Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
PAGE NO.
FOREWORD
CARRIAGE OF MATERIALS
CHAPTER-R2
SITE CLEARANCE
CHAPTER-R3
CHAPTER-R4
CHAPTER-R5
CHAPTER-R6
CHAPTER-R7
CHAPTER-R8
2 to 5
6 to 13
14
15 to 17
18 - 20
21 - 22
23 - 27
28 - 29
30
31 - 35
CHAPTER-R9
SUPPLY OF MATERIAL
CHAPTER-R10
MAINTENANCE OF ROADS
CHAPTER-R11
HORTICULTURE
39
CHAPTER-R12
40
CHAPTER-R13
VIDEO PHOTOGRAPHY
41
CHAPTER-B1
FOUNDATIONS
42 - 46
CHAPTER-B2
SUB-STRUCTURE
47 - 49
CHAPTER-B3
SUPER-STRUCTURE
50 - 54
CHAPTER-B4
55 - 56
CHAPTER-B5
57 - 58
36
37 - 38
59 - 118
FOREWORD
1
The old schedule of rates for road & bridge works was prepared in 2008 and was inforce
w.e.f. 01/04/2008 with all upto date ammendments. Since then the rates of materials and
P.O.L. have been increased/decreased considerably. As such these schedules of rates
have been revised taking into consideration the current rates for labour, material and
P.O.L..
Ministry of Road Transport and Highways have revised the specification of road & bridge
works in August 2001 (IVth Revision). "Standard Data Book for Analysis of Rates" of
Ministry of Road Transport & Highway, has also been published by Indian Road
Congress recently. These specifications and SOR based on Standard Data Book are being
adopted generally by all the States of India and hence the New S.O.R. has been prepared
keeping in view the specifications of Road and Bridge works IVth Revision and on the
basis of the Standard Data Book of MORT&H.
New schedule of rates for Road and Bridge works is brought inforce with effect from
15 April 2009. This SOR shall be applicable for maintenance and construction of roads,
culverts and bridges for the entire Public Works Department in Madhya Pradesh except
for National Highway works. A common schedule for the entire MP PWD is issued to
facilitate easy preparation of estimates and their sanction and execution.
Some items have been modified in their nomenclature as per requirements. The
description of the items is kept according to the Standard Data Book and the
specifications (IVth Revision) of MORT&H published by the IRC. Few of the Items
which do not find place in the Standard Data Book for Analysis of Rates have also been
included in the new S.O.R. as these are required and provided in the old Schedule Of
Rates. This Schedule of Rates is not applicable for Building works.
Standard Tables given in the specifications are annexed with the S.O.R., so as to facilitate
easy reference to the specifications during execution. Important data regarding areas of
steel bars, weight of materials for bridge construction and conversion factors etc. are also
annexed.
I would like to commend Shri V.K.Bhugaonkar Chief Engineer (Planning), Shri Sanjay
Khande, Shri S.K. Kulkarni, Shri G.D.Gupta and Shri Ajit Ambare Executive
Engineer and Shri Rajiv Kuruvilla who have helped a lot in bringing out this schedule
of rates.
Suggestions, if any, towards further improvement to this Schedule of Rates for Road and
Bridge works will be highly welcomed.
(ER.SHAILENDRA SHUKLA)
ENGINEER-IN-CHIEF,
M.P. P.W.D. BHOPAL
Page 1
GENERAL NOTES
PART-1, ROAD WORKS
1)
(a)
(b)
(c)
(d)
"Specifications" would refer to the "Specifications for road and bridge works"
(4th Revision) published by the Indian roads Congress August'2001, on behalf
of the Government of India, Ministry of Road Transport & Highway (Roads
Wing).
"Clause" would refer to clauses of the specifications referred to in note (a)
above.
"Engineer-in-charge" would refer to the Executive Engineer of the division for
the time being.
"Table" would refer to the table of the aforesaid specifications.
2)
The rates of all items include element of setting out and carrying out the work in narrow
or part width of road, where directed.
3)
In the absence of any stipulation to the contrary, unit rates for different items of works
are for completing the works to the specifications I/c full compensation for all operations
detailed in the relevant sections of the specifications under "Rates". The rates are to be
considered as the full inclusive rate for the finished work covering all labour, material,
royalties, lease, rent, wastage, temporary work, plant, equipment, overhead charges
and profit, unless specified otherwise.
4)
5)
The rates include the element of hire and running charges of all types of plant,
machinery and equipment required to complete the work unless specified otherwise.
Royalty, octroi-duty and all other taxes are included in the rates.
6)
(i)
The rates include making arrangement of traffic as per clause No.112 except for
initial treatment to verge, shoulders and construction of diversion.
(ii)
The rates do not include the work of boring and trial pits, which are to be
measured and paid separately.
7)
The rates include all cleaning operations. The rates also include provision of coir rope
being used for premix carpet and surface dressings for providing supports to edges.
8)
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
NOTE:
I]
Only 60/70 grade bitumen will be used in all works but if in exceptional
circumstances 80/100 grade bitumen is required to be used, prior permission of
C.E. P.W.D. of the concerned Zone should be obtained, for which a reduction in
rate @Rs.2196/- per M.T. will be made on the theoritical consumption of the
quantity of bitumen. Tender premium shall also be accounted for.
II]
9)
The rates also include the element of testing of samples of various materials brought by
the contractor for use on the work as well as other tests for items of work as stipulated
in the specifications as per clause 903 and its sub-clauses of specifications for road and
bridge works of MORT&H (4th revision). Frequency of such tests to be carried out
must not be less than the prescribed frequencies. Copies from Registers containing
records of tests shall have to be presented alongwith running account bills. Actual
consumption of materials like bitumen, cement and steel be worked out in each running
bill before making payment. Register (Original) shall have to be submitted alongwith the
final bill. Tests shall have to be conducted for the contractor's material by his Engineers
under the supervision of the Engineer-in-charge or his authorised representatives.
Before making any payment it will be the responsibility of the officer making payment to
ensure that all tests as per prescribed frequencies have been carried out.
10)
The section 900 of the specification mentions "as required" against some of the tests.
To stave off disputes the following frequencies are specified :-
11)
12)
13)
For construction of reinforced earth retaining wall, back filling shall be paid separately as
per Chapter-3 "Earth work, erosion control and drainage"
14)
For WBM Grade-I and Grade-II broken stone can be used, for WBM Grade-III crushed
stone shall be used.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
15)
Metal to be used for all bituminous courses and cement concrete shall be crushed in
mechanical crushers.
16)
If any work is found to be sub-standard, but the Engineer-in-charge is of the opinion that
the same can be accepted at a reduced rate, then the Engineer-in-charge shall submit
proposals for the same, supported by an analysis i.e. justification of such reduction,
through a D.O. letter to the Superintending Engineer concerned, to obtain his approval
expeditiously (ordinarily within 15 days). The approved analysis along with orders of the
Superintending Engineer should be appended to the final bill of the contractor.
17)
The use of vibratory roller is essential for all the items where
compaction/consolidation is to be done with rollers unless specified otherwise.
18)
The surface regularity of the completed sub-grade, sub-base, base courses, widening of
surfaces and bituminous courses in the longitudinal and transverse directions shall be
within the tolerances indicated in the table 900-1 of the specifications. For checking,
specifications clause 902 shall apply. Failure to rectify the same will call for similar
action as provided for in note 14 above.
19)
The work of shoulders must preceed the work of sub-base and base courses and
succeed the bituminous courses and cement concrete pavement.
20)
21)
ever
a)
Rates of items would apply for work order/piece work system also.
b)
Rates payable for any work to be done departmentally on work order/piece work
may either be at-par or below rates in this SOR.
a)
Rates for transportation in Chapter No. 1 of "Carriage of Material" include :i) Loading and unloading into transport vehicle with incidental leads upto 100 M.
at each place and all lifts.
ii) Stacking at suitable places as directed by the Engineer-in-charge, the weights
of the container of any material shall be ignored.
22)
The measurements of rock excavation are to be done as per clause 301.8. However, if
the excavated rock is utilised by conversion into aggregtes also, then a deduction at the
rate of 45% shall be made from the stacked quantity of aggregates. To compute the
volumes of rock excavation size of the stacks should be as large as convenient.
23)
Rubble available from excavation of hard rock, shall be used for conversion into coarse
aggregates or for other constructions and shall be issued to the contractor at Rs.100 per
cubic meter of rock excavated.
24)
Rubble :- 1 Cubic meter of rubble for every cubic meter of excavated boulder
soling @Rs.115 per cubic meter of soling.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
b)
Coarse Aggregate :- 1.10 Cubic meter for every cubic meter of excavated WBM
@ Rs.120 per cubic meter of excavated WBM. (Excavated WBM should be
screened to segregate metal from moorum before re-use).
25)
For each compacted cubic meter of items of bituminous, base and surface courses the
approximate loose quantities required will be 1.4 cubic meter unless other wise
specified.
26)
For items of BUSG, surface dressing and seal coat type-A, the aggregates shall be
stacked at site, measured and recorded in M.B. prior to their use on work. No separate
payment shall be made for stacking and payment for these items shall be regulated as
per SOR items.
27)
Where laying of open graded premix carpet (OGPC) or seal coat Type-B with
machanical mixing is not feasible, use of Mixers are a MUST for open graded premix
carpet or seal coat Type 'B' using bitumen/emulsion. But this item can be used only with
prior approval of C.E.
28)
Rates for the items of semi-dense bituminous concrete, dense bituminous macadam
and bituminous concrete are based on the assumption that the bitumen at the rate of
5%, 4.25% and 5% respectively would be required. In case, lesser or more bitumen is
required as per the job mix formula. Difference of bitumen shall be paid or deducted as
per consumption of quantity of bitumen.
Only cement of required specifications at the rate of 2% by weight of total aggregate will
be used as filler for bituminous work wherever filler is to be provided. Lime will not be
used as filler.
The pavement camber or cross fall shall be provided as per provisions of IRC-73-1980.
29)
30)
31)
Bitumen & modified bitumen shall be obtained from reputed oil refinaries and emulsion
should be ISI marked only.
32)
In case of any contradiction in the provisions of the specifications and this schedule of
rates, the provisions of the later would take precedence.
Dismantling of utilities will be done under the supervision of concerned departments with
prior information to the users.
33)
34)
35)
36)
37)
38)
39)
40)
For narrow and restricted areas, plate compactors shall be used for compaction to
achieve the desired density.
The actual quantities of materials shall be as per job mix formula for bituminous works.
Latest I.R.C. Codes shall be followed.
Reflective sign board should not be installed on M.D.R. and on any other road having
traffic intensity less than 450 commercial vehicles per day without prior approval of the
Chief Engineer in writing.
The girth of trees shall be measured at 1.00 Metre (One Metre) above ground level.
Rates of site clearance include jungle clearance levelling and dressing.
All wood obtained from the tree shall be property of the government and shall be
deposited at P.W.D. store as per direction of Engineer-in-Charge.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
FOUNDATION
:
All works below ground level or low water level, whichever is higher but not above
soffit level shall be termed as foundation work.
ii)
Low water level shall be the average water level met with at the time of doing the
foundation work. The maximum and minimum water levels should be recorded by
the Assistant Engineer, just before starting the particular foundation and within a
reasonable time at the close of that foundation work, the average of these two levels
will be the L.W.L. for that foundation work. In case of major bridges such records will
be taken by the Executive Engineer.
2)
:
SUB-STRUCTURE
The part of the bridge structure below the a)Soffit level of the deck slab/beams and
or b)Springing level for arch spans, but above the ground level or L.W.L. which ever
is higher, shall be taken as sub structure of the bridge part. Complete RCC box
section will also be considered as sub-structure.
3)
:
SUPER-STRUCTURE
The work above (a)Soffit level for deck slabs/beams and (b)Springing level for arch
span, including kerbs, railing, expansion joints, beams, slabs etc. shall be termed as
super structure of the bridge part.
DEFINITIONS
:
Major Bridge :
Having total length between abutments at cap level 60 M.
and above.
4)
a)
b)
Medium Bridge :
c)
Culverts :
5)
i)
SPECIFICATIONS
:
The specifications of works shall be carried out as per 4th revision of "Specifications
for Road and Bridge works" (Ministry of Road Transport & Highway) - subject to such
changes as are incorporated in the wording of the items and notes below. The work
will be governed by the design considerations and specifications contained in I.R.C.
codes of practice for Road/Bridges issued upto the date of receipt of tender.
ii)
iii)
6)
a)
b)
The rates of both ordinary and controlled concrete of any mix include the cost of
preparing and testing concrete cubes as per specifications laid down.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
c)
All concrete shall be compacted to produce dense and homogeneous mass with the
assistance of vibrators unless otherwise permitted by the Engineer-in-Charge for
exceptional cases, such as concreting under water where, vibrators can not be used.
d)
Concrete poured under water shall be provided with 10% additional cement as per
"Specifications for Roads & Bridges works" Ministry of Road Transport & Highway
(4th Revision).
Finishing of concrete by plastering the surface shall not be done without obtaining
written permission from the Executive Engineer. No extra for plastering shall be
payable. Light touching up and rubbing the uneven surfaces by carborandum stone
shall be done within the specified rates.
e)
f)
g)
h)
i)
The grading, size, quality of coarse aggregates shall be strictly according to the
specifications for Road and Bridge works" (Ministry of Road Transport & Highway)
4th Revision and respective IRC Codes.
The size and quality of aggregate, mixing etc. for plain concrete or R.C.C. work
should be as given in "Specification for Road and Bridge works" of MORT&H (4th
Revision).
A mix leaner than M-15 may be used for non structural parts of the Bridge as
specified in Approved design/drawing.
The rates of concreting items include the cost of form work and centering.
j)
Super plasticizer admixtures should be used for the concrete work to improve the
workability with reduced water cement ratio and shall be provided as per clause
1705 of specifications.
7)
i)
STEEL
:
If the steel is brought by the contractor, the contractor shall be responsible for
ensuring the quality of steel and would be bound to conduct any or all tests at his
cost for ensuring its quality as per directions of the Engineer-in-Charge. The
theoritical consumption of steel shall be worked out at regular interval and shall be
verified with actual steel brought to the site.
ii)
iii)
iv)
If the steel is issued by the department the contractor shall be paid for labour
charges for steel on the quantity measured as per note above (i) Quantity as per
theoritical requirement plus 5% (five) shall be issued to the contractor and
deductions will be made for the extra quantity (upto 5%) at rates specified in the
N.I.T./Agreement if the steel is supplied by department. If the steel is brought by the
contractor, the contractor is held responsible for the quality of the steel. He should
use tested steel for which no extra payment is made for tests. If the steel is brought
by the contractor measurement shall be recorded as per clause 1607 of
specifications for Road and Bridges (MORT&H, 4th revision).
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
v)
Mild Steel, round bars, and deformed bars (left over after use in work) more than 3.0
M. in length will be accepted in return if the steel is supplied departmentally. For
steel left over with the contractor over and above theoritical consumption + 5% shall
be treated as un-authorised possession of steel and for this, the recovery should be
made at issue rate plus 10% or prevailing market rate, which ever is higher.
8)
i)
CEMENT
:
If the cement is brought by the contractor, the contractor shall be responsible for
ensuring the quality of cement and would be bound to conduct any of all tests at his
cost for ensuring its quality as per directions of the Engineer-in-Charge. The
theoritical consumption of cement shall be worked out at regular interval and shall be
verified with actual cement brought to the site
ii)
The cement, if supplied by department at issue rate to the contractor shall not be
more than the theoritical consumption plus 2%. If cement more than this is issued,
recovery for the extra quantities shall be made at issue rate plus 10% or prevailing
market rate which ever is higher.
iii)
The theoritical consumption of cement should be worked out after including all
contingent works I.e., cement godowns, casting plat forms, bed blocks etc. which are
necessary for the work in the opinion of Engineer-in-Charge and have actually been
constructed, but shall not include items, which are executed for setting right the
imperfections in work.
9)
i)
MASONRY WORK
:
All the stone masonry work shall be strictly as per detailed specifications given in
"Specification for Road & Bridge works" of MORT&H (4th Revision).
