Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1.
Scope
1
2
3
4
Formerly
Class
Class
Class
Class
1
2
3
4
3.
3.2 Material supplied to this specification shall conform to the requirements of Specification A 788, which
outlines additional ordering information, manufacturing
requirements, testing and retesting methods and procedures, marking, certification, product analysis variations,
and additional supplementary requirements.
2.
Referenced Documents
4.
5.
8.
8.1.1 Except when otherwise specified in accordance with Supplementary Requirement S2, the longitudinal axis of the specimens shall be parallel to the
direction of major working of the forging. For upsetdisc forgings, the longitudinal axis of the test specimen
shall be in the tangential direction.
Heat Treatment
6.1 After forging and before reheating for heat treatment, the forgings shall be cooled in such a manner
as to prevent injury and to accomplish transformation.
8.1.2 Except as specified herein, tests for acceptance shall be made after heat treatment has been
completed. When the ends of the cylindrical forgings
are closed in by reforging, the cylindrical forgings may
be annealed, normalized, or normalized and tempered
and tested prior to reforging. After reforging, the entire
forging shall be reheat treated in the same manner and
at the same temperature range as employed when the
forging was heat treated prior to certification testing.
NOTE 2Although liquid quenching from the austenitizing temperatures is more effective in enhancing impact properties, air cooling
from the austenitizing temperatures is also beneficial and may be
used instead of the normalizing procedure in 6.2.
7.
Mechanical Properties
Machining
6.
SA-266/SA-266M
Chemical Composition
8.1.3 When mutually agreed upon between manufacturer and purchaser, test specimens may be machined
from a specially forged block suitably worked and heat
treated with the production forgings. Such a special
block shall be obtained from an ingot, slab, or billet
from the same heat used to make the forgings it
represents. This block shall receive essentially the same
type of hot working and forging reduction as the
production forgings; however, a longitudinally forged
SA-266/SA-266M
2001 SECTION II
9.
Repair Welding
10.
Certification
10.1 In addition to the mandatory certification requirements of Specification A 788, the heat treatment cycle
data shall be included.
11.
Product Marking
12.
Keywords
442
TABLE 1
CHEMICAL REQUIREMENTS
Composition, %
Carbon, max
Manganese
Phosphorus, max
Sulfur, max
Silicon
Grades 1 and 2
Grade 3
Grade 4
0.30
0.401.05
0.025
0.025
0.150.35
0.35
0.801.35
0.025
0.025
0.150.35
0.30
0.801.35
0.025
0.025
0.150.35
TABLE 2
TENSILE REQUIREMENTS
Grade 1
Grades 2
and 4
Grade 3
6085
[415585]
30
[205]
23
7095
[485655]
36
[250]
20
75100
[515690]
37.5
[260]
19
38
33
30
443
SA-266/SA-266M
SA-266/SA-266M
2001 SECTION II
SUPPLEMENTARY REQUIREMENTS
One or more of the following supplementary requirements shall apply only when
specified by the purchaser in the inquiry, contract, or order. Details of these supplementary requirements shall be agreed upon between the manufacturer and the purchaser.
S1.
S6.
S2.
2 and 4
20
30
19
25
18
25
S3.
S7.
Hydrostatic Test
S8.
S5.
Product Analysis
S4.
Macroetch Test
S9.
Hardness
Grade
1
2 and 4
3
121 to 170
137 to 197
156 to 207
SA-266/SA-266M
0.25% max
0.20% max
0.08% max
CE p % C +
445