Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Draft A
Date
2014-01-20
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Contents
Contents
1 About This Document..................................................................................................................1
1.1 Scope..............................................................................................................................................................................1
1.2 Intended Audience..........................................................................................................................................................1
1.3 Change History...............................................................................................................................................................1
2 Overview.........................................................................................................................................3
3 Technical Description...................................................................................................................5
4 Related Features...........................................................................................................................11
5 Network Impact...........................................................................................................................12
6 Engineering Guidelines.............................................................................................................13
6.1 When to Use.................................................................................................................................................................13
6.2 Required Information...................................................................................................................................................13
6.3 Deployment..................................................................................................................................................................14
6.3.1 Requirements.............................................................................................................................................................14
6.3.2 Data Preparation........................................................................................................................................................15
6.3.3 Activation..................................................................................................................................................................16
6.3.4 Activation Observation..............................................................................................................................................18
6.3.5 Deactivation...............................................................................................................................................................19
6.4 Performance Monitoring...............................................................................................................................................21
7 Parameters.....................................................................................................................................23
8 Counters......................................................................................................................................108
9 Glossary.......................................................................................................................................109
10 Reference Documents.............................................................................................................110
ii
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
1.1 Scope
This document describes WRFD-140222 Adaptive Adjustment of HSUPA Small Target
Retransmissions, including its technical principles, related features, network impact, and
engineering guidelines.
You are advised to read HSUPA Feature Parameter Description before reading this document.
Feature change
Changes in features of a specific product version
Editorial change
Changes in wording or addition of information that was not described in the earlier version
Draft A (2014-01-20)
Compared with Issue 01 (2013-04-28) of RAN15.0, Draft A (2014-01-20) of RAN16.0 includes
the following changes.
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Change Type
Change Description
Parameter Change
Feature change
None
Editorial change
None
None
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
2 Overview
Overview
The hybrid automatic repeat request (HARQ) entity for High Speed Uplink Packet Access
(HSUPA) is located on the NodeB side and used to receive MAC-e protocol data units (PDUs).
When a cell cannot correctly receive MAC-e PDUs from a UE, the HARQ entity requires the
UE to retransmit MAC-e PDUs. The average number of retransmissions on the NodeB side
needs to converge to a target number of retransmissions on the RNC side. This target number
on the RNC side is dynamically adjusted by the feature HSUPA Adaptive Retransmission.
With the HSUPA adaptive retransmission feature, a small target number of retransmissions is
used under normal circumstances. When the uplink load or the UE transmit power is limited,
one UE is selected to use a large target number of retransmissions during each period. Without
this feature, a small target number of retransmissions is always used. For details about the
HSUPA adaptive retransmission feature, see HSUPA Feature Parameter Description.
In versions earlier than RAN14.0, the small target number of retransmissions is specified by the
EdchTargetLittleRetransNumparameter and cannot be adaptively adjusted. When the uplink
load is limited, a small target number of retransmissions will require a high signal-to-interference
ratio (SIR) on the Dedicated Physical Control Channel (DPCCH), and the DPCCH must have a
higher power. This leads to decreased available power on the Enhanced Dedicated Channel (EDCH) and Enhanced Dedicated Physical Data Channel (E-DPDCH), a lower UE throughput,
and a lower cell throughput. The feature Adaptive Adjustment of HSUPA Small Target
Retransmissions supports an alternative small target number of retransmissions for each typical
type of service. The actual small target number of retransmissions can dynamically shift between
the original fixed number and the alternative number based on the cell uplink load and UE rates,
which are configured by the EdchTargetLittleRetransNum and
EdchAltTarLittleRetransNum parameters, respectively. This improves the system capacity
when the uplink load is limited.
This Adaptive Adjustment of HSUPA Small Target Retransmissions feature is only intended
for the HSUPA services of the non-DC-HSUPA UEs.
Figure 2-1 shows the relationship between the features HSUPA Adaptive Retransmission and
Adaptive Adjustment of HSUPA Small Target Retransmissions.
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
2 Overview
Figure 2-1 Relationship between the features HSUPA Adaptive Retransmission and Adaptive
Adjustment of HSUPA Small Target Retransmissions
The features HSUPA Adaptive Retransmission and Adaptive Adjustment of HSUPA Small
Target Retransmissions are independent of each other. With the HSUPA Adaptive
Retransmission feature, only one UE is selected to use the large target number of retransmissions
during each period. With the Adaptive Adjustment of HSUPA Small Target Retransmissions
feature, when the uplink load is limited, multiple UEs are selected for adjustment to the small
target number of retransmissions. This further improves the cell throughput.
