Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Valve Specification
Page
Date
Revision
All
04-May-2012
Changes standard format of document.
All
04-May-2012
was PHEONWJ-X-SPE-0003
All
04-May-2012
All
04-May-2012
Replace PHEONWJ-X-SPE-0004 with PHEONWJ-M-SPE-0024
6 of 67
04-May-2012
8 of 67
04-May-2012
accordingly.
All
04-May-2012
Marking
( Typical revision)
a.
b.
All
04-May-2012
d.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 2 of 46
Valve Specification
Table of Contents
1.
Scope .................................................................................................................................... 4
3.
2.
References ............................................................................................................................ 4
3.1.
Definitions ................................................................................................................... 5
3.2.
Terms .......................................................................................................................... 6
4.
Abbreviations ......................................................................................................................... 6
6.
5.
6.1.
General ....................................................................................................................... 9
6.2.
Flanges ....................................................................................................................... 9
7.
6.3.
Welding Ends .............................................................................................................. 9
Valves .................................................................................................................................. 10
7.1.
7.2.
7.3.
7.4.
7.5.
7.6.
7.7.
7.8.
7.9.
7.10.
7.11.
7.12.
7.13.
7.14.
7.15.
7.16.
7.17.
7.18.
7.19.
7.20.
7.21.
7.22.
7.23.
7.24.
7.25.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 3 of 46
Valve Specification
1. Scope
This specification covers the minimum requirements for the Valves to be installed on the PT.
2. References
API
API
API
API
API
API
API
API
Spec 5L
Spec 6D
Spec 6FA
Spec 6FD
Std 594
Std 598
Std 599
Std 600
Line Pipe
Specification for Pipeline Valves (Gate, Plug, Ball & Check Valves)
Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas
Industries
Extended-Body Ends
Butterfly Valves
ASME
ASME
ASME
ASME
ASME
ASME
B1.20.1
B16.5
B16.25
B16.34
B16.47
B46.1
ASTM A105
ASTM A126
ASTM A182
ASTM A194
ASTM A193
ASTM A216
ASTM A276
ASTM A351
ASTM
ASTM
ASTM
ASTM
B21
B61
B62
B124
ASTM B140
ASTM B148
ASTM B150
ASTM D1784
ASTM D2467
ASTM F439
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Forged or Rolled Alloy Steel Pipe Flanges, Forged Fittings & Valves &
Carbon & Alloy Steel Nuts for Bolts for High Pressure or High
Service
Temperature Service
Castings,
Austenitic,
Austenitic-Ferritic
(Duplex),
for
Pressure-
Containing Parts
Standard Specification for Copper and Copper Alloy Forging Rod, Bar,
and Shapes
Schedule 80
Page 4 of 46
ASTM F1970
Valve Specification
Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl
Chloride) Systems
British Standard
BS EN 593
MSS SP-80
MSS SP-110
Flared Ends
NACE MR0175
NSF/ANSI 61
Health Effects
Company Specifications
3.1. Definitions
- bi-directional Valve
valve designed for blocking the fluid in both downstream and upstream directions
uni-directional Valve
bleed
drain or vent
block valve
gate, plug or ball valve that blocks flow into the downstream conduit when in the closed position
single valve with two seating surfaces that, in the closed position, provides a seal against pressure
from both ends of the valve with a means of venting/bleeding the cavity between the seating
surfaces
single valve with two seating surfaces, each of which, in the closed position, provides a seal
against pressure from a single source, with a means of venting/bleeding the cavity between the
seating surfaces.
Operator
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 5 of 46
Valve Specification
obturator
part of a valve, such as a ball, clapper, disc, gate or plug that is positioned in the flow stream to
stem
part that connects the obturator to the operator and which can consist of one or more components.
3.2. Terms
&
Will
Used normally in connection with an action by PT. PHE ONWJ rather than by a Contractor or Supplier.
May
Should
Shall
Must
4. Abbreviations
- AlBr
Aluminium Bronze
- AISI
American Iron and Steel Institute
- ANSI
American National Standards Institute
- API
American Petroleum Institute
- ASTM
American Society for Testing & Materials
- ASME
American Society of Mechanical Engineers
- BB
Bolted Bonnet
- BC
Bolted Cap
- BE
Bevel End
- BS
British Standard
- BW
Butt Weld
- Cr
Chromium
- CWP
Cold Working Pressure
- DBB
Double Block and Bleed
- DIB
Double Isolation & Bleed
- DIPA-PFA
Diisopropylamine-Perfluoroalkoxy
- DPE
Double Piston Effect
- ENP
Electroless Nickel Plated
- F-Bore
Full Bore
- FE
Flanged End
- FEP
Fluorinated Ethylene Propylene
- FF
Flat Face
- GO
Gear Operated
- Gr
Grade
- HW
Hand Wheel
- LO
Lever Operated
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 6 of 46
Max
Mill
MSS
NACE
NAF
Ni
NPS
NPTF
NPTM
OS & Y
PE
P & ID
PHE ONWJ
PTFE
POE
PVC
R-Bore
RF
RTJ
Scrd
SP
SPE
SS
Std
SW
TFE
WOG
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Valve Specification
Maximum
Nickel
Plain End
Reduced Bore
Raised Face
Screwed
Standard Practice
Stainless Steel
Standard
Socket Weld
Page 7 of 46
Valve Specification
5. General Requirements
5.1
5.2
Valve from stock will be considered since the manufacturing not longer than two (2) years.
Assessment and inspection shall be conducted, to ensure that the valve is still in good condition,
especially for internal trim and elastomeric part. Certificate shall be obtained from third party.
5.3
Ball, Check, Gate and Plug valves shall have valid license of API 6D monogram and other valves
5.4
Valve manufacturing shall be done in origin country. Otherwise, vendor shall provide letter of
guarantee from head quarter/manufacturer. Company recerves right to investigate and visit
factory.
5.5
Any elastomeric seal component in dynamic application must prevent seal extrusion, galvanic
corrosion and sticking that could prevent its efficiency after a long stand period. Elastomeric seal
material shall be explosive decompression resistance grade (AED), for valve rating equal or
5.6
Block valves shall be equiped with closed / open position indicator. Locking device is an optional,
5.7
Valve marking shall be in accordance with API 6D or MSS SP-25 whenever applicable.
5.8
Valve shall be handled and stored as per manufacture recommendation. End protectors mean
hard plastic or other suitable material for cap / cover of both end of valve shall be fitted, to avoid
debrish ingress. Removing protector is not allowed, except for valve installation or inspection.
5.9
Socket weld end valve, normally for size 1 and smaller, shall be provided with pipe nipple, 4
length, schedule to follow line pipe class. Nipple and valve body shall be welded in factory before
valve assembly. The purpose is to protect elastomeric seal material from overheating during
5.10 Valve weight more than 25 kg should be furnished with lifting lug. Valve support is an optional
when required.
5.12 Flow direction indicator shall be cast, stamped, forged or engraved on the valve body for globe
and check valve. The exception shall comply to Standard and Code.
5.13 DIB ball valves (DIB 1 or 2) shall be stamped as per API 6D.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 8 of 46
Valve Specification
6. End Connections
6.1. General
Valve end connections that connected to equipment shall also comply with the requirements
- Valve end connections shall be in accordance with General Piping Design Specification Doc
No. PHEONWJ-M-SPE-0024
6.2. Flanges
Class 900# flanges & below shall be RF, except where specified otherwise on the
Piping Class Data Sheets or P & IDs. Class 1500# flanges & above shall be RTJ.
Pressure / Temperature ratings of flanges " NPS through 24" NPS are based on the
Flange facings shall be in accordance with ASME B16.5 for RF, FF & RTJ.
Flange gasket surface finishes shall be in accordance with ASME B46.1 & B16.5 & the
following:
Class 150 FF
Serrated finish, roughness between Ra 6.3 &
Ra 1.6 m
BE shall conform to ASME B16.25 / API 5L. PE shall be cut square to the pipe longitudinal axis.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 9 of 46
Valve Specification
7. Valves
7.1.
Valve
Group A
Service
Class
Working
Test & Inspection
Painting
:
:
:
:
Marking
Note
a. Gate Valve
:
:
A1R; Size
Certain size for Potable Water (Outside Quarters), Fire Water, Utility &
150# - ANSI
Metal Surface
For 1
/
& larger
150#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceable
wedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced Wedge,
A105 + HF Stellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HW
operated; GO for 14" & larger or for smaller sizes when recommended by the
manufacturer; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API
6FA.
b. Ball Valve
A2R; Size
150#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI
4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ball for
up to 4; Trunnion mounted for 6 & larger; LO for 4 & smaller; GO for 6" & larger or for
smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &
A2R
& Larger
DIB2S; Size 2
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; Anti
Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;
AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; LO for 4 &
smaller; GO for 6" & larger or for smaller sizes when recommended by the Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
A2R
DIB2M; Size 2
& Larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated; LO
& smaller; GO for 4 & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A
(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; Thermoplastic,
for 3
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 10 of 46
Valve Specification
d. Plug Valve
A3R; Size
& larger
150#; RF; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,
inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCB
body & Cover; ASTM A105 + 3 mils ENP plug; Reinforced PTFE seats; AISI 4140 stem;
LO; GO for 8" & larger or smaller when recommended by the Manufacturer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.
e. Globe Valve
f.
A4R; Size
& Larger
150#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;
ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HF
Stellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HW operated; GO for
8 & larger or smaller when recommended by the Manufacturer; Body disc guide for 8 &
larger; Designed to API 600; Test & Inspection refer to API 598; Fire Test to API 6FA.
