Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the measures listed below.
n
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Notice 1
The changes or modifications not expressly approved by the party responsible for
compliance could void the users authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with
the emission limits.
VOIR LA NOTICE DNSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
MS-7373
G52-73731X1
i
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL.
We take every care in the preparation of this document, but no guarantee is given as to the
correctness of its contents. Our products are under continual improvement and we reserve
the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
AMD Corporation.
NVIDIA , the NVIDIA logo, DualNet, and nForce are registered trademarks or trademarks of
Revision History
Revision
Revision History
Date
V1.0
August, 2007
ii
Safety Instructions
n
The openings on the enclosure are for air convection hence protects the equipment
from overheating. Do not cover the openings.
Make sure the voltage of the power source and adjust properly 110/220V before
connecting the equipment to the power inlet.
Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
Always Unplug the Power Cord before inserting any add-on card or module.
Never pour any liquid into the opening that could damage or cause electrical shock.
If any of the following situations arises, get the equipment checked by a service
personnel:
- The power cord or plug is damaged.
- Liquid has penetrated into the equipment.
- The equipment has been exposed to moisture.
- The equipment does not work well or you can not get it work according to User
Manual.
- The equipment has dropped and damaged.
- The equipment has obvious sign of breakage.
iii
WEEE Statement
ENGLISH
To protect the global environment and as an environmentalist, MSI must remind you
that...
Under the European Union ("EU") Directive on Waste Electrical and Electronic Equipment, Directive
2002/96/EC, which takes effect on August 13, 2005, products of "electrical and electronic equipment"
cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will
be obligated to take back such products at the end of their useful life. MSI will comply with the product take
back requirements at the end of life of MSI-branded products that are sold into the EU. You can return
these products to local collection points.
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt
Gem der Richtlinie 2002/96/EG ber Elektro- und Elektronik-Altgerte drfen Elektro- und
Elektronik-Altgerte nicht mehr als kommunale Abflle entsorgt werden. MSI hat europaweit
verschiedene Sammel- und Recyclingunternehmen beauftragt, die in die Europische Union in Verkehr
gebrachten Produkte, am Ende seines Lebenszyklus zurckzunehmen. Bitte entsorgen Sie dieses
Produkt zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgertesammelstelle in Ihrer Nhe.
FRANAIS
En tant qucologiste et afin de protger lenvironnement, MSI tient rappeler ceci...
Au sujet de la directive europenne (EU) relative aux dchets des quipement lectriques et
lectroniques, directive 2002/96/EC, prenant effet le 13 aot 2005, que les produits lectriques et
lectroniques ne peuvent tre dposs dans les dcharges ou tout simplement mis la poubelle. Les
fabricants de ces quipements seront obligs de rcuprer certains produits en fin de vie. MSI prendra en
compte cette exigence relative au retour des produits en fin de vie au sein de la communaut europenne.
Par consquent vous pouvez retourner localement ces matriels dans les points de collecte.
MSI ,
, ....
()
(
WEEE 2002/96/EC), 13 2005 , ,
, ,
. MSI
, MSI EC,
. .
ESPAOL
MSI como empresa comprometida con la proteccin del medio ambiente, recomienda:
Bajo la directiva 2002/96/EC de la Unin Europea en materia de desechos y/o equipos electrnicos, con
fecha de rigor desde el 13 de agosto de 2005, los productos clasificados como "elctricos y equipos
electrnicos" no pueden ser depositados en los contenedores habituales de su municipio, los fabricantes
de equipos electrnicos, estn obligados a hacerse cargo de dichos productos al termino de su perodo
de vida. MSI estar comprometido con los trminos de recogida de sus productos vendidos en la Unin
Europea al final de su periodo de vida. Usted debe depositar estos productos en el punto limpio
establecido por el ayuntamiento de su localidad o entregar a una empresa autorizada para la recogida de
estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan herinneren dat.
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en Electronische
producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als
vervuiling.
Fabrikanten van dit soort producten worden verplicht om producten retour te nemen aan het eind van hun
levenscyclus. MSI zal overeenkomstig de richtlijn handelen voor de producten die de merknaam MSI
iv
dragen en verkocht zijn in de EU. Deze goederen kunnen geretourneerd worden op lokale
inzamelingspunten.
SRPSKI
Da bi zatitili prirodnu sredinu, i kao preduzee koje vodi rauna o okolini i prirodnoj sredini, MSI mora da
vas podesti da
Po Direktivi Evropske unije ("EU") o odbaenoj ekektronskoj i elektrinoj opremi, Direktiva 2002/96/EC,
koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju pod "elektronsku i elektrinu opremu" ne
mogu vie biti odbaeni kao obian otpad i proizvoai ove opreme bie prinueni da uzmu natrag ove
proizvode na kraju njihovog uobiajenog veka trajanja. MSI e potovati zahtev o preuzimanju ovakvih
proizvoda kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode
moete vratiti na lokalnim mestima za prikupljanje.
POLSKI
Aby chroni nasze rodowisko naturalne oraz jako firma dbajca o ekologi, MSI przypomina, e...
Zgodnie z Dyrektyw Unii Europejskiej ("UE") dotyczc odpadw produktw elektrycznych i
elektronicznych (Dyrektywa 2002/96/EC), ktra wchodzi w ycie 13 sierpnia 2005, tzw. produkty oraz
wyposaenie elektryczne i elektroniczne " nie mog by traktowane jako mieci komunalne, tak wic
producenci tych produktw bd zobowizani do odbierania ich w momencie gdy produkt jest
wycofywany z uycia. MSI wypeni wymagania UE, przyjmujc produkty (sprzedawane na terenie Unii
Europejskiej) wycofywane z uycia. Produkty MSI bdzie mona zwraca w wyznaczonych punktach
zbiorczych.
TRKE
evreci zelliiyle bilinen MSI dnyada evreyi korumak iin hatrlatr:
Avrupa Birlii (AB) Kararnamesi Elektrik ve Elektronik Malzeme At, 2002/96/EC Kararnamesi altnda 13
Austos 2005 tarihinden itibaren geerli olmak zere, elektrikli ve elektronik malzemeler dier atklar gibi
pe atlamayacak ve bu elektonik cihazlarn reticileri, cihazlarn kullanm sreleri bittikten sonra rnleri
geri toplamakla ykml olacaktr. Avrupa Birliine satlan MSI markal rnlerin kullanm sreleri
bittiinde MSI rnlerin geri alnmas istei ile ibirlii ierisinde olacaktr. rnlerinizi yerel toplama
noktalarna brakabilirsiniz.