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
3 Technical Description
Technical Description
Without the feature Adaptive Adjustment of HSUPA Small Target Retransmissions, the RNC
sets different target numbers for different typical types of services through the
EdchTargetLittleRetransNum parameter. This feature is intended to further improve the cell
throughput. An alternative small target number of retransmissions is available for each typical
type of service. This alternative small number is configured by the
EdchAltTarLittleRetransNum parameter. The original small number is configured by the
EdchTargetLittleRetransNum parameter. The small target number of retransmissions
dynamically shifts between EdchTargetLittleRetransNum and
EdchAltTarLittleRetransNum.
The Adaptive Adjustment of HSUPA Small Target Retransmissions feature dynamically adjusts
the small target number of retransmissions for each individual BE service over HSUPA. There
are two adjustment algorithms: RTWP-based Adjustment of HSUPA Small Target
Retransmissions and RSCP- and RTWP-based Adjustment of HSUPA Small Target
Retransmissions. The BASE_RSCP_RTWP_LITRETNUM_AUTOADJ_SWITCH under
the RscpEffectAlgoSwitch parameter controls which adjustment algorithm is used.
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
3 Technical Description
Figure 3-1 Procedure for dynamically adjusting the small target number of retransmissions
based on the RTWP
When the UE attempts to access the network, the larger value between
EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum is used as the small target
number of retransmissions if PC_HSUPA_LITRETNUM_INIT_SEL_SWITCH under the
PcSwitch parameter is selected, or EdchTargetLittleRetransNum is used if
PC_HSUPA_LITRETNUM_INIT_SEL_SWITCH under the PcSwitch parameter is not
selected.
After the UE accesses the network, the following rules apply if
PC_HSUPA_LITRETNUM_AUTO_ADJUST_SWITCH under the PcSwitch parameter is
selected:
l
If the UE rate is above the upper threshold and the uplink load of the cell has not reached
MaxTargetUlLoadFactor multiplied by RelRatioforUlRTWP, the RNC adjusts the small
target number of retransmissions to the smaller one between
EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum in order to raise the UE
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
3 Technical Description
throughput. The upper threshold equals the minimum bit rate (MBR) of uplink services
multiplied by an unconfigurable factor.
l
If the UE rate is below the lower threshold, the RNC adjusts the small target number of
retransmissions to the larger one between EdchTargetLittleRetransNum and
EdchAltTarLittleRetransNum in order to raise the cell throughput on the uplink. The lower
threshold equals the MBR of uplink services multiplied by an unconfigurable factor.
Unconfigurable
Factor for the Upper
Threshold
Unconfigurable
Factor for the
Lower
Threshold
<1
90%
60%
90%
70%
75%
70%
75%
70%
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
3 Technical Description
Figure 3-2 Procedure for dynamically adjusting the small target number of retransmissions
based on the RSCP and RTWP
The UE's uplink coverage is determined based on the P-CPICH RSCP, which can be obtained
from the periodically reported intra-frequency measurement reports. The
RrcRscpPeriodTimer parameter in the SET UCHLQUALITYEVALUATE command
specifies the measurement period of the P-CPICH RSCP. A UE's uplink coverage is not limited
if the following conditions are met:
l
If the duration between the current time and the time the RNC receives a measurement
report containing information about P-CPICH RSCP does not exceed the value of
EcN0EffectTime, the calibrated P-CPICH RSCP calculated based on the reported PCPICH RSCP meets the following conditions:
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
3 Technical Description
For UEs using the 2 ms TTI, the calibrated P-CPICH RSCP is greater than the value of
BeTTI2msRscpUpThd.
For UEs using the 10 ms TTI, the calibrated P-CPICH RSCP is greater than the value
of BeTTI10msRscpUpThd.
Calibrated P-CPICH RSCP = Reported P-CPICH RSCP (Transmit power on the P-CPICH
33 dBm) (RTWP (-105.2 dBm))
l
If the duration between the current time and the time the RNC receives a measurement
report containing information about P-CPICH RSCP exceeds the value of
EcN0EffectTime, the P-CPICH Ec/N0 in the RRC CONNECTION REQUEST message,
CELL UPDATE message, or traffic volume-based event 4A/4B measurement report must
meet the following conditions:
For UEs using the 2 ms TTI, the P-CPICH Ec/N0 must be greater than the value of
EcN0ThsFor2msTo10ms.