Check Valve
A5R; Size
2 & larger
150#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body &
cap; A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite Seat; ASTM A182 F304
hinge pin; ASTM A216 WCB hinge; Designed to API 6D, Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 8 & larger or smaller when recommended by
the Manufacturer.
A5RW; Size
2 & larger
150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Tested to API 6FD; Lifting lug for size 8 &
larger or smaller when recommended by the Manufacturer. (Note: Wafer check should
A5RW1; Size
2 & larger
150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,
Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;
Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for
size 8 & larger or smaller when recommended by the Manufacturer. (Note: Wafer checks
A5RW2; Size
2-12
150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torque
spring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 8 & larger or smaller when recommended by the Manufacturer. (Note:
A5RW4; Size
2 & larger
150#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body; Monel
plates, seat, stop pin, pin retainer and hinge pin; Inconel X-750 spring; Designed to API
6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for size 8 & larger
or smaller when recommended by the Manufacturer. (Note: Wafer checks should only be
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 11 of 46
Valve Specification
g. Butterfly Valve
A7R; Size
2 & larger
150#; Lug type; Replaceable disc & seat; ASTM A216 WCB or ASTM A105 body, bonnet
& disc; 3 mils ENP trim; Shaft ASTM A276 Type 410; Viton seat; Lockable LO; GO for 12"
& larger or for smaller sizes when recommended by the Manufacturer; Designed to API
609; Fire safe designed BS EN 593. Tested & Inspected to API 598.
7.2.
Valve
Group B
Service
Class
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
a. Gate Valve
:
:
B1R; Size
Process hydrocarbon
300# - ANSI
Metal Surface
For 1
/
& larger
300#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceable
wedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced Wedge,
A105 + HF Stellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HW
operated; GO for 14" & larger or for smaller sizes when recommended by the
manufacturer; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API
6FA.
b. Ball Valve
B2R;
300#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI
4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ball for
up to 4; Trunnion mounted for 6 & larger; LO for 4 & smaller; GO for 6" & larger or for
smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &
B2R
& Larger
DIB2S; Size 2
300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; Anti
Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;
AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; LO for 4 &
smaller; GO for 6" & larger or for smaller sizes when recommended by the Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
B2R
DIB2M; Size 2
& Larger
300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated; LO
& smaller; GO for 4 & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A
(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; Thermoplastic,
for 3
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 12 of 46
Valve Specification
d. Plug Valve
B3R;
300#; RF; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,
inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCB
body & cover; ASTM A105 + 3 mils ENP plug; Reinforced PTFE seats; AISI 4140 stem;
LO; GO for 8" & larger or smaller when recommended by the Manufacturer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.
e. Globe Valve
f.
B4R;
300#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;
ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HF
Stellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HW operated; GO for
8 & larger or smaller when recommended by the Manufacturer; Body disc guide for 8 &
larger; Designed to API 600; Test & Inspection refer to API 598; Fire Test to API 6FA.
Check Valve
B5R;
300#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body &
cap; A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite Seats; ASTM A182 F304
hinge pin; ASTM A216 WCB hinge; Designed to API 6D, Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 4 & larger or smaller when recommended by
the Manufacturer.
B5RW;
300#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Tested to API 6FD; Lifting lug for size 4 &
larger or smaller when recommended by the Manufacturer. (Note: Wafer check should
B5RW1;
300#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,
Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;
Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for
size 4 & larger or smaller when recommended by the Manufacturer. (Note: Wafer check
300#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body & Plate;
A105 + HF Stellite Seat; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pin
retainer; Stellite internal valve coating; Designed to API 6D; Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 4 & larger or smaller when recommended by
the Manufacturer. (Note: Wafer check should only be used where space limitations
dictate).
B5RW3;
Size 2 -12
300#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torque
spring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 4 & larger or smaller when recommended by the Manufacturer. (Note:
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 13 of 46
Valve Specification
g. Butterfly Valve
B7R;
300#; Lug type; Replaceable disc & seat; ASTM A216 WCB or ASTM A105 body, bonnet
& disc; 3 mils ENP trim; Shaft ASTM A276 Type 410; Viton seat; Lockable LO; GO for 12"
& larger or for smaller sizes when recommended by the Manufacturer; Designed to API
609; Fire safe designed BS EN 593. Tested & Inspected to API 598.Ball Valve
7.3.
Valve
Group D
Service
Class
Working
Test & Inspection
Painting
:
:
:
:
Marking
a. Gate Valve
D1S; Size 1-
Process Hydrocarbon
Certain size for fire water, utility & salt water, open drain, closed drain,
pressure drain
600# - ANSI
Metal Surface
800#; Scrd ends; BB; OS & Y; Rising stem; Solid wedge; HW operated; ASTM A105 body
& bonnet; A182 F6 (11.5-13.5% Cr) wedge and seats ring, A276 Type 410 stem; Flexible
Graphite NAF packing; Designed to API 602; Test & Inspection refer to API 598; Fire Test
to API 607.
D1Z; Size 1-
& smaller
800#; SW ends; BB; OS & Y; Rising stem; Solid wedge; HW operated; ASTM A105 body
& bonnet; A182 F6 (11.5-13.5% Cr) faced wedge and seats ring, A276 Type 410 stem;
Flexible Graphite NAF packing; Designed to API 602; Test & Inspection refer API 598; Fire
D1R;
600#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceable
wedge & seat; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced wedge,
A105 + HF Stellite seat ring, A276 Type 410 stem; Flexible Graphite NAF packing; HW
operated; GO for 8" & larger or for smaller sizes when recommended by the manufacturer;
Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.
b. Ball Valve
D2S; Size 1-
800#; Min. seat rating 1500# CWP; Scrd ends; BB; F-Bore; Floating ball; LO; Replaceable
ball & seats; ASTM A105 Body & Bonnet; ASTM A182 F6 ball, A276 Type 410 stem;
Thermoplastic, Reinforced PTFE seats; Designed to API 608; Test & Inspection refer to
D2Z; Size 1-
& smaller
800#; Min. seat rating 1500# CWP; SW ends; BB; F-bore; Floating ball; LO; Replaceable
ball & seats; ASTM A105 body & bonnet; ASTM A182 F6 ball; A276 Type 410 stem;
Thermoplastic, Reinforced PTFE seats; Designed to API 608; Test & Inspection refer to
800#; Min. seat rating 1500# CWP; Scrd end x SW end; BB; F-bore; Floating ball; LO;
Replaceable ball & seats; ASTM A105 body & bonnet; ASTM A182 F6 ball; A276 Type
410 stem; Thermoplastic, Reinforced PTFE seats; Designed to API 608; Tested &
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 14 of 46
Valve Specification
D2R;
600#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI
material Anti Explosive Decompression (AED) grade; Floating ball for up to 3 ; Trunnion
mounted for 4 & larger; LO for 3 & smaller; GO for 4" & larger or for smaller sizes when
recommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API
D2R
& Larger
DIB2S; Size 2
600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; Anti
Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;
AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Elastomeric
material Anti Explosive Decompression (AED) grade; LO for 3 & smaller; G O for 4" &
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
D2R
DIB2M; Size 2
& Larger
600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;
GO; ASTM A216 WCB body & bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten Carbide
Coated ball & seats; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
d. Plug Valve
D3S; Size 1-
800#; Scrd Ends; Bolted cover; Lubricated (unless otherwise noted); regular pattern;
pressure balanced; replaceable plug & seat; ASTM A105 body & cover; ASTM A182 F6
plug, Reinforced PTFE seats, AISI 4140 stem; LO; Designed to API 599; Test &
D3Z; Size 1-
& smaller
800#, SW Ends; Bolted cover; Lubricated (unless otherwise noted); Regular pattern;
Pressure balanced; Replaceable plug & seat; ASTM A105 body & cover; ASTM A182 F6
plug, Reinforced PTFE seats, AISI 4140 stem; LO; Designed to API 599; Test &
D3R;
600#; RF; FE; Bolted Cover; Lubricated (unless otherwise noted); Pressure balanced,
inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCB
body & cover; ASTM A105 + 3 mils ENP plug; Reinforced PTFE seats; AISI 4140 stem;
LO; GO for 4" & larger or smaller when recommended by the Manufacturer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.
e. Globe Valve
800#; Scrd Ends; R-Bore; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable
disc & seat; ASTM A105 body & bonnet; A182 F6 (11.5-13.5% Cr) faced disc and seats
ring, A276 Type 410 stem; Flexible Graphite NAF Packing; HW operated; Designed to API
602; Test & Inspection refer to API 598; Fire Test to API 607.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 15 of 46
Valve Specification
800#; SW Ends; R-Bore; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable
disc & seat; ASTM A105 body & bonnet; A182 F6 (11.5-13.5% Cr) faced disc and seats
ring, A276 Type 410 stem; Flexible Graphite NAF Packing; HW Operated; Designed to
API 602; Test & Inspection refer to API 598; Fire Test to API 607.
f.
D4R;
600#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;
ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HF
Stellite Seats, A276 Type 410 Stem; Flexible Graphite NAF packing; HW operated; GO for
6 & larger or smaller when recommended by the Manufacturer; Body disc guide for 8 &
larger; Designed to API 600; Test & Inspection refer to API 598; Fire Test to API 6FA.
Check Valve
D5S; Size 1-
&
800#; Scrd ends; Horizontal swing; BC; Replaceable disc & seat; ASTM A105 body &
bonnet; Chromium Steel A 182-F6A (11.5 - 13.5% Cr) disc, seat & pin; Designed &
D5Z; Size 1-
& smaller
800#; SW ends; Horizontal swing; BC; Replaceable disc & seat; ASTM A105 body &
bonnet; Chromium Steel A 182-F6A (11.5 - 13.5% Cr) disc, seat & pin; Designed &
D5R;
600#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body &
cap; A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite Seat; ASTM A182 F304
hinge pin; ASTM A216 WCB hinge; Designed to API 6D, Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 4 & larger or smaller when recommended by
the Manufacturer.