In place of stone headers, precast or cast-in-situ concrete headers may be permitted
with following condition :
ii)
a) If the cement is supplied departmentally and the cost of cement is recoverable from
the contractor due allowance for the actual quantity of cement consumed in the use
of cement concrete headers shall be permitted in cement consumption statement but
no extra payment for providing cement concrete, headers shall be payable.
iii)
Generally for all stone masonry subjected to exposure of water flow (e.g. piers,
abutments, returns etc.) C.R. Masonry first sort shall be used unless otherwise
provided in the approved drawing.
iv)
In case where width of stone masonry is more than one meter, the central portion of
stone masonry (Hearting) shall be done with uncoursed randum rubble masonry.
Payment for the C.R. Masonry will be limited to 1/2 meter width on either faces and
the balance will be paid as uncoursed Randum Rubble Masonry.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
10)
i)
ii)
12)
:
13)
:
DISMANTLING
The rates include the complete cost of dismantling and shifting away the dismentled
material to place at site of work as directed by Engineer-in-Charge and also the rates
include the serviceable dismentled material to be properly stacked at river bank at a
location directed by the Engineer-in-Charge.
14)
15)
The rate includes the element of hire & operational charges of all types of plants,
machinery and equipment required to complete the work unless specified otherwise.
16)
17)
The rates do not include the work of trial pits, which are to be measured and paid
separately.
18)
The contractor is bound to install at the site of work a test laboratory capable of
conducting all specified field tests as per direction of Engineer-in-Charge and the
specified tests of material would be conducted in the presence of department's
supervisory staff.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
10
19)
Detailed measurements for steel and concrete for items of R.C.C. approach slab,
R.C.C. Railing and R.C.C. wearing coat shall also be recorded in M.B. However the
payment shall be regulated as per the item and rates given in the S.O.R.
20)
The specifications mentioned under section 2900 shall also be applicable to items of
Hume Pipe Culverts in addition to those given in the items.
21)
The measurement of rock excavation are to be done as per clause specified in the
Book "Specification of Road and Bridge works" of MORT&H. All serviceable rock
excavated shall be issued to the contractor at the rate of Rs.100/- per Cum.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
11
CHAPTER - B1
FOUNDATION
NOTES :1)
The excavation shall be paid as per the area of foundation concrete block, multiplied
by the depth below average ground level at the location of foundation. The rates
include the extra quantity of excavation required for providing the excavation in steps
or slope as per direction of Engineer-in-Charge.
2)
3)
4)
5)
6)
7)
The rates of well sinking include the charges of labour, plant, cost of P.O.L. and
other materials and accessories. The rates also include the cost of diversion of
channel, making of island, if required to be done for laying the cutting edge, kerb and
steining. the permissible tilt and shift in well in its final position shall be as per IRC78-1983. The rates include the cost of rectification of tilt and shift in excess of
permissible limit. No extra over these rates are payable for sinking of well.
8)
For the purpose of the computation of the volume in well sinking, the cubic content
of well shall be measured by the portion contained in outer diameter of well steining.
Projection of R.C.C. kerb, if any shall not be measured.
9)
the rates of concreting in all types of foundation include also the cost of form work,
staging etc. complete.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
12
CHAPTER - B2
SUB-STRUCTURE
NOTES :1)
The rates of bearing are inclusive of the charges required for testing of bearing,
procurement, transport, if required greasing while storing and at the time of fixing etc.
all complete.
2)
The use of A.C. Pipes for weep holes is permitted only in PCC/RCC/Brick masonary
sub-structure. In stone masonry inbuilt weep holes of size 80mm x 150mm shall be
constructed and no extra for this work is payable. No deduction for the recess or for
pipes due to weep holes shall be made in the measurement of stone/brick
masonary, PCC and RCC.
The rates of concreting in all items include the cost of form work and staging.
3)
4)
5)
For elastomeric bearing pads the concrete surface shall be levelled such that the
variation is not more than 1.5mm from the straight edge placed in any direction
across the area.
The bearings should be procured only from those manufactures who have not been
disqualified by MORT&H.
6)
Only finished weight of bearings as brought to the site and fixed in position shall be
taken into account for measurement.
7)
The height of filling above the top of hume pipe culverts shall not be less than
600mm.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
13
CHAPTER - B3
SUPER STRUCTURE
NOTES :The rates of concreting include the cost of form work, centering staging etc.
1)
complete.
For super structure only steel form work will be accepted. The thickness of steel
2)
plate shall not be less than 3 mm. The form work shall be adequately stiffened by
brackets and angles not more than 15 cm. apart in such a manner that it is free from
distoration during handling and vibration of concrete. No extra for form work shall be
payable.
3)
4)
Centering made up of steel trusses below soffit shall not be supported in recess
made in sub-structure. The contractor may provide steel trusses supported on
suitably designed bracket, anchored to the pier/pier-cap. Providing safe centering
shall be solely contractor's responsibility. The contractor shall remove all bolts,
anchors protruding beyond the pier/pier-cap after removal of centering. No extra for
centering shall be payable.
Contractor shall have the option to adopt launching of super-structure but in such
cases prior permission of the department be obtained by getting launching
arrangement initially approved. No deduction in the rate of concrete would be done
nor any extra would be paid in case the launching is resorted to.
5)
The rate of prestressing of H.T. steel is complete rate including hire and running
expenses of plant and machinaries, labour involved in stressing operations,
anchorages and ducts or sheathing etc., complete including grouting.
6)
7)
The payment of railing includes the construction of required intermediate posts and
end posts. The length of railing for payment purposes on each side separately, be
measured from the outer edges of end posts.
8)
New type expansion joints may be obtained from prequalified suppliers by MORT&H
and the firm will have to give warranty of 10 years of trouble free performance.
9)
For hume pipe culverts, hume pipes must be procured through MP LUN and pipes
shall be ISI marked or DGS&D certified only and a certificate should invariably be
produced to the satisfaction of Engineer-in-Charge before getting the pipes fixed at
site. E.E. will see that the pipe are strictly as per specifications and IS Codes.
SOR for Road Bridge works in Public Works Deptt. Madhya Pradesh
14
CHAPTER-R1
CARRIAGE OF MATERIALS
Item
No.
1.1
i)
ii)
iii)
iv)
v)
vi)
vii)
viii)
ix)
1.2
a)
b)
c)
d)
e)
f)
g)
h)
I)
j)
k)
1.3
i)
ii)
iii)
1.4
a)
b)
c)
d)
Descriptions
(Volume to be computed as per provisions in clause 514)
Transportation of metal
For a lead upto 1 Km.
For a lead upto 2 Km.
For a lead upto 3 Km.
For a lead upto 4 Km.
For a lead upto 5 Km.
Beyond 5 Kms. and upto 10 Kms. (Add for every 1 Km)
Beyond 10 Kms. and upto 20 Kms. (Add for every 1 Km)
Beyond 20 Kms. and upto 50 Kms. (Add for every 1 Km)
Beyond 50 Kms. (Add for every 1 Km)
Transportation of different other material
Unit
Rate (Rs.)
cum
cum
cum
cum
cum
cum
cum
cum
cum
60.00
66.00
69.00
72.00
77.00
3.60
3.00
2.70
2.20
CHAPTER-R2
SITE CLEARANCE
Item
No.
2.1
i)
ii)
iii)
iv)
2.2
a)
b)
2.3
(i)
a)
b)
c)
(ii)
a)
b)
c)
d)
(iii)
a)
b)
c)
d)
e)
f)
(iv)
(v)
a)
b)
Descriptions
Cutting of trees, including cutting of trunks, branches and removal of
stumps, roots, stacking of serviceable material with all lifts and up to a
lead of 1000 mtrs and earth filling in the depression/pit and as per
relevant clauses of section-200 for
Girth from 300 mm to 600 mm
Girth beyond 600 mm to 900 mm
Girth beyond 900 mm to 1800 mm
Girth above 1800 mm
Clearing and grubbing road landincluding uprooting rank
vegetation, grass, bushes, shrubs, saplings and trees girth up to 300
mm, removal of stumps of trees cut earlier and disposal of
unserviceable materials and stacking of serviceable material to be used
or auctioned up to a lead of 1000 metres including removal and
disposal of top organic soil not exceeding 150 mm in thickness if
required and as per relevant clauses of section-200.
In area of light jungle
In area of thorny jungle
Dismantling of existing structureslike culverts, bridges, retaining
walls and other structure comprising of masonry, cement concrete,
wood work, steel work, including T&P and scaffolding wherever
necessary, sorting the dismantled material, disposal of unserviceable
material and stacking the serviceable material with all lifts and lead
upto 1000 metres and as per relevant clauses of section-200 in
Concrete
Lime Concrete, cement concrete grade M-10 and below
Cement Concrete Grade M-15 & M-20
Prestressed / Reinforced cement concrete grade M-20 & above
Tile work/brick masonry
In lime mortar
In cement mortar
In mud mortar
Dry brick pitching or brick soling
Stone Masonry
Rubble stone masonry in lime mortar
Rubble stone masonry in cement mortar.
Rubble Stone Masonry in mud mortar.
Dry rubble masonry
Stone pitching/ dry stone spalls.
Boulders laid in wire crates including opening of crates and stacking
dismantled materials.
Steel work in all types of sections upto a height of 5 m above plinth
level excluding cutting of rivet Including dismembering
Scraping of bricks dismantled from brick work including stacking.
In lime/Cement mortar
In mud mortar
Unit
Rate (Rs.)
each
each
each
each
105.00
205.00
373.00
684.00
hectare
hectare
19095.00
25663.00
cum
cum
cum
166.00
191.00
477.00
cum
cum
cum
cum
116.00
141.00
106.00
101.00
cum
cum
cum
cum
cum
126.00
141.00
116.00
111.00
106.00
cum
116.00
tonne
684.00
1000 No.
1000 No.
438.00
157.00
Item
No.
(vi)
a)
b)
(vii)
Descriptions
(viii)
a)
b)
c)
2.4
a)
b)
2.5
2.6
2.7
2.8
a)
b)
c)
2.9
2.10
Unit
Rate (Rs.)
cum
cum
sqm
176.00
37.00
6.00
Removing all type of hume pipes and stacking within a lead upto 1000
metres including earthwork and dismantling of masonry works around
pipes.
Up to 600 mm dia
Above 600 mm to 900 mm dia
Above 900 mm dia
metre
metre
metre
65.00
88.00
151.00
cum
cum
304.00
226.00
cum
871.00
metre
34.00
metre
8.00
each
each
each
156.00
93.00
19.00
metre
22.00
metre
56.00
Item
No.
2.11
2.12
Descriptions
Removal of cement concrete pipe of sewer gutterupto 1500 mm dia
under the supervision of concerned department including disposal with
all lifts and up to a lead of 1000 metres and stacking of serviceable and
unserviceable material separately but excluding earth excavation and
dismantling of masonry works
Removal of telephone / Electric polesincluding excavation and
dismantling of foundation concrete and lines under the supervision of
concerned department, disposal with all lifts and up to a lead of 1000
metres and stacking the serviceable and unserviceable material
separately.
Unit
Rate (Rs.)
metre
69.00
each
77.00
CHAPTER-R3
EARTH WORK, EROSION CONTROL AND DRAINAGE
Item
No.
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Descriptions
Excavation for roadway in soil including loading in truck for carrying
of cut earth to embankment site with all lifts and lead upto1000 metres
and as per relevant clauses of section-300
Excavation in ordinary rock including loading in a truck and
carrying of excavated material to embankment site with in all lifts and
leads upto 1000 metres and as per relevant clauses of section-300
Excavation for roadway in ordinary rock by deploying a dozer
, 80
HP including cutting and pushing the cut earth to site of embankment
upto a distance of 100 metres ( average lead 50 metres ), trimming
bottom and side slopes in accordance with the requirements of lines,
grades and cross sections as per relevant clauses of section-300 of
specifications.
Excavation for roadway in hard rock (requiring blasting) by
drilling, blasting and breaking, trimming of bottom and side slopes in
accordance with requirements of lines, grades and cross sections,
loading and disposal of cut road with in all lifts and leads upto 1000
metres and as per relevant clauses of section-300
Excavation for roadway in hard rock (blasting prohibited) with
rock breakers including breaking rock, loading in tippers and disposal
within all lifts and lead upto 1000 metres, trimming bottom and side
slopes in accordance with requirements of lines, grades and cross
sections and as per relevant clauses of section-300
Excavation for roadway in hard rock with controlled blasting by
drilling, blasting and breaking, trimming of bottom and side slopes in
accordance with requirements of lines, grades and cross sections,
loading and disposal of cut road with in all lifts and leads upto 1000
metres and as per relevant clauses of section-300
Excavation for roadway in marshy soil with hydraulic excavator
including cutting and loading in tippers and disposal with in all lifts an
lead upto 1000 metres, trimming of bottom and side slopes in
accordance with requirements of lines, grades and cross sections and as
per relevant clauses of section-300.
Scarifying the existing granular road surfaceto a depth of 50 mm
and disposal of scarified material within all lifts and leads upto 1000
metres.
Scarifying the existing granular road surfaceto a depth of 50 mm
and disposal of scarified material within all lifts and leads upto 1000
metres.
Scarifying the existing bituminous road surface by mechanical
means to a depth of 50 mm and disposal of scarified material with in
all lifts and lead upto 1000 metres.
Unit
Rate (Rs.)
cum
69.00
cum
95.00
cum
120.00
cum
140.00
cum
503.00
cum
146.00
cum
40.00
sqm
15.50
sqm
11.50
sqm
120.00
Item
No.
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
Descriptions
Construction of embankment/subgradewith approved
material/selected soil having CBR >5 (Unless specified othewise in the
cotract) obtained from road side cutting excavation of drain and
foundation of other structure i/c all lifts & leads upto 1000 M. i/c
grading to required slope & camber and compacting using vibratory
roller of 80 to 100 kN static weight to meet requirement of Table
300.1, 300.2 and as per relevant clause of section 300.
Construction of embankment/subgradewith approved
material/selected soil having CBR >5 (Unless specified othewise in the
cotract) obtained from excavation of borrow pits i/c all lifts & leads
upto 250 M. i/c grading to required slope & camber and compacting
using vibratory roller of 80 to 100 kN static weight to meet
requirement of Table 300.1, 300.2 and as per relevant clause of section
300.
Back filling behind the facing elementin reinforced earth walls with
approved material/selected soil having CBR >12 (Unless specified
othewise in the cotract) obtained from excavation of borrow pits i/c all
lifts & leads i/c grading to required slope & camber and compacting
using vibratory roller of 80 to 100 kN static weight to meet
requirement of clause 3103.
Construction of embankment/subgradewith approved
material/selected soil having CBR >5 (Unless specified otherwise in th
contract) obtained from excavation of borrow pits i/c all lifts & leads
i/c grading to required slope & camber and compacting using vibratory
roller of 80 to 100 kN static weight to meet requirement of Table
300.1, 300.2 and as per relevant clause of section 300.
Construction of Hard Shoulder withapproved material/selected soil
having CBR >12 i/c excavation all lifts & leads i/c grading to
required slope & camber of 4% and compacting using vibratory roller
of 80 to 100 kN static weight to meet requirement as per relevant
clause of 400.
Deduct for item No.3.9, 3.10, 3.11 and 3.12 if vibratory roller / mortar
grader is not used with prior written approval of S.E.:
i) If static roller is used in place of vibratory roller.
ii) If mortar grader is not used.
Construction of unlined surface drainsof average cross sectional
area 0.40 sqm in soil to specified lines, grades, levels and dimensions t
the requirement of clause 301 and 309. Excavated material to be used
in embankment within a lead of 50 metres and as per relevant clauses
of section-300.
Construction of aggregate sub surface drain300 mm width x 450
mm depth with aggregates conforming to table 300-4, excavated
material to be utilised in roadway and as per relevant clauses of section
300.
Unit
Rate (Rs.)
cum
54.00
cum
137.00
cum
188.00
cum
134.00
cum
176.00
cum
cum
30.00
30.00
metre
25.00
metre
82.00
Item
No.