For UEs using the 10 ms TTI, the P-CPICH Ec/N0 must be greater than the value of
EcN0ThdForBaseCoverE2D.
The duration between the current time and the time the RNC receives an RRC CONNECTION
REQUEST or CELL UPDATE message is recorded as duration 1. The duration between the
current time and the time the RNC receives a traffic volume-based event 4A/4B measurement
report is recorded as duration 2. If both duration 1 and duration 2 are greater than the value of
EcN0EffectTime, the P-CPICH Ec/N0 is replaced by FakeEcNo.
NOTE
The RNC uses the P-CPICH Ec/N0 in a traffic volume-based event 4A/4B measurement report only when
the DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH check box under the DraSwitch2
parameter in the SET UCORRMALGOSWITCH command is selected.
If the UE rate is above the upper threshold and the uplink load of the cell has not reached
MaxTargetUlLoadFactor multiplied by RelRatioforUlRTWP, the RNC adjusts the small
target number of retransmissions to the smaller one between
EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum in order to raise the UE
throughput in the uplink. The upper threshold equals the MBR of uplink services multiplied
by an unconfigurable factor (see Table 3-1 for details).
If the UE coverage is not limited and the uplink load of the cell has not reached
MaxTargetUlLoadFactor multiplied by RelRatioforUlRTWP, the RNC adjusts the small
target number of retransmissions to the smaller one between
EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum in order to raise the UE
throughput in the uplink.
If the UE rate is below the lower threshold, the RNC adjusts the small target number of
retransmissions to the larger one between EdchTargetLittleRetransNum and
EdchAltTarLittleRetransNum in order to raise the cell throughput in the uplink when either
of the following conditions is met: The uplink load of the cell has reached
MaxTargetUlLoadFactor multiplied by RelRatioforUlRTWP; the UE coverage is limited.
The lower threshold equals the MBR of uplink services multiplied by an unconfigurable
factor (see Table 3-1 for details).
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
3 Technical Description
The UE's uplink coverage is determined based on the P-CPICH RSCP, which can be obtained
from the periodically reported intra-frequency measurement reports. The
LittleRetranRabRscpPrd parameter in the SET UCHLQUALITYEVALUATE command
specifies the measurement period of the P-CPICH RSCP.
A UE's uplink coverage is not limited if the following conditions are met:
l
For UEs using the 2 ms TTI, the calibrated P-CPICH RSCP is greater than the value of
BeTTI2msRscpUpThd.
For UEs using the 10 ms TTI, the calibrated P-CPICH RSCP is greater than the value of
BeTTI10msRscpUpThd.
For UEs using the 2 ms TTI, the calibrated P-CPICH RSCP is smaller than or equal to the
value of BeTTI2msRscpUpThd.
For UEs using the 10 ms TTI, the calibrated P-CPICH RSCP is smaller than or equal to the
value of BeTTI10msRscpUpThd.
Calibrated P-CPICH RSCP = Reported P-CPICH RSCP (Transmit power on the P-CPICH
33dBm) (RTWP (-105.2 dBm))
If the features HSUPA Adaptive Retransmission and Adaptive Adjustment of HSUPA Small
Target Retransmissions are both enabled and the air interface resources or UE transmit power
on the uplink is limited, the Adaptive Adjustment of HSUPA Small Target Retransmissions
feature selects one UE to use the large target number of retransmissions during each period. If
the selected UE later meets the conditions for using the small target number of retransmissions,
EdchTargetLittleRetransNum or EdchAltTarLittleRetransNum is used based on the setting
for the initial access of an HSUPA UE. For details about these conditions, see the HSUPA
Feature Parameter Description.
10
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
4 Related Features
Related Features
Prerequisite Features
This feature depends on WRFD-010612 HSUPA Introduction Package.
Impacted Features
None
11
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
5 Network Impact
Network Impact
System Capacity
This feature improves the uplink performance. The performance is affected by the uplink
throughput and uplink load and the gain depends on the environment of the commercial network.
