Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
DECO POP
Doc.-No.: 2197
DATA SHEET
SAP-No.: 1681671
Adhemax Accelerator 1
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
Process Information............................................................................................................................... 2
Equipment and Working Parameters..................................................................................................... 2
Make-Up................................................................................................................................................ 3
Maintenance.......................................................................................................................................... 3
Correction Instruction............................................................................................................................. 3
SAP No. for Make-Up and Maintenance Products.................................................................................3
Recommendations for Wastewater Treatment.......................................................................................4
Analytical Instructions............................................................................................................................ 5
Determination of Sulfuric Acid (96 %) by Titration.............................................................................5
Determination of Adhemax Accelerator 1 by Titration..................................................................7
Page: 1 / 8
Released on:
Released by:
05.08.2011
BTT DECO
Version: 05
Adhemax Accelerator 1
Doc.-No.: 2197
1. Process Information
The purpose of the Adhemax Accelerator 1 is to accelerate the Pd-colloids adsorbed on the
ABS or ABS/PC blend materials plastic surface for electroless metallization and to prevent rack metallization
by stripping off the catalyst specifically from the rack isolation.
Exhaust
Required.
pH
Solution temperature
35 55 C
Treatment time
1 5 min.
Agitation/Air Agitation
Filtration
Page: 2 / 8
Released on:
Released by:
05.08.2011
BTT DECO
Version: 05
Adhemax Accelerator 1
Doc.-No.: 2197
3. Make-Up
Make-Up of 100 l of Adhemax Accelerator 1
DI Water
H2SO4 (conc.)
Adhemax Accelerator 1
Liter
kg
about 97.5
2.25
---
97.5
4.25
6.0
4. Maintenance
A new make-up is recommended after a throughput of about 8 12 m/l. It is also recommended to use
10 20 % of an used Accelerator bath if available. If no used bath is available it might be necessary to use a
higher bath temperature after the new make-up.
5. Correction Instruction
Process solution
Adhemax
Accelerator 1
Component
Adhemax
Accelerator 1
Sulfuric Acid
Working Window
50 70 g/l
20 55 g/l
Lack of
component
Rack metallization /
skip plating
Rack metallization /
skip plating
Excess of
component
Skip plating
Skip plating
SAP No.
ADHEMAX ACCELERATOR 1
1680343
Page: 3 / 8
Released on:
Released by:
05.08.2011
BTT DECO
Version: 05
Adhemax Accelerator 1
Doc.-No.: 2197
Be sure to observe all local regulations concerning the limit values of pollutants
including the general regulations on dangerous materials!!
Page: 4 / 8
Released on:
Released by:
05.08.2011
BTT DECO
Version: 05
Adhemax Accelerator 1
Doc.-No.: 2197
8. Analytical Instructions
Version: 03
Doc.-No.: A0000202-03
Principle:
Acid-base titration.
Reagents required*:
IMPORTANT NOTE: Be sure to observe all local regulations concerning the limiting
values of pollutants including the general regulations on hazardous materials!
Equipment required:
Procedure:
Page: 5 / 8
Released on:
Released by:
05.08.2011
BTT DECO
Version: 05
Adhemax Accelerator 1
Doc.-No.: 2197
The amount of ml 0.1 M Sodium hydroxide-standard solution*** consumed multiplied by 2.78 gives the
content of Sulfuric acid in ml/l.
The amount of ml 0.1 M Sodium hydroxide-standard solution*** consumed multiplied by 4.9 gives the
content of Sulfuric acid in g/l.
Example:
During titration of 1.0 ml of the sample to be tested, 5.5 ml of 0.1 M Sodium hydroxide-standard solution
were used.
Calculation:
5.5 2.78 = 15.13 ml/l Sulfuric acid (96%)
5.5x 4.9 = 26.95 g/l Sulfuric acid
*
**
***
Page: 6 / 8
Released on:
Released by:
05.08.2011
BTT DECO
Version: 05
Adhemax Accelerator 1
Doc.-No.: 2197
Version: 05
Doc.-No.: EXT-1005-TIT-05
DI-water
0.02 M Potassium permanganate-solution (0.1N)
0.1M sodium thiosulfate solution
2.5 M Sulfuric acid-solution (5 N)
30% Potassium iodide
Starch solution 1 %
Please follow the general regulations for hazardous materials in the Material safety
data sheets!
The analytical procedure is to be followed exactly.
Be sure to observe all local regulations concerning the permitted limits for
pollutants.
Procedure:
Page: 7 / 8
Released on:
Released by:
05.08.2011
BTT DECO
Version: 05
Adhemax Accelerator 1
Doc.-No.: 2197
Evaluation:
(ml consumptionblank solution ml consumption sample) 7.40 = Adhemax Accelerator 1 in g/l
Example:
With the blank solution, 20.28 ml, and with a sample, 11.74 ml sodium thiosulfate-volumetric solution*** are
used.
(20.28 11.74) 7.4 = 63.2 g/l Adhemax Accelerator 1
*
**
***
This sheet shall serve for your information. The content of the sheet is based on our best
knowledge. We do not undertake any duty to advise. The contents of the sheet shall not
be considered as an agreement on condition and quality of the goods delivered.
The decision to use our products for its production purposes is the responsibility of our
customer. We can accept liability only for the quality of our products at delivery. If
difficulties arise in the application of our products, we propose that you contact our
technical service department.
Page: 8 / 8
Released on:
Released by:
05.08.2011
BTT DECO