ESKY
Zle nm na ochran ivotnho prosted - spolenost MSI upozoruje...
Podle smrnice Evropsk unie ("EU") o likvidaci elektrickch a elektronickch vrobk 2002/96/EC platn
od 13. srpna 2005 je zakzno likvidovat "elektrick a elektronick vrobky" v bnm komunlnm
odpadu a vrobci elektronickch vrobk, na kter se tato smrnice vztahuje, budou povinni odebrat
takov vrobky zpt po skonen jejich ivotnosti. Spolenost MSI spln poadavky na odebrn vrobk
znaky MSI, prodvanch v zemch EU, po skonen jejich ivotnosti. Tyto vrobky mete odevzdat v
mstnch sbrnch.
MAGYAR
Annak rdekben, hogy krnyezetnket megvdjk, illetve krnyezetvdknt fellpve az MSI
emlkezteti nt, hogy ...
Az Eurpai Uni (EU") 2005. augusztus 13-n hatlyba lp, az elektromos s elektronikus
berendezsek hulladkairl szl 2002/96/EK irnyelve szerint az elektromos s elektronikus
berendezsek tbb nem kezelhetek lakossgi hulladkknt, s az ilyen elektronikus berendezsek
gyrti kteless vlnak az ilyen termkek visszavtelre azok hasznos lettartama vgn. Az MSI
betartja a termkvisszavtellel kapcsolatos kvetelmnyeket az MSI mrkanv alatt az EU-n bell
rtkestett termkek esetben, azok lettartamnak vgn. Az ilyen termkeket a legkzelebbi
gyjthelyre viheti.
ITALIANO
Per proteggere lambiente, MSI, da sempre amica della natura, ti ricorda che.
In base alla Direttiva dellUnione Europea (EU) sullo Smaltimento dei Materiali Elettrici ed Elettronici,
Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti alla categoria dei Materiali
Elettrici ed Elettronici non possono pi essere eliminati come rifiuti municipali: i produttori di detti materiali
saranno obbligati a ritirare ogni prodotto alla fine del suo ciclo di vita. MSI si adeguer a tale Direttiva
ritirando tutti i prodotti marchiati MSI che sono stati venduti allinterno dellUnione Europea alla fine del
loro ciclo di vita. possibile portare i prodotti nel pi vicino punto di raccolta.
Table of Content
English ......................... 1
Franais ....................... 13
Deutsch ........................ 25
....................... 37
........................ 49
........................ 61
........................... 73
vi
INTRODUCTION
Thank you for choosing the K9AGM4 v1.0 Series (MS-7373 v1.x) Micro-ATX mainboard.
The K9AGM4 v1.0 Series is design based on AMD RS690V & SB600 chipsets for optimal
system efficiency. Designed to fit the advanced AMD Socket AM2 Athlon64/ Athlon64 X2/
Sempron processor, the K9AGM4 v1.0 Series deliver a high performance and professional
desktop platform solution.
Layout
CPUFAN1
Top : mouse
Bottom: keyboard
ATX1
Bottom:
COM A
VGA Port
USB ports
T:Line-In
M:Line- Out
B:Mic-In
IDE 1
JPW1
AMD
RS690V
DIMM1
JTPM1
DIMM2
LAN
Chip
AMD
SB600
PCI1
SATA2
JCI1
PCI _EX2
I/O
Chip
ALC888
SATA1
BATT
+
PCI 2
JBAT1
JAUD1
JCD1
FDD1
SYSFAN1
JUSB1
JFP2
JFP1
SPECIFICATIONS
Processor Support
Supported FSB
l 1000 MHz
Chipset
Memory Support
l DDR2 800/667/533 DRAM (4GB Max)
l 2 DDR2 DIMMs (240pin / 1.8V)
(For more information on compatible components, please visit
http://global.msi.com.tw/index.php?func=testreport)
LAN
l Supports 10/100 Fast Ethernet by 8101E
l Or supports 10/ 100/ 1000 Ethernet by 8111B (optional)
Audio
IDE
l 1 IDE port by SB600
l Supports Ultra DMA 66/100/133 mode
l Supports PIO, Bus Master operation mode
SATA
l 2 SATAII ports by SB600, supports 2 SATA device
l Supports storage and data transfers at up to 300 MB/s
Floppy
l 1 floppy port
l Supports 1 FDD with 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB
Connectors
l Back panel
- 1 PS/2 mouse port
- 1 PS/2 keyboard port
- 1 serial port
- 1 VGA port
- 1 parallel port supporting SPP/EPP/ECP mode
- 4 USB 2.0 Ports
- 1 LAN jack (10/100)
- 3 flexible audio jacks
l On-Board Pinheaders
- 1 USB 2.0 pinheader
- 1 Front-Audio pinheader
- 1 CD-in connector
Slots
l 1 PCI Express x16 slot
l 2 PCI slots
Form Factor
l Micro-ATX (24.4cm X 20.4 cm)
Mounting
l 6 mounting holes
REAR PANEL
The rear panel provides the following connectors:
Parallel Port
LAN
Mouse
Line In
USB Ports
Line Out
Mic In
Keyboard
COM port
VGA port
USB Ports
HARDWARE SETUP
This chapter tells you how to install the CPU, memory modules, and expansion cards, as
well as how to setup the jumpers on the mainboard. It also provides the instructions on
connecting the peripheral devices, such as the mouse, keyboard, etc. While doing the
installation, be careful in holding the components and follow the installation procedures.
2.
3.
4.
5.
90 degree
Correct CPU
placement
Gold arrow
Press down
the CPU
Close
the lever
1.
2.
3.
4.
Important:
Overheating will seriously damage the CPU and system. Always make sure the cooling fan
can work properly to protect the CPU from overheating.
Make sure that you apply an even layer of heat sink paste (or thermal tape) between the
CPU and the heatsink to enhance heat dissipation.
While replacing the CPU, always turn off the ATX power supply or unplug the power supply
power cord from the grounded outlet first to ensure the safety of CPU.
The memory module has only one notch on the center and will only fit in the right
orientation.