It is recommended that this feature be enabled if the uplink load of the cell is restricted and there
are a large number of HSUPA UEs using a 10 ms TTI. If some UEs in the cell are engaged in
continuous uploading, this feature improves the uplink throughput by 10% to 15%. If all services
in the cell are burst services, this feature lowers the RTWP by around 0.5 dB.
When the uplink load of the cell is not restricted and a large number of UEs are processing lowspeed HSUPA services, the RSCP- and RTWP-based Adjustment of HSUPA Small Target
Retransmissions function increases the uplink throughput of the cell by up to about 5% compared
with the RTWP-based Adjustment of HSUPA Small Target Retransmissions function, if some
UEs are continuously performing upload services.
Network PerformanceNone.
No impact.
12
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
Engineering Guidelines
13
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
6.3 Deployment
This section describes how to activate, verify, and deactivate the optional feature WRFD-140222
Adaptive Adjustment of HSUPA Small Target Retransmissions.
6.3.1 Requirements
l
Dependencies on Hardware
None
License
The license for the HSUPA Small Target Adaptive Retransmissions feature has been
activated. For details about the license control item and how to activate the license, see
License Management Feature Parameter Description. Table 6-1 lists the license
information for HSUPA Small Target Adaptive Retransmissions.
Table 6-1 License information for HSUPA Small Target Adaptive Retransmissions
Feature ID
Feature Name
NE
Sales Unit
WRFD-140222
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
Adaptive Adjustment of
HSUPA Small Target
Retransmissions (per kbps)
RNC
per Mbps
14
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
Parameter ID
Setting Notes
Data Source
Power Control
Switch
PcSwitch
To activate the
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
feature, select the
PC_OLPC_SWITC
H,
PC_HSUPA_LITRE
TNUM_INIT_SEL_
SWITCH, and
PC_HSUPA_LITRE
TNUM_AUTO_AD
JUST_SWITCH
check boxes under
this parameter.
RscpEffectAlgoSwitch
To activate the
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
feature, select the
BASE_RSCP_RT
WP_LITRETNUM
_AUTOADJ_SWI
TCH check box
under this parameter.
15
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
Parameter Name
Parameter ID
Setting Notes
Data Source
RSCP INTERVAL
IN RAB FOR
SMALL TARGET
RETRANS
LittleRetranRabRscpPrd
If this parameter is
set to a large value,
the RSCP
measurement period
is long during the
RAB setup, and the
RNC cannot receive
the RSCP in time
during RAB setup.
As a result, the small
target number of
retransmissions
cannot be adjusted in
time when the uplink
load of the cell and
cell coverage are not
limited. The UEs'
HSUPA throughput
is decreased. If this
parameter is set to a
small value, the
RSCP measurement
period is short during
RAB setup, and the
RNC can receive the
RSCP in time.
However, the CPU
usage of the RNC is
significantly
increased.
Default value/
Recommended value
6.3.3 Activation
Using MML Commands
Step 1 (Optional) In the RAN sharing and MOCN scenario, run the RNC MML command SET
LICENSE. In this step, set the value of Adaptive Adjustment of HSUPA Small Target
Retransmissions-kbps for the primary and secondary operators.
Step 2 Run the RNC MML command SET UCORRMALGOSWITCH with
PC_OLPC_SWITCH under Power Control Switch selected to enable outer-loop power
control.
NOTE
You need to activate outer loop power control before activating the Adaptive Adjustment of HSUPA Small
Target Retransmissions feature.
16
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
When configuring the parameter Alter Edch Little Target Number of E-DCH PDU retransfer, the default
value for this parameter is recommended. An inappropriate value for this parameter may lead to decreased cell
throughput. For services with a 5.44 Mbit/s MBR and a 2 ms transmission time interval (TTI), the default value
of this parameter is 0.02. For other services with a 2 ms TTI, the default value of this parameter is 0.01. For
services with a 10 ms TTI, the default value of this parameter is 0.1.
When configuring the Adaptive Adjustment of HSUPA Small Target Retransmissions feature on the CME,
perform a single configuration first, and then perform a batch modification if required.
Configure the parameters of a single object before a batch modification. Perform a batch modification
before logging out of the parameter setting interface.
