Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Domain
Software
Microcontroller
AT89S8252
Power Supply
Display
RTC
DS 1307
Crystal
Input
3X4 keypad
Technical support
Phone
Hyderabad: Tarakarama Estates, 2nd Left Lane Opp RS Brothers, Ameerpet, Hyderabad 500073
Vijayawada: 4th Floor, White House, Opp All India Radio, MG Road, Vijayawada 520010
www.WineYardProjects.comPh:04064646363,66256695,8885555212
WK217
Advertising hoardings, commercial sign boards, and street lights are generally
switched on at 6:30 pm and switched off at 10:00 am because nobody is available at
the place in the morning to switch it off. But actual required time is 6:30pm to
11:30pm and 4:30am to 6:30am. Meantime i.e., from 11:30pm to 4:30am is not
required, because the public flow on the roads is almost nil in this time. And from
6:30am to 10:00am is also not required as the sun light is available during this time.
That means every day around nine hours of power is wasted. This project gives the
best solution for electrical energy wastage. Also the manual operation of the lighting
system is completely eliminated.
The Project AT89S8252 Microcontroller Based Energy saver for Commercial
Lighting system with RTC DS1307 Interfacing is an interesting project which uses
AT89S8252 microcontroller as its brain. This project is very useful for commercial
sign boards, advertising boards, street lights for automation lighting system. This
system switches on the lights only at preprogrammed timings. As the DS1307 Real
Time Clock chip with battery back-up is used, there will be no disturbances for the
programmed on/off timings even in power failures.
3X4 keypad is provided for entering the required timings. This keypad made
this project user friendly. 4-digit seven segment display is provided to display the
alarm times and current time. DS1307 is interfaced to the microcontroller for real
timing performance. A 3V battery can be connected to DS1307 to avoid time
disturbances caused by power failures.
AT89S8252 has inbuilt flash EPROM. Data stored remains in the memory
even after power failure, as the memory ensures reading of the latest saved settings by
the micro controller. It can retain data for more than ten years.
This project uses regulated 5V, 500mA power supply. Unregulated 12V DC is
used for relay. 7805 three terminal voltage regulator is used for voltage regulation.
Bridge type full wave rectifier is used to rectify the ac out put of secondary of
230/12V step down transformer.
Hyderabad: Tarakarama Estates, 2nd Left Lane Opp RS Brothers, Ameerpet, Hyderabad 500073
Vijayawada: 4th Floor, White House, Opp All India Radio, MG Road, Vijayawada 520010
www.WineYardProjects.comPh:04064646363,66256695,8885555212
ABSTRACT
WK217
WK217
Back-up
Battery
16X2 LCD
DS1307
RTC
Contrast
AT89S8252
With in built
Flash EPROM
Crystal
Control
Switch
set
Crystal
Transistor
Driver circuit
Reset
circuit
Step
down
T/F
Bridge
Rectifier
Filter
Circuit
Relay
+12V to Relay
Hyderabad: Tarakarama Estates, 2nd Left Lane Opp RS Brothers, Ameerpet, Hyderabad 500073
Vijayawada: 4th Floor, White House, Opp All India Radio, MG Road, Vijayawada 520010
www.WineYardProjects.comPh:04064646363,66256695,8885555212
Block Diagram