2.
Insert the memory module vertically into the DIMM slot. Then push it in until the
golden finger on the memory module is deeply inserted in the DIMM slot. You can
barely see the golden finger if the memory module is properly inserted in the DIMM
slot.
3.
The plastic clip at each side of the DIMM slot will automatically close.
Notch
Volt
Important:
DDR2 memory modules are not interchangeable with DDR and the DDR2 standard is not
backwards compatible. You should always install DDR2 memory modules in the DDR2
DIMM slots.
In Dual-Channel mode, make sure that you install memory modules of the same type and
density in different channel DIMM slots.
To enable successful system boot-up, always insert the memory modules into the DIMM1
first.
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
Important:
Make sure that all the connectors are connected to proper ATX power supplies to ensure
stable operation of the mainboard.
Power supply of 350 watts (and above) is highly recommended for system stability.
+12V Sensor
The fan power connectors support system cooling fan with +12V.
When connecting the wire to the connectors, always note that the
red wire is the positive and should be connected to the +12V; the
black wire is Ground and should be connected to GND. If the
mainboard has a System Hardware Monitor chipset on-board, you
must use a specially designed fan with speed sensor to take
advantage of the CPU fan control.
Control
GND
+12V
GND
Sensor
USB1+
GND
USB1-
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
GND
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
JFP1
- -
9
10
1
2
Power Power
Switch LED
Speaker
2
1
JFP2
8
7
Power LED
CINTRU
GND
1 2
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
1
2
1 2 3
1 2 3
Keep Data
1 2 3
Clear Data
Important:
You can clear CMOS by shorting 2-3 pin while the system is off. Then return to 1-2 pin
position. Avoid clearing the CMOS while the system is on; it will damage the mainboard.
The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that
comply with PCI specifications.
Important:
When adding or removing expansion cards, make sure that you unplug the power supply
first. Meanwhile, read the documentation for the expansion card to configure any
necessary hardware or software settings for the expansion card, such as jumpers,
switches or BIOS configuration.
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
BIOS Setup
Power on the computer and the system will start POST (Power On Self Test) process. When
the message below appears on the screen, press <DEL> key to enter Setup.
Press DEL to enter SETUP
If the message disappears before you respond and you still wish to enter Setup, restart the
system by turning it OFF and On or pressing the RESET button. You may also restart the
system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
Main Page
10
Frequency/Voltage Control
11
Spread Spectrum
When the motherboards clock generator pulses, the extreme values (spikes) of the pulses
create EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI
generated by modulating the pulses so that the spikes of the pulses are reduced to flatter
curves. If you do not have any EMI problem, leave the setting at Disabled for optimal system
stability and performance. But if you are plagued by EMI, set to Enabled for EMI reduction.
Remember to disable Spread Spectrum if you are overclocking because even a slight jitter
can introduce a temporary boost in clock speed which may just cause your overclocked
processor to lock up.
Important:
If you do not have any EMI problem, leave the setting at [Disabled] for optimal system
stability and performance. But if you are plagued by EMI, select the value of Spread
Spectrum for EMI reduction.
The greater the Spread Spectrum value is, the greater the EMI is reduced, and the system
will become less stable. For the most suitable Spread Spectrum value, please consult your
local EMI regulation.
Remember to disable Spread Spectrum if you are overclocking because even a slight jitter
can introduce a temporary boost in clock speed which may just cause your overclocked
processor to lock up.
12
INTRODUCTION
Flicitations, vous venez dacqurir une carte mre des sries Micro-ATX K9AGM4 v1.0
(MS-7373 v1.x). Les K9AGM4 v1.0 sries sont bases sur les chipsets AMD RS690V &
SB600 offrant un systme trs performant. La carte fonctionne avec les processeurs AMD
Socket AM2 Athlon64/ Athlon64 X2/ Sempron avanc 1000MHz System Bus Frequencies.
Les Sries K9AGM4 v1.0 sont trs performantes et offrent une solution adapte tant aux
professionnels quaux particuliers.
Schma
CPUFAN1
Top : mouse
Bottom: keyboard
ATX1
Bottom:
COM A
VGA Port
USB ports
T:Line-In
M:Line- Out
B:Mic-In
IDE 1
JPW1
AMD
RS690V
DIMM1
JTPM1
DIMM2
LAN
Chip
AMD
SB600
PCI1
SATA2
JCI1
PCI _EX2
I/O
Chip
ALC888
SATA1
BATT
+
PCI 2
JBAT1
JAUD1
JCD1
FDD1
13
SYSFAN1
JUSB1
JFP2
JFP1
SPCIFICITS
Processeurs Supports
l Les processeurs AMD Athlon64 / Athlon64 X2/ Sempron dans le paquet de socket AM2
l Supporte un connecteur de 4 pins du ventilateur de CPU avec le Contrleur de la vitesse
du ventilateur.
(Pour plus dinformation sur le CPU, veuillez visiter
http://global.msi.com.tw/index.php?func=cpuform)
FSB Support
l 1000 MHz
Chipset
Mmoire Support
l DDR2 800/667/533 DRAM (4GB Max)
l 2 DDR2 DIMMs (240pin / 1.8V)
(Pour plus dinformation, veuillez visiter http://global.msi.com.tw/index.php?func=testreport)
LAN
l Supporte 10/100 Fast Ethernet par 8101E
l Ou supporte 10/ 100/ 1000 Ethernet par 8111B (optionnel)
Audio
IDE
l 1 port IDE par SB600
l Supporte le mode Ultra DMA 66/100/133
l Supporte PIO, le mode opration Bus Master
SATA
l 2 ports SATAII par SB600, supporte 2 SATA device
l Supporte stockage et un taux de transfert jusqu 300 MB/s
Disquette
l 1 port de disquette
l Supporte 1 FDD avec 360KB, 720KB, 1.2MB, 1.44MB et 2.88MB
14
Connecteurs
l Panneau arrire
- 1 port souris PS/2
- 1 port clavier PS/2
- 1 port srie
- 1 port VGA
- 1 port parallle supportant SPP/EPP/ECP mode
- 4 ports USB 2.0
- 1 jack LAN (10/100)
- 3 audio jacks flexibles
l Connecteurs intgrs
- 1 connecteur USB 2.0
- 1 connecteur Audio avant
- 1 connecteur CD-in
Slots
l 1 slot PCI Express x16
l 2 slots PCI
Dimension
l Micro-ATX (24.4cm X 20.4 cm)
Montage
l 6 trous de montage
15
Panneau Arrire
Le panneau arrire dispose les connecteurs suivants:
Parallel Port
LAN
Mouse
Line In
USB Ports
Line Out
Mic In
Keyboard
COM port
VGA port
USB Ports
INSTALLATION MATRIEL
Ce chapitre vous indique comment installer le CPU, les modules de mmoire, les cartes
dextension et comment installer les cavaliers sur la carte. Il explique galement comment
connecter priphriques tels que la souris, le clavier etc. Lors de linstallation du matriel,
veuillez suivre les instructions de montage pour viter dendommager quoi que ce soit.