D5RW;
600#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Tested to API 6FD; Lifting lug for size 4 &
larger or smaller when recommended by the Manufacturer. (Note: Wafer check should
D5RW1;
600#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,
Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;
Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for
size 4 & larger or smaller when recommended by the Manufacturer. (Note: Wafer check
600#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body & Plate;
A105 + HF Stellite Seat; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pin
retainer; Stellite internal valve coating; Designed to API 6D; Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 4 & larger or smaller when recommend ed by
the Manufacturer. (Note: Wafer check should only be used where space limitations
dictate).
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 16 of 46
Valve Specification
D5RW3;
Size 2 12
600#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torque
spring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 4 & larger or smaller when recommended by the Manufacturer. (Note:
7.4.
Valve
Group E
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
a. Gate Valve
:
:
E1R;
Process Hydrocarbon
900# - ANSI
Metal Surface
For 1
/
900#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceable
wedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced wedge,
A105 + HF Stellite seats ring, A276 Type 410 stem; Flexible Graphite NAF packing; HW
operated; GO for 6" & larger or for smaller sizes when recommended by the manufacturer;
Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.
b. Ball Valve
E2R;
900#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI
4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric
material Anti Explosive Decompression (AED) grade; Floating ball for up to 3 ; Trunnion
mounted for 4 & larger; LO for 3 & smaller; GO for 4" & larger or for smaller sizes when
recommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API
E2R
DIB2S; Size 2
& Larger
900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; Anti
Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;
AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric
material Anti Explosive Decompression (AED) grade; LO for 3 & smaller; G O for 4" &
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
E2R
DIB2M; Size 2
& Larger
900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;
GO; ASTM A216 WCB body & bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten Carbide
Coated ball & seats; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 17 of 46
Valve Specification
d. Plug Valve
E3R; Size
2 & larger
900#; RF; FE; R-Bore; Bolted cover, Lubricated (unless otherwise noted); pressure
balanced, inverted independent & adjustable plug; Replaceable plug & seat; ASTM A216
WCB body & cover; ASTM A105 + 3 mils ENP plug & seats; AISI 4140 stem; LO; GO for
4" & larger or for smaller sizes when recommended by the manufacturer; Designed to API
e. Globe Valve
E4R;
900#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;
ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HF
Stellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HW operated; GO for
6 & larger or smaller when recommended by the Manufacturer; Body disc guide for 8 &
larger; Designed to API 600; Test & Inspection refer to API 598; Fire Test to API 6FA.
f.
Check Valve
E5R;
900#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body &
cap; A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite Seat; ASTM A182 F304
hinge pin; ASTM A216 WCB hinge; Designed to API 6D, Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 4 & larger or smaller when recommended by
the Manufacturer.
E5RW;
900#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Tested to API 6FD; Lifting lug for size 4 &
larger or smaller when recommended by the Manufacturer. (Note: Wafer check should
E5RW1;
900#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,
Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;
Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for
size 4 & larger or smaller when recommended by the Manufacturer. (Note: Wafer check
900#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body & Plate;
A105 + HF Stellite Seat; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pin
retainer; Stellite internal valve coating; Designed to API 6D; Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 4 & larger or smaller when recommended by
the Manufacturer. (Note: Wafer check should only be used where space limitations
dictate).
E5RW3;
Size 2 12
900#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torque
spring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 4 & larger or smaller when recommended by the Manufacturer. (Note:
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 18 of 46
Valve Specification
7.5. Valve
Group F
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Gate Valve
F1Z; Size 1-
Process Hydrocarbon
1500# - ANSI
Metal Surface
& smaller
1500#; SW ends; BB; OS & Y; Rising stem; Solid wedge; HW operated; ASTM A105 body
& bonnet; A182 F6 (11.5-13.5% Cr) faced wedge and seats ring, A276 Type 410 stem;
Flexible Graphite NAF packing; Designed to API 602; Test & Inspection refer API 598; Fire
F1J; Size
& larger
1500#; RTJ; FE; BB; OS & Y; Rising stem, plain or flexible type solid wedge; ASTM A216
WCB body & bonnet; A105 + 11.5-13.5% Cr faced wedge, A105 + HF Stellite seat ring,
A276 Type 410 stem; Flexible Graphite NAF packing; HW operated; GO for 4"& larger or
for smaller sizes when recommended by the manufacturer; Designed to API 6D; Test &
b. Ball Valve
F2Z; Size 1-
& smaller
1500#; Min. seat rating 3705# CWP; SW ends; BB; F-bore; Floating ball; LO; Replaceable
ball & seats; ASTM A105 body & bonnet; ASTM A182 F6 (11.5-13.5% Cr) ball, A276
Type 410 stem; Thermoplastic, Reinforced PTFE seats; Designed to API 608; Test &
F2ZOS; Size 1-
& smaller
1500#; Min. seat rating 3705# CWP; Scrd end x SW end; BB; F-bore; Floating ball; LO;
Replaceable ball & seats; ASTM A105 body & bonnet; ASTM A182 F6 (11.5-13.5% Cr)
ball, A276 Type 410; Thermoplastic, Reinforced PTFE seats; Designed to API 608; Tested
F2J;
1500#; RTJ; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI
4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric
material Anti Explosive Decompression (AED) grade; Floating ball for up to 2 ; Trunnion
mounted for 3 & larger; LO for 3 & smaller; GO for 4" & larger or for smaller sizes when
recommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API
F2J
DIB2S; Size 2
& Larger
1500#; RTJ; FE; B B; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated;
Anti Static; ASTM A216 W CB body & bonnet; ASTM A105 + 3 m ils ENP ball & seats
retainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;
Elastomeric material Anti Explosive Decompression (AED) grade; LO for 3 & smaller; GO
for 4" & larger or for smaller sizes when recommended by the Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 19 of 46
Valve Specification
F2J
DIB2M; Size 2
& Larger
1500#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;
GO; ASTM A216 WCB body & bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten Carbide
Coated ball & seats; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
d. Plug Valve
F3Z; Size 1-
& smaller
1500#; SW Ends; Bolted cover; Lubricated (unless otherwise noted); regular pattern;
Pressure balanced; Replaceable plug & seat; ASTM A105 body & cover; ASTM A182 F6
plug, Reinforced PTFE seats, AISI 4140 stem; Designed to API 599; Test and Inspection
F3J; Size
2 & larger
1500#; RTJ; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,
inverted independent & adjustable plug; Replaceable plug & seat; ASTM A216 WCB body
& cover; ASTM A105 3 mills ENP plug and seats; AISI 4140 stem; LO; GO for 4" & larger
or for smaller sizes recommended by the manufacturer; Designed to API 6D; Test &
e. Globe Valve
F4Z; Size 1-
& smaller
1500#; SW Ends; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable disc &
seat; ASTM A105 body & bonnet; A182 F6 (11-13.5% Cr) faced disc and seat ring, A276
Type 410 stem; Flexible Graphite NAF packing; HW operated; Designed to API 602;
F4J; Size
2 & larger
1500#; RTJ; FE; R-Bore; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable
disc & seat; ASTM A216 WCB body & bonnet; A105 + 13.5% Cr faced disc, A105 + HF
Stellite seat ring, A276 Type 410 stem; Flexible Graphite NAF packing; HW operated; GO
for 4" & larger or for smaller sizes when recommended by the Manufacturer; Body disc
guide for 8 & larger; Designed to API 600; Tested & Inspected refer to API 598; Fire
f. Check Valve
F5Z; Size 1-
& smaller
1500#; SW ends, Horizontal swing; BC; Replaceable disc & seat; ASTM A105 body & cap;
11.5% - 13.5% Cr disc, seat & pin; Designed Inspection & Testing to API 602.
F5J; Size
& larger
1500#; RTJ; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body,
cap & hinge; A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite seat; ASTM A182
F304 hinge pin; Designed & Tested refer to API 6D; Fire Tested to API 6FD; Lifting lug for
F5JW; Size
& larger
1500#; RTJ; Wafer; Non-Slam; Replaceable plates & springs; ASTM A216 WCB body
plates & seal; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;
Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size 8 & larger or
smaller when recommended by the Manufacturer. (Note: Wafer checks should only be
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 20 of 46
Valve Specification
F5JW1; Size
2 & larger
1500#; RTJ; Wafer; Non-Slam; Replaceable plates & springs; ASTM A216 WCB body
plates & seal; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Viton
seats; Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size 8 & larger
or smaller when recommended by the Manufacturer. (Note: Wafer checks should only be
F5JW2; Size
& larger
1500#; RTJ; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body
plates & seal; Stellited seats & internal valve (welding overlays with stellite, welding
procedures shall be approved by PHE); 316 SS hinge pin; Inconel X-750 spring; steel stop
pin & pin retainer; Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size
8 & larger or smaller when recommended by the Manufacturer. (Note: Wafer checks
F5JW3;
Size 2 - 12
1500#; RTJ; Wafer; Non-slam; replaceable plates & springs; ASTM A216 WCB body plates
& seal; 316 SS hinge pin; Inconel X-750 Spring; High torque spring; Steel stop pin & pin
retainer; Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size 8 &
larger or smaller when recommended by the manufacturer. (Note: Wafer checks should
7.6.
Valve
Group H
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Ball Valve
H2Z; Size
150# WOG
API 598
Metal Surface
Refer to MSS-SP-25
3 smaller
150# W OG; SW (solvent cement jointed); Socket ends to conform to ASTM D2467 &
ASTM F439; F-bore; LO; Double union design; PVC Type 1 Grade 1 (ASTM D1784) body,
stem, round handle/lever, ball, & union nut; PTFE seat; Viton O-ring seals; Certified per
requirement.
