Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
RX TX RX TX
31 32 33 34 35 36 37 38 39 40 41
CL
-0.2
Page 1/4
December 2008
GND +A
B GND +A
RS485_1
RS485_2
Input
Input
Voltage
Current
Analog
Inputs
Digital
Inputs
Signal Limits
Consumption
DIGITAL
INPUT
GND +A
45 46 47 48 49 50 51 52 53 54 55 56 57
RS485_3
AI4 GND
DO1
ANALOG
INPUT
DO2
DO3
DO4
DIGITAL
OUTPUT
DI1 DI2
STATUS
TX RX
42 43 44
Nominal
Frequency
Overload
Auxiliary Power
Supply
Output
Phase
Line
80V
140V
150V
260V
300V
520V
1A , 5A
04 Inputs 0...20mA ou 4...20mA
Input Impedance: 150
12 bits ADC
Response Time: < 100ms
Error Limit: 0,2%
04 TTL Input 5V 1mA
Response Time: <1ms
U = 10120%
I = 5...150%
Voltage Input: 2mA.
Current Input: 0,2VA.
50 or 60 Hz 10%
Permanently: 1,5 x U ; 2 x I
Short time: 4 x U/1s;50 x I/1s
maximum: 250A /1s
85 265Vac/90300Vdc
Power consumption ~ 5VA
Digital Output
Serial Interface
ETE-300
Page 2/4
December 2008
Influence Magnitudes
Error Limit
EL=0,2%
(Optional)
Reference
Conditions
Climatic condition
Voltage
Current
Active Power
Reactive Power
Apparent Power
Power Factor
Frequency
Active Energy (Direct
and reverse flux)
Reactive Energy
(Value EL)
(Value EL)
(Value EL)
(Value EL)
(Value EL)
0,01
0,05 Hz
(W Error EL of
reading)
(VAR Error + EL of
reading)
Input:
I = 5%...100% ;
U = 10%...100%
fnom 2%
Specified Values
cos = 1 (Active Power)
sin = 1 (reactive
power)
25C 2K
Frequency:
Aux. Power Supply:
Power Factor:
Temperature:
Thermal Stability:
20 minutes.
Additional Errors
Additional error above 1,2I
or 1,2U
Linearity deviation
Temperature
Auxiliary power supply
External magnetic fields
0,2%
0,2% (included in error limit)
0,2%/10 K; rated temperature
25C
0,05% within the tolerance
range admissible for the power
supply voltage
0,5% for field intensity of
0,4 kA/m
Electric Tests
Test voltage
Aluminum
DIN Rail Mounting .
Voltage, Current and Auxiliary power Supply
using ring shaped cable shoes.
Digital Input, Digital Output, RS485 and Analog
Input terminals for pin shaped cable shoes.
IP 30 (Housing)
IP 20 (Terminal Connections)
~ 1,0 kg
Operating temperature
Functioning temperature
Transport and storage
temperature
Relative humidity
-20...+60C
-25...+70C
-40...+80C
75% of annual mean with small
condensation
(others upon request)
Mechanical Tests
Impact
Vibration
ETE-300
Page 3/4
December 2008
105,0
Dimensional Drawing
Dimensions in mm
11
13
14
12
182,0
95,2
Additional Information
The following items contain tips and cautions to be observed by the
user for a good functional performance, as well as the maintenance
of the instrument and the safety of the installations
Cautions
Be sure that the voltage and current to be connected to the
instrument are compatible.
Loosen all connections from the instrument before removing it from
the installation.
Mounting Instructions
Observe the ambient temperature range. At the place of installation,
values for vibration, dust, dirt and humidity, which must remain
between the limits, established by the protection class of the housing
and the climatic group, specified in this data sheet, have to be
observed.
For mounting on DIN rail, use the snap-in device on the rear of the
instrument.
The connections can be made with pin for shaped cable shoes, for
the input signals in Voltage and Current and for the Auxiliary
Power; RS485 and digital outputs terminals type pin
.
.
ETE-300