2.
3.
4.
5.
90 degree
Correct CPU
placement
Gold arrow
Press down
the CPU
Close
the lever
16
1.
2.
3.
4.
Important:
Le surchauffe peut srieusement endommager le CPU et le systme. Toujours assurez que
le ventilateur fonctionne correctement pour protger le CPU du surchauffe.
Assurez-vous que vous appliquez une pte de dissipateur termique (ou bande thermique)
entre le CPU et le dissipateur thermique afin damliorer la dissipation thermique.
Quand vous remplacez le CPU, toujours teignez lalimentation ou dbrochez le cordon de
la sortie du sol en premier pour ensurer la scurit du CPU.
2.
3.
Notch
Volt
Important:
Les modules de mmoire DDR2 ne sont pas interchangeables par DDR et vice versa. Vous
devez installer toujours les modules de mmoire DDR2 dans les slots DDR2 DIMM.
Dans le mode Dual-Channel, assurez-vous que vous installez les modules de mmoire du
mme type et de la mme densit dans des slots DIMM de canneaux diffrents.
Pour lancer avec succs votre ordinateur, insrez tout dabord les modules de mmoire
dans le DIMM1.
17
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
Important:
Assurez-vous que tous les connecteurs sont relis lalimentation ATX pour assurer une
stabilit de la carte mre.
Lalimentation 350 watts (ou suprieur) est recommande pour la stabilit du systme.
Connecteurs dalimentation du
ventilateur: CPUFAN1, SYSFAN1
Les connecteurs dalimentation du systme de refroidissement
supportent un systme de refroidissement de +12V. Lors de la
connexion du cble, assurez-vous que le fil rouge soit connect au
+12V et le fil noir connect au GND. Si la carte mre possde un
systme de gestion intgr, vous devez utiliser un ventilateur ayant
ces caractristiques si vous voulez contrler le ventilateur du CPU.
18
+12V Sensor
Control
GND
+12V
GND
Sensor
USB1+
GND
USB1-
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
GND
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
JFP1
- -
9
10
1
2
Power Power
Switch LED
Speaker
2
1
JFP2
8
7
Power LED
CINTRU
GND
1 2
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
19
1
2
1 2 3
1 2 3
Keep Data
1 2 3
Clear Data
Important:
Vous pouvez effacer le CMOS en positionnant le cavalier sur les broches 2-3 lorsque le
PC nest pas allum. Puis il faut remettre le cavalier en position 1-2. Ne surtout pas
effacer le CMOS lorsque le PC est allum, cela endommagera la carte mre.
Le slot PCI supporte la carte LAN, la carte SCSI, la carte USB, et dautres cartes ajoutes
qui obissent aux spcificits PCI.
Important:
Lorsque vous ajoutez ou retirez une carte dextension, assurez-vous que le PC nest pas
reli au secteur. Lisez la documentation pour faire les configurations ncessaires du
matriel ou du logiciel de la carte dextension, tels que cavaliers, commutateurs ou la
configuration du BIOS.
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
20
BIOS Setup
Lorsque le PC dmarre, le processus de POST (Power On Self Test) se met en route.
Quand le message ci-dessous apparat lcran, appuyer sur <DEL> pour accder au
Setup.
Appuyer sur DEL pour accder au SETUP
Si le message disparat avant que nayez appuy sur la touche, redmarrez le PC avec
laide du bouton RESET. Vous pouvez aussi redmarrer en utilisant la combinaison des
touches <Ctrl>, <Alt>, et <Delete>.
Page Principale
21
22
Frequency/Voltage Control
23
Spread Spectrum
Les cartes mres crent des interfrences lectromagntiques (EMI - Electromagnetic
Interference). La fonction Spread Spectrum rduit ces EMI. Si vous navez pas de problme
dEMI, laissez loption sur Disabled, ceci vous permet davoir une stabilit du systme et des
performances optimales. Dans le cas contraire, choisissez Enabled pour rduire les EMI.
Noubliez pas de dsactiver cette fonction si vous voulez faire de loverclocking, afin dviter
tout problme.
Important:
Si vous navez pas de problme dEMI, laissez loption sur [Disabled], ceci vous permet
davoir une stabilit du systme et des performances optimales. Dans le cas contraire,
choisissez Spread Spectrum pour rduire les EMI.
Plus la valeur Spread Spectrum est importante, plus les EMI sont rduites, et le systme
devient moins stable. Pour la valeur Spread Spectrum la plus convenable, veuillez
consultez le rglement EMI local.
Noubliez pas de dsactiver la fonction Spread Spectrum si vous tes en train doverclocker
parce que mme un battement lger peut causer un accroissement temporaire de la vitesse
de lhorloge qui verrouillera votre processeur overclock.
24
EINLEITUNG
Danke, dass Sie das K9AGM4 v1.0 Series (MS-7373 v1.x) Micro-ATX Mainboard gewhlt
haben. Das K9AGM4 v1.0 Series basiert auf dem AMD RS690V & SB600 Chipsatz und
ermglicht so ein optimales und effizientes System. Entworfen, um den hochentwickelten
AMD Socket AM2 Athlon64/ Athlon64 X2/ Sempron Prozessoren, stellt das K9AGM4 v1.0
Series die ideale Lsung zum Aufbau eines professionellen Hochleistungsdesktopsystems
dar.
