Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
for Windows 7
Users Manual
This manual explains how to install Windows PS Printer Driver and how to use it.
This PS Printer Driver can be used with Microsoft Windows 7.
NOTE:
To use KM-4800w-PS Printer Driver, UG-32B Option License is required.
Index
1.
1.1.
1.2.
1.3.
1.4.
1.5.
2.
INSTALLATION METHOD................................................................................3
Install TCP/IP Port......................................................................................................................................................... 3
Add KM-4800w TCP/IP Port.................................................................................................................................... 7
Add Printer....................................................................................................................................................................11
About Printer Port........................................................................................................................................................18
About reinstall of Printer..............................................................................................................................................20
1.
1.1.
Installation Method
Install TCP/IP Port
NOTE:
If KM-4800wEN printer is already installed on your system, TCP/IP Port
installation has been completed at the same time.
Please go to [1.3 Add Printer] to continue the printer installation.
1. Insert Installation Disk in CD-ROM drive.
2. Open (the optical drive)\ Option\PS_Printer_UG-32\PrinterPort\.
Right-click on KM4800wTcpMon_xxx.exe and select Run as administrator.
(xxx is the version)
4. Click Next.
5. Click Install.
7. Click Finish.
1.2.
7. Click Close.
8. Confirm that KM-4800w TCP/IP Port is displayed in the list. Click Close.
10
1.3.
Add Printer
1.
11
3. Choose Use an existing port: and then select KM-4800w:192.168.100.10 (KM4800w TCP/IP Port) in the pull down menu. Click Next.
12
5. Click Browse.
13
7. Click OK.
8. Click Next.
14
15
11. Check Always trust software from KYOCERA MITA Corporation. and click Install.
16
17
1.4.
18
You do not have to change any of the above settings in usual case.
Change these settings when KM-4800w does not wake up correctly from the Power
Save Mode caused by the network settings.
MAC Address: MAC Address of output printer
Broad Cast Address: An address used to send the data to all PC on the network
Magic Boot Port: Port number to send the data
Timeout: Timeout when no response comes from the output printer
Retry: Number of retry when no response comes from the output printer
19
1.5.
Click Yes.
20
In Devices and Printers, click Fax icon and then click Print server properties.
21
Click Yes.
22
Click Delete.
Click OK.
If the removal of the driver is failed, reboot the PC, and then try to remove the driver
again.
23
Click Close.
24
2.
25
26
<Tray Selection>
<Paper Source>
The source of paper can be selected.
Automatically Select is equivalent to Auto.
<Media>
The type of printing media can be selected.
27
<Paper/Output>
<Paper Size>
Specify the size of paper used for printing.
If Custom Size is selected in the above setting, the following dialog is
indicated.
A paper size can be specified at your option within the following range.
Width: 210 mm to 914.4 mm
Height: 297 mm to 10000 mm
28
<Copy Count>
Number of prints can be specified.
Available count ranges from 1 to 9999 but the guarantee range of proper
operation is from 1 to 999.
Checking Collate enables to print sets with collating.
<Graphic>
<Print Quality>
Printing resolution can be specified.
The printing resolution is normally set to 600dpi.
If there is any problem on a print, the printing resolution can be changed to
300dpi or 200 dpi.
<Scaling>
The printing image is enlarged or reduced according the specified value.
Available percentage ranges from 1 to 1000 but the guarantee range of proper
operation is from 20 to 500.
<True Type Font>
True Type Font options can be specified.
The option is normally set to Substitute with Device Font.
If some special characters are lost or printed incorrectly, set it to Download as
Softfont.
<Document Options>
<Advanced Printing Features>
This option should be always set to Enabled.
<Pages per Sheet Layout>
Page Layout option can be specified for Pages per Sheet.
29
<PostScript Options>
30
31