sensor Readings And Motor Position As
Shown Below.
IX. REFERENCES
1. Design Of Online Interactive Data Acquisition And Control
System For Embedded Applications By Manivannan M, 2011.
2. Baroncini M, Placidi P, Cardinali G C, Scorzoni A 2003 Sensors
and Actuators A 109: 131.
3. Ziad Salem, Ismail Al Kamal, Alaa Al Bashar A Novel Design
of an Industrial Data Acquisition System,Proc. of Int. Conf. on
Inf. And Comm. Tech, ICTTA 2006.
4. S. Thanee S. Somkuarnpanit and K. Saetang, FPGA-Based
Multi Protocol Data Acquisition System with High Speed USB
Interface Proceedings of the international Multi Conference of
Engineers and Computer Scientists 2010 Vol II, IMCES 2010,
17,Hong Kong.
5. D. Vijendra Babu, P. Subramanian and N. Ravi Kanan,
Microblaze and Uclinux Based Data Acquisition on Spartan 3E
Proc. Of International Conference on VLSI Design and Embedded
Systems, pp1-4, 2008.
6. Clyde C. W. Robson, Samuel Silverstein, and Christian Bohm
,An Operation-Server Based Data Acquisition System
ISSN: 2231-5381
http://www.ijettjournal.org
Page 1362