Layout
CPUFAN1
Top : mouse
Bottom: keyboard
ATX1
Bottom:
COM A
VGA Port
USB ports
T:Line-In
M:Line- Out
B:Mic-In
IDE 1
JPW1
AMD
RS690V
DIMM1
JTPM1
DIMM2
LAN
Chip
AMD
SB600
PCI1
SATA2
JCI1
PCI _EX2
I/O
Chip
ALC888
SATA1
BATT
+
PCI 2
JBAT1
JAUD1
JCD1
FDD1
25
SYSFAN1
JUSB1
JFP2
JFP1
SPEZIFIKATIONEN
Prozessoren
FSB (Front-Side-Bus)
l 1000 MHz
Chipsatz
Speicher
l DDR2 800/667/533 DRAM (max. 4GB)
l 2 DDR2 DIMMs (240 Pin / 1.8V)
(Weitere Informationen zu kompatiblen Speichermodulen finden Sie unter
http://global.msi.com.tw/index.php?func=testreport)
LAN
l Untersttzt 10/100 Fast Ethernet ber 8101E
l Oder unterstutzt 10/ 100/ 1000 Ethernet ber 8111B (optional)
Audio
IDE
l 1 IDE Port ber SB600
l Untersttzt die Betriebmodi Ultra DMA 66/100/133 mode
l Untersttzt die Betriebmodi PIO, Bus Mastering
SATA
l 2 SATAII Ports ber SB600, untersttzt 2 SATA Gert
l Untersttzt Datenbertragungsraten von bis zu 300 MB/s
Disketten Laufwerk
l 1 Disketten Anschluss
l Untersttzt ein Diskettenlaufwerk mit 360KB, 720KB, 1.2MB, 1.44MB oder 2.88MB
Kapazitt
26
Anschlsse
l Hintere Ein-/ und Ausgnge
- 1 PS/2 Mausanschluss
- 1 PS/2 Tastaturanschlus
- 1 Serielle Schnittstelle
- 1 VGA Port
- 1 Parallele Schnittstelle, untersttzt die Betriebsmodi SPP/EPP/ECP
- 4 USB 2.0 Anschlsse
- 1 LAN Buchse (10/100)
- 3 Audiobuchsen
l On-Board Stiftleiste / Anschlsse
- 1 USB 2.0 Stiftleisten
- 1 Audio Stiftleiste fr Gehuse Audio Ein-/ Ausgnge
- 1 CD Stiftleiste fr Audio Eingang
Schnittstellen
l 1 PCI Express x16 Schnittstelle
l 2 PCI Schnittstellen
Form Faktor
l Micro-ATX (24.4cm X 20.4 cm)
Mountage
l 6 Montagebohrungen
27
Hinteres Anschlusspanel
Das hintere Anschlusspanel verfgt ber folgende Anschlsse:
Parallel Port
LAN
Mouse
Line In
USB Ports
Line Out
Mic In
Keyboard
COM port
VGA port
USB Ports
HARDWARE SETUP
Dieses Kapitel informiert Sie darber, wie Sie die CPU, Speichermodule und
Erweiterungskarten einbauen, des weiteren darber, wie die Steckbrcken auf dem
Mainboard gesetzt werden. Zudem bietet es Hinweise darauf, wie Sie Peripheriegerte
anschlieen, wie z.B. Maus, Tastatur, usw. Handhaben Sie die Komponenten whrend des
Einbaus vorsichtig und halten Sie sich an die vorgegebene Vorgehensweise beim Einbau.
2.
3.
4.
5.
28
Sliding
the plate
90 degree
Correct CPU
placement
Gold arrow
Press down
the CPU
Close
the lever
2.
3.
4.
Wichtig:
berhitzung beschdigt die CPU und das System nachhaltig, stellen Sie stets eine korrekte
Funktionsweise des CPU Khlers sicher, um die CPU vor berhitzung zu schtzen.
Stellen Sie bitte sicher, dass Sie auf der CPU einen Khlkrper mit aktiven Prozessorlfter
anbringen, um berhitzung zu vermeiden..
Stellen Sie whrend eines CPU-Wechsels immer sicher, dass das ATX Netzteil
ausgeschaltet ist und ziehen Sie zuerst den Netzstecker, um die Unversehrtheit Ihrer CPU
zu gewhrleisten.
Die Speichermodule haben nur eine Kerbe in der Mitte des Moduls. Sie passen nur in
einer Richtung in den Sockel.
2.
Setzen Sie den DIMM- Speicherbaustein senkrecht in den DIMM- Sockel, dann
drcken Sie ihn hinein, bis die goldenen Kontakte tief im Sockel sitzen. Wenn das
Speichermodule richtig im DIMM Steckplatz eingesetzt wird, knnen Sie den
goldenen Finger kaum sehen.
3.
Die Plastikklammern an den Seiten des DIMM- Sockels schlieen sich automatisch.
Notch
Volt
29
Wichtig:
DDR2 und DDR knnen nicht untereinander getauscht werden und der Standard DDR2 ist
nicht rckwrtskompatibel, installieren Sie DDR2 Speichermodule stets in DDR2 DIMM
Slots und DDR Speichermodule stets in DDR DIMM Slots.
Stellen Sie sicher, dass Sie im Zweikanalbetrieb Speichermodule des selben Typs und der
gleichen Dichte einsetzen.
Um einen sicheren Systemstart zu gewhrleisten, bestcken Sie immer DIMM 1 zuerst.
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
Wichtig:
Stellen Sie die Verbindung aller drei Anschlsse mit einem angemessenem ATX Netzteil
sicher, um den stabilen Betrieb des Mainboards sicher zu stellen.
Netzteile mit 350 Watt (und mehr) werden aus Grnden der Systemstabilitt dringend
empfohlen.
30
Stromanschlsse fr Lfter :
CPUFAN1, SYSFAN1
+12V Sensor
Control
GND
+12V
GND
Sensor
USB1+
GND
USB1-
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
GND
MIC2_JD
Audioanschluss des
Frontpanels: JAUD1
VCC5
31
(2)GND
(1)MIC_L
NC
Line_JD(10)
Line-out_L(9)
Reset HDD
Switch LED
+
- -
9
10
JFP1
1
2
Power Power
Switch LED
Speaker
2
1
JFP2
8
7
Power LED
Gehusekontaktschalter: JCI1
Dieser Anschluss wird mit einem Kontaktschalter verbunden. Wird das
Gehuse geffnet, wird der Schalter geschlossen und das System
zeichnet dies auf und gibt auf dem Bildschirm eine Warnung aus. Um die
Warnmeldung zu lschen, muss das BIOS aufgerufen und die
Aufzeichnung gelscht werden.