3.18
a)
b)
c)
Descriptions
Construction of embankment with fly ashconforming to table 1 of
IRC: SP: 58 - 2001 obtained from coal or lignite burning thermal
power stations as waste material, spread and compacted in layer of
200mm thickness each at OMC, all as specified in IRC: SP: 58-2001
and as per approved plans and as per relevant clauses of section-300
with lead of fly ash.
Upto 25 Kms.
Beyond 25 Kms. and upto 50 Kms.
Beyond 50 Kms. and upto 100 Kms.
Unit
Rate (Rs.)
cum
cum
cum
180.00
236.00
276.00
CHAPTER-R4
SUB-BASES, BASES ( NON- BITUMINOUS) AND SHOULDERS
Item
No.
4.1
i)
ii)
iii)
4.2
4.3
(i)
a)
b)
(ii)
a)
b)
c)
(iii)
a)
b)
4.4
4.5
Descriptions
Construction of granular sub-baseby providing coarse graded
material, spreading in uniform layers with on prepared surface, mixing
by mix in place method at OMC, and compacting with vibratory roller
to achieve the desired density, complete in all respect and as per
relevant clauses of section-400
for grading- I Material
for grading- II Material
for grading-III Material
Laying and spreading available soil in the subgrade on a prepared
surface, pulverising, mixing the spread soil in place with rotavator with
3 % slaked lime having minimum content of 70% of CaO, grading with
motor grader and compacting with the road roller at OMC to the
desired density to form a layer of improved sub grade complete and as
per relevant clauses of section-400. (Lime stabilisation for improving
sub-grade)
Providing, laying, spreading and compacting stone aggregates of
specific sizes to water bound macadamspecification including
spreading in uniform thickness, hand packing, rolling with vibratory
roller 8-10 tonnes in stages to proper grade and camber, applying and
brooming requisite type of screening/ binding materials to fill up the
interstices of coarse aggregate, watering and compacting to the
required density and as per relevant clauses of section-400
Grading- I
Using Screening Crushable type
Using Screening Type-A (13.2mm Agg.)
Grading- II
Using Screening Crushable type
Using Screening Type-A (13.2mm Agg.)
Using Screening Type-B (11.2mm Agg.)
Grading- III
Using Screening Crushable type
Using Screening Type-B (11.2mm Agg.)
Deduction for item No.4.1, 4.2 & 4.3 if vibratory roller / mortar grader
is not used with prior written approval by S.E. :
i) If static roller is used in place of vibratory roller.
ii) If mortar grader is not used.
Providing, laying, spreading and compacting graded stone aggregate to
wet mix macadamspecification including premixing the Material with
water at OMC in mechanical mix plant carriage of mixed Material by
tipper to site, laying in uniform layers with paver in sub- base / base
course on well prepared surface and compacting with vibratory roller
to achieve the desired density and as per relevant clauses of section400.
Unit
Rate (Rs.)
cum
cum
cum
505.00
510.00
519.00
cum
352.00
cum
cum
673.00
765.00
cum
cum
cum
715.00
750.00
792.00
cum
cum
700.00
778.00
cum
cum
50.00
50.00
cum
659.00
Item
No.
4.6
4.7
4.8
a)
i)
ii)
b)
i)
ii)
4.9
a)
b)
c)
Descriptions
Construction of Median and Islandabove road level with approved
material deposited at site from roadway cutting and excavation for
drain and foundation of other structures or borrow pits, spread, graded
and uncompacted including excavation and lead upto 1000 M. and as
per relevant clauses of section-400
Construction of medianand Island above road level with approved
material brought from borrow pits including excavation and all leads,
spread, sloped and compacted and as per relevant clauses of section400.
Crusher Run Macadam Base(Providing crushed stone aggregate,
depositing on a prepared surface by hauling vehicles, spreading and
mixing with a motor grader, watering and compacting with a vibratory
roller to clause 410 to form a layer of sub-base/Base)
By Mix in Place Method
For 53 mm maximum size
For 45 mm maximum size
By Mixing Plant :
For 53 mm maximum size
For 45 mm maximum size
Construction of Sub-base using lime - fly ashadmixture with 80%
granular soil, free from organic matter/ deleterious material or clayey
silts and low plasticity clays having PI between 5 and 20 and liquid
limit less than 25, 16% flyash and 4% commercial dry lime, slaked at
site or pre-slaked with CaO content not less than 50%, fly ash to
conform to gradation as per clause 4.3 of IRC: 88-1984, the minimum
un-confined compressive strength and CBR value after 28 days curing
and 4 days soaking to be 7.5kg/sq, cm and 25% respectively, all as
specified in IRC: 88 and as per relevant clauses of section-400 with
lead of fly ash.
Upto 25 Kms.
Beyond 25 Kms. and upto 50 Kms.
Beyond 50 Kms. and upto 100 Kms.
Unit
Rate (Rs.)
cum
56.00
cum
97.00
cum
cum
685.00
719.00
cum
cum
783.00
819.00
cum
cum
cum
421.00
443.00
475.00
CHAPTER-R5
BASES AND SURFACE COURSES (BITUMINOUS)
Item
No.
5.1
5.2
i)
ii)
iii)
iv)
5.3
i)
ii)
5.4
5.5
Descriptions
Providing and applying primer coatwith bitumen emulsion on
prepared surface of granular Base including clearing of road surface
and spraying primer at the rate of 0.75 kg/sqm using mechanical means
and as per relevant clauses of section-500
Providing and applying tack coat with bitumen emulsionusing
emulsion pressure distributor on the prepared bituminous/granular
surface cleaned with mechanical broom and as per relevant clauses of
section-500.
@ 0.25 kg per sqm (normal bituminous surfaces)
@ 0.30 kg per sqm (dry & hungry bituminous surfaces/granular
surfaces treated with primer)
@ 0.40 kg per sqm (Non-bituminous surfaces) granular base not
primed.
@ 0.35 kg per sqm (Non-bituminous surfaces) cement concrete
pavement.
Providing and laying bituminous macadamwith hot mix plant using
crushed aggregates of specified grading premixed with bituminous
binder, transported to site, laid over a previously prepared surface with
mechanical paver finisher to the required grade, level and alignment
and rolled as per clauses 501.6 and 501.7 to achieve the desired
compaction complete in all respects and as per relevant clauses of
section-500.
for Grading I ( 80-100mm thickness ) bitumen content 3.25%
for Grading II( 50-75mm thickness ) bitumen content 3.4%
Providing and laying levelling course/profile corrective course with
bituminous macadamwith hot mix plant using crushed aggregates of
grading-1 premixed with bituminous binder @ 3.1%, transported to
site, laid over a previously prepared surface with mechanical paver
finisher to the required grade, level and alignment and rolled as per
clauses 501.6 and 501.7 to achieve the desired compaction complete in
all respects and as per relevant clauses of section-500.
Providing, laying and rolling of built-up-spray groutlayer over
prepared base consisting of a two layer composite construction of
compacted crushed coarse aggregates. key stone chips spreader may be
used with application of bituminous binder after each layer, and with
key aggregates placed on top of the second layer to serve as a Base
conforming to the line, grades and cross-section specified, the
compacted layer thickness being 75 mm and as per relevant clauses of
section-500.
Unit
Rate (Rs.)
sqm
22.00
sqm
8.00
sqm
10.00
sqm
12.00
sqm
11.00
cum
cum
3598.00
3702.00
cum
3490.00
sqm
158.00
10
Item
No.
5.6
i)
ii)
5.7
i)
ii)
iii)
iv)
v)
vi)
5.8
i)
ii)
iii)
iv)
v)
vi)
5.9
i)
ii)
Descriptions
Providing and laying dense bituminous macadamwith hot mix plant
batch using crushed aggregates of specified grading, premixed with
bituminous binder, transporting the hot mix to work site, laying with
mechanical paver finisher to the required grade, level and alignment,
rolling with smooth wheeled, vibratory and tandem rollers to achieve
the desired compaction complete in all respects and as per relevant
clauses of section-500. (Only cement will be used as filler
for Grading I ( 80-100mm thickness )
for Grading II( 50-75mm thickness )
Providing and laying semi dense bituminous concretewith hot mix
plant using crushed aggregates of specified grading, premixed with
bituminous binder, transporting the hot mix to work site, laying with
mechanical paver finisher to the required grade, level and alignment,
rolling with smooth wheeled, vibratory and tandem rollers to achieve
the desired compaction in all respects and as per relevant clauses of
section-500. (Only cement will be used as filler).
for Grading I ( 35-40 mm thickness ) with 60/70 butumen
for Grading I ( 35-40 mm thickness ) with CRMB-60
for Grading I ( 35-40 mm thickness ) with PMB-40
for Grading II (25-30 mm thickness ) with 60/70 bitumen
for Grading II ( 25-30 mm thickness ) with CRMB-60
for Grading II ( 25-30 mm thickness ) with PMB-40
Providing and laying bituminous concretewith hot mix plant using
crushed aggregates of specified grading, premixed with bituminous
binder, transporting the hot mix to work site, laying with a mechanical
paver finisher to the required grade, level and alignment, rolling with
smooth wheeled, vibratory and tandem rollers to achieve the desired
compaction in all respects and as per relevant clauses of section-500.
(Only cement will be used as filler).
for Grading I ( 50-65 mm thickness ) with 60/70 bitumen
for Grading I ( 50-65 mm thickness ) with CRMB-60
for Grading I ( 50-65 mm thickness ) with PMB-40
for Grading II ( 30-45 mm thickness ) with 60/70 bitumen
for Grading II ( 30-45 mm thickness ) with CRMB-60
for Grading II ( 30-45 mm thickness ) with PMB-40
Providing and laying surface dressingin single coat using crushed
stone aggregates of specified size on a layer of bituminous binder laid
on prepared surface and rolling with 8-10 tonne smooth wheeled steel
roller and as per relevant clauses of section-500
with 19 mm nominal chipping size & bitumen @1.2kg per sqm.
with 13 mm nominal chipping size & bitumen @ 1.0 kg per sqm.
Unit
Rate (Rs.)
cum
cum
4633.00
4654.00
cum
cum
cum
cum
cum
cum
4841.00
4878.00
4851.00
5200.00
5269.00
5723.00
cum
cum
cum
cum
cum
cum
5329.00
5361.00
5859.00
5327.00
5360.00
5857.00
sqm
sqm
51.00
42.00
11
Item
No.
5.10
5.11
5.12
Note :
5.13
i)
ii)
iii)
5.14
i)
ii)
Descriptions
Providing, laying and rolling of open - graded premix surfacingof
20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using
60/70 grade bitumen to required line, grade and level to serve as
wearing course on a previously prepared base, including mixing in hot
mix plant, laying with paver finisher and rolling with a smooth wheeled
roller 8-10 tonne capacity, finished to required level and grades
excluding primer and tack coat and as per relevant clauses of section500.
Providing, laying and rolling of open - graded premix surfacingof
20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either
using cationic bitumen emulsion to required line, grade and level to
serve as wearing course on a previously prepared base, including
mixing in a cold mix plant or concrete mixer laying with paver finisher
and rolling with a smooth wheeled roller 8-10 tonne capacity, finished
to required level and grades excluding primer and tack coat and as per
relevant clauses of section-500
Providing, laying and rolling of open - graded premix surfacingof
20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using
60/70 grade bitumen to required line, grade and level to serve as
wearing course on a previously prepared base, including mixing in a
concrete mixer or cold mix plant laying with paver finisher and rolling
with a smooth wheeled roller 8-10 tonne capacity, finished to required
level and grades excluding primer and tack coat and as per relevant
clauses of section-500.
This item can be executed only with prior approval of the Chief
Providing, laying and rolling of close-graded premix surfacing /
mixed seal surfacingmaterial of 20 mm thickness composed of 11.2
mm to 0.09 mm (Type-a) or 13.2 mm to 0.09 mm (Type-b) aggregates
using penetration grade bitumen to the required line, grade and level to
serve as wearing course on a previously prepared base, including
mixing in a suitable plant, laying and rolling with a Smooth wheeled
roller 8-10 tonne capacity, and finishing to required level and grade and
as per relevant clauses of section-500
Type-A or Type-B aggregate
with 60/70 butumen
with CRBM-60
with PMB-40
Providing and laying seal coatsealing the voids in a bituminous
surface laid to the specified levels, grade and cross fall using Type A
and B seal coats and as per relevant clauses of section-500 with
bitumen.
Type A (Liquid Seal Coat)
Type B (Premixed Seal Coat with hot mix plant & paver finisher)
Unit
Rate (Rs.)
sqm
79.00
sqm
60.00
sqm
69.00
sqm
sqm
sqm
102.00
109.00
118.00
sqm
38.00
sqm
29.00
12
Item
No.
5.15
i)
Note :
5.16
5.17
i)
ii)
iii)
5.18
i)
ii)
Descriptions
Providing and laying seal coatsealing the voids in a bituminous
surface laid to the specified levels, grade and cross fall using Type-B
seal coats and as per relevant clauses of section-500 with bitumen
without hot mix plant/paver finisher
This item can be executed only with prior approval of the Chief
Engineer.
Providing and laying 25 mm thickmastic asphalt wearing course with
30/40 grade bitumen meeting the requirements given in table 500-29,
prepared by using mastic cooker and laid to required level and slope
after cleaning the surface, including providing antiskid surface with
bitumen precoated fine-grained hard stone chipping of 13.2 mm
nominal size at the rate of 0.005cum per 10 sqm and at an approximate
spacing of 10 cm center to center in both directions, pressed into
surface when the temperature of surfaces not less than 1000C,
protruding 1 mm to 4 mm over mastic surface complete in all respect
and as per relevant clauses of section-500
Providing and laying slurry seal consisting of a mixture of fine
aggregates, portland cement filler, bituminous emulsion and water on a
road surface including cleaning of surface, mixing of slurry seal in a
suitable mobile plant, laying and compacting to provide even riding
surface and as per relevant clauses of section-500
5 mm thickness
3 mm thickness
1.5 mm thickness
Crack Prevention Courses
Stress Absorbing Membrane (SAM) crack width less than 6 mm
(Providing and laying of a stress absorbing membrane over a cracked
road surface, with crack width below 6 mm after cleaning with a
mechanical broom, using modified binder complying with clause 521
sprayed at the rate of 9 kg per 10 sqm and spreading 5.6 mm crushed
stone aggregates @ 0.11 cum per 10 sqm with hydraulic chip
spreader, sweeping the surface for uniform spread of aggregates and
surface finished to conform to clause 902.)
Stress Absorbing Membrane (SAM) with crack width 6 mm to 9
mm (Providing and laying of a stress absorbing membrane over a
cracked road surface, with crack width 6 to 9 mm after cleaning with
a mechanical broom, using modified binder complying with clause
521, sprayed at the rate of 11 kg per 10 sqm and spreading 11.2 mm
crushed stone aggregates @ 0.12 cum per 10 sqm, sweeping the
surface for uniform spread of aggregates and surface finished to
conform to clause 902.)
Unit
Rate (Rs.)
sqm
20.00
sqm
422.00
sqm
sqm
sqm
39.00
27.00
16.00
sqm
38.00
sqm
47.00
13
Item
No.
iii)
iv)
5.19
i)
ii)
5.20
NOTE
5.21
NOTE
Descriptions
Stress Absorbing Membrane (SAM) crack width above 9 mm and
cracked area above 50 % (Providing and laying a single coat of a
stress absorbing membrane over a cracked road surface, with crack
width above 9 mm and cracked area above 50 % after cleaning with a
mechanical broom, using modified binder complying with clause 521
sprayed at the rate of 15 kg per 10 sqm and spreading 11.2 mm
crushed stone aggregates @ 0.12 cum per 10 sqm, sweeping the
surface for uniform spread of aggregates and surface finished to
conform to clause 902.)
