Sei sulla pagina 1di 10

VIVA 4G LTE Mini Router

Quick Start Guide

Thank you for choosing the VIVA 4G LTE Mini


Router (hereinafter referred to as the E57)
The supported functions and actual appearance are subject to the product purchased.
The following pictures are displayed for illustration purposes only. For the product
selection details, consult your service provider.
This guide briefly describes the functions of the E57. For details about how to set the
management parameters, see the Help section on the Web Management page.
If the E57 is placed in an environment with poor ventilation, it will become warm after
extended use. When the E57 temperature reaches a certain high tempreature, it will
switch off or disconnect from the network automatically to protect itself. If this happens,
please place the E57 in a well-ventilated area for heat dissipation and then restart it.

Application Scenarios
The Wi-Fi device or computer can connect to the internet through the E57. The
actual connection procedure depends on the operating system of the Wi-Fi device or
computer. You can perform the connection operations as prompted.

1 Scenario connecting multiple devices through Wi-Fi

2 Scenario connecting a single device through USB

3 Scenario multi-device access via Wi-Fi and USB at


the same time

Screen

1 Signal strength
: Signal strength from weak to strong.

2 Network type
2G/3G/4G: Connected to a 2G/3G/LTE network.
R: Data roaming is On.

3 Wi-Fi
Wi-Fi is On.
Number of connected Wi-Fi devices.

4 SIM card slot


: Battery level from low to high.

5 SMS
New messages.
Number of new messages.
Network connection status.

6 Internet connection is set up


Traffic statistics.
Data traffic information.
Connection time.

Note:
Wi-Fi: wireless connection quality.
WPS: protected setup.
Data traffic information is for your reference only. For more accurate data traffic
information, please consult your service provider.

Before You Start Installing the SIM Card


and the Battery
Insert the SIM card in the card slot. Ensure the SIM card is facing in the right direction,
as shown in the figure below, and then slide the SIM card into the slot.

Note:
When removing the SIM card, open the tab and gently press the SIM card in, then
release. The card will automatically pop out.
Do not remove the SIM card when it is in use. Otherwise, the card and the Wi-Fi may
be damaged, and data stored on the card may be lost.
Do not remove the SIM card when it is in use. Doing so will affect the performance
of your Mobile WiFi and data stored on the SIM card may be lost.

Installing the microSD Card


Insert the MicroSD as shown below.

Note:
The MicroSD card is an optional accessory. If a MicroSD card is not provided in
the package, you may buy one.
To remove the MicroSD card, press the card in gently. The MicroSD card will pop
out for removal.
Do not remove the MicroSD card when it is in use. Otherwise, the card and
the E57 may be damaged, and data stored on the card may be lost.

Charging the Battery


Note:
If the battery has not been used for a long time, it must be recharged first.

Method 1: Using the charger

Caution:
Only use the charger compatible with the E57 and provided by the designated
manufacturer. If a charger incompatible with the device model or provided by other
manufacturers or vendors is used, the E57 may fail to work and damage to the device
may occur. At the same time, any national regulations on communications products or
warranty applicable to the E57 will be canceled. The charger is an optional accessory, if
the charger is not provided in the package you can contact your local dealer to buy one.

Method 2: Connecting to a PC for charging


Connect the Mobile Wi-Fi to a PC using a compatible data cable.

Accessing the Internet via Wi-Fi Connection


Note:
By default, management parameters are preset on the E57 according to the
requirements of VIVA, the service provider. You may follow the steps below to quickly
access the Internet. For details about how to set management parameters, see the Help
section on the Web Management page.

Step1: Power on the E57


Press and hold

until the screen lights up. The E57 is powered on.

Note:
Press and hold

to power off the E57.

Step 2: Establish a Wi-Fi Connection (Below example


uses Windows XP OS)
1. Make sure that the Wi-Fi is enabled.
2. Select Start > Control Panel > Network Connections > Wireless Network Connection.