1
2
CINTRU
GND
1 2
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
1 2 3
1 2 3
Keep Data
1 2 3
Clear Data
Wichtig:
Sie knnen den CMOS lschen, indem Sie die Pins 2-3 verbinden, whrend das System
ausgeschaltet ist. Kehren Sie danach zur Pinposition 1-2 zurck. Lschen Sie den CMOS
nicht, solange das System angeschaltet ist, dies wrde das Mainboard beschdigen.
32
Der PCI Express x 16 Slot untersttzt die Datenubertragunsraten von bis zu 4.0 GB/s.
Die PCI Steckpltze untersttzt LAN Karte, SCSI Karte, USB Karte und andere
Zusatzkarten Karte,die mit PCI Spezifikationen bereinstimmen.
Wichtig:
Stellen Sie vor dem Einsetzen oder Entnehmen von Karten sicher, dass Sie den
Netzstecker gezogen haben. Studieren Sie bitte die Anleitung zur Erweiterungskarte, um
jede notwendige Hard - oder Softwareeinstellung fr die Erweiterungskarte vorzunehmen,
sei es an Steckbrcken (Jumpern), Schaltern oder im BIOS.
Reihenfolge2
Reihenfolge3
Reihenfolge4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
33
BIOS Setup
Nach dem Einschalten beginnt der Computer den POST (Power On Self Test Selbstberprfung nach Anschalten). Sobald die Meldung unten erscheint, drcken Sie die Taste
<Entf>(<Del>), um das Setup aufzurufen.
Press DEL to enter SETUP
Nach dem Einschalten beginnt der Computer den POST (Power On Self Test Selbstberprfung nach Anschalten). Sobald die Meldung unten erscheint, drcken Sie die Taste
<Entf>(<Del>), um das Setup aufzurufen Sie gleichzeitig die Tasten <Strg>,<Alt> und
<Entf> drcken (bei manchen Tastaturen <Ctrl>, <Alt> und <Delete>.
Main Page
34
H/W Monitor
Dieser Eintrag zeigt den Status der CPU, des Lfters und allgemeine Warnungen zum
generellen Systemstatus.
Frequency/Voltage Control
Hier knnen Sie Einstellungen zu Frequenzen und Spannungen vornehmen.
Load Optimized Defaults
Hier knnen Sie die BIOS- Werkseinstellungen fr stabile Systemleistung laden.
BIOS Setting Password
Verwenden Sie dieses Men, um das Kennwort fr das BIOS einzugeben.
Save & Exit Setup
Abspeichern der BIOS-nderungen im CMOS und verlassen des BIOS.
Exit Without Saving
Verlassen des BIOS ohne Speicherung, vorgenommene nderungen verfallen.
Frequency/Voltage Control
35
36
K9AGM4 v1.0 (MS-7373 v1.x)
Micro-ATX. K9AGM4 v1.0
CPUFAN1
Top : mouse
Bottom: keyboard
ATX1
Bottom:
COM A
VGA Port
USB ports
T:Line-In
M:Line- Out
B:Mic-In
IDE 1
JPW1
AMD
RS690V
DIMM1
JTPM1
DIMM2
LAN
Chip
AMD
SB600
PCI1
SATA2
JCI1
PCI _EX2
I/O
Chip
ALC888
SATA1
BATT
+
PCI 2
JBAT1
JAUD1
JCD1
FDD1
37
SYSFAN1
JUSB1
JFP2
JFP1
FSB
l 1000
l : AMD RS690V
l : AMD SB600
LAN
l 10/100 Fast Ethernet (Realtek RTL 8101E)
l 10/ 100/ 1000 Ethernet 8111B ()
l Realtek ALC888
l Flexible 5.1-channel audio-out function
l Azalia 1.0
IDE
l 1 IDE, SB600
l Ultra DMA 66/100/133
l PIO, Bus Master
SATA
l 2 SATAII SB600, 2 SATA
l 300 /
Floppy
l 1 floppy
l 1 FDD 360, 720 , 1.2, 1.44 2.88
38
l
- 1 PS/2
- 1 PS/2
- 1
- 1 VGA
- 1 SPP/EPP/ECP
- 4 USB 2.0
- 1 LAN (10/100)
- 3 /
l
- 1 USB 2.0
- 1
- 1 CD-in
l Micro-ATX (24.4 X 20.4)
l 6
39
:
Parallel Port
LAN
Mouse
Line In
USB Ports
Line Out
Mic In
Keyboard
COM port
VGA port
USB Ports
, ,
, .
, , ,
.. ,
.
2.
3.
4.
5.
CPU, ,
.
, .
(Gold
arrow) CPU.
, . CPU
.
CPU
,
. ,
CPU
.
90 degree
Correct CPU
placement
Gold arrow
Press down
the CPU
CPU
. CPU
,
CPU ,
.
Close
the lever
40
.
.
:
Socket AM2.
.
1.
.
.
2.
,
.
.
3.
4.
CPU
.
:
.
, ,
.
,
.
CPU, ,
.
1.
2.
3.
DIMM
.
. ,
( ).
.
Notch
Volt
:
DDR2 DDR, DDR2
. DDR2
DDR2.
, ,
DIMM .
, DIMM1.
41
24-
ATX: ATX1
24-
ATX .
, ,
.
.
20
( ).
ATX 12V: JPW1
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
12
.
:
, ATX .
350 ( )
.
: FDD1
360,
720, 1.2, 1.44 2.88.
IDE: IDE1
IDE,
IDE .
:
IDE,
Slave
. ,
, ,
.
42
PS-ON#
GND
:
CPUFAN1, SYSFAN1
+12V Sensor
+12. ,
+12, -
GND.
,
USB :
JUSB1
Intel
I/O
Connectivity Design Guide,
USB HDD, , MP3 ,
, ..
Control
GND
+12V
GND
Sensor
USB1+
GND
USB1-
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
CD-In: JCD1
.
GND
MIC2_JD
: JAUD1
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
Intel
I/O Connectivity Design Guide.
:
JFP1, JFP2
. JFP1
Reset HDD
Switch LED
JFP1
- -
9
10
1
2
Power Power
Switch LED
Speaker
JFP2
2
1
8
7
Power LED
: JCI1
, .