17
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
MO
NE
Paramete
r Name
Parameter ID
Configu
rable in
CME
Batch
Modific
ation
Center
UCORR
MALGOS
WITCH
RNC
Power
Control
Switch
PcSwitch
Yes
UCHLQU
ALITYE
VALUAT
E
RNC
Switch for
Use
Periodical
Reported
RSCP
RscpEffectAlgoSwitch
RSCP
Interval in
RAB for
Small
Target
Retrans
LittleRetranRabRscpPrd
(Select the
BASE_RSCP_RTWP_LITRET
NUM_AUTOADJ_SWITCH
check box under this parameter.)
18
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
Step 3 On the RNC LMT main page, click Monitor. In the displayed Monitor Navigation Tree pane,
choose Monitor > UMTS Monitoring > Connection Performance Monitoring. The
Connection Performance Monitoring dialog box is displayed. In this dialog box, set Monitor
Item to OLPC, and set IMSI to the same value as that in step 1. Then, check the average number
of transmissions on the E-DCH.
If the average number of retransmissions on the E-DCH (equals the average number of
transmissions on the E-DCH minus one) is close to the larger value between
EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum, this feature has been
activated. For example, the average number of transmissions on the E-DCH is 1.0821, the
average number of retransmissions on the E-DCH is 0.0821, and the default values of
EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum are 0.01 and 0.1,
respectively for UEs using a 10 ms TTI. In this case, the average number of retransmissions on
the E-DCH is close to the value of EdchAltTarLittleRetransNum, and this feature has been
activated.
Step 4 Observe the following counters to see if the feature goes into effect.
l When the RTWP-based Adjustment of HSUPA Small Target Retransmissions function is
enabled, this function has been activated if the values of the counters listed in Table 6-4 are
greater than zero.
l When the RSCP- and RTWP-based Adjustment of HSUPA Small Target Retransmissions
function is enabled, this function has been activated if the values of the counters listed in
Table 6-4 are greater than zero.
Table 6-4 Counters for HSUPA Adaptive Transmission
VS.HSUPA.SmallRs
nAdj.TTI2ms
VS.HSUPA.SmallRs
nAdj.TTI10ms
----End
6.3.5 Deactivation
Using MML Commands
Step 1 Run the RNC MML command SET UCORRMALGOSWITCH. In this step, deselect the
PC_HSUPA_LITRETNUM_INIT_SEL_SWITCH and
PC_HSUPA_LITRETNUM_AUTO_ADJUST_SWITCH check boxes under the Power
Issue Draft A (2014-01-20)
19
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
Control Switch parameter to deactivate the algorithm for selecting an initial small target number
of retransmissions for HSUPA UEs.
Step 2 Run the RNC MML command SET UCHLQUALITYEVALUATE. In this step, deselect the
BASE_RSCP_RTWP_LITRETNUM_AUTOADJ_SWITCH check box under the Switch
for Use Periodical Reported RSCP parameter.
----End
When configuring the Adaptive Adjustment of HSUPA Small Target Retransmissions feature on the CME,
perform a single configuration first, and then perform a batch modification if required.
Configure the parameters of a single object before a batch modification. Perform a batch modification
before logging out of the parameter setting interface.
20
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
MO
NE
Par
am
eter
Na
me
Parameter ID
Co
nfi
gur
abl
e in
CM
E
Bat
ch
Mo
difi
cati
on
Ce
nte
r
UCORRMALGO
SWITCH
RN
C
Pow
er
Con
trol
Swi
tch
PcSwitch
Yes
UCHLQUALITY
EVALUATE
RN
C
Swi
tch
for
Use
Peri
odic
al
Rep
orte
d
RS
CP
RscpEffectAlgoSwitch
(Deselect the
PC_HSUPA_LITRETNUM_INIT_SE
L_SWITCH and
PC_HSUPA_LITRETNUM_AUTO_A
DJUST_SWITCH check boxes under
this parameter.)
No
(Deselect the
BASE_RSCP_RTWP_LITRETNUM_
AUTOADJ_SWITCH check box under
this parameter).
----End
21
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
6 Engineering Guidelines
22
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameters
NE
MML
Command
Feature ID
Feature Name
Description
EdchTargetLittleRetransNum
BSC6900
ADD
UTYPRABOLP
C
WRFD-010612
03
HSUPA Power
Control
Meaning:Numb
er of target
retransmissions
when the MACES data flows
carrying the
service allow
small
retransmissions.
This parameter
is used to
improve the
single user
throughput or
cell throughput
when the cell
load is normal.
Small
retransmission
is configured to
enable HSUPA
users to reach
the uplink peak
rate or obtain the
HARQ
combination
gain.