H2F; Size
150# W OG; FF; FE (ASME B16.5); single end entry design; F-bore; LO; PVC Type 1
Grade 1 (ASTM D1784) body, stem, lever & ball; Viton 0-ring seals; Teflon seats; Certified
requirement.
b. Check Valve
H5Z; Size
3 smaller
150# WOG; FF; SW (solvent cement jointed); Socket ends to conform to ASTM D2467 &
ASTM F439; Single end entry design; F-bore; PVC Type 1 Grade 1 (ASTM D1784) body,
stem, lever & ball; Viton 0-ring seals; Teflon seats; Certified per ASTM F1970;
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 21 of 46
Valve Specification
7.7.
Valve
Group J
Service
Rating
Working
:
:
:
:
Marking
:
a. Needle Valve
J6S; Size
(water
2
saturated) process hydrocarbon & pressure drain.
150# - 1500#
line class)
API 598
Metal Surface
Refer to MSS-SP-25
& smaller
6000#; Globe body; Scrd ends (NPTF x NPTF); Scrd bonnet; Inside screw; Rising Stem;
Handle operated; 316 SS body, bonnet, stem, disc & seat; Metal to metal seat;
7.8.
Valve
Group K
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
Marking
a. Gate Valve
K1S; Size
Potable water (outside living quarter), fire water, utility & salt water,
150#
API 598
Metal Surface
Refer to MSS-SP-25
2 & smaller
250#; Scrd ends; BB; Rising stem; Plain or flex type solid wedge; Replaceable seats; Cast
Bronze ASTM B62 Alloy 836 body & bonnet; Bronze or AlBr ASTM B150 Alloy 630 stem;
No. 49 Nickel Alloy disc.; Graphited NAF Packing; HW operated; Designed to MSS SP-80;
b. Ball Valve
K2S; Size
2 & smaller
250#; F-Bore; Scrd ends; BB; Replaceable ball & seats; Cast bronze ASTM B61 body &
tail piece; Brass ASTM B21 stem & ball; Teflon or reinforced Teflon or reinforced Viton
seats & stem seals; LO; Designed to MSS SP-110; Tested to API 598.
c. Globe Valve
K4S; Size
& smaller
250#; Scrd ends; Rising stem; Union bonnet; Replaceable plug disc & seat; HW operated;
Cast Bronze ASTM B62 Alloy 836 body & bonnet; 13% Cr ASTM A182 F6 seat ring; No.
49 Nickel Alloy Disc; AlBr ASTM B150 Alloy 630 stem; Graphite NAF packing; Designed to
d. Check Valve
K5S; Size
& smaller
250#; Scrd ends; Horizontal swing; Re-grind-able disc & disc seat; Scrd cap; Cast Bronze
ASTM B62 Alloy 836 body; Manganese bronze ASTM B128 Alloy 675 cap; Bronze trim;
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 22 of 46
Valve Specification
K5SL; Size
& smaller
250#; Scrd ends; Vertical lift; Re-grind-able disc & disc seat; Scrd cap; Cast Bronze ASTM
B62 Alloy 836 body; Manganese Bronze ASTM B128 Alloy 675 Cap; Bronze trim;
7.9.
Valve
Group P
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Gate Valve
P1X; Size
N/A
API 598
Metal Surface
Refer to MSS-SP-25
& smaller
125# CWP; R-Bore; Solder ends; Union bonnet; Inside screw; Rising stem; Solid wedge;
Cast Bronze ASTM B61 body & bonnet, wedge & seats; Bronze rod stem; Manufacturer's
P1U; Size
- 2
125# CWP; R-Bore; Union ends; Union bonnet; Inside screw; Rising stem; Solid wedge;
Cast bronze ASTM B61 body & bonnet, stem, wedge & seats; Bronze rod stem;
598.
b. Ball Valve
P2UF; Size
& smaller
125# CWP; F-Bore; Union ends; Union bonnet; Replaceable ball & seats; Cast Bronze
ASTM B61 body & bonnet, stem, & ball; Teflon or Reinforced Teflon or reinforced Viton
c. Globe Valve
P4X; Size
&
smaller
125# CWP; R-Bore; Solder ends; Union bonnet; Inside screw; Rising stem; Plug or semi-
plug disc; Replaceable disc & seat; Cast Bronze ASTM B61 body & bonnet, stem, disc &
API 598.
P4U; Size
- 2
125# CWP; R-Bore; Union ends; Union bonnet; Inside screw; Rising stem; plug or semi-
plug disc; Replaceable disc & seat; Cast Bronze ASTM B61 body & bonnet, stem, disc &
API 598.
d. Check Valve
P5X; Size
smaller
&
125# CWP; Horizontal swing; Solder ends; Union bonnet; replaceable disc & seat; Cast
Bronze ASTM B61 body, bonnet, disc & seat; ASTM B140 hinge pin; Designed to MSS
P5XL; Size
smaller
&
125# CWP; Horizontal lift; Solder ends; Union bonnet; Replaceable disc & seat; Cast
bronze ASTM B61 body, bonnet, disc, & seat; ASTM B140 hinge pin; Designed to MSS
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 23 of 46
Valve Specification
P5U; Size
1 - 2
125# CWP; Horizontal swing; Union ends; Union bonnet; Replaceable disc & seat; Cast
bronze ASTM B61 body, bonnet, disc & seat; ASTM B140 hinge pin; Designed to MSS
P5UL; Size
smaller
&
125# CWP, Horizontal lift; Union ends; Union bonnet; Replaceable disc & seat; Cast
bronze (ASTM B61) body, bonnet, disc & seat; ASTM B140 hinge pin; Designed to MSS
7.10. Valve
Group S
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Ball Valve
S2S; Size
N/A
API 598
Metal Surface
Refer to MSS-SP-25
& smaller
(ASTM A182 F 316 SS) body & bonnet; 316 SS ball & trim, Teflon or reinforced
S2T; Size
& smaller
(ASTM A182 F 316 SS) body, stem, ball & trim; PTFE reinforced Teflon seat; Fire
b. Plug Valve
S3S; Size
& smaller
316 SS body, PTFE coated 316 SS plug, Teflon or Viton reinforced O-Ring seals,
LO; Designed to API 599; Test & inspection API 598; Fire tested to API 607.
S3T; Size
& smaller
through 316 SS Body, PTFE coated 316 SS Plug, Teflon or Viton reinforced O-
Ring Seals, LO; Designed to API 599; Test & inspection API 598; Fire tested to API
607.
c. Check Valve
S5S; Size
& smaller
Bolted cover; Replaceable seat & disc ring, SS (ASTM A351 Gr. CF8) body &
bonnet; 11.5-13.5% Cr steel disc & seat ring; Designed to API 602; Tested to API
598.
S5T; Size
& smaller
valve, 316SS Body, poppet nuts & ferrules, Type 302SS spring; TFE Gasket; Viton
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 24 of 46
Valve Specification
S5H; Size
& smaller
valve; 316SS body & poppet; 302SS spring, Viton O-Ring; Designed to API 602;
d. Needle Valve
S6S; Size
& smaller
valves; Handle operated; 316SS body & stem, Union bonnet, TFE Packing.
S6T; Size
& smaller
stem valves; Handle operated; 316SS body & stem; Union bonnet; TFE packing.
7.11. Valve
Group T
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
Marking
a. Gate Valve
jet fuel
150#
API 598
Metal Surface
Refer to MSS-SP-25
T1Z; Size 1-
& smaller
600#; SW; BB; OS & Y; Rising stem; Plain or flex type solid wedge; HW operated; SS
ASTM A351 GR. CF8M body & bonnet; ASTM A276 Type 316 stem & seat ring, Teflon
packing; Designed to API 602; Tested & Inspected to API 598; Fire safe to API 6FA.
T1R; Size
2 & larger
150#; RF; FE; BB; OS & Y; Rising stem; Plain or flex type solid wedge; Replaceable
wedge & seat rings; HW operated; SS ASTM A351 CF8M body, bonnet & wedge; ASTM
A276 Type 316 stem & seat rings; Teflon or reinforced Teflon or reinforced Viton packing;
Designed to API 6D; Tested & Inspected to API 598; Fire safe to API 6FA.
b. Ball Valve
T2Z; Size 1-
& smaller
600# min; Seat rating 1500# CWP; F-Bore; Floating ball; SW; BB; Replaceable ball &
seats; SS ASTM A182 F316 body, cover, stem & ball; Teflon or reinforced Teflon or
reinforced Viton seats; Lever/Handle operated; Designed to API 608; Tested & Inspected
T2R; Size
& larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; SS ASTM A351 CF8M body,
bonnet & ball ASTM A276 Type 316 stem; Teflon or reinforced Teflon or reinforced Viton
packing; LO; Designed to API 6D; Tested and Inspected to API 598; Fire Tested to API
6FA.
c. Globe Valve
T4Z; Size 1-
& smaller
600#; SW; Regular port; BB; OS & Y; Rising stem; Replaceable plug disc & seat ring;
HW operated; ASTM A351 CF8M body & bonnet; ASTM A276 type 316 stem, disc & seat
ring; Teflon packing; Designed to API 602; Tested & Inspected to API 598; Fire Tested to
API 607.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 25 of 46
Valve Specification
T4R; Size
2 & larger
150#; RF; FE; BB; OS & Y; Rising stem; Replaceable plug or semi-plug disc & seat; HW
operated; ASTM A351 CF8M body & bonnet; ASTM A276 Type 316 stem, disc & seat
ring; Teflon or reinforced teflon or reinforced Viton packing; Designed to API 600; Test &
d. Check Valve
T5Z; Size 1-
& smaller
600#; SW; Horizontal swing; BC; Replaceable disc; ASTM A351 CF8M body & bonnet
cap; ASTM A256 type 316 hinge pin & disc; Teflon bonnet Gasket; Designed to API 602;
T5R; Size
& larger
150#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A351 CF8M body;
Cap & disc; ASTM A182 F316 seat ring, hinge; Reinforced teflon or reinforced Viton
bonnet gasket; Designed to API 6D; Test & Inspect API 598; Fire Tested to API 6FD.