Note:
To set up a Wi-Fi connection, the PC must have a wireless network adapter installed.
If Wireless Network Connection is displayed, a wireless network adapter is available.
Otherwise, check to make sure you have a wireless network adapter installed.
3. Click View available (wireless networks) to display a list of wireless networks available.
4. Select a network indicated by the SSID of the E57, and then click Connect.

Note:
If the encryption parameter is already set for the E57, the Wireless Network
Connection dialog box is displayed. Enter the network password in the dialog box.
The SSID and network key label are affixed to your E57. Press the WPS button twice
to view the current SSID and wireless network encryption key on the screen.
Wait until the wireless connection icon is displayed in the status area in the lower right
corner of the PC screen.

Step 3: Access the Internet


After you establish a Wi-Fi connection successfully, you can access the Internet using
the following modes. By default, the mode is Auto.
Mode
Auto
Manual

Operations
After the E57 is powered on, it can automatically connect to the
internet when data transmission is required. If data transmission is not
performed over a period of time, the E57 automatically disconnects
from the Internet connection.
Launch the Web Management page and follow the prompts to connect
to or disconnect from the network.

Note:
Launch the Web Management page to select the mode for accessing the Internet.
If the E57 accesses the roaming network, the E57 automatically disconnects from
the established network connection. If you need to access the Internet from the new
network, you must re-establish a network connection.

Accessing the Web Management Page


1. Make sure that the connection between the E57 and the device is properly established.
2. Start the Internet browser and enter http://192.168.1.1 in the address bar.
3. Enter the password and log in to the web management page.

Note:
The default password is admin.

Create a Secure Connection


1. Launch the web browser and enter http://192.168.1.1 in the address bar.
2. Enter the password and click login. The default password is admin.
3. Click on Settings.
4. Click on Quick setup. A message Welcome to the quick setup wizard will be shown.
5. Click on Next. A message Configure Profile Settings will be shown.
6. Click on Next. A message Configure Dial-up Settings will be shown.
7. Click on Next. A message Configure WLAN settings will be shown. Insert the
desired router name in the Name (SSID) field
8. Click on Next. For the Authentication select Auto, for the Encryption mode
select WEP. Enter the desired network key in the Network key 1 field. This key will
be requested every time a user tries to access this connection.
9. Click on Next
10. Click on Finish. A message The action will disconnect your connection, are you
sure to proceed? will be shown
11. Click on Ok.

Note:
The password that you will set for your device should be in numerical format
(example 123456).

Daily Use
Power Saving Mode
If no operation is performed on the E57 for a while, the screen turns off. Press any key to
light up the screen.
If the E57 is powered by the battery only, choose whether to enable the E57 to turn off
Wi-Fi automatically. If this function is enabled and no Wi-Fi devices access the E57 for a
set period, the E57 turns off Wi-Fi automatically. You can press any key to turn on Wi-Fi
again.

Establishing a WPS
Connection
If a Wi-Fi client connected to the E57
supports the WPS function, a network
key will be automatically generated
without manual input. To establish a WPS
connection, perform the following steps:
1. Power on the E57.
2. Start the client.
3. Enable the WPS function of the E57.
4. Enable the WPS function of the client.

Note:
After Wi-Fi is enabled, press and hold the WPS button to enable the WPS function of
the E57.
For WPS operations on the client, see the user guide of the client.

Restoring Factory Defaults


If you forget the changes you have made to some
parameters, you may restore factory defaults and
reconfigure the E57.
To restore the factory defaults: press and hold the
RESET button until the screen turns off. All factory
default settings will be successfully restored.

Note:
Restoring factory defaults deletes all personal configuration settings and restores all
web-based management settings and parameters to their default values.

Tips
If you are experiencing difficulties using the E57, try the following:
See the (Help) section on the Web Management page.
Restart the E57.
Restore the factory defaults.
Contact your service provider.

Potrebbero piacerti anche