Case - IV : Bitumen Impregnated Geotextile(Providing and laying
a bitumen impregnated geotextile layer after cleaning the road
surface, geotextile conforming to requirements of clause 704.3, laid
over a tack coat with 1.05 kg per sqm of paving grade bitumen 80 100 penetration and constructed to the requirement of clause 704.4.5)
labour only for Laying and rolling of Bituminous coursesi/c primer
and tack coat (excluding cost of bitumen & metal) with a smooth
wheeled roller 8-10 tonne capacity i/c hire charges & running expenses
finished to required level and grades and as per relevant clauses of
section-500.
20mm Open Graded Premix Carpet
75mm Built-up Spray Grout
Providing, laying and rolling of open - graded premix surfacingof 20
mm thickness composed of 13.2 mm to 5.6 mm aggregates using 60/70
grade bitumen, including PCC as a integral part of it, to required line,
grade and level to serve as wearing course on a previously prepared
base, including mixing in hot mix plant, laying with paver finisher and
rolling with a smooth wheeled roller 8-10 tonne capacity, finished to
required level and grades excluding primer and tack coat and as per
relevant clauses of section-500.
This item shall be executed only after prior approval of the Chief
Engineer.
Providing, laying and rolling of close-graded premix surfacing / mixed
seal surfacing material of 20 mm thickness composed of 13.2 mm to
0.09 mm (Type-b) aggregates using penetration grade bitumen,
including PCC as a integral part of it, to the required line, grade and
level to serve as wearing course on a previously prepared base,
including mixing in a suitable plant, laying and rolling with a Smooth
wheeled roller 8-10 tonne capacity, and finishing to required level and
grade and as per relevant clauses of section-500.
Type-B aggregate
with 60/70 butumen
This item shall be executed only after prior approval of the Chief
Engineer.
Unit
Rate (Rs.)
sqm
62.00
sqm
231.00
sqm
sqm
12.50
15.50
Cum.
3920.00
Cum.
4900.00
14
CHAPTER-R6
CEMENT CONCRETE PAVEMENTS
Item
No.
6.1
6.2
6.3
6.4
6.5
6.6
Descriptions
Construction of dry leancement concrete Sub- base over a prepared
sub-grade with coarse and fine aggregate conforming to IS: 383, the
size of coarse aggregate not exceeding 25 mm, aggregate cement ratio
not to exceed 15:1, aggregate gradation after blending to be as per table
600-1, cement content not to be less than 150 kg/ cum, optimum
moisture content to be determined during trial length construction,
concrete strength not to be less than 10 Mpa at 7 days, mixed in a
batching plant, transported to site, laid with paver with electronic
sensor, compacting with 8-10 tonnes vibratory roller, finishing and
curing and as per relevant clauses of section-600
Deduct from Item No.6.1 above if paver with electronic sensor,
vibratory roller are not used and laying, compaction is done by any
other method. .
Construction of dowel jointed, plaincement concrete pavement in M40 grade concrete over a prepared sub base with 43 or higher grade
cement, maximum size of coarse aggregate not exceeding 25 mm,
mixed in a batching and mixing plant as per approved mix design,
transported to site, laid with a fixed form or slip form paver with
electronic sensor, spread, compacted and finished in a continuous
operation including provision of contraction, expansion, construction
and longitudinal joints, joint filler, separation membrane, sealant
primer, joint sealant, debonding strip, placing of dowel bar and tie rod
admixtures as approved, curing compound, finishing to lines and
grades as per approved drawings as per IRC-15 2002 and as per
relevant clauses of section-602 of specifications complete but excludin
cost of steel in dowel bar and tie rod etc.
Deduct from Item No.6.3 above if paver with electronic sensor is not
used and laying, compaction is done by any other method (The
acceptance criteria regarding level, thickness, surface regularity,
texture finish, strength of concrete and all other quality control
measures shall be the same as in case of machine laid work.)
Construction of Base/sub-base using cement, sand, fly ashand
coarse aggregates proportioned as per table 4 of IRC: 74/1979 and
with water content ratio, slump and compressive strength as defined in
the said table, mix prepared in a batching and mixing plant, transported
to site, laid with paver with electronic sensor and compacted with a
vibratory roller 8-10 tonnes capacity within the time limit laid down
vide clause 7.6.3 of IRC: 74-1979, construction joints properly formed
at the end of day's work, cured for 14 days, all as specified in IRC: 741979 and as per approved plans and as per relevant clauses of section600.
Deduct from Item No.6.5 above if paver with electronic sensor,
vibratory roller are not used and laying, compaction is done by any
other method. .
Unit
Rate (Rs.)
cum
1814.00
cum
150.00
cum
4440.00
cum
350.00
cum
1738.00
cum
140.00
15
Item
No.
6.7
6.8
6.9
I)
ii)
6.10
6.11
I)
ii)
Descriptions
Construction of dowel jointed, plain cement concrete pavement in M-4
grade concrete over a prepared sub base with 43 or higher grade
cement, coarse and fine aggregate conforming to IS 383, maximum siz
of coarse aggregate not exceeding 25 mm, replacing cement by fly ash
to the extent of 15% and sand by 10%, mixed in a batching and mixing
plant as per approved mix design, transported to site, laid with a fixed
form or slip form paver with electronic sensor, spread, compacted and
finished in a continuous operation including provision of contraction,
expansion, construction and longitudinal joints, joint filler, separation
membrane, sealant primer, joint sealant, debonding strip, placing of
dowel bar and tie rod, admixtures as approved, curing compound,
finishing to lines and grades as per drawing and as per relevant clauses
of section-600 but excluding cost of steel in dowel bar and tie rod etc.
Deduct from Item No.6.7 above if paver with electronic sensor is not
used and laying, compaction is done by any other method (The
acceptance criteria regarding level, thickness, surface regularity,
texture finish, strength of concrete and all other quality control
measures shall be the same as in case of machine laid work.)
Add extra in Item No.6.3 & 6.7 above for the cost of steel in dowel bar
and tie rod etc. required as per design.
Mild steel
Tor steel
Providing and laying reinforced cement concrete pipe 300mm dia NP-4
for service ducts below concrete pavement.
Providing, fixing and lowering, laying and jointing Double Walled
Corrugated (DWC) Pipes of HDPE in 6m. length bar with IS-14930-II
in prepared trenches in grade and level including cost of couplers and
testing of pipes at factory as per the stipulation in relevant IS codes etc
complete.
145mm outer diameter / 123mm inner diameter
200mm outer diameter / 174mm inner diameter
Unit
Rate (Rs.)
cum
4127.00
cum
320.00
MT
MT
38720.00
38720.00
MT
313.00
RM
RM
339.00
518.00
16
CHAPTER-R7
GEOSYNTHETICS AND REINFORCED EARTH
Item
No.
7.1
7.2
7.3
Descriptions
Laying Paving Fabric Beneath a Pavement Overlay(Providing and
laying paving fabric with physical requirements as per table 704-2 over
a tack coat of paving grade Bitumen 80-100 penetration, laid at the rate
of 1 kg per sqm over thoroughly cleaned and repaired surface to
provide a water resistant membrane and crack retarding layer. Paving
fabric to be free of wrinkling and folding and to be laid before cooling
of tack coat, brooming and rolling of surface with pneumatic roller to
maximise paving fabric contact with pavement surface as per relevant
clauses of section-700 of specifications
Laying Boulder Apron in Crates of Synthetic Geogrids(Providing,
preparing and laying of geogrid crated apron 1 m x 5 m, 600 mm thick
including excavation and backfilling with baffles at 1 metre interval,
made with geogrids having characteristics as per clause 704.2, joining
sides with connectors/ring staples, top corners to be tie tensioned,
placing of suitable cross interval ties in layers of 300 mm connecting
opposite side with lateral braces and tied with polymer braids to avoid
bulging, constructed as per clause 704.3. filled with stone with
minimum size of 200 mm and specific gravity not less than 2.65,
packed with stone spalls, keyed to the foundation recess in case of
sloping ground and laid over a layer of geotextile to prevent migration
of fines as per approved design as per relevant clauses of section-700
& 2500 f
ifi ti
Construction of Reinforced Earth Retaining Wallincluding
excavation for foundation, foundation concrete and cement concrete
grooved sealing in foundation for facing elements and placement,
assembling, joining and laying of reinforcing element complete. The
above item shall be payable only after back filling behind the wall is
completed by granular material duly watered, rolled and completed.
Unit
Rate (Rs.)
sqm
121.00
cum
544.00
(Back filling behind the facing element shall be paid separately as per
Chapter-R-3 item No.3.11)
i)
ii)
A
sqm
869.00
Type 1
metre
metre
metre
metre
metre
sqm
327.00
262.00
262.00
262.00
392.00
200.00
Type 2
Type 3
Type 4
Type 5
17
CHAPTER-R8
TRAFFIC SIGNS, MARKINGS & OTHER ROAD APPURTENANCES
Item
No.
8.1
8.2
i)
ii)
8.3
i)
ii)
iii)
iv)
v)
vi)
vii)
8.4
Descriptions
Unit
Construction of cement concrete kerb with top and bottom width 115
and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10
grade foundation 150 mm thick, foundation having 50 mm projection
metre
beyond kerb stone, kerb stone laid with kerb laying machine,
foundation concrete laid manually, all complete and as per clause 408
of specifications.
Printing new letter and figures of any shade with synthetic enamel pain
black or any other approved colour to give an even shade including cos
of paint etc. complete and as per relevant clauses of section-800 &
I.R.C.-67.
Hindi Matras commas and the like not to be measured and paid.
cm height
(For Half letter shall be counted as half)
per letter
English and Roman
cm height
per letter
Providing and fixing of retro- reflectorisedcautionary, mandatory
and informatory sign as per IRC :67 made of encapsulated lens type
reflective sheeting vide clause 801.3, fixed over aluminium sheeting,
1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm
x 6 mm (height from crown level of the road and bottom of the sign
board shall not be less than 1.5 m.) firmly fixed to the ground by mean
of properly designed foundation with M15 grade cement concrete 45
cm x 45 cm x 60 cm, 60 cm below ground level as per approved
drawing including painting of vertical post as per specification.
90 cm equilateral triangle
60 cm equilateral triangle
60 cm circular
80 cm x 60 cm rectangular
60 cm x 45 cm rectangular
60 cm x 60 cm square
90 cm high octagon
Direction and Place Identification signs upto 0.9 sqm size board.
(Providing and erecting direction and place identification retroreflectorised sign asper IRC:67 made of encapsulated lens type
reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2
mm thick with area not exceeding 0.9 sqm supported on a mild steel
single angle iron post 75 x 75 x 6 mm (height from crown level of the
road and bottom of the sign board shall not be less than 1.5 m.) firmly
fixed to the ground by means of properly designed foundation with
M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground
level as per approved drawing including painting of vertical post as
per specification.
Rate (Rs.)
168.00
0.50
0.30
each
each
each
each
each
each
each
3339.00
2186.00
2941.00
4111.00
2864.00
3398.00
5251.00
sqm
7337.00
18
Item
No.
8.5
8.6
8.7
8.8
i)
ii)
8.9
i)
8.10
Descriptions
Direction and Place Identification signs with size more than 0.9 sqm
size board. (Providing and erecting direction and place identification
retro- reflectorised sign asper IRC :67 made of encapsulated lens type
reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2
mm thick with area exceeding 0.9 sqm supported on a mild steel angle
iron post 75 mm x 75 mm x 6 mm (height from crown level of the road
and bottom of the sign board shall not be less than 1.5 m.) , 2 Nos.
firmly fixed to the ground by means of properly designed foundation
with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below
ground level as per approved drawing including painting of vertical
post as per specification.
Painting two coats after filling the surface with synthetic enamel paint
in all shades on new plastered concrete surfaces and as per relevant
clauses of section-800 & I.R.C.-67 including cost of paint etc.
complete.
Providing and applying two coats of ready mix paint of approved brand
on steel surface after through cleaning of surface to give an even shade
as per relevant clauses of section-800 & I.R.C.- 67 including cost of
paint etc. complete.
Painting lines, dashes, arrows etc on roads in two coats on new work
with ready mixed road marking paint conforming to IS:164 on
bituminous surface, including cleaning the surface of all dirt, dust and
other foreign matter, demarcation at site and traffic control as per
relevant clauses of section-800 & I.R.C.-67 including cost of paint etc.
complete.
Over 10 cm in width
Up to 10 cm in width
Painting Lines, Dashes, Arrows etc on Roads in Two Coats on Old
Work (Painting lines, dashes, arrows etc on roads in two coats on old
work with ready mixed road marking paint confirming to IS: 164 on
bituminous surface, including cleaning the surface of all dirt, dust and
other foreign matter, demarcation at site and traffic control as per
relevant clauses of section-800 of specifications.
Over 10 cm in width
Road Marking with Hot Applied Thermoplastic Compound with
Reflectorising Glass Beads on Bituminous Surface(Providing and
laying of hot applied thermoplastic compound 2.5 mm thick including
reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5
mm is exclusive of surface applied glass beads as per IRC:35 .The
finished surface to be level, uniform and free from streaks and holes
and as per relevant clauses of section-800
Unit
Rate (Rs.)
sqm
12668.00
sqm
41.00
sqm
42.00
sqm
sqm
56.00
48.00
sqm
37.00
sqm
704.00
19
Item
No.
8.11
i)
ii)
iii)
8.12
8.13
8.14
8.15
8.16
Descriptions
Providing reinforced cement concrete M15grade kilometre stone of
standard design as per IRC:8-1980, fixing in position including
painting and printing etc as per relevant clauses of section-800 of
specifications.
5th kilometre stone (precast)
Ordinary Kilometer stone (Precast)
Hectometer stone (Precast)
Road Delineators (Supplying and installation of delineators (road way
indicators, hazard markers, object markers), 80-100 cm high above
ground level, painted black and white in 15 cm wide stripes, fitted with
80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at
the top, buried or pressed into the ground and confirming toIRC-79 and
the drawings as per relevant clauses of section-800 of specifications.
Reinforced cement concrete M15 grade boundary pillars of standard
design as per IRC:25-1967, fixed in position including finishing and
lettering but excluding painting)
G.I Barbed wire Fencing 1.2 metre high(Providing and fixing 1.2
metres high GI barbed wire fencing with 1.8 m angle iron posts 40 mm
x 40 mm x 6 mm placed every 3 metres center to center founded in
M15 grade cement concrete, 0.6 metre below ground level, every 15th
post, last but one end post and corner post shall be strutted on both
sides and end post on one side only and provided with 9 horizontal line
and 2 diagonals interwoven with horizontal wires, fixed with GI
staples, turn buckles etc complete as per relevant clauses of section800 of specifications.
G.I Barbed wire Fencing 1.8 metre high(Providing and fixing 1.8
metres high GI barbed wire fencing with 2.4 m angle iron posts 50 mm
x 50 mm x 6 mm placed every 3 metres center to center founded in
M15 grade cement concrete, 0.6 metre below ground level, every 15th
post, last but one end post and corner post shall be strutted on both
sides and end post on one side only and provided with 12 horizontal
lines and 2 diagonals interwoven with horizontal wires, fixed with GI
staples, turn buckles etc complete as per clause 807 as per relevant
clauses of section-800 of specifications
Tubular Steel Railing on Medium Weight steel channel ( ISMC
series) 100 mm x 50 mm (Providing, fixing and erecting 50 mm dia GI
pipe (medium class) railing in 3 rows duly painted on medium weight
steel channels (ISMC series) 100 mm x 50 mm, 1.2 metres high above
ground, 2 m centre to centre, complete as per approved drawings as per
relevant clauses of section-800 of specifications.
Unit
Rate (Rs.)
each
each
each
2027.00
1225.00
348.00
each
266.00
each
300.00
metre
194.00
metre
322.00
metre
1439.00
20
Item
No.
8.17
8.18
i)
8.19
a)
b)
8.20
Descriptions
Unit
Rate (Rs.)
1086.00
2278.00
2599.00
metre
4589.00
each
656.00
21
Item
No.