7.12. Valve
Group V
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Ball valves
V2S; Size
150#
Metal Surface
Std port; NPTF; Minimum working pressure (rated) 400 psig at l00
F; AlBr body, ball &
stem; LO; AlBr ASTM B148 alloy 958 or equal body ball & stem; PTFE or Buna-N seals &
packing; Designed to API 608; Tested to API 598; Fire safe to API 607.
b. Check valves
V5F; Size
2-12
150#; Wafer; Dual plate; Cast iron ASTM A126 class B or AlBr ASTM B148 alloy 958
body; AlBr ASTM B148 alloy 958 or Monel 400 plate; Spring Monel; Monel or 316 SS
hinge pin; Seals Buna-N or equal; Designed to API 594; Test & Inspection API 598; Fire
c. Butterfly valves
V7FW; Size
2-12
Martensitic stainless steel; Monel shaft; Aluminum bronze or filled PTFE bearings; Nitril
rubber or equal seats; Lockable LO; GO for 8 and larger; Design, dimensions,
manufacture, Tested & Marked to MSS SP-67 or BS EN 593 water short pattern.
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
150#
API 598
Metal Surface
Page 26 of 46
Valve Specification
a. Ball Valves
& Smaller
Min. pressure rating - 500 PSIG @ 100F; F-Bore; Scrd Ends; BB; Replaceable ball &
seats; Cast bronze ASTM B61 body & bonnet; Naval brass ASTM B21 alloy A hard
chrome plated ball; Naval brass ASTM B21 alloy A stem; Buna-N or PTFE stem seals &
seats; LO; Designed to API 608; Inspected to MSS SP-72; Tested to API 598; Fire
300# FF thru bolted FE; BB; F-Bore; Replaceable ball & seats; Cast bronze ASTM B61
body; Carbon Steel ASTM A216 Gr. WCC Cadmium Plated bonnet cap; Cast Bronze
ASTM B61 hard chrome plated ball; Naval Brass ASTM B21 stem; Buna-N or PTFE stem
seals & seats; LO ; G O for 8" & Larger or when recommended by the manufacturer;
Designed to API 608; Tested to API 598; Fire Tested to API 607.
b. Globe Valves
Min. pressure rating - 500 Psig @ 100F; FE; Reduced port; Union bonnet; Inside screw;
Rising stem; Plug type disc; Replaceable disc & seat; Cast bronze ASTM B62 Alloy 836
body, bonnet, union ring, stem & disc holder; Nickel Alloy Plug disc; Buna-N or PTFE
packing; HW operated; Designed to ASME B16.34; Inspected to API 598; Fire Tested to
API 6FA.
c. Check Valve
W5F; Size
& smaller
Min. pressure rating - 500 Psig @ 100F; FE; Horizontal swing; Bolted cover;
Replaceable disc & seat; Cast Bronze ASTM B62 Alloy 836 body & cover; Nickel alloy
W5FW; Size
& larger
300#; Wafer, Replaceable disc & spring; Non Slamming; Aluminium bronze ASTM B148
Alloy 952 body; Al-Bronze ASTM B-150 Alloy 630 Plates; 316SS hinge pin, spring. Stop
pin & pin retainer; Buna-N Seal; Designed to API 594; Tested to API 598.
d. Butterfly Valve
W7FW; Size
4 & larger
300#; Lug type; Replaceable disc & seat; Ni AlBr ASTM B148 Alloy 95800 body, insert,
disc, spacer, compression ring, top compression plate, pressure plug, disc pin, bottom
compression plate & cover plate; Monel shaft; PTFE seat, seals, spacers & gaskets;
Lockable LO; GO for 8 & larger or for smaller size when recommended by Manufacturer;
7.14. Valve
Group X
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Ball Valve
PN 6.3
92 psig at 68
F
API 598
Metal Surface
Refer to MSS-SP-25
X2S; Size 1-
& smaller
1500# Scrd Ends; BB; F-Bore; Floating ball; Non-lubricated; Replaceable ball & seat;
ASTM A182 F316L Body & Bonnet; SS316 Stem & Ball; Teflon or reinforced Teflon
seats; LO.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 27 of 46
Valve Specification
X2R; Size 2 8
150# RF; FE; F-Bore; Replaceable ball & seat; Floating ball; Trunnion Mounted for 6 &
8; Stem packing gland; Ductile iron body section & ball ASTM A395 lined FEP; Stem SS
A 351 CD-4MCu-FEP; PTFE seat ring; Galvanized die cast metal Hand lever; GO for 8.
b. Check Valve
X5S; Size 1-
& smaller
1500#; Scrd Ends; BC; ASTM A182 F316L Body, SS 316 Ball & spring & Teflon or
X5R; Size 2 8
150#; RF; FE; Horizontal swing; BB; Replaceable disc & seat; Cast carbon steel ASTM
A216 W CB body & bonnet with internally ENP; 11.5-13.5% Cr Steel ASTM A182 F6
c. Butterfly Valve
X7R; Size 2 8
150#; RF; Replaceable disc & seat; Ductile iron body ASTM A395 lined PTFE; DIPA-PFA
(encapsulated nickel plated ductile iron insert) Disc & stem; Energized silicone (Viton
7.15. Valve
Group SA
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
:
:
150#
Metal Surface
1. For 1
/
a. Gate Valves
150#; RF; FE; BB; OS & Y Rising stem; Bolted adjustable gland; Plain or flexible solid
wedge; Forged duplex steel ASTM A182 F51 body & bonnet; Forged Stainless Steel
A182 Type 316 wedge & seats ring, HF stellite on contact surface; Stainless steel ASTM
A276 Type 410 stem, Flexible Graphite NAF packing; Body/bonnet bolting ASTM A193
B8MA or B7M & nuts ASTM A194 8MA or 2HM; HW operated; GO for 14" & larger or for
smaller sizes when recommended by the manufacturer; Designed to API 6D; Test and
b. Ball Valves
150#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Forged
duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182 F316
ball & retainer seats; A276 Type 410 stem; Thermoplastic, RPTFE, Elastomer, FKM
resilient seats/seals; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194
8MA or 2HM; Trunnion mounted for 6" & larger; LO for 4 & smaller; GO for 6" & larger or
for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 28 of 46
Valve Specification
SA2R
DIB2S; Size 2
and Larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; Anti
Static; Forged duplex steel ASTM A182 F51 body & bonnet; ASTM A182 F316 ball &
seats retainer; A276 Type 410 stem; Thermoplastic, Reinforced PTFE, FKM resilient
seats/seals; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or
2HM; LO for 4 & smaller; GO for 6" & larger or for smaller sizes when recommended by
the Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
SA2R
DIB2M; Size 2
& Larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;
Forged Duplex Steel ASTM A182 F51 body & bonnet; ASTM A182 F316 + Tungsten
Carbide Coated ball & seats retainer; A276 Type 410 stem; Thermoplastic, Reinforced
PTFE, FKM resilient seals.; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
recommended by manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
d. Plug Valves
150#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;
Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182
F316 plug and seats; ASTM A182 F6A stem; Body/bonnet bolting ASTM A193 B8MA or
B7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO up to 4 ; GO for 6"
& larger or for smaller sizes when recommended by the Manufacturer; Designed to API
6D; Test and Inspection refer to API 6D; Fire Test to API 6FA.
e. Globe Valves
f.
150#; RF; FE; BB; OS & Y; Rising stem; HW operated; Plug or semi-plug disc;
Replaceable disc & seats; Forged duplex steel ASTM A182 F51 body & bonnet; Forged
stainless steel ASTM A182 F316 disc & seat; HF stellite for contact surface; A276 Type
410 stem; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 B8MA or
2HM; Bolted adjustable gland; Guided & tapered seat; Body disc guide for 8 & larger;
Flexible Graphite NAF packing; Designed to API 600; Test and Inspection refer to API
Check Valves
150#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTM
A182 F51 body & cap; Forged stainless steel ASTM A182 F 316 disc, pin & seat; HF
stellite for contact surface; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
A194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 8 & larger or smaller when recommended by the Manufacturer.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 29 of 46
Valve Specification
150#; Wafer; Non-slam; Replaceable plates, springs & integral seats; Forged duplex
steel ASTM A182 F51 body; Plates & seat; Forged stainless steel ASTM A182 F316
hinge pin; Stop pin, & pin retainer; Inconel X750 spring; Design, Test and Inspection refer
to API 6D; Fire T ested to API 6FD; Lifting lug for size 8 & larger or smaller when
recommended by the Manufacturer. (Note: Wafer checks should only be used where
7.16. Valve
Group SB
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
:
:
300#
Metal Surface
1. For 1
/
a. Gate Valves
300#; RF; FE; BB; OS & Y Rising stem; Bolted adjustable gland; Plain or flexible solid
wedge; Forged duplex steel ASTM A182 F51 body & bonnet; Forged Stainless Steel
A182 Type 316 wedge & seats ring, HF stellite on contact surface; Stainless steel ASTM
A276 Type 410 stem, Flexible Graphite NAF packing; Body/bonnet bolting ASTM A193
B8MA or B7M & nuts ASTM A194 8MA or 2HM; HW operated; GO for 14" & larger or for
smaller sizes when recommended by the manufacturer; Designed to API 6D; Test and
b. Ball Valves
300#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Forged
duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182 F316
ball & retainer seats; A276 Type 410 stem; Thermoplastic, RPTFE, Elastomer, FKM
resilient seats/seals; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194
8MA or 2HM; Trunnion mounted for 6" & larger; LO for 4 & smaller; GO for 6" & larger or
for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test
SB2R
DIB2S; Size 2
and Larger
300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; Anti
Static; Forged duplex steel ASTM A182 F51 body & bonnet; ASTM A182 F316 ball &
seats retainer; A276 Type 410 stem; Thermoplastic, Reinforced PTFE, FKM resilient
seats; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;
LO for 4 & smaller; GO for 6" & larger or for smaller sizes when recommended by the
Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 30 of 46
Valve Specification
SB2R
DIB2M; Size 2
& Larger
300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;
Forged Duplex Steel ASTM A182 F51 body & bonnet; ASTM A182 F316 + Tungsten
Carbide Coated ball & seats retainer; A276 Type 410 stem; Thermoplastic, Reinforced
PTFE, FKM resilient seals.; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
recommended by manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
d. Plug Valves
300#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;
Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182
F316 plug, seats, & ASTM A182 F6A stem; Body/bonnet bolting ASTM A193 B8MA or
B7M & Nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO; GO for 8" & larger
or for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test
e. Globe Valves
f.