MOD
UTYPRABOLP
C
GUI Value
Range:0~15000
Unit:None
23
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
Actual Value
Range:0~15,
step: 0.001
Default
Value:None
EdchTargetLittleRetransNum
BSC6910
ADD
UTYPRABOLP
C
WRFD-010612
03
HSUPA Power
Control
MOD
UTYPRABOLP
C
Meaning:Numb
er of target
retransmissions
when the MACES data flows
carrying the
service allow
small
retransmissions.
This parameter
is used to
improve the
single user
throughput or
cell throughput
when the cell
load is normal.
Small
retransmission
is configured to
enable HSUPA
users to reach
the uplink peak
rate or obtain the
HARQ
combination
gain.
GUI Value
Range:0~15000
Unit:None
Actual Value
Range:0~15,
step: 0.001
Default
Value:None
24
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EdchAltTarLittleRetransNum
BSC6900
ADD
UTYPRABOLP
C
WRFD-010612
03
HSUPA Power
Control
Meaning:Numb
er of alternative
small target
retransmissions.
When used with
"EdchTargetLittleRetransNum"
, this parameter
increases single
user throughput
or cell
throughput.
Small
retransmission
is configured to
enable HSUPA
users to reach
the uplink peak
rate or obtain the
HARQ
combination
gain. This
parameter is an
advanced
parameter. To
modify this
parameter,
contact Huawei
Customer
Service Center
for technical
support.
MOD
UTYPRABOLP
C
GUI Value
Range:0~15000
Unit:None
Actual Value
Range:0~15,
step: 0.001
Default
Value:None
25
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EdchAltTarLittleRetransNum
BSC6910
ADD
UTYPRABOLP
C
WRFD-010612
03
HSUPA Power
Control
Meaning:Numb
er of alternative
small target
retransmissions.
When used with
"EdchTargetLittleRetransNum"
, this parameter
increases single
user throughput
or cell
throughput.
Small
retransmission
is configured to
enable HSUPA
users to reach
the uplink peak
rate or obtain the
HARQ
combination
gain. This
parameter is an
advanced
parameter. To
modify this
parameter,
contact Huawei
Customer
Service Center
for technical
support.
MOD
UTYPRABOLP
C
GUI Value
Range:0~15000
Unit:None
Actual Value
Range:0~15,
step: 0.001
Default
Value:None
26
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RscpEffectAlgo
Switch
BSC6900
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Wheth
er to allow
specific
algorithms to
preferentially
use periodical
reported RSCP
values. 1.
BASE_RSCP_
BE_TTI_E2D_I
NITSEL_SWIT
CH: When this
switch is turned
on: If the
DRA_BASE_C
OVER_BE_E2
D_INITSEL_S
WITCH of the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to
perform EDCH-to-DCH
channel fallback
on BE services
during a service
setup. If the
DRA_BASE_C
OVER_BE_TTI
_INIT_SEL_S
WITCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
27
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
RNC
preferentially
uses
periodically
reported RSCP
values to
determine
whether to select
an E-DCH with
2 ms TTI or an
E-DCH with 10
ms TTI for BE
services during a
service setup. If
the
DRA_BASE_C
OVER_BE_E2
D_INITSEL_S
WITCH of the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command and
DRA_BASE_C
OVER_BE_TTI
_INIT_SEL_S
WITCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command are
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to select
an E-DCH with
2/10 ms TTI or
an uplink DCH
for BE services
during a service
setup. 2.
28
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
BASE_RSCP_
BE_TTI_E2D_
RECFG_SWIT
CH: When this
switch is turned
on: If the
DRA_BASE_C
OVER_BE_E2
D_SWITCH of
the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to
perform EDCH-to-DCH
channel fallback
on BE services
after a service
setup. If the
DRA_BASE_C
OVER_BE_TTI
_RECFG_SWI
TCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to
perform 2-to-10
ms TTI
29
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
switching on BE
services after a
service setup. If
the
DRA_BASE_C
OVER_BE_E2
D_SWITCH of
the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command and
DRA_BASE_C
OVER_BE_TTI
_RECFG_SWI
TCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command are
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to select
an E-DCH with
2/10 ms TTI or
an uplink DCH
for BE services
after a service
setup. 3.
