Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. Types of soils:
Soil Type
Gravels
Sands
Silts
Clays
Particle Size
Characteristics
10 cm 2 mm
2 mm 0.060 mm
0.060 mm 0.002 mm They have better water retention than larger sized
particles.
These data can be used to show the soil particle size distribution as a curve by plotting
percentage of particles passing through against sieve diameter.
2 coefficients:
a) Coefficient of uniformity, Cu is the ratio between the diameter of the sieve where 60% of
the material passes through, and of the sieve where 10% passes through.
If Cu < 5 = the soil has uniform grain size
If 5 < Cu < 20 = the soil has slightly uniform grain size
If Cu > 20 = the soil is well graded
The more uniform the soil particle size distribution curve, the more uniform the void size
will be. This makes the soil less dense and more liable to erosion.
b) The fine particle content is the percentage of soil that passes through ASTM sieve 200
(0.075mm). This percentage indicates the proportion of clay and silt contained in the soil,
and is related to potential water retention. The greater the content of fine particles, the
more difficult it will be to expel water.
c) Coarse-grained soils have more than 50 % of the particles larger than 0.075 mm, and
fine-grained soils have more than 50 % equal to or smaller 0.075 mm.
3. Plasticity
Measuring the soil particle size distribution is the first step in soil classification, but in some soils
this is not so clear especially for the case of soil in mixtures of silts, clays and sand.
The water content is the weight of water in the soil divided by weight of dry soil. It normally
varies from 5 8 % in granular soils, and from 60 70% in clayey soils. The weight of water is
calculated from the difference between weight of soil sample before and after it is oven-dried for
the time required for the water to evaporate.
Atterberg defined 3 limits:
a) Shrinkage limit transition between solid and semi-solid state
b) Plastic limit separating semi-solid from plastic state
c) Liquid limit separating plastic from semi-liquid state
Plastic and Liquid Limit are the most commonly used in practice and they are determined from
the soil fraction that passes through sieve 40 (0.01 mm).
Plastic limit is determined by kneading dry soil with a little water to form small balls and then
rolling them out with the palm of the hand on a smooth surface to a diameter of about 3 mm and
length of about 25 30 mm. If at this stage the rolls crack into pieces of about 6 mm long, their
water content corresponds to that of the plastic limit. If they do not crack, the rolls are reshaped
into a ball and rolled in the hand, until they lose water content and re-rolled, this being repeated
until they start cracking.
There are several methods in determination of liquid limit and the percussion method, originally
proposed by Casagrande is a simple yet effective method, this method is normally included in the
learning syllabus.
The liquid limit can be obtained using percussion method by kneading dry soil with sufficient
water to make a suspension with the consistency of yoghurt, and putting this into the Casagrande
cup mould. Using a grooving tool, a groove of 2 mm wide at its lowest point is then cut across
the center of the mass. The mould is placed on a base and subjected to regular blows, which are
counted. The liquid limit is the water content of the sample when the groove closes along a
distance of some 12 mm after 25 blows. As it is difficult to achieve this, the water content is
determined by interpolation from several samples, in which 12 mm closure has to be achieved
with more or less 25 blows. At least 3 tests for the same soil should be made at varying moisture
content.
Once Liquid Limit (LL) and Plastic Limit (PL) has been found, a point representing each soil
sample can be obtained from the Casagrande Plasticity Chart which shows the ratio between the
liquid limit and the plasticity index (PI).
PI represents the moisture content interval for passing from a semi-solid to a semi-liquid state.
From a series of practical studies, Casagrande defined soils with LL > 50 as having high
plasticity i.e. they absorb a large amount of water and may experience considerable plastic
deformation. Below this value, soils are considered to have low plasticity. Casagrande completed
this system of identification with particle size distribution data and developed the widely used
Unified Soil Classification System.
The liquidity index, LI is defined by the ratio of the natural water content of the soil sample
minus water content at the plastic limit to the index of plasticity. It normally varies between 0
and 1.
LI = (w PL) / (LL PL)
In sands, where water retention and plasticity are very low or absent, a comparison of this type is
not usually made.
Liquidity Index, LI
Very Soft
1.00 0.80
> 55
Soft
0.80 0.65
40 55
Firm
0.65 0.40
25 40
Stiff
0.40 0.25
15 25
Hard
< 0.25
< 15