8.21
8.22
8.23
a)
b)
8.24
Descriptions
Traffic Cone (Provision of red fluorescent with white reflective sleeve
traffic cone made of low density polyethylene (LDPE) material with a
square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in
weight, placed at 1.5 m interval, all as per BS 873)
Portable Barricade in Construction Zone(Installation of a steel
portable barricade with horizontal rail 300 mm wide, 2.5 m in length
fitted on a 'A' frame made with 45 x 45 x 5 mm angle iron section, 1.5
m in height, horizontal rail painted (2 coats) with yellow and white
stripes, 150 mm in width at an angle of 45 Degrees, 'A' frame painted
with 2 coats of yellow paint, complete as per IRC:SP:55-2001 )
Permanent Type Barricade in Construction Zone
With Steel Components (Construction of a permanent type
barricade made of steel components, 1.5 m high from road level,
fitted with 3 horizontal rails 200 mm wide and 4 m long on 50 x 50 x
5 mm angle iron vertical support, painted with yellow and white
strips, 150 mm in width at an angle of450, complete as per
IRC:SP:55-2001)
With Bricks (Construction of a permanent type barricade made with
brick work in mud mortar, 1.5 m high, 4 m long, 600 mm thick,
plastered with cement mortar 1:6, painted with yellow and white
strips)
Drum Delineator in Construction Zone(Provision of metal
drum/empty bitumen drum delineator, 300 mm in diameter, 800 mm
high, filled with earth for stability, painted in circumferential strips of
alternate black and white 100 mm wide fitted with reflectors 3 Nos of
7.5 cm dia, all as per IRC:SP:55-2001)
Unit
Rate (Rs.)
each
191.00
each
2075.00
each
3319.00
each
5945.00
each
374.00
22
CHAPTER-R9
SUPPLY OF MATERIAL
Item
No.
9.1
i)
ii)
iii)
iv)
v)
vi)
vii)
viii)
ix)
9.2
i)
ii)
iii)
9.3
Note :
9.4
i)
ii)
iii)
iv)
Descriptions
Supply of mineral aggregate like broken stone/crushed stone (crushed
in mechanical crusher) as per clause 514 at road site including all lead
and stacking etc. complete.
75mm standard size broken stone
63mm standard size broken stone
45mm standard size broken stone
45mm standard size crushed stone
26.5mm standard size crushed stone
22.4mm standard size crushed stone
13.2mm standard size crushed stone
11.2mm standard size crushed stone
6.7mm standard size crushed stone
Supply as per clause 514 including all lead and stacking etc. complete.
Crusher stone dust (clause 507.2.3)
Sand/Shingle/Kanker/Laterite
Moorum with CBR not less than 20 and P.I. Not exceeding 6.
Supply of binding material at road site having P.I. Value less than 6
confirming to clause 404.2.7.
In case of suitable binding material having a P.I. Value of less than 6
is not available within reasonable distances. The contractor (at his
own cost) may add an admixture of lime to lower down the P.I. to
bring it within the above range. A factor of safety of 2 should be
applied to the results of laboratory to decide the percentage of lime to
be added.
Supply and stacking of aggregates, precoated with 1% of its weight
with bitumen as per clause 514 t work site.
22.4 mm size
13.2 mm size
11.2 mm size
6.7 mm size
Unit
Rate (Rs.)
cum
cum
cum
cum
cum
cum
cum
cum
cum
263.75
301.25
331.25
452.50
528.75
528.75
603.75
452.50
377.50
cum
cum
cum
188.75
188.75
151.25
cum
151.25
cum
cum
cum
cum
710.00
742.50
581.25
528.75
23
CHAPTER-R10
MAINTENANCE OF ROADS
Item
No.
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
(i)
(ii)
10.9
(i)
(ii)
10.10
(i)
(ii)
Descriptions
Filling Pot- holes and Patch Repairs with open - graded Premix
surfacing, 20mm. (Removal of all failed material, trimming of
completed excavation to provide firm vertical faces, cleaning of
surface, painting of tack coat on the sides and base of excavation as
per clause 503, back filling the pot holes with hot bituminous material
as per clause 511, compacting, trimming and finishing the surface to
form a smooth continuous surface, all as per clause 3004.2)
Providing, laying and rolling of open - graded premix surfacingof
20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using
60/70 grade bitumen to required line, grade and level to serve as
wearing course on a previously prepared base, including mixing in a
concrete mixer or cold mix plant laying with paver finisher and rolling
with a smooth wheeled roller 8-10 tonne capacity, finished to required
level and grades excluding primer and tack coat and as per relevant
clauses of section-500.
Crack Filling (Filling of crack using slow - curing bitumen emulsion
and applying crusher dust in case crack are wider than 3mm.) As per
relevant clauses of section-3000
Dusting (Applying crusher dust to areas of road where bleeding of
excess bitumen has occurred.) As per relevant clauses of section-3000.
Unit
Rate (Rs.)
sqm
84.00
sqm
58.00
metre
1.80
sqm
0.40
1046.00
15.00
2107.00
216.00
164.00
86.00
55.00
22.00
14.00
24
Item
No.
10.11
(i)
(ii)
10.12
(i)
(ii)
10.13
(i)
(ii)
10.14
(i)
(ii)
10.15
(i)
(ii)
Descriptions
Providing painting, figuring and numbering to culvert upto 6m. Span
complete with Synthetic Enamal Paint.
Two coats on new work.
One coat on old work.
Providing painting, figuring and numbering to minor bridges upto 30m
Linear water-way complete with Synthetic Enamal Paint .
Two coats on new work.
One coat on old work.
Providing painting, figuring & numbering to major bridges, linear
water-way exceeding 30m. Complete with Synthetic Enamal Paint .
Two coats on new work.
One coat on old work.
Providing painting to angle Iron posts of road sign boards complete
with Synthetic Enamal Paint.
Two coats on new work.
One coat on old work.
Providing painting and figuring of road sign boards (excluding
posts/kerbs)
Two coats on new board.
One coat on old board.
Unit
Rate (Rs.)
Each
Each
68.00
53.00
Each
Each
91.00
79.00
Each
Each
150.00
120.00
Each
Each
64.00
59.00
sqm
sqm
190.00
166.00
25
CHAPTER-R11
HORTICULTURE
Item
No.
11.1
11.2
11.3
11.4
11.5
Descriptions
Unit
Rate (Rs.)
159.00
320.00
721.00
14.00
1972.00
26
CHAPTER-R12
SURVEY & INVESTIGATION, PREPARATION OF D.P.R. AND OTHER
MISCELLANEOUS ITEMS
Item
No.
12.1
i)
ii)
iii)
12.2
a)
b)
c)
Descriptions
Unit
Rate (Rs.)
Km.
Km.
Km.
6600.00
7300.00
8200.00
Each
Each
Each
2840.00
3460.00
4180.00
Survey and investigation and preparation of DPR for road work with
chain and compass, auto level, theodolite or total station i/c fixing of
permanent benchmark and also fixing of bench mark on all the
permanent structures, along the alignment, like boundary wall,
electrical poles etc. Also marking of locations of boundary wall,
electric poles, telephone poles trees etc. in the road boundary, collectio
and submission of existing inventory of the road all along the alignmen
conducting survey@20 metre interval for L-section and for single lane
X-section interval will be @ 0.75, 1.25, 1.875, 2.60, 3.75, 4.50, 5.50
and 6.50 metre on both side of centre line for two lane four lane
interval for x-section shall be as specified in MORT&H Specifications
Data collected as specified above are required to be submitted in both
hard and soft copies, L-section, X-section and plan is required to be
submitted in the shape of drawing sheets drawn with the help of auto
plotter.
Soil samples @ every 500 metre or wherever soil appears to change its
properties are required to be collected and soil investigation for LL,
PL, swelling index and CBR are to be conducted and result too be
submitted along with the project report.
Job also includes collection of data for traffic census fixing of RTL
getting it approved from Engineer-in-Charge and accordingly
submission of pavement design in accordance with relevant clauses of
IRC. Preparation of estimate complete and submission of same in eigh
copies duly spiral binded.
For single lane road
For two lane road
For four lane road
Performing details survey and investigation and collection of hydraulic
data (essential design data as per IRC special publication No.13
guidelnes for small bridges and culvert) regarding catfchment area, Lsection of road and nalla, cross-section of nalla at the point of crossing
at upstream and down stream as well as T.P. section result ascertaining
and making of HFL/OFL transferring and fixing of pucca bench mark
at site etc. complete i/c of all necessary material and labour required
for survey work after collection of all data prepare all drawing estimate
with computer in eight copies, duly spiral binded.
For catchment area less then 1.25 Sq.Km.
For catchment area 1.25 to 2.50 Sq.Km.
For catchment area beyond then 2.50 Sq.Km.
27
CHAPTER-R13
VIDEO PHOTOGRAPHY
Item
No.
13.1
i)
ii)
iii)
13.2
i)
ii)
iii)
iv)
v)
Descriptions
Providing and carrying out video shoting of roads, bridges, buildings,
other programmes including hiring of vehicle equipments for video
shooting, titling, lightening, mixing, lettering, editing, including cost of
two colour CDs of approved makes and quality etc. complete.
Within 50 Kms.
Beyond 50 kms.
Work upto 5 hours per day only.
Shooting of still photographs outdoor and indoor of construction and
other works of building, bridges, roads etc. at any distances.
Post Card size
4"x6" size
5"x7" size
8"x12" Size (A-4 Size)
20''x30'' size (Banner Size)
Extra Copies :
Post Card size
4"x6" size
5"x7" size
8"x12" Size (A-4 Size)
20'x30' size (Banner Size)
Unit
Rate (Rs.)
Per day
Per day
Per day
2500.00
2700.00
1500.00
3 Nos.
3 Nos.
3 Nos.
3 Nos.
1 No.
60.00
85.00
135.00
250.00
600.00
1 No.
1 No.
1 No.
1 No.
1 No.
8.00
12.00
15.00
50.00
450.00
28
CHAPTER-B1
FOUNDATIONS
Item
No.
1.1A
I
i)
ii)
iii)
II
i)
ii)
iii)
II
i)
ii)
iii)
III
i)
ii)
iii)
IV
i)
ii)
iii)
V
VI
1.1B
a)
b)
c)
1.2
1.3
1.4
Descriptions
Unit
Rate (Rs.)
cum
cum
cum
94.00
103.00
154.00
cum
cum
cum
333.00
361.00
388.00
cum
cum
cum
cum
cum
cum
cum
cum
cum
cum
cum
cum
cum
575.00
604.00
630.00
475.00
504.00
530.00
934.00
961.00
989.00
213.00
66.00
50% extra
75% extra
100% extra
cum
2652.00
cum
2652.00
cum
2707.00
29
Item
No.
1.5
a)
b)
1.6
a)
b)
c)
d)
e)
f)
g)
g)
1.7
1.8
A
i)
ii)
iii)
B
I)
ii)
iii)
iv)
v)
vi)
vii)
viii)
C
i)
ii)
iii)
iv)
D
I)
ii)
iii)
Descriptions
Provdiing Stone masonry work in cement mortar 1:3 in foundation
complete as drawing and Technical Specification and as per relevant
clauses of sections 1400 with .
Coursed rubble masonry( first sort )
Random Rubble Masonry (Coursed or uncoarsed)
Provdiing and laying Plain/Reinforced cement concrete in open
foundation including form work shuttering etc. complete as per drawin
and technical specifications and as per relevant clauses of sections
1500, 1700 & 2100 with .
PCC Grade M15
PCC Grade M20
PCC Grade M25
PCC Grade M30
RCC Grade M20
RCC Grade M25
RCC Grade M30
RCC Grade M35
Providing and laying cutting edge of mild steel weighing 40 kg per
metre for well foundation complete as per drawing and technical
specification and as per relevant clauses of sections 1200 & 1900.
Providing and laying Plain/Reinforced cement concrete, in well
foundation complete as per drawing and technical specification and as
per relevant clauses of sections 1200, 1500 & 1700 for
Well curb
RCC M20 Grade
RCC M25 Grade
RCC M35 Grade
Well steining
PCC M15 Grade
PCC M20 Grade
PCC M25 Grade
PCC M30 Grade
RCC M20 Grade
RCC M25 Grade
RCC M30 Grade
RCC M35 Grade
Bottom Plug
PCC Grade M20
PCC Grade M25
PCC Grade M30
PCC Grade M35
Intermediate plug
Grade M20 PCC
Grade M25 PCC
Grade M30 PCC
Unit
Rate (Rs.)
cum
cum
2671.00
2719.00
cum
cum
cum
cum
cum
cum
cum
cum
3117.00
3567.00
3936.00
3967.00
3607.00
3981.00
3994.00
4078.00
tonne
60618.00
cum
cum
cum
4162.00
4606.00
4753.00
cum
cum
cum
cum
cum
cum
cum
cum
3298.00
3772.00
4173.00
4216.00
3815.00
4222.00
4245.00
4357.00
cum
cum
cum
cum
4074.00
4303.00
4344.00
4441.00
cum
cum
cum
3897.00
4116.00
4156.00
30
Item
No.
E
i)
ii)
iii)
iv)
F
i)
ii)
iii)
1.9
Descriptions
Unit
Rate (Rs.)
cum
cum
cum
cum
2998.00
3429.00
3794.00
3833.00
cum
cum
cum
3566.00
3981.00
3994.00
cum
cum
cum
cum
271.00
348.00
550.00
1108.00
A
i)
ii)
iii)
iv)
Top plug
Grade M15 PCC
Grade M20 PCC
Grade M25 PCC
Grade M30 PCC
Well cap
RCC Grade M20
RCC Grade M25
RCC Grade M30
Sinking well for foundation to levels as per drawing including dredging
dewatering and drop chiselling as may be necessary, including sinking
by loading with necessary kentledges and other usual means for the
type of work i/c all the needed plant and machinery etc. complete as
directed and removal of boulders or tree trunks each upto 0.03 cum.
average volume except sinking in rock or removal of boulder each mor
than 0.03 cum. volume etc. complete (Note: Measured from top of
cutting edge angle to bottom of well cap or L.W.L. whichever in lower
as per section 1200.
Sandy soil
upto 3.0 m. depth
Beyond 3m upto 10m depth
Beyond 10m upto 20m depth
Beyond 20m depth below bed level
B
i)
ii)
iii)
in clayey soil
upto 3.0 m. depth
Beyond 3m upto 10m depth
Beyond 10m upto 20m depth
cum
cum
cum
408.00
509.00
806.00
iv)
cum
1590.00
C
i)
D
cum
194.00
cum
688.00
cum
1306.00
cum
950.00
tonne
55646.00
metre
5530.00
1.10
1.11
1.12
31
Item
No.
1.13
1.14
1.15
1.16
1.17
1.18
1.19
1.20
1.21
1.22
1.23
1.24
Descriptions
Providing bored cast-in-situ M-35 grade R.C.C. pile excluding
reinforcement complete as per drawing and technical specifications and
removal of excavated earth with all lifts and lead upto 1000 m. (Pile
diameter-1000 mm) and as per specifications 1100, 1600 and 1700.
Providing bored cast-in-situ M-35 grade R.C.C. pile excluding
reinforcement complete as per drawing and technical specifications and
removal of excavated earth with all lifts and lead upto 1000 m. (Pile
diameter-1200 mm) and as per specifications 1100, 1600 and 1700.
Providing driven cast-in-place vertical M-35 grade R.C.C. pile
excluding reinforcement complete as per drawing and & Technical
Specification (Pile diameter - 750 mm)and as per specifications 1100,
1600 and 1700.
Providing driven cast-in-place vertical M-35 grade R.C.C. piles
excluding reinforcement complete as per drawing and & Technical
Specification (Pile diameter - 1000 mm) and as per specifications
1100, 1600 and 1700.
Providing driven cast-in-place vertical M-35 grade R.C.C. piles
excluding reinforcement complete as per drawing and & Technical
Specification (Pile diameter - 1200 mm) and as per specifications
1100, 1600 and 1700.
Providing driven precast vertical M-35 grade R.C.C. piles excluding
reinforcement complete as per drawing and & Technical Specification
(Pile Diameter=500 mm) and as per specifications 1100, 1600 and
1700.
Providing driven precast vertical M-35 grade R.C.C. piles excluding
reinforcement complete as per drawing and & Technical Specification
(Pile Diameter=750 mm) and as per specifications 1100, 1600 and
1700.