BASE_RSCP_
RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH:
Switch for the
RSCP/RTWPbased algorithm
for adaptively
adjusting the
small target
number of
30
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
retransmissions
for HSUPA
UEs. When this
switch is turned
on:If the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
TCH" is turned
on, the small
target number of
retransmissions
for HSUPA UEs
processing a
single PS BE
service equals
the value of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
depending on
the RTWP
reported by the
NodeB and the
RSCP values
periodically
reported during
the interval
between RRC
connection and
RAB setups.If
the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
TCH" is turned
off, the small
target number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter. If the
31
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned on, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
depending on
the RSCP values
periodically
reported after
RAB setups, the
RTWP reported
by the NodeB,
and BE service
throughput
reported by
Layer 2. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned off, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter.
When this
switch is turned
off: If the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
32
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
TCH" is turned
on, the small
target number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
whichever is
larger. If the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
TCH" is turned
off, the small
target number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned on, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
depending on
BE service
throughput
33
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
reported by
Layer 2. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned off, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned off, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter.
GUI Value
Range:BASE_R
SCP_BE_TTI_
E2D_INITSEL_
SWITCH,
BASE_RSCP_
BE_TTI_E2D_
RECFG_SWIT
CH,
BASE_RSCP_
RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH
Unit:None
Actual Value
Range:BASE_R
SCP_BE_TTI_
34
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
E2D_INITSEL_
SWITCH,
BASE_RSCP_
BE_TTI_E2D_
RECFG_SWIT
CH,
BASE_RSCP_
RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH
Default
Value:BASE_R
SCP_BE_TTI_
E2D_INITSEL_
SWITCH:
0,BASE_RSCP
_BE_TTI_E2D
_RECFG_SWI
TCH:
0,BASE_RSCP
_RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH:
0
35
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RscpEffectAlgo
Switch
BSC6910
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Wheth
er to allow
specific
algorithms to
preferentially
use periodical
reported RSCP
values. 1.
BASE_RSCP_
BE_TTI_E2D_I
NITSEL_SWIT
CH: When this
switch is turned
on: If the
DRA_BASE_C
OVER_BE_E2
D_INITSEL_S
WITCH of the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to
perform EDCH-to-DCH
channel fallback
on BE services
during a service
setup. If the
DRA_BASE_C
OVER_BE_TTI
_INIT_SEL_S
WITCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
36
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
RNC
preferentially
uses
periodically
reported RSCP
values to
determine
whether to select
an E-DCH with
2 ms TTI or an
E-DCH with 10
ms TTI for BE
services during a
service setup. If
the
DRA_BASE_C
OVER_BE_E2
D_INITSEL_S
WITCH of the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command and
DRA_BASE_C
OVER_BE_TTI
_INIT_SEL_S
WITCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command are
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to select
an E-DCH with
2/10 ms TTI or
an uplink DCH
for BE services
during a service
setup. 2.
37
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
BASE_RSCP_
BE_TTI_E2D_
RECFG_SWIT
CH: When this
switch is turned
on: If the
DRA_BASE_C
OVER_BE_E2
D_SWITCH of
the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to
perform EDCH-to-DCH
channel fallback
on BE services
after a service
setup. If the
DRA_BASE_C
OVER_BE_TTI
_RECFG_SWI
TCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command is
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to
perform 2-to-10
ms TTI
38
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
switching on BE
services after a
service setup. If
the
DRA_BASE_C
OVER_BE_E2
D_SWITCH of
the
"DraSwitch2"
parameter in the
"SET
UCORRMALG
OSWITCH"
command and
DRA_BASE_C
OVER_BE_TTI
_RECFG_SWI
TCH of the
"DraSwitch"
parameter in the
"SET
UCORRMALG
OSWITCH"
command are
turned on, the
RNC
preferentially
uses
periodically
reported RSCP
values to select
an E-DCH with
2/10 ms TTI or
an uplink DCH
for BE services
after a service
setup. 3.
BASE_RSCP_
RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH:
Switch for the
RSCP/RTWPbased algorithm
for adaptively
adjusting the
small target
number of
39
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
retransmissions
for HSUPA
UEs. When this
switch is turned
on:If the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
TCH" is turned
on, the small
target number of
retransmissions
for HSUPA UEs
processing a
single PS BE
service equals
the value of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
depending on
the RTWP
reported by the
NodeB and the
RSCP values
periodically
reported during
the interval
between RRC
connection and
RAB setups.If
the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
TCH" is turned
off, the small
target number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter. If the
40
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned on, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
depending on
the RSCP values
periodically
reported after
RAB setups, the
RTWP reported
by the NodeB,
and BE service
throughput
reported by
Layer 2. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned off, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter.