.
.
BIOS.
43
1
2
CINTRU
GND
TPM: JTPM1
()
1 2
TPM (Trusted
Platform Module) ().
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS:
JBAT1
CMOS
,
. , CMOS ,
.
(
CMOS),
1 2 3
1 2 3
Keep Data
1 2 3
Clear Data
:
CMOS 2-3 .
1-2. CMOS
: .
44
PCI
IRQ Interrupt ReQuest (line) ,
, .
IRQ PCI PCI :
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
45
BIOS
. (POST) <DEL>.
DEL, SETUP
,
.
RESET <Ctrl>, <Alt> <Delete>.
46
47
48
K9AGM4 v1.0 (MS-7373 v1.x) Micro-ATX . K9AGM4 v1.0
CPUFAN1
Top : mouse
Bottom: keyboard
ATX1
Bottom:
COM A
VGA Port
USB ports
T:Line-In
M:Line- Out
B:Mic-In
IDE 1
JPW1
AMD
RS690V
DIMM1
JTPM1
DIMM2
LAN
Chip
AMD
SB600
PCI1
SATA2
JCI1
PCI _EX2
I/O
Chip
ALC888
SATA1
BATT
+
PCI 2
JBAT1
JAUD1
JCD1
FDD1
49
SYSFAN1
JUSB1
JFP2
JFP1
l 1000 MHz
l : AMD RS690V
l : AMD SB600
LAN
l 8101E 10/100
l 8111B 10/100/1000 ()
l Realtek ALC888
l Flexible 5.1
l Azalia 1.0
IDE
l SB600 1 IDE
l Ultra DMA 66 / 100 / 133
l PIO, ,
SATA
l SB600 2 SATAII , 2 SATA
l 300 MB/s
50
l 1
l 1 360KB, 720KB, 1.2MB, 1.44MB 2.88MB
l :
- 1 PS/2
- 1 PS/2
- 1
- 1 VGA
- 1 , SPP/EPP/ECP
- 4 USB 2.0
- 1 (10/100)
- 3
l /:
- 1 USB2.0
- 1
- 1 CD
l 6
51
:
Parallel Port
LAN
Mouse
Line In
USB Ports
Line Out
Mic In
Keyboard
COM port
VGA port
USB Ports
CPU, , , .
,,., .
3. CPU .
Sliding
the plate
CPU .
90 degree
4. CPU
.
Correct CPU
placement
5. CPU .
CPU CPU
Gold arrow
CPU
.
Press down
the CPU
Close
the lever
52
1. .
.
2. ,,
.
3.
4. CPU CPU
.
:
CPU CPU
CPU
CPU ATX , CPU .
1. . .
2. DIMM .
.
3. DIMM ..
Notch
Volt
53
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
12V CPU .
:
ATX .
, 350 ().
: FDD1
360KB, 720KB, 1.2MB, 1.44MB 2.88MB .
IDE : IDE1
IDE , IDE .
:
,
..
: CPUFAN1, SYSFAN1
+12V Senso r
+12V .
Co ntrol
GN D
+12V
+12V
GND
USB : JUSB1
Sensor
USB1+
USB1-
GND
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
CD-In : JCD1
CD-ROM .
L
54
GND
MIC2_JD
: JAUD1
VCC5
Intel I/O .
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
: JFP1, JFP2
JFP1
- -
9
10
1
2
Power Power
Switch LED
Speaker
2
1
JFP2
8
7
Power LED
: JCI1
BIOS
TPM : JTPM1 ()
TPM (Trusted Platform Module)(
)
1
2
CINTRU
GND
1 2
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS : JBAT1
CMOS RAM
.CMOS RAM
. CMOS RAM
JBAT1 ( CMOS )
. .
1 2 3
1 2 3
Keep Data
1 2 3
Clear Data
:
, 2-3 CMOS ., 1-2
. CMOS..
PCI () Express
PCI Express PCI Express .
55
PCI ()
PCI
IRQ ,.
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
56
BIOS
POST (). <DEL>
.
Press DEL to enter SETUP
. Setup,
RESET .<Ctrl>, <Alt><Delete>
.
57
H/W Monitor
CPU.
Frequency/Voltage Control/
/
Load Optimized Defaults
BIOS .
BIOS Setting PasswordBIOS
BIOS .
Save & Exit Setup
CMOS Setup .
Exit Without Saving
CMOS Setup .
58
59
Spread Spectrum ()
,() EMI().
,.
, Disabled,.
, Enabled,.,
,.(),
..
:
EMI [Disabled]
EMI Spread Spectrum EMI
Spread SpectrumEMI Spread
Spectrum( EMI
Spread Spectrum
60
K9AGM4 v1.0 (MS-7373 v1.x) Micro-ATX K9AGM4 v1.0
CPUFAN1
Top : mouse
Bottom: keyboard
ATX1
Bottom:
COM A
VGA Port
USB ports
T:Line-In
M:Line- Out
B:Mic-In
IDE 1
JPW1
AMD
RS690V
DIMM1
JTPM1
DIMM2
LAN
Chip
AMD
SB600
PCI1
SATA2
JCI1
PCI _EX2
I/O
Chip
ALC888
SATA1
BATT
+
PCI 2
JBAT1
JAUD1
JCD1
FDD1
61
SYSFAN1
JUSB1
JFP2
JFP1
FSB
l 1000 MHz
l : AMD RS690V
l : AMD SB600
LAN
l 8101E 10/100
l 8111B 10/100/1000 ()
l Realtek ALC888
l 5.1
l Azalia 1.0
IDE
l SB600 1 IDE
l Ultra DMA 66/100/133
l PIO,
SATA
l SB600 2 SATAII 2 SATA
l 300 MB
l
l 360KB720 KB1.2MB.44MB 2.88MB
62
l
- PS/2
- PS/2
-
- VGA
- SPP / EPP / ECP
- USB2.0
- LAN (10/100)
-
l
- USB2.0
-
- CD-In
63
Parallel Port
Mouse
LAN
Line
In
USB
USB Ports
Line
Out
Mic In
Keyboard
COM port
COM
VGA port
VGA
USB Ports
USB
AM2
1.
2.
90
3.
CPU ()CPU
4.
Socket
5.
Socket Socket
90 degree
Correct CPU
placement
Gold arrow
Press down
the CPU
Close
the lever
AM2
:
AM2
64
1.