Providing driven precast vertical M-35 grade R.C.C. piles excluding
reinforcement complete as per drawing and & Technical Specification
(Pile Diameter=1000 mm) and as per specifications 1100, 1600 and
1700.
Providing driven precast vertical M-35 grade R.C.C. piles excluding
reinforcement complete as per drawing and & Technical Specification
(Size of pile - 300 mm x 300 mm) and as per specifications 1100, 1600
and 1700.
Providing driven precast vertical M-35 grade R.C.C. piles excluding
reinforcement complete as per drawing and & Technical Specification
(Size of pile - 500 mm x 500 mm) and as per specifications 1100, 1600
and 1700.
Providing driven precast vertical M-35 grade R.C.C. piles excluding
reinforcement complete as per drawing and & Technical Specification
(Size of pile - 750 mm x 750 mm) and as per specifications 1100, 1600
and 1700.
Providing pile load test on single vertical pile in accordance with
IS:2911(Part-IV)
Unit
Rate (Rs.)
metre
8847.00
metre
10943.00
metre
4158.00
metre
6128.00
metre
8064.00
metre
3716.00
metre
4330.00
metre
5840.00
metre
3080.00
metre
3356.00
metre
4613.00
tonne
350.00
32
Item
No.
1.25
a)
b)
c)
d)
1.26
1.27
1.28
1.29
a)
b)
c)
1.30
Descriptions
Provdiing and laying Cement concrete for reinforced concrete in pile
cap complete as per drawing and Technical Specification and as per
relevant clauses of sections 1100, 1500 & 1700 with
RCC Grade M20
RCC Grade M25
RCC Grade M30
RCC Grade M35
Providing and laying Levelling course in PCC M-15 below Pile cap as
per drawing and as per section 1100 and 1700.
Supplying, fitting and placing un-coated HYSD bar reinforcement in
foundation complete as per drawing and technical specifications and as
per relevant clauses of sections 1600.
Supplying, fitting and placing un-coated Mild steel reinforcement
complete in foundation as per drawing and technical specification and
as per relevant clauses of sections 1600.
Taking, exploratory boring 100mm dia at the location of piers and
abutments or for high embankments in approaches in all types of strata
as per IRC-78-1983 and section 2400 of specifications.
Upto 1.0 m below bed level
Beyond 1.0 m depth upto 5.0 m
Beyond 5.0 m depth
Providing and laying 1.5 m deep in rock and 1.5 m above rock 25mm
dia tor steel dowel bar in foundation including drilling 65mm dia bore
hole in rock necessary bending, hooking tying reinforcement in position
and grouting etc. complete as per drawing and specifications.
Unit
Rate (Rs.)
cum
cum
cum
cum
3569.00
3966.00
4016.00
4121.00
cum
2963.00
tonne
44291.00
tonne
44438.00
metre
metre
metre
1320.00
1380.00
1440.00
each
840.00
33
CHAPTER-B2
SUB-STRUCTURE
Item
No.
2.1A
2.1B
2.2
2.3
2.4
a)
b)
2.5
A
a)
b)
B
a)
b)
C
a)
b)
c)
D
a)
b)
c)
E
a)
b)
c)
F
a)
b)
c)
G
a)
b)
c)
Descriptions
Providing Brick masonry work in 1:3 in sub-structure complete
excluding pointing and plastering, as per drawing and technical
specifications and as per relevant clauses of sections 1300.
Add extra to item 13.1A above if fly ash bricks are used.
Providing Pointing with cement mortar (1:3 ) on brick work in
substructure as per Technical specifications and as per relevant clauses
of sections 1300.
Providing Plastering with cement mortar (1:3 ) on brick work in substructure as per Technical specifications and as per relevant clauses of
sections 1300.
Providing Stone masonry work in cement mortar 1:3 for substructure
complete as per drawing and Technical Specifications and as per
relevant clauses of sections 1400 in
Random Rubble Masonry
Coursed rubble masonry (first sort )
Providing and laying Plain/Reinforced cement concrete in sub-structure
or complete RCC Box section as per drawing and technical
specifications and as per relevant clauses of sections 1500, 1700 &
2200 in (Height above average ground level)
PCC Grade M15
Height upto 5m
Height beyond 5m and upto 10m
PCC Grade M20
Height upto 5m
Height beyond 5m and upto 10m
PCC Grade M25
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
PCC Grade M30
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
RCC Grade M20
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
RCC Grade M25
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
RCC Grade M30
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
Unit
Rate (Rs.)
cum
2729.00
cum
200.00
sqm
34.90
sqm
81.00
cum
cum
2793.00
2872.00
cum
cum
3117.00
3207.00
cum
cum
3567.00
3657.00
cum
cum
cum
3936.00
4325.00
4515.00
cum
cum
cum
3967.00
4370.00
4561.00
cum
cum
cum
3607.00
3954.00
4128.00
cum
cum
cum
3981.00
4360.00
4567.00
cum
cum
cum
3994.00
4365.00
4535.00
34
Item
No.
H
a)
b)
c)
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
Descriptions
RCC Grade M35
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
Supplying, fitting and placing HYSD bar reinforcement in substructure complete as per drawing and technical specifications and as
per relevant clauses of sections 1600.
Supplying, fitting and placing Mild steel reinforcement complete in
sub-structure as per drawing and technical specification and as per
relevant clauses of sections 1600.
Providing weep holes in Brick masonry/Plain/Reinforced concrete
abutment, wing wall/return wall with 100 mm dia AC pipe, extending
through the full width of the structure with slope of 1V :20H towards
drawing foce. Complete as per drawing and Technical specifications
and as per clause 2706 of specifications.
Providing Back filling behind abutment, wing wall and return wall
with Granular Material complete as per drawing and Technical
specification and as per relevant clauses 305 of specifications and as
per appendix 6 of IRC-78
Providing and laying of Filter media with granular materials/stone
crushed aggregates satisfying the requirements laid down in clause
2504.2.2. of MORTH specifications to a thickness of not less than 600
mm with smaller size towards the soil and bigger size towards the wall
and provided over the entire surface behind abutment, wing wall and
return wall to the full height compacted to a firm condition complete as
per drawing and technical specification.
Supplying, fitting and fixing in position true to line and level sliding
plate bearing with PTFE surface sliding on stainless steel complete
including all accessories as per drawing and Technical Specifications
and BS: 5400, section 9.1 & 9.2 (for PTFE) and as per relevant
clauses of sections 2000.
Supplying, fitting and fixing in position true to line and level sliding
plate bearing with stainless steel plate sliding on stainless steel plate
with mild steel matrix complete including all accessories as per
drawing and Technical Specifications and as per relevant clauses of
sections 2000.
Supplying, fitting and fixing in position true to line and level POTPTFE bearing consisting of a metal piston supported by a disc or
unreinforced elastomer confined within a metal cylinder, sealing rings
dust seals, PTFE surface sliding against stainless steel mating surface,
completre assembly to be of cast steel/fabricated structural steel, metal
and elastomer elements to be as per IRC: 83 part-I & II respectively
and other parts conforming to BS: 5400, section 9.1 & 9.2 complete
asper drawing and approved technical specifications and as per
relevant clauses of sections 2000.
Unit
Rate (Rs.)
cum
cum
cum
4078.00
4452.00
4594.00
tonne
44344.00
tonne
44049.00
metre
98.00
cum
415.00
cum
721.00
per tonne
capacity
242.00
per tonne
capacity
242.00
per tonne
capacity
130.00
35
Item
No.
2.14
2.15
2.16
2.17
a)
b)
2.18
a)
b)
2.19
a)
b)
2.20
a)
b)
2.21
2.22
Descriptions
Supplying, fitting and fixing in position true to line and level
elastomeric bearings confirming to IRC:83:(Pt.II) section IX complete
including all accessories as per drawing and specifications as per
section 2000.
Providing and fixing in position bituminous paper bearing for slabs as
per approved drawing and confirming to IS:1398.
Providing P.C.C. M-10 Nominal mix for hume pipe culverts in
foundation and sub structure etc. as per drawing and as per relevant
clauses of section 1500, 1700, 2100 and 2900.
Providing and Laying Reinforced cement concrete pipe
NP4/prestressed concrete pipe for culverts on first class bedding of
granular material in single row including fixing collar with cement
mortar 1:2 but excluding excavation, protection works, backfilling,
concrete and masonry works in head walls and parapets and as per
relevant clauses of section-2900
1000 mm dia
1200 mm dia
Providing and Laying Reinforced cement concrete pipe NP4 /prestrssed
concrete pipe for culverts on first class bedding of granular material in
double row including fixing collar with cement mortar 1:2 but
excluding excavation, protection works, backfilling, concrete and
masonry works in head walls and parapets and as per relevant clauses
of section-2900.
1000 mm dia
1200 mm dia
Providing and Laying Reinforced cement concrete pipe NP4 /prestrssed
concrete pipe for culverts on first class bedding of granular material in
triple row including fixing collar with cement mortar 1:2 but excluding
excavation, protection works, backfilling, concrete and masonry
works in head walls and parapets and as per relevant clauses of section2900.
1000 mm dia
1200 mm dia
Add for every additional rowin item No.2.19.
1000 mm dia
1200 mm dia
Providing first class bedding below hume pipes with granular material
as per clause 2904 of specifications. (in case of item No.2.20 for every
additional row)
Providing concrete craddle bedding in M-15 grade concrete as per
clause 2900 and as per section 1700 and 2900.
Unit
Rate (Rs.)
Cu.Cm.
0.65
sqm
43.00
cum
2252.00
metre
metre
5571.00
8076.00
metre
metre
11208.00
16224.00
metre
metre
17022.00
24678.00
metre
metre
5645.00
8162.00
cum
616.00
cum
3117.00
36
CHAPTER-B3
SUPER-STRUCTURE
Item
No.
3.1
A
(i)
a)
b)
c)
(ii)
a)
b)
c)
B
(i)
a)
b)
c)
(ii)
a)
b)
c)
C
(i)
a)
b)
c)
(ii)
a)
b)
c)
(iii)
a)
b)
c)
D
(i)
a)
b)
c)
(ii)
a)
b)
c)
Descriptions
Providing and laying Reinforced/Prestressed cement concrete in superstructure as per drawing and Technical Specification and as per
relevant clauses of sections 1500, 1700 and 2300 in
RCC Grade M20
For solid slab super-structure
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For T-beam & slab
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
RCC Grade M25
For solid slab super-structure
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For T-beam & slab
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
RCC Grade M 30
For solid slab super-structure
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For T-beam & slab
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For box girder and balanced cantilever
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
RCC/PSC Grade M35
For solid slab super-structure
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For T-beam & slab
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
Unit
Rate (Rs.)
cum
cum
cum
4115.00
4286.00
4458.00
cum
cum
cum
4286.00
4458.00
4629.00
cum
cum
cum
4573.00
4763.00
4954.00
cum
cum
cum
4763.00
4954.00
5144.00
cum
cum
cum
4641.00
4835.00
5028.00
cum
cum
cum
4835.00
5028.00
5221.00
cum
cum
cum
5337.00
5724.00
6111.00
cum
cum
cum
4683.00
4881.00
5080.00
cum
cum
cum
4881.00
5080.00
5278.00
37
Item
No.
(iii)
a)
b)
c)
E
(i)
a)
b)
c)
(ii)
a)
b)
c)
(iii)
a)
b)
c)
F
(i)
a)
b)
c)
(ii)
a)
b)
c)
(iii)
a)
b)
c)
G
(i)
a)
b)
c)
H
(i)
a)
b)
c)
3.2
Descriptions
For box girder and balanced cantilever
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
PSC Grade M-40
For solid slab super-structure
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For T-beam & slab
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For box girder and balanced cantilever
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
PSC Grade M-45
For solid slab/voided slab super-structure
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For T-beam & slab including launching of precast girders by
launching truss upto 40 m span
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
For cast-in-situ box girder, segmental construction and balanced
cantilever
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
PSC Grade M-50
For cast-in-situ box girder, segmental construction and balanced
cantilever
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
PSC Grade M- 55
For cast-in-situ box girder, segmental construction and balanced
cantilever
Height upto 5m
Height beyond 5m and upto 10m
Height above 10m
a) Supplying, fitting and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications as per
relevant clauses of section 1600 of specifications.
Unit
Rate (Rs.)
cum
cum
cum
5476.00
5873.00
6270.00
cum
cum
cum
5110.00
5323.00
5536.00
cum
cum
cum
5323.00
5536.00
5749.00
cum
cum
cum
5876.49
6302.00
6728.00
cum
cum
cum
5055.00
5273.00
5490.00
cum
cum
cum
5273.00
5490.00
5708.00
cum
cum
cum
5926.00
6362.00
6798.00
cum
cum
cum
6122.00
6575.00
7029.00
cum
cum
cum
6496.00
6978.00
7459.00
tonne
44976.00
38
Item
No.
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
Descriptions
Providing High tensile steel wires/strandsincluding all accessories
for stressing, stressing operations and grouting complete as per
drawing and Technical Specifications and as per relevant clauses of
section 1800.
Providing and laying Cement concrete wearing coatM-30 grade
including reinforcement complete as per drawing and Technical
Specifications and as per relevant clauses of sections 1500, 1700 and
Clause 2702 of specifications..
Providing and laying 12 mm thickmastic asphalt wearing course on
top of deck slab excluding prime coat with paving grade bitumen
meeting the requirements given in table 500-29, prepared by using
mastic cooker and laid to required level and slope after cleaning the
surface, including providing antiskid surface with bitumen precoated
fine grained hard stone chipping of 9.5 mm nominal size at the rate of
0.005cum per 10 sqm and at an approximate spacing of 10 cm center
to center in both directions, pressed into surface when the temperature
of surfaces not less than 100 deg. C, protruding 1 mm to 4 mm over
mastic surface, all complete as per clause 515 and 2702 of
specifications..
Construction of precast RCC railing of M30 Grade, aggregate size not
exceeding 12 mm, true to line and grade, tolurence of vertical RCC
post not to exceed 1 in 500, centre to centre spacing between vertical
post not to exceed 2000 mm, leaving adequate space between vertical
post for expansion, complete as per approved drawings and technical
specification and as per relevant clauses of sections 1500, 1600, 1700
and clause 2703 of specifications (as per MoST specification drawing
SD/202 or SD/305)
Construction of RCC railing of M30 Grade in-situ with 12 mm
nominal size aggregate, true to line and grade, tolurence of vertical
RCC post not to exceed 1 in 500, centre to centre spacing between
vertical post not to exceed 2000 mm, leaving adequate space between
vertical post for expansion, complete as per approved drawings and
technical specifications and as per relevant clauses of sections 1500,
1600, 1700 and clause 2703 of specifications (as per MoST
specification drawing SD/201 or SD/304)
Providing, fitting and fixingmild steel railingcomplete as per
standard drawing No.BD/1-88 and Technical Specification and as per
relevant clauses of section 1900 and 2700
Providing Drainage Spouts complete as per drawing and Technical
specification and as per clause 2705 of specifications.
Providing PCC M15 Grade leveling course below approach slab
complete as per drawing and Technical specification and as per
relevant clauses of section 1700.
Unit
Rate (Rs.)
tonne
104331.00
cum
7130.00
sqm
190.00
metre
1202.00
metre
1167.00
metre
2190.00
each
722.00
cum
3117.00
39
Item
No.
3.11
3.12
3.13
3.14
i)
ii)
iii)
iv)
3.15
Descriptions
Providing and laying Reinforced cement concreteapproach slab in M25 grade concrete including reinforcement and formwork complete as
per drawing and Technical specification and as per relevant clauses of
section 1500, 1600, 1700 and clause 2704 of specifications..
Providing and fixing Helical pipes of 600mm dia in voided concrete
slabs including 20mm dia tie rod and sealing joints etc. as per section
1700 and 1800.
Providing and laying a burried expansion joint, expansion gap being
20 mm, covered with 12 mm thick, 200 mm wide galvanised
wieldable structural steel plate as per IS: 2062, placed symmetrical to
centre line of the joint, resting freely over the top surface of the deck
concrete, welding of 8 mm dia. 100 mm long galvanised nails spaced
300 mm c/c along the centre line of the plate, all as specified in clause
2604.