When this
switch is turned
off: If the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
41
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
TCH" is turned
on, the small
target number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
whichever is
larger. If the
"PC_HSUPA_L
ITRETNUM_I
NIT_SEL_SWI
TCH" is turned
off, the small
target number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned on, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
or
"EdchAltTarLitt
leRetransNum"
parameter,
depending on
BE service
throughput
42
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
reported by
Layer 2. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned off, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter. If the
"PC_HSUPA_L
ITRETNUM_A
UTO_ADJUST
_SWITCH" is
turned off, the
small target
number of
retransmissions
for these UEs
equals the value
of the
"EdchTargetLittleRetransNum"
parameter.
GUI Value
Range:BASE_R
SCP_BE_TTI_
E2D_INITSEL_
SWITCH,
BASE_RSCP_
BE_TTI_E2D_
RECFG_SWIT
CH,
BASE_RSCP_
RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH
Unit:None
Actual Value
Range:BASE_R
SCP_BE_TTI_
43
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
E2D_INITSEL_
SWITCH,
BASE_RSCP_
BE_TTI_E2D_
RECFG_SWIT
CH,
BASE_RSCP_
RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH
Default
Value:BASE_R
SCP_BE_TTI_
E2D_INITSEL_
SWITCH:
0,BASE_RSCP
_BE_TTI_E2D
_RECFG_SWI
TCH:
0,BASE_RSCP
_RTWP_LITRE
TNUM_AUTO
ADJ_SWITCH:
0
44
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PcSwitch
BSC6900
SET
UCORRMALG
OSWITCH
WRFD-010641
HSUPA
Adaptive
Transmission
Meaning:1.
PC_CFG_ED_P
OWER_INTER
POLATION_S
WITCH: When
the switch is on,
E-DPDCH
power
interpolation
formula is
allowed.
Otherwise,
interpolation
formula is not
allowed. When
the interpolation
formula is used,
E-TFCI and PO
is involved in the
calculation of
transmit power
for block
transmission on
the E-DPDCH.
In addition, the
extrapolation
formula is also
used. the
interpolation
formular is used
for high-speed
services,
whereas the
extrapolation
formula is used
for low-speed
services. For
details about this
parameter, see
3GPP TS
25.214. 2.
PC_DL_INNER
_LOOP_PC_A
CTIVE_SWITC
H: When the
switch is on, the
status of inner
loop DL power
WRFD-140215
WRFD-140222
WRFD-150230
WRFD-020504
WRFD-020502
WRFD-020503
WRFD-020501
WRFD-140216
WRFD-010612
03
WRFD-020138
WRFD-010712
Dynamic
Configuration of
HSDPA CQI
Feedback Period
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
DPCH Pilot
Power
Adjustment
Inner Loop
Power Control
Downlink
Power Balance
Outer Loop
Power Control
Open Loop
Power Control
Load-based
Uplink Target
BLER
Configuration
HSUPA Power
Control
HSUPA
Coverage
Enhancement at
UE power
limitation
Adaptive
Configuration of
Traffic Channel
Power offset for
HSUPA
45
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
control is set to
"Active." When
the switch is not
on, the status is
set to "Inactive."
3.
PC_DOWNLIN
K_POWER_BA
LANCE_SWIT
CH: When the
switch is on, the
RNC supports
DL power
balancing.
During soft
handover, TPC
bit errors cause
DL power drift.
DL power
balancing is
enabled to
balance the DL
power between
links, thus
achieving the
optimal gain of
soft handover. 4.
PC_EFACH_E
CN0_DYN_AD
J_SWITCH:
When the switch
is on, the target
value of Ec/No
can be
dynamically
reconfigured on
the E-FACH.
When the switch
is disabled, the
minimum value
of Ec/No is
directly
configured for
the NodeB. 5.
PC_FP_MULTI
_RLS_IND_SW
ITCH: When the
switch is on, the
46
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
RNC informs
the NodeB of the
current RLS
number through
the FP inband
signaling. 6.
PC_HSUPA_C
OVER_EN_AT
_POLIMIT_SW
ITCH: When the