300#; RF; FE; Reduced port; Extended BB; Bolted adjustable gland; OS & Y; Rising
stem; Plug or semi-Plug disc; Replaceable disc & seats; Forged duplex steel ASTM A182
F51 body & bonnet; Forged stainless steel ASTM A182 F316 disc & seat; HF stellite for
contact surface; A276 Type 410 stem; Body/bonnet bolting ASTM A193 B8MA or B7M &
Nuts ASTM A194 B8MA or 2HM; Guided & tapered seat; Flexible Graphite NAF packing;
Body disc guide for 8 & larger; Designed to API 600; Test and Inspection to API 598;
Check Valves
300#; FF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTM
A182 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, pin & seat; HF
stellite for contact surface; Body/cap bolting ASTM A193 B8MA or B7M & nuts ASTM
A194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 8 & larger or smaller when recommended by the manufacturer.
300#; Wafer; non-slam; replaceable plates, springs & integral seats; Forged Duplex Steel
ASTM A182 F51 body, plates & seal; Forged stainless steel ASTM A182 F316 hinge pin,
stop pin, & pin retainer; Inconel X750 spring; Design, Test and Inspection refer to API 6D;
Fire T ested to API 6FD; Lifting lug for size 8 & larger or smaller when recommended by
the manufacturer. (Note: Wafer checks should only be used where space limitations
dictate).
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 31 of 46
Valve Specification
7.17. Valve
Group SD
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
:
:
600#
Metal Surface
a. Gate Valves
SD1S; Size 1-
800#; Scrd Ends; BB; OS & Y; Rising stem; Solid wedge; Forged duplex steel ASTM
A182 F51 Body & Bonnet; HW operated; Forged stainless steel ASTM A182 F316 wedge
& seats ring; HF stellite contact surface; A276 Type 410 stem; Flexible Graphite NAF
packing; Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Designed to
API 602; Test & Inspection refer to API 598; Fire Test to API 607.
SD1Z; Size 1-
& smaller
800#; SW Ends; BB; OS & Y; Rising stem; Solid wedge; Forged duplex steel ASTM A182
F 51 body & bonnet; HW operated; Forged stainless steel ASTM A182 F 316 wedge &
seats ring; HF stellite contact surface; A276 Type 410 stem; Flexible Graphite packing;
Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Designed to API 602;
Test & Inspection refer to API 598; Fire Test to API 607.
600#; RF; FE; BB; OS & Y Rising stem; Plain or flexible solid wedge; Forged duplex steel
ASTM A182 F51 body & bonnet; Forged Stainless Steel A182 Type 316 wedge & seats
ring, HF stellite on contact surface; Stainless steel ASTM A276 Type 410 stem, Flexible
Graphite NAF packing; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
A194 8MA or 2HM; HW operated; GO for 8" & larger or for smaller sizes when
recommended by the manufacturer; Designed to API 6D; Test and Inspection refer to API
b. Ball Valves
SD2S; Size 1-
800#; 1480 Psig min seat rating of differential pressure; 1480 psi CW P, F-bore; Scrd
ends; BB; Replaceable ball & seats; Forged duplex steel ASTM A182 F51 body &
bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;
Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM B8MA or B7M & nuts ASTM
A194 8MA or 2HM; LO; Designed to API 608; Test & Inspection refer to API 598; Fire
SD2Z; Size 1-
& smaller
800#; SW ends; 1480 psi min. seat rating of differential pressure; 1480 psi CWP; F-Bore;
BB; Replaceable ball & seats; Forged duplex steel ASTM A182 F51 body & bonnet;
Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem; Thermoplastic,
RPTFE seats; Body/bonnet bolting ASTM B8MA or B7M) & nuts ASTM A194 8MA or
2HM); LO; Designed to API 608; Test & Inspection refer to API 598; Fire Test to API 607.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 32 of 46
Valve Specification
800#; SW one end & Scrd other end; 1480 psi min. seat rating differential pressure; 1480
psi CWP; F-Bore; BB; Replaceable ball & seats; Forged duplex steel ASTM A182 F51;
Body & bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;
Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM B8MA or B 7M & nuts ASTM
A194 8MA or 2HM; LO; Designed to API 608; Test & Inspection refer to API 598; Fire
600#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182
F316 ball & retainer seat; A276 Type 410 stem; Thermoplastic, RPTFE, Elastomer, FKM
Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;
Trunnion mounted for 4" & larger; LO for 3 & smaller; GO for 4" & larger or for smaller
sizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspection
SD2R
600#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted; Soft
seated; Anti static; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless
steel ASTM A182 F316 ball & retainer seats; A276 Type 410 stem; Thermoplastic,
Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
A194 8MA or 2HM; LO for 3 & smaller; GO for 4" & larger or for smaller sizes when
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE X SPE; Designed to API 6D; Test & Inspection
SD2R
DIB2M; Size 2
& Larger
600#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;
Metal seated; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless
steel ASTM A182 F6A + Tungsten Carbide Coating ball & seats; A276 Type 410 stem;
Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE X SPE; Designed to API 6D; Test & Inspection
d. Plug Valves
SD3Z; Size 1-
& smaller
800#; SW; Bolted cover; Regular pattern port; Lubricated (unless otherwise noted);
Replaceable plug and seats; Forged duplex steel ASTM A182 F51 body & cover; Forged
stainless steel ASTM A182 F316 plug & seats; A276 Type 410 stem; Body/bonnet bolting
ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design;
LO; Designed to API 599; Test & Inspection API 598; Fire Tested to API 607.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 33 of 46
Valve Specification
SD3S; Size 1-
/
2 & smaller
800#; Scrd Ends; Bolted cover; Regular pattern port; Lubricated (unless otherwise
noted); Replaceable plug & seats; Forged duplex steel ASTM A182-F51 body & cover;
Forged stainless steel ASTM A182 F316 plug & seats; A276 Type 410 stem;
Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194-8MA or 2HM;
Pressure balanced design; LO; Test & Inspection API 598; Designed to API 599; Fire
600#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;
Forged duplex steel ASTM A182-F51 body & bonnet; Forged stainless steel ASTM A182-
F316 Plug & Seats; A276 Type 410 stem; Body/bonnet bolting ASTM A193-B8 MA or
B7M & nuts ASTM A194-8MA or 2HM; Pressure balanced design; LO; GO for 6" & larger
or for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test
e. Globe Valves
800#; Scrd ends; BB; Regular port; OS & Y; Bolted adjustable gland; Rising stem; Plug or
semi plug disc; Replaceable disc & seat; Forged duplex steel ASTM A182-F51 body &
bonnet; Forged stainless steel ASTM A182 F316 disc. & seat, HF stellite for contact
surface; A276 Type 410 stem; HW operated; Flexible Graphite NAF packing;
Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Tapered disc seat; Test
& Inspection refer to API 598; Designed to API 602; Fire Test to API 607.
SD4Z; Size 1-
& smaller
800#; SW ends; BB; Regular port; OS & Y; Bolted adjustable gland; Rising stem; Plug or
semi plug disc; Replaceable disc & seat; Forged duplex steel ASTM A182-F51 body &
bonnet; Forged stainless steel ASTM A182 F316 disc. & seat, HF stellite for contact
surface; A276 Type 410 stem; HW operated; Flexible Graphite NAF packing;
Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Tapered disc seat; Test
& Inspection refer to API 598; Designed to API 602; Fire Test to API 607.
f.
600#; RF; FE; R-bore, BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable
disc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel
ASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type 410 stem ;
Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 B8MA or 2HM;
Guided & tapered seat; Flexible Graphite NAF packing; HW operated; GO for 8" & larger
or for smaller sizes when recommended by the Manufacturer; Body disc guide for 8 &
larger; Designed to API 600; Test & Inspection refer to API 598; Fire Tested to API 6FA.
Check Valve
SD5S; Size 1-
800#; Scrd ends; Horizontal Swing; BC; Replaceable disc & seat; Forged duplex steel
ASTM A182 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, seat & pin;
Body/cap bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM; Design to
SD5Z; Size 1-
& smaller
800#; SW ends; Horizontal Swing; BC; Replaceable disc & seat; Forged duplex steel
ASTM A182 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, seat & pin;
Body/cap bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM; Design to
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 34 of 46
Valve Specification
600#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTM
A182 F51 body & cap; Forged stainless steel ASTM A182-F316 disc, pin & seat, HF
stellite for contact surface; Body/cap bolting ASTM A193-B8MA or B7M & nuts ASTM
A194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 8 & larger or smaller when recommended by the manufacturer.