Filler joint
Providing & fixing 2 mm thick and 200mm wide corrugatedcopper
plate in expansion joint complete as per drawing & Technical
Specification and as per relevant clauses of section 2600.
Providing & fixing 20 mm thick & 25cm deep compressiblefibre
board in expansion joint complete as per drawing & Technical
Specification and as per relevant clauses of section 2600
Providing and fixing in position 20 mm thick & 300mmdeep
premoulded joint fillerin expansion joint for fixed ends of simply
supported spans not exceeding 10 m to cater for a horizontal
movement upto 20 mm, covered with sealant complete as per
drawing and technical specifications and as per relevant clauses of
section 2600.
Providing and fillingjoint sealing compoundas per drawings and
technical specifications with coarse sand and 6% bitumen by weight
and as per relevant clauses of section 2600
Providing and laying ofasphaltic plug jointto provide for horizontal
movement of 25 mm and vertical movement of 2 mm, depth of joint
varying from 75 mm to 100 mm, width varying from 500 mm to 750
mm (in traffic direction), covered with a closure plate of 200mm x
6mm of wieldable structural steel conforming to IS: 2062, asphaltic
plug to consist of polymer modified bitumen binder, carefully selected
single size aggregate of 12.5 mm nominal size and a heat resistant foam
caulking/backer rod, all as per approved drawings and specifications
and as per relevant clauses of section 2600
Unit
Rate (Rs.)
cum
6059.00
metre
232.00
metre
6329.00
metre
2101.00
metre
272.00
metre
184.00
metre
11.00
metre
819.00
40
Item
No.
3.16
3.17
3.18
3.19
3.20
3.21
3.22
3.23
3.24
Descriptions
Providing and laying of anelastomeric slab steel expansion joint,
catering to right or skew (less than 20 deg., moderately curved with
maximum horizontal movement upto 50 mm, complete as per
approved drawings and standard specifications to be installed by the
manufacturer/supplier or their authorised representative ensuring
compliance to the manufacturer's instructions for installation as per
clause 2606 of specifications.
Providing and laying ofcompression seal joint consisting of steel
armoured nosing at two edges of the joint gap suitably anchored to the
deck concrete and a preformed chloroprene elastomer or closed cell
foam joint sealer compressed and fixed into the joint gap with special
adhesive binder to cater for a horizontal movement upto 40 mm and
vertical movement of 3 mm. and as per relevant clauses of section
2600.
Providing and laying of a strip seal expansion jointcatering to
maximum horizontal movement upto 70 mm, complete as per
approved drawings and standard specifications to be installed by the
manufacturer/supplier or their authorised representative ensuring
compliance to the manufacturer's instructions for installation and as per
relevant clauses of section 2600
Providing and laying of a modular strip Box steel expansion joint
including anchorage catering to a horizontal movement beyond 70 mm
and upto 140mm, complete as per approved drawings and standard
specifications to be installed by the manufacturer/supplier or their
authorised representative ensuring compliance to the manufacturer's
instructions for installation and as per relevant clauses of section 2600.
Unit
Rate (Rs.)
metre
13302.00
metre
7147.00
metre
6657.00
metre
13933.00
13937.00
600.00
44280.00
1000.00
751.00
41
CHAPTER-B4
RIVER TRAINING AND PROTECTION WORKS
Item
No.
4.1
a)
4.2
4.3
4.4
a)
b)
4.5
4.6
4.7
a)
b)
c)
4.8
a)
b)
Descriptions
Unit
Rate (Rs.)
cum
873.40
cum
1209.80
cum
3496.90
cum
873.40
cum
3496.90
cum
908.50
sqm
247.25
cum
cum
cum
1897.50
4187.00
1955.00
cum
cum
2671.00
3117.00
42
Item
No.
4.9
4.10
4.11
Descriptions
Construction of flexible apron 1 m thick comprising of loose stone
boulders weighing not less than 40 kg beyond curtain wall and as per
relevant clauses of section 2500
Gabian Structure for Retaining Earth(Providing and construction of
a gabain structure for retaining earth with segments of wire crates of
size 7 m x 3 m x 0.6 m each divided into 1.5 m compartments by cross
netting, made from 4 mm galvanised steel wire @ 32 kg per 10 sqm
having minimum tensile strength of 300 Mpa conforming to IS:280 and
galvanizing coating conforming to IS:4826, woven into mesh with
double twist, mesh size not exceeding 100 x 100 mm, filled with
boulders with least dimension of 200 mm, all loose ends to be tied wit
4 mm galvanised steel wire) and as per specification in section 2500.
Gabian Structure for Erosion Control, River Training Works and
Protection works (Providing and constructing gabain structures for
erosion control, river training works and protection works with wire
crates of size 2 m x 1 m x 0.3 m each divided into 1m compartments by
cross netting, made from 4 mm galvanised steel wire @ 32 kg per 10
sqm having minimum tensile strength of 300 Mpa conforming to
IS:280 and galvanizing coating conforming to IS:4826, woven into
mesh with double twist, mesh size not exceeding 100 mm x 100 mm,
filled with boulders with least dimension of 200 mm, all loose ends to
be securely tied with 4 mm galvanised steel wire.) and as per
specification in section 2500.
Unit
Rate (Rs.)
cum
884.40
cum
1259.25
cum
1630.00
43
CHAPTER-B5
REPAIR AND REHABILITATION
Item
No.
5.1
5.2
5.3
5.4
5.5
a)
b)
5.6
5.7
5.8
5.9
Descriptions
Removal of existing cement concrete wearing coat including its
disposal complete as per Technical specification without causing any
detrimental effect to any part of the bridge structure and removal of
dismantled material with all lifts and lead upto 1000m(Thickness 75
mm) and as per relevant clauses of section 2800.
Removal of existing asphaltic wearing coat including disposal with all
lift and lead upto 1000m and as per relevant clauses of section 2800.
Guniting concrete surface with 25mm thick (Average) cement mortar
applied with compressor after cleaning surface and spraying with
epoxy complete as per Technical specification and as per relevant
clauses of section 2800.
Providing and inserting nipples with approved fixing compound after
drilling holes for grouting as per Technical specifications including
subsequent cutting/removal and sealing of the hole as necessary of
nipples after completion of grouting with Cement/Epoxy and as per
relevant clauses of section 2800.
Sealing of cracks/porous concrete by injection process through
nipples/Grouting complete as per Technical specification and as per
relevant clauses of section 2800.
Cement Grout
Cement mortar (1:1) Grouting
Patching of damaged concrete surface with 25mm thick (Average)
polymer concrete and curing compounds, initiator and promoter,
available in present formulations, to be applied as per instructions of
manufacturer and as approved by the Engineer and as per relevant
clauses of section 2800.
Sealing of crack / porous concrete with Epoxy Grout by injection
through nipples complete as per clause 2803.1 and as per relevant
clauses of section 2800.
Providing and Applying 10mm thick (Average) epoxy mortar over
leached, honey combed and spalled concrete surface and exposed steel
reinforcement complete as per Technical specification and as per
relevant clauses of section 2800.
Removal of defective concrete, 40mm thick (Average) cleaning the
surface thoroughly, applying the shotcrete mixture mechanically with
compressed air under pressure, comprising of cement, sand, coarse
aggregates, water and quick setting compound in the proportion as per
clause 2807.1., sand and coarse aggregates conforming to IS: 383 and
table 1 of IS: 9012 respectively, water cement ratio ranging from 0.35
to 0.50, density of gunite not less than 2000 kg/cum, strength not less
than 25 Mpa and workmanship conforming to clause 2807.6 and as per
relevant clauses of section 2800.
Unit
Rate (Rs.)
sqm
94.00
sqm
71.00
sqm
1096.00
each
68.00
kg
kg
66.00
61.00
sqm
1773.00
kg
1119.00
sqm
839.00
sqm
274.00
44
Item
No.
5.10
5.11
5.12
5.13
a)
b)
c)
Descriptions
Unit
Rate (Rs.)
116.00
924.00
294303.00
45000.00
55000.00
65000.00
45
Type of work
2.
3.
Type of work
2
3.
Embankments.
Not less than 95
Expansive clays.
(a) Sub-grade and 500mm portion just
Not allowed
below the sub-grade.
(b) Remaining portion of embankment.
Not less than 90
The contractor shall, at least 7 working days before commencement of compaction,
submit the following to the Engineer for approval :
1.
The values of maximum dry density and Optimum Moisture Content obtained in
accordance with IS:2720 (Part 7 or Part 8), as the case may be, appropriate for each
of the fill materials he intends to use.
2.
A graph of density plotted against moisture content from which each of the values in '1.'
above of maximum dry density and Optimum Moisture Content were determined.
3.
The dry density - moisture content - CBR relationship for light, intermediate and heavy
compactive efforts (Light corresponding to IS:2720 (Part 7). Heavy corresponding to
IS:2720 (Part 8) and intermediate in between the two) for each of the fill materials he
intends to use in the sub-grade.
59
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
53 mm
Class I
-
Class III
100
45 mm
97-100
26.5 mm
100
22.4 mm
95-100
58-100
11.2 mm
100
48-100
20-60
5.6 mm
92-100
28-54
4-32
2.8 mm
83-100
20-35
0-10
1.4 mm
59-96
0-5
710 micron
35-80
6-18
355 micron
14-40
2-9
180 micron
3-15
90 micron
0-5
0-4
0-3
Sieve Designation
60
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
IS Sieve Designation
75 mm
53 mm
80-100
100
26.50 mm
55-90
70-100
100
9.50 mm
35-65
50-80
65-95
4.75 mm
25-55
40-65
50-80
2.36 mm
20-40
30-50
40-65
0.425 mm
10-25
15-25
20-35
0.075 mm
3-10
3-10
3-10
30
25
20
IS Sieve Designation
75 mm
53 mm
100
26.50 mm
55-75
50-80
100
9.50 mm
4.75 mm
10-30
15-35
25-45
2.36 mm
0.425 mm
0.075 mm
<10
<10
<10
30
25
20
Note: The materials passing 425 micron (0.425mm) sieve for all the three grading when
tested according to IS:2720 (Part 5) shall have liquid limit and plasticity index not
more than 25% and 6% respectively.
61
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Size Range
IS Sieve Designation
1.
90 mm to 45 mm
125 mm
Percent by weight
passing
100
90 mm
90-100
63 mm
25-60
45 mm
0-15
22.4 mm
0-5
90 mm
100
63 mm
90-100
53 mm
25-75
45 mm
0-15
22.4 mm
0-5
63 mm
100
53 mm
95-100
45 mm
65-90
22.4 mm
0-10
11.2 mm
0-5
2.
3.
63 mm to 45 mm
53 mm to 22.4 mm
Note: The compacted thickness for a layer with Grading I shall be 100 mm while for layer
with other Grading i.e. II & III, it shall be 75 mm.
Size Range
IS Sieve Designation
A.
13.2 mm
13.2 mm
Percent by weight
passing
100
11.2 mm
95-100
5.6 mm
15-35
180 micron
0-10
11.2 mm
100
5.6 mm
90-100
180 micron
15-35
B.
11.2 mm
62
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Size Range
Compacted
thickness
Loose
Quantity
Grading- I
90mm to
45mm
100mm
1.21 to
1.43 m
Screenings
Stone Screemings
Crushable type such as
Moorum or Gravel.
Grading
For WBM
Grading
Loose Qty.
Classificasub-base/
Classifica
tion & size base course
-tion &
(Loose
size
Qty.)
Type A 13.2 0.27 to 0.30
Not
0.30 to 0.32
mm
m
uniform
m
Grading- II
63mm to
45mm
75mm
0.91 to
1.07 m
Type A 13.2
mm
0.12 to 0.15
m
Not
uniform
0.22 to 0.24
m
Grading- II
63mm to
45mm
75mm
0.91 to
1.07 m
Type B 11.2
mm
0.20 to 0.22
m
Not
uniform
0.22 to 0.24
m
Grading- III
53mm to
22.4 mm
75mm
0.91 to
1.07 m
Type B 11.2
mm
0.18 to 0.21
m
Not
uniform
0.22 to 0.24
m
Table 400-10 Physical requirements of coarse aggregate wet mix macadam for sub-base/
base course.
S.No.
1
Test
*Los Angles Abrasion Value
Test Method
IS : 2386 (Part 4)
Requirements
40 percent (Max.)
IS : 2386 (Part 4) or
IS : 5640
30 percent (Max.)
OR
*Aggregate Impact Value
2.
*
**
63
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
IS Sieve
Designation
53.00 mm
Percent by weight
passing the IS Sieve
100
45.00 mm
95-100
26.50 mm
22.40 mm
60-80
11.20 mm
40-60
4.75 mm
25-40
2.36 mm
15-30
600 micron
8-22
75 micron
0-8
64
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Grade - I
Grade - II
40mm
19mm
80-100 mm
50-75 mm
Cumulative % by Weight of total aggregate passing
100
-
37.5
90 - 100
26.5
75 - 100
100
19
90 - 100
13.2
35 - 61
56 - 88
4.75
13 - 22
16 - 36
2.36
4 - 19
4 - 19
0.3
2 - 10
2 - 10
0.075
0-8
0-8
3.1 - 3.4
3.3 - 3.5
Bitumen Grade
35 - 90
35 - 90
Note: 1. Appropriate bitumen contents for conditions in cooler areas of India may be upto
0.5% higher subject to the approval of the Engineer.
Aggregate
Mixing
(C)
160-175
Mixed
Material
(C)
170 Maximum
Rolling
(C)
Laying
(C)
35
Bitumen
Mixing
(C)
160-170
100 Minimum
130 Minimum
65
150-165
150-170
165 Maximum
90 Minimum
125 Minimum
90
140-160
140-165
155 Maximum
80 Minimum
115 Minimum
65
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
IS Sieve
Designation (mm)
63
45
100
58 - 82
26.5
37 - 72
100
22.4
100
5 - 27
50 - 75
13.2
2 - 20
50 - 75
11.2
5 - 25
5.6
5 - 25
2.8
0-5
0-5
0-5
0-5
0.06
0.015
0.09
0.018
Approx. Loose
Aggregate Quantities
cu.m/m
Binder quantity
(penetration grade)1
(kg/m)
6.8
Note: 1. If cutback bitumen is used, adjust binder quantity such that the residual bitumen is
equal to the values in this table.
66
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
IS Sieve Designation
53.0 mm
26.5 mm
40 - 75
22.4 mm
100
13.2 mm
0- 20
40 - 75
5.6 mm
0 - 20
2.8 mm
0-5
0-5
0.3
95 - 100
0.075
85 - 100
67
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
1
2
40 mm
25 mm
80 - 100 mm
50 - 75 mm
Cumulative % by weight of total aggregate passing
100
-
37.5
95 - 100
100
26.5
63 - 93
90 - 100
19
71 - 95
13.2
55 - 75
56 -80
9.5
4.75
38 - 54
38 - 54
2.36
28 - 42
28 - 42
1.18
0.6
0.3
7 - 21
7 - 21
0.15
0.075
2-8
2-8
Min 4.0
Min 4.5
65 or 90
65 or 90
Note: 1.
2.
The combined aggregate grading shall not vary from the low limit on one sieve
to the high limit on the adjacent sieve.
Determined by the Marshall method.
9.0
2
4
75 blows on each of the two faces of the
specimen
3-6
See Table 500 - 12 below
65 - 75
68
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
12.5
13.0
14.0
15.0
19.0
25.0
37.5
12.0
11.0
10.0
13.0
12.0
11.0
14.0
13.0
12.0
Note: 1.
2.
The nominal maximum particle size is one size larger than the first sieve to
retain more than 10 percent.
Interpolate minimum voids in the mineral aggregate (VMA) for design air voids
values between those listed.