2.
3.
4.
CPU CPU
:
CPU CPU
CPU ()
CPU ATX CPU
1.
2.
DIMM .
3.
VNotch
Volt
:
DDR2 DDR DDR DDR2
DDR2
DIMM1
65
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
:
ATX
350 ()
: FDD1
360KB, 720KB, 1.2MB, 1.44MB
2.88MB
IDE : IDE1
IDE IDE
:
IDE
Jumper/
: CPUFAN1, SYSFAN1
+12V
+12V GND
CPU
66
+12V Sensor
Control
GND
+12V
GND
Sensor
USB1+
USB : JUSB1
US B1-
GND
N.C.(10)
Key,no pin(9)
(2)V CC
(1)VCC
Intel /
USB USB MP3
USB0-
GND
USB0+
CD-In : JCD1
GND
MIC2_JD
:: JAUD1
VCC5
Intel /
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
: JFP1, JFP2
LED JFP1
- -
9
10
JFP1
Intel /
1
2
Power Power
Switch LED
Speaker
2
1
JFP2
8
7
Power LED
: JCI1
BIOS
TPM : JTPM1
()
()
CINTRU
GND
1 2
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
67
1
2
CMOS : JBAT1
CMOS RAM
CMOS RAM
1 2 3
1 2 3
Keep Data
1 2 3
Clear Data
:
2-3 CMOS 1-2
CMOS .
PCI Express
PCI Express PCI Express
PCI
BIOS
PCI
IRQ (Interrupt request)
PCI IRQ PCI
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
68
BIOS
POST () <DEL>
.
Press DEL to enter SETUP
Integrated Peripherals ()
69
Frequency/Voltage Control/
/
Load Optimized Defaults
BIOS
BIOS Setting Password BIOS
BIOS
Save & Exit Setup
CMOS
Exit Without Saving
70
71
Spread Spectrum
(EMI)
EMI
EMI
.
:
(EMI)[Disabled]
EMI .
EMI
72
K9AGM4 v1.0 (MS-7373 v1.x)Micro-ATX
CPUFAN1
Top : mouse
Bottom: keyboard
ATX1
Bottom:
COM A
VGA Port
USB ports
T:Line-In
M:Line- Out
B:Mic-In
IDE 1
JPW1
AMD
RS690V
DIMM1
JTPM1
DIMM2
LAN
Chip
AMD
SB600
PCI1
SATA2
JCI1
PCI _EX2
I/O
Chip
ALC888
SATA1
BATT
+
PCI 2
JBAT1
JAUD1
JCD1
FDD1
73
SYSFAN1
JUSB1
JFP2
JFP1
FSB
l 1000 MHz
l : AMD RS690V
l : AMD SB600
LAN
l 8101E 10/100
l 8111B 10/ 100/ 1000 ()
l Realtek ALC888
l 5.1
l Azalia 1.0
IDE
l SB600 1 IDE
l Ultra DMA 66/100/133
l PIO,
SATA
l SB600 2 SATAII SATA
l 300 MB/s
l 1
l 360KB, 720KB, 1.2MB, 1.44MB 2.88MB FDD1
74
l
- 1 PS/2
- 1 PS/2
- 1
- 1 VGA
- 1 SPP/EPP/ECP
- 4 USB 2.0
- 1 LAN (10/100)
- 3
l
- 1 USB 2.0
- 1
- 1 CD-in
l 6
75
:
Parallel Port
LAN
Mouse
Line In
Line Out
USB Ports
Mic In
Keyboard
COM port
VGA port
USB Ports
2.
90
CPU
3.
CPU
CPU
4.
CPU
CPU CPU
5.
CPU
CPU
CPU
CPU
76
Sliding
the plate
90 degree
Correct CPU
placement
Gold arrow
Press down
the CPU
Close
the lever
:
Socket AM2 CPU
1.
2.
3.
4.
CPU
:
CPU CPU CPU
CPU
1.
2. DIMM DIMM
3. DIMM
Notch
Volt
:
DDR2 DDR DDR2
DDR2 DIMM
1
DIMM1
77
ATX 24 : ATX1
ATX 24
20 ATX 1/13
()
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
12V CPU
+12V
GND
:
ATX
350W
FDD : FDD1
360 KB, 720 KB, 1.2MB, 1.44MB 2.88MB
IDE : IDE1
IDE IDE
:
2
ATA : SATA1/2
ATA
ATA
:
ATA 90
78
: CPUFAN1, SYSFAN1
+12V
+12V
GND
+12V Sensor
Control
GND
+12V
GND
Sensor
USB1+
USB : JUSB1
GND
USB1-
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
CD-In : JCD1
: JAUD1
GND
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
: JFP1,
JFP2
LED
Reset HDD
Switch LED
JFP1
- -
9
10
1
2
Power Power
Switch LED
Speaker
JFP2
2
1
8
7
Power LED
: JCI1
BIOS
79
1
2
CINTRU
GND
TPM : JTPM1 (
)
TPM (Trusted Platform Module)
()
1 2
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS : JBAT1
CMOS RAM
BIOS
CMOS RAM
OS
CMOS
1 2 3
1 2 3
Keep Data
1 2 3
Clear Data
:
CMOS 2-3
1-2 CMOS
PCI Express
PCI Express PCI Express
PCI
PCI
BIOS
80
PCI
IRQinterrupt request line IRQ
PCI IRQ PCI INT A#
INT D#
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
81
BIOS
POST (Power On Self Test)
<DEL>
Press DEL to enter SETUP
<DEL>
<RESET><Ctrl><Alt><Delete>
Integrated Peripherals
IDE, I/O
Power Management Setup
PNP/PCI Configurations
PCI
H/W Monitor
CPU
82
Frequency/Voltage Control
/
Load Optimized Defaults
BIOS
BIOS Setting Password
AMD CoolnQuiet
Cooln Quiet CPU
83
:
EMI [Disabled]
EMI [Enabled] EMI
Spread Spectrum EMI
EMI Spread Spectrum
[Disabled]
84
(Pb)
(Hg)
(Cd)
PCB
O SJ/T11363-2006
X SJ/T11363-2006
:
0.35% 0.4% 4%
-( 85%)
-
(pins)(microprocessors)
80~85%
(Flip Chippackages)