600#; Wafer non-slam; replaceable plates, springs & integral seats; Forged Duplex Steel
(ASTM A182-F51) body, plates & seat; Forged stainless steel (ASTM A182-F316) hinge
pin, stop pin, & pin retainer; Inconel X750 Spring; Design, Test & Inspection refer to API
6D; Fire T est to API 6FD; Lifting lug for size 8 & larger or smaller when recommended by
the manufacturer. (Note: Wafer checks should only be used where space limitations
dictate).
7.18. Valve
Group SE
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
:
:
900#
Metal Surface
1. For 1
/
a. Gate Valves
900#; RF; FE; BB; OS & Y Rising stem; Plain or flexible solid wedge; Forged duplex steel
ASTM A182 F51 body & bonnet; Forged Stainless Steel A182 Type 316 wedge & seats
ring, HF stellite on contact surface; Stainless steel ASTM A276 Type 410 stem, Flexible
Graphite NAF packing; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
A194 8MA or 2HM; HW operated; GO for 6" & larger or for smaller sizes when
recommended by the manufacturer; Designed to API 6D; Test and Inspection refer to API
900#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182
F316 ball & retainer seat; A276 Type 410 stem; Thermoplastic Devlon or equal resilient
Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;
Trunnion mounted for 4" & larger; LO for 3 & smaller; GO for 4" & larger or for smaller
sizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspection
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 35 of 46
Valve Specification
SE2R
& Larger
DIB2S; Size 2
900#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted; Soft
seated; Anti static; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless
steel ASTM A182 F316 ball & retainer seats; A276 Type 410 stem; Thermoplastic Devlon
or equal resilient seats; FKM seals; Elastomeric material Anti Explosive Decompression
(AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;
LO for 3 & smaller; GO for 4" & larger or for smaller sizes when recommended by the
Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE X SPE; Designed to API 6D; Test & Inspection
SE2R
DIB2M; Size 2
& Larger
900#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;
Metal seated; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless
steel ASTM A182 F6A + Tungsten Carbide Coating ball & seats; A276 Type 410 stem;
Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric material Anti
Explosive Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE X SPE; Designed to API 6D; Test & Inspection
d. Plug Valves
900#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;
Forged duplex steel ASTM A182-F51 body & bonnet; Forged stainless steel ASTM A182-
F316 Plug & Seats; A276 Type 410 stem; Body/bonnet bolting ASTM A193-B8 MA or
B7M & nuts ASTM A194-8MA or 2HM; Pressure balanced design; LO; GO for 4" & larger
or for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test
e. Globe Valves
f.
900#; RF; FE; R-bore, BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable
disc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel
ASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type 410 stem ;
Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 B8MA or 2HM;
Guided & tapered seat; Flexible Graphite NAF packing; HW operated; GO for 8" & larger
or for smaller sizes when recommended by the Manufacturer; Body disc guide for 6 &
larger; Designed to API 600; Test & Inspection refer to API 598; Fire Tested to API 6FA.
Check Valve
900#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTM
A182 F51 body & cap; Forged stainless steel ASTM A182-F316 disc, pin & seat, HF
stellite for contact surface; Body/cap bolting ASTM A193-B8MA or B7M & nuts ASTM
A194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 8 & larger or smaller when recommended by the manufacturer.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 36 of 46
Valve Specification
900#; Wafer non-slam; replaceable plates, springs & integral seats; Forged Duplex Steel
(ASTM A182-F51) body, plates & seat; Forged stainless steel (ASTM A182-F316) hinge
pin, stop pin, & pin retainer; Inconel X750 Spring; Design, Test & Inspection refer to API
6D; Fire Test to API 6FD; Lifting lug for size 8 & larger or smaller when recommended by
the manufacturer. (Note: Wafer checks should only be used where space limitations
dictate).
7.19. Valve
Group SF
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
:
:
1500#
Metal Surface
a. Gate Valves
SF1Z; Size 1-
& smaller
1500#; SW ends; BB; OS & Y; Rising stem, Solid wedge; Forged duplex steel ASTM
A182 F51 body & bonnet, Forged stainless steel ASTM A182 F316 wedge & seat ring,
HF stellite for contact surface; A276 Type 410 stem; Flexible Graphite NAF packing;
Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; HW operated; Designed
to API 602; Test and Inspection refer to API 598; Fire Test to API 607.
1500#; RTJ FE; BB; OS & Y; Rising Stem; Plain or flexible solid wedge; Forged duplex
steel ASTM A182 F51 body & bonnet; Forged stainless steel A182 F316 wedge & seats
ring, HF stellite for contact surface; ASTM A276 Type 410 stem, Flexible Graphite NAF
packing; Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Bolted
adjustable gland; HW operated; GO for 4" & larger or for smaller sizes when
recommended by the Manufacturer; Designed to API 6D, Test & Inspection refer to API
b. Ball Valves
SF2Z; Size 1-
& smaller
1500#; SW ends; 2400 psi min seat rating of differential pressure; 3705 psi CWP; F-Bore;
BB; Non-Lubricated; Replaceable ball & seats; Forged duplex steel ASTM A182 F51
body & bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;
Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts
ASTM A194 8MA or 2HM; Bolted adjustable gland preferred; LO; Designed to API 608;
Test & Inspection refer to API 598; Fire Test to API 607.
SF2ZOS; Size 1-
& smaller
1500#; SW x Scrd. ends; 2400 psi min seat rating of differential pressure; 3705 psi CWP;
F-Bore; BB; Non-Lubricated; Replaceable ball & seats; Forged duplex steel ASTM A182
F51 body & bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;
Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts
ASTM A194 8MA or 2HM; Bolted adjustable gland preferred; LO; Designed to API 608;
Test & Inspection refer to API 598; Fire Test to API 607.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 37 of 46
Valve Specification
1500#; RTJ; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Anti
static; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM
A182 F316 ball & retainer seat; A276 Type 410 stem; Thermoplastic Devlon or equal
resilient seats; FKM seals; Elastomeric material Anti Explosive Decompression (AED);
Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;
Trunnion mounted for 3" & larger; LO for 3 & smaller; GO for 4" & larger or for smaller
sizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspection
SF2J
& Larger
DIB2S; Size 2
1500#; RTJ; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;
Soft seated; Anti static; Forged duplex steel ASTM A182 F51 body & bonnet; Forged
stainless steel ASTM A182 F316 ball & retainer seats; A276 Type 410 stem;
Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric material Anti
Explosive Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts
ASTM A194 8MA or 2HM; LO for 3 & smaller; GO for 4" & larger or for smaller sizes
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE X SPE; Designed to API 6D; Test & Inspection
SF2J
DIB2M; Size 2
& Larger
1500#; RTJ; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;
Metal seated; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless
steel ASTM A182 F6A + Tungsten Carbide Coating ball & seats; A276 Type 410 stem;
Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric material Anti
Explosive Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE X SPE; Designed to API 6D; Test & Inspection
d. Plug Valves
SF3Z; Size 1-
& smaller
1500#; SW Ends; Bolted cover; Regular pattern port; Lubricated (unless otherwise note);
Replaceable plug & seats; Forged duplex steel ASTM A182 F51 body & cover; Forged
stainless steel ASTM A182 F316 plug & seats; Body/bonnet bolting ASTM A193 B8MA or
B7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO; Designed to API
599; Test & Inspection refer t0 API 598; Fire Test to API 607.
1500#; RTJ; FE; BB; Full opening around port; Lubricated (unless otherwise noted);
Replaceable plug & seats; Forged duplex steel ASTM A182 F51 body & bonnet; Forged
stainless steel ASTM A182 F316 plug & seats; Body/bonnet bolting ASTM A193 B8MA or
B7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO; GO for 4" & larger
or for smaller sizes recommended by the Manufacturer; Designed to API 6D; Test &
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 38 of 46
Valve Specification
e. Globe Valves
SF4Z; Size 1-
& smaller
1500#; SW Ends; BB; Regular Port; OS & Y; Rising Stem; Plug or Semi-Plug Disc;
Replaceable disc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forged
stainless steel ASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type
410 stem; Flexible Graphite NAF packing; Body/bonnet bolting ASTM A193 B7M & nuts
ASTM A194 2HM; Tapered disc seat; HW operated; Designed to API 602; Test &
f.
1500#; RTJ; FE; Regular port; BB; OS & Y; Rising stem; Plug or semi-plug disc;
Replaceable disc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forged
stainless steel ASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type
410 stem; Flexible Graphite NAF packing; Body/Bonnet bolting ASTM A193 B8MA or
B7M & nuts ASTM A194 8MA or 2HM; Guided & tapered disc seat; HW operated; GO for
4" & larger or for smaller sizes when recommended by the Manufacturer; Body disc guide
for 8 & larger; Designed to API 602; Test & Inspection refer to API 598; Fire Test to API
607.
Check Valves
SF5Z; Size 1-
& smaller
1500#; SW ends; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel
ASTM A182 F51 body & Cap; Forged stainless steel ASTM A182 F316 disc & seat; HF
stellite for contact surface; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM
A194 8MA or 2HM; Designed to API 602; Test & Inspection refer to API 598.
1500#; RTJ; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel
ASTM A183 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, pin & seat;
HF stellite for contact surface; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts
ASTM A194 8MA or 2HM; Designed to API 6D; Test & Inspection refer to API 6D; Fire
Test to API 6FD; Lifting lug for size 6 & larger or smaller when recommended by the
manufacturer.