Permissible Variation
Base/Binder course
Wearing Course
8%
7%
7%
6%
6%
5%
5%
4%
4%
3%
2%
1.5%
Binder content
0.3%
0.3%
Mixing temperature
10C
10C
69
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
1
2
13 mm
10 mm
35 - 40 mm
25 - 30 mm
Cumulative % by weight of total aggregate passing
-
37.5
26.5
19
100
13.2
90 - 100
100
9.5
70 - 90
90 - 100
4.75
35 - 51
35 - 51
2.36
24 - 39
24 - 39
1.18
15 - 30
15 - 30
0.6
0.3
9 - 19
9 - 19
0.15
0.075
3-8
3-8
Min 4.5
Min 5.00
65*
65*
Note: 1.
2.
*
The combined aggregate grading shall not vary from the low limit on one sieve
to the high limit on the adjacent sieve.
Determined by the Marshall method.
Only in exceptional circumstances, 80 - 100 penetration grade may be used, as
approved by the Engineer.
70
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
8.2
2
4
75 blows on each of the two faces of the
specimen
3-5
See Table 500 - 12 below
65 - 78
1
2
19 mm
13 mm
50 - 65 mm
30 - 45 mm
Cumulative % by weight of total aggregate passing
-
37.5
26.5
100
19
79 - 100
100
13.2
59 - 79
79 - 100
9.5
52 - 72
70 - 88
4.75
35 - 55
53 - 71
2.36
28 - 44
42 - 58
1.18
20 - 34
34 - 48
0.6
15 - 27
26 - 38
0.3
10 - 20
18 - 28
0.15
5 - 13
12 - 20
0.075
2-8
4 - 10
5.00 - 6.00
5.00 - 7.00
65
65
Note: 1.
2.
The combined aggregate grading shall not vary from the low limit on one sieve
to the high limit on the adjacent sieve.
Determined by the Marshall method.
71
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
9.0
2
4
75 blows on each of the two faces of the
specimen
3-6
See Table 500 - 12
65 - 75
Min. 75 percent retained strength.
Note :
1.
2.
3.
19
Chips
Cum/m
0.015
13
1.0
0.010
10
0.9
0.008
0.75
0.004
These rates of spread are for pricing purpose - see clause 510.2.3 and clause 510.8
For emulsion, these rates of spread are for the residual bitumen and appropriate
adjustment must be made to determine the total quantity.
Refer to Manual for Construction and Supervision of Bituminous Works for the
procedure of determining the rates of spread of binder and chips.
72
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
19.0
85 - 100
100
13.2
0 - 40
85 - 100
100
9.5
0-7
0 - 40
85 - 100
100
6.3
0-7
0 - 35
85 - 100
4.75
0 - 10
3.35
0 - 35
2.36
0-2
0-2
0-2
0 - 10
0.60
0-2
0.075
0 - 1.5
0 - 1.5
0 - 1.5
0 - 1.5
Minimum 65%
by weight of
aggregate
Passing 19 mm
retained 13.2mm
Passing 13.2 mm
retained 9.5 mm
Passing 9.5 mm
retained 6.3 mm
Passing 6.3 mm
retained 3.35mm
Slot jets
Min. C
Max. C
Penetration grades
400/500
160
170
140
150
280/320
165
175
150
160
180/200
170
190
155
165
80/100
180
200
165
175
73
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
0.18 m
0.09 m
Total:
0.27 m
9.5 kg.
5.1 kg.
(B)
Premix Carpet
(a) Coarse aggregate nominal 13.2mm size, passing IS
22.4mm sieve and retained on IS 11.2mm sieve
0.18 m
(b)
0.09 m
(A)
Premix Carpet
(B)
12 to 14 kg
10 to 12 kg
74
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Aggregate Gradation
100
88 - 100
5.6 mm
52 - 88
31 - 52
2.8 mm
14 - 38
5 - 25
0.090 mm
0-5
0-5
Table 500-27,
S. No.
(i)
75 mm
Designation of sieve
through which the
aggregates shall wholly
pass
106 mm
Designation of sieve on
which the aggregates
shall be wholly retained
(ii)
63 mm
90 mm
53 mm
(iii)
45 mm
53 mm
26.5 mm
(iv)
26.5 mm
45 mm
22.4 mm
(v)
22.4 mm
26.5 mm
13.2 mm
(vi)
13.2 mm
22.4 mm
11.2 mm
(vii)
11.2 mm
13.2 mm
6.7 mm
(viii)
6.7 mm
11.2 mm
2.8 mm
63 mm
75
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
1.
75 mm and 63 mm
2.
45 mm and 26.5 mm
10.0
3.
5.0
4.
Fine aggregate
5.0
Table 500-29,
Penetration at 25 C
Property
Test method
IS 1203
Requirement
15 5*
Softening point, C
IS 1205
65 10
Max.
IS 1212
2.0
Min.
IS 1216
95
Max
IS 1217
1.0
In cold climatic regions (temperature < 10C), a softer penetration grade of 30/40 may
be used.
Table 500-30,
Application
Thickness
range (mm)
25 - 50
40 - 50
Nominal size of
coarse aggregate
(mm)
13
13
Coarse aggregate
content, % by
mass of total mix
40 10
45 10
13 mm
Cumulative % passing by weight
100
88 - 96
0-5
76
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
S.No.
IS Sieve
Percentage by weight of
aggregate
0 - 25
1.
2.
10 - 30
3.
10 - 30
4.
Passing 0.075 mm
30 - 35
Table 500-32,
S.No.
IS Sieve
Percentage by weight of
aggregate
Minimum
Maximum
0
22
1.
2.
30
3.
18
4.
Passing 0.075 mm
25
45
5.
Bitumen content
14
17
77
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
4.75
90 -100
100
3.35
80 - 100
100
2.36
65 - 90
75 - 100
95 - 100
1.18
45 - 70
55 - 90
70 - 95
0.600
30 - 50
35 - 70
55 - 75
0.300
18 - 30
20 - 45
30 - 50
0.150
10 - 21
10 - 25
10 - 30
0.075
5 - 15
5 - 15
5 - 15
Quantity of residual
binder, percentage by
mass of aggregate
Approximate
Coverage rate (kg/m)
7.5 - 13.5
10 - 16
12 - 20
8 - 15
4-6
2-4
Table 500-41,
78
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Requirement
2.0
2 x 75
3-5
> 16
65 - 75
79
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Designation
Method of
Test
90 to 150
50 to 89
30 - 49
IS:1203-1978
35
22
18
IS:1205-1978
38
48
59
IS:1205-1978
-24
-16
-12
IS:9381-1978
75
50
50
IS:1208-1978
220
220
220
IS:1209-1978
70
60
50
ASTM
(50)**
(40)**
(30)**
D5976-1996
ASTM
D5976-1996
2-6
4-8
IS:1206-1978
Designation
Method of
Test
18
15
12
IS:1203-1978
1.0
1.0
1.0
IS:9382-1979
IS:1205-1978
35
35
35
IS:1203-1978
60
40
35
ASTM
35**
30**
25**
D5976-1996
*
**
80
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Designation
Method of
Test
90 to 150
50 to 89
30 - 49
IS:1203-1978
35
22
18
IS:1205-1978
38
48
59
IS:1205-1978
-20
-15
-10
IS:9381-1978
50
40
30
IS:1208-1978
220
220
220
IS:1209-1978
60
50
40
ASTM
D5976-1996
ASTM
D5976-1996
2-4
4-8
IS:1206-1978
Designation
Penetration at 4C, 0.1mm, 200g, 60 sec.
Minimum*
Loss in Weight, %, Maximum
Method of
Test
18
15
12
IS:1203-1978
1.0
1.0
1.0
IS:9382-1979
IS:1205-1978
35
35
35
IS:1203-1978
45
35
30
ASTM
D5976-1996
81
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Designation
Method of
Test
50 - 70
50 - 60
40 - 60
IS:1203-1978
50
55
60
IS:1205-1978
40
35
30
ASTM
D5976-1996
60
60
60
IS:1203-1978
IS:1205-1978
25
20
15
ASTM
D5976-1996
82
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
1.
Sub-Grade
+ 20mm
- 25mm
2.
Sub-base + 10mm
a) Flexible pavement
- 20mm
b) Concrete Pavement
+ 6mm
- 10mm
+ 6mm
- 6mm
4.
5.
i)
Machine laid
+ 10mm
- 10mm
ii)
Manually laid.
+ 15mm
- 15mm
Machine laid
+ 6mm
- 6mm
ii)
Manually laid.
+ 10mm
- 10mm
+ 5mm
- 6mm*
83
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Irregularity
Length (m)
National
Highways/
Expressway*
Roads of
40
18
4
2
60
27
Lower
category*
*
Category of each section of road as described in the contract.
The maximum allowable difference between the rod surface and underside of a 3m
straight edge when placed parallel with, or at right angles to the center line of the road
at points decided by the Engineer shall be for :
(i)
3mm
(ii)
6mm
(iii)
8mm
(iv)
10mm
84
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
S.
No.
1.
2.
Control tests and their Minimum Frequency for Sub-Bases and Bases
(Excluding bitumen Bound Bases)
Type of
Construction
Granular
Lime/Cement
Stabilised Soil Subbase.
Test
(i)
Gradation
(ii) Atterberg Limits
(iii) Moisture content prior to
compaction
(iv) Density of compacted layer
(v) Deleterious constituents
(vi) CBR
(i)
Quality of Lime/Cement
(ii)
Lime/Cement Content
Water Bound
Macadam.
(i)
(ii) Grading
(iii) Flakiness index and Elongation
index.
(iv) Atterberg limits of binding
material
(v) Atterberg limits of portion of
aggregate passing 425 micron
sieve.
4.
Wet Mix
Macadam.
Frequency (Min.)
(i)
(ii)
(iii)
Grading
Flakiness index and Elongation
index
Atterberg limits of portion of
aggregate passing 425 micron
sieve
Density of compacted layer
(iv)
(v)
85
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
S.
No.
1.
2.
Control tests and their Minimum Frequency for Sub-Bases and Bases
(Excluding bitumen Bound Bases)
Type of
Construction
Primer Coat/ Tack
Coat/For spray
Seal coat/surface
dressing.
Test
Frequency (Min.)
(i)
Quality of binder.
(ii)
(iii)
(i)
Quality of binder
(ii)
(iv)
(v)
---------- do -------------
(vi)
Grading aggregates.
As required.
(ix)
86
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
S.
No.
3.
Control tests and their Minimum Frequency for Sub-Bases and Bases
(Excluding bitumen Bound Bases)
Type of
Construction
Open-graded
premix carpet/ Mix
seal surfacing.
Test
(i)
Quality of binder
(ii)
(iii)
(iv)
(v)
(vi)
Grading aggregates.
(vii)
4.
Bituminous
Macadam
Frequency (Min.)
(x)
(i)
Quality of binder
(ii)
(iii)
(iv)
(v)
Grading of aggregate
(vi)
(vii)
Binder content
87
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Control tests and their Minimum Frequency for Sub-Bases and Bases
(Excluding bitumen Bound Bases)
Type of
Test
Frequency (Min.)
Construction
Bituminous
Penetration
Macadam/Built-up
Spray Grout.
(i)
Quality of binder
(ii)
Dense Bituminous
Macadam/Semi
Dense Bituminous
Concrete/
Bituminous
Concrete.
(i)
Quality of binder
(ii)
(ix)
Mix Grading
(x)
Stability of Mix
88
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Control tests and their Minimum Frequency for Sub-Bases and Bases
(Excluding bitumen Bound Bases)
Type of
Test
Frequency (Min.)
Construction
(xi)
Mastic Asphalt
(i)
Quality of binder
(ii)
(vi)
Grading of aggregates
Hardness number.
89
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
9.
Control tests and their Minimum Frequency for Sub-Bases and Bases
(Excluding bitumen Bound Bases)
Type of
Test
Frequency (Min.)
Construction
Slurry seal
(i)
Quality of binder
(ii)
(i)
Quality of binder
(ii)
As required
(iv)
Plasticity Index
As required
(v)
Mix grading.
(vi)
Stability of Mix.
(ix)
(x)
90
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
S.
No.
10.
Control tests and their Minimum Frequency for Sub-Bases and Bases
(Excluding bitumen Bound Bases)
Type of
Construction
Modified binder
Test
(i)
Softening Point
(ii)
Frequency (Min.)
Initially one submission
thereafter daily if site blended,
weekly if pre-blended.
----------- do ----------
----------- do ----------
(iv)
Ductility
----------- do ----------
(v)
Flash Point
----------- do ----------
(vi)
Fraass Breaking
Initially on submission.
Initially on submission.
Initially on submission.
91
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
a)
b)
c)
Dia in mm
6
Weight Kg/M
0.222
Perimeter Cms.
1.887
0.503
0.395
2.514
10
0.785
0.617
3.143
12
1.131
0.888
3.771
16
2.011
1.578
5.028
18
2.545
2.000
5.657
20
3.142
2.466
6.286
22
3.801
2.984
6.914
25
4.909
3.853
7.857
28
6.157
4.830
8.800
32
8.042
6.313
10.057
40
12.566
9.684
12.571
Dia in mm
3
Weight Kg/M
0.056
Perimeter Cms.
0.943
0.196
0.154
1.571
0.385
0.302
2.200
0.503
0.395
2.514
Weight Kg/M
4.620
3.624
6.036
4.740
1.848
92
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
d)
e)
Size in M.M.
40 x 40 x 6
Weights Kg./M.
3.500
50 x 50 x 6
4.500
75 x 75 x 6
6.800
75 x 75 x 10
11.000
100 x 100 x 6
9.200
100 x 100 x 10
14.900
130 x 130 x 10
19.700
130 x 130 x 12
23.400
Tee
100 x 100 x 10
15.00
Channel
75 x 40 x 6
5.700
Weights Kg./M.
0.00078
2 M.M.
0.00156
3 M.M.
0.00235
6 M.M.
0.00470
10 M.M.
0.00783
12 M.M.
0.00940
20 M.M.
0.01566
25 M.M.
0.01957
93
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Material
Cement
Unit Metric
Cum.
Weights
1440
2.
Steel
a) Mild Steel
b) Cast Steel
c) H.T. Steel
Cu.Cm.
Cu.Cm.
Cu.Cm.
0.0078
0.0078
0.0078
Cu.Cm.
Cu.Cm.
Cu.M.
0.0078
0.0113
2306 to2400
Cum.
Cum.
Cum.
Cum.
Cum.
Cum.
2650
2800
2100
1600
1920
650 to 720
3.
4.
5.
Stainless Steel
Lead
Plain Cement Concrete
or R.C.C.
6.
Stones
a) Lime
b) Sand
Stone Masonry Rubble
Bricks
Brick Masonry
Timber
7.
8.
9.
10.
3.
Conversion Factors.
Top Convert
Inch
Inch
Foot
Mile
Square Inch
Square Foot
Acre
Sq.Mile
Cubic Inch
Cubic Foot
Gallon (Imp.)
Pound
Ton
Lbs. Per Sq. Inch
Ton Per Sq.Foot
To obtain
Into
Millimeter
Centimeter
Meter
Kilometer
Sq.Centimeter
Square Meter
Hectare
Sq.Kilometer
Cu.Centimeter
Cubic Meter
Litre
Kilogram
Tonne
Kg.PerSq.Cm.
Tonne Per Sq.M.
From
Multiply
25.40
2.540
0.3048
1.609
6.4516
0.0929
0.4047
2.590
16.387
0.0283
4.546
0.4536
1.0160
0.0703
10.937
Multiply by
0.039
0.3937
3.2808
0.621
0.155
10.764
2.471
0.386
0.0161
35.3147
0.220
2.2046
0.9842
14.223
0.0914
94
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page
Strength of Concrete
Symbol of concerte
in M. Unit
M - 15
150
M - 20
200
M - 25
250
M - 30
300
M - 35
350
M - 40
400
M - 45
450
NOTE :1)
5.
In Metric Unit
Strength kg./cm
Quantities
0.33 Cum.
1.00 Cum.
0.25 Cum.
1.00 Cum.
0.16 Cum.
1.00 Cum.
1.00 Cum.
0.33 Cum.
1.00 Cum.
0.16 Cum.
1.00 Cum.
0.12 Cum.
0.004 Cum.
0.008 cum.
95
SOR for Road & Bridge works in Public Works Deptt. M.P.
Page