1500#; Wafer; non-slam; Replaceable plates & springs, Forged duplex steel ASTM A182
F51 body, plates and seat; Forged stainless steel ASTM A182 F316 hinge pin, stop pin &
pin retainer; Inconel X750 spring; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts
ASTM A194 8MA or 2HM; Designed to API 6D; Test & Inspection refer to API 6D; Fire
Test to API 6FD; Lifting lug for size 6 & larger or smaller when recommended by the
Manufacturer. (Note: Wafer checks should only be used where space limitations dictate).
7.20. Valve
Group A1
Service
Class
Working
Test & Inspection
Painting
Marking
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
:
:
:
:
:
150#
Metal Surface
Page 39 of 46
Valve Specification
a. Gate Valves
150#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceable
wedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced Wedge,
A105 + HF Stellite Seats, A276 Type 410 Stem; SS 309 overlay body cavity; Flexible
Graphite NAF packing; HW operated; GO for 14" & larger or for smaller sizes when
recommended by the manufacturer; Designed to API 6D; Test & Inspection refer to API
b. Ball Valve
A12R;
150#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;
ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI
4140 stem; Seat pocket, seal housing and body cavity, shall be overlaid by SS 309;
Trunnion mounted for 6 & larger; LO for 4 & smaller; GO for 6" & larger or for smaller
sizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspection
A12R
DIB2S; Size 2
& Larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; Anti
Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;
AISI 4140 stem; Seat pocket, seal housing and body cavity, shall be overlaid by SS 309;
Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; LO for 4 & smaller; GO for 6"
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
A12R
DIB2M; Size 2
& Larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated; LO
& smaller; GO for 4 & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A
(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; Seat pocket, seal
housing and body cavity, shall be overlaid by SS 309; Thermoplastic, Reinforced PTFE,
for 3
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
d. Plug Valve
A13R;
150#; RF; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,
inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCB
body & Cover; ASTM A105 + 3 mils ENP plug; SS 309 overlay body cavity; Reinforced
PTFE seats; AISI 4140 stem; LO; GO for 8" & larger or smaller when recommended by the
Manufacturer; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API
6FA.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 40 of 46
Valve Specification
e. Globe Valve
f.
A4R;
150#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;
ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HF
Stellite Seat, A276 Type 410 Stem; SS 309 overlay body cavity; Flexible Graphite NAF
Manufacturer; Body disc guide for 8 & larger; Designed to API 600; Test & Inspect ion
Check Valve
150#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body &
cap; A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite Seat; ASTM A182 F304
hinge pin; ASTM A216 WCB hinge; Designed to API 6D, Test & Inspection refer to API
6D; Fire Test to A PI 6FD; Lifting lug for size 8 & larger or smaller when recommended by
the Manufacturer.
150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Designed to
API 6D; Test & Inspection refer to API 6D; Fire Tested to API 6FD; Lifting lug for size 8 &
larger or smaller when recommended by the Manufacturer. (Note: Wafer check should
A5RW1;
150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,
Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;
Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for
size 8 & larger or smaller when recommended by the Manufacturer. (Note: Wafer checks
A5RW2; Size
2-12
150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &
seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torque
spring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;
Lifting lug for size 8 & larger or smaller when recommended by the M anufacturer. (Note:
150#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body; Monel
plates, seat, stop pin, pin retainer and hinge pin; Inconel X-750 spring; Designed to API
6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for size 8 & larger
or smaller when recommended by the Manufacturer. (Note: Wafer checks should only be
g. Butterfly Valve
150#; Lug type; Replaceable disc & seat; ASTM A216 WCB or ASTM A105 body, bonnet
& disc; 3 mils ENP trim; Shaft ASTM A276 Type 410; Viton seat; Lockable LO; GO for 12"
& larger or for smaller sizes when recommended by the Manufacturer; Designed to API
609; Fire safe designed BS EN 593. Tested & Inspected to API 598.
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 41 of 46
Valve Specification
7.21. Valve
Group XA
Service
Class
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Gate Valve
150#
Metal Surface
150#; RF; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCB
body & bonnet; A105 + 11.5-13.5% Cr faced Wedge, A105 + HF Stellite Seat, A276 Type
410 Stem; Flexible Graphite NAF packing; HW operated; GO for 10" & larger or for
smaller sizes when recommended by the manufacturer; Designed to API 6D; Test &
b. Ball Valve
150#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Anti
static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;
AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ball
for up to 4; Trunnion mounted for 6 & larger; LO for 4 & smaller; GO for 6" & larger or for
smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &
XA2R
DIB2S; Size 2
& Larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Soft
seated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &
seats retainer; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient
seats/seals;
LO for 4 & smaller; GO for 6" & larger or for smaller sizes when
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
XA2R
DIB2M; Size 2
& Larger
150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metal
seated; LO for 3 & smaller; GO for 4 & larger; ASTM A216 WCB body & bonnet; ASTM
A182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem;
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 42 of 46
Valve Specification
7.22. Valve
Group XB
Service
Class
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Gate Valve
XB1R; Size 2
300#
Metal Surface
& larger
300#; RF; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCB
body & bonnet; A105 + 11.5-13.5% Cr faced Wedge, A105 + HF Stellite Seat, A276 Type
410 Stem; Flexible Graphite NAF Packing; HW operated; GO for 6" & Larger or for
Smaller Sizes when recommended by the manufacturer; Designed to API 6D; Test &
b. Ball Valve
XB2R; Size 2
300#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Anti
static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;
AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ball
for up to 4; Trunnion mounted for 6 & larger; LO for 4 & smaller; GO for 6" & larger or for
smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &
XB2R
DIB2S; Size 2
& Larger
300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Soft
seated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &
seats retainer; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seal;
LO for 4 & smaller; GO for 6" & larger or for smaller sizes when recommended by the
Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
XB2R
DIB2M; Size 2
& Larger
300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metal
seated; LO for 3 & smaller; GO for 4 & larger; ASTM A216 WCB body & bonnet; ASTM
A182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem;
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
7.23. Valve
Group XD
Service
Class
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
600#
Metal Surface
Page 43 of 46
Valve Specification
a. Gate Valve
XD1R; Size 2
& larger
600#; RF; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCB
body & bonnet; A105 + 13.5% Cr faced wedge, A105 + HF Stellite seat ring, A276 Type
410 stem; Flexible Graphite NAF packing; HW operated; GO for 4" & larger or for smaller
sizes when recommended by the manufacturer; Designed to API 6D; Test & Inspection
b. Ball Valve
600#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Anti
static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;
AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Elastomeric
mounted for 4 & larger; LO for 4 & smaller; GO for 4" & larger or for smaller sizes when
recommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API
XD2R
DIB2S; Size 2
& Larger
600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Soft
seated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &
seats retainer; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient
smaller; GO for 4" & larger or for smaller sizes when recommended by the Manufacturer.
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
XD2R
DIB2M; Size 2
& Larger
600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metal
seated; LO for 3 & smaller; GO for 4 & larger; Anti Static; ASTM A216 W CB body &
bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140
stem; Thermoplastic, Reinforced PTFE, FKM resilient seals. Elastomeric material Anti
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
7.24. Valve
Group XE
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
Note
900#
Metal Surface
For 1
/
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 44 of 46
Valve Specification
a. Gate Valve
900#; RF ; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCB
body & bonnet; A105 + 13.5% Cr faced wedge, A105 + HF Stellite seat ring, A276 Type
410 stem; Flexible Graphite NAF packing; HW operated; GO for 4" & larger or for smaller
sizes when recommended by the manufacturer; Designed to API 6D; Test & Inspection
b. Ball Valve
900#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Anti
static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;
AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric
mounted for 4 & larger; LO for 4 & smaller; GO for 4" & larger or for smaller sizes when
recommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API
XE2R
DIB2S; Size 2
& Larger
900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Soft
seated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &
seats retainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;
Elastomeric material Anti Explosive Decompression (AED). LO for 3 & smaller; GO for 4"
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
XE2R
DIB2M; Size 2
& Larger
900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metal
seated; LO for 3 & smaller; GO for 4 & larger; ASTM A216 WCB body & bonnet; ASTM
A182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem;
Thermoplastic Devlon or equal resilient seats; FKM seals. Elastomeric material Anti
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
7.25.
Valve Group XF
Service
Rating
Working
Test & Inspection
Painting
:
:
:
:
:
Marking
a. Gate Valve
1500#
Metal Surface
1500#; RTJ; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCB
body & bonnet; A105 + 13.5% Cr faced wedge, A105 + HF Stellite seat ring, A276 Type
410 stem; Flexible Graphite NAF packing; HW operated; GO for 3"& larger or for smaller
sizes when recommended by the manufacturer; Designed to API 6D; Tested & Inspected
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 45 of 46
Valve Specification
b. Ball Valve
1500#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated;
Anti static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 m ils E N P ball & seat
retainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;
Trunnion mounted for 3 & larger; LO for 2 ; GO for 3" & larger or for smaller sizes when
recommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API
XF2J
& Larger
DIB2S; Size 2
1500#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Soft
seated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &
seats retainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;
Elastomeric material Anti Explosive Decompression (AED). LO for 2; GO for 3" & larger or
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
XF2J
DIB2M; Size 2
& Larger
1500#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metal
seated; LO for 2; GO for 3 & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A
(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; Thermoplastic
Devlon or equal resilient seats; FKM seals. Elastomeric material Anti Explosive
Decompression (AED).
Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainer
have 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection refer
PHEONWJ-M-SPE-0023 Rev. 1
Paper Copies are Uncontrolled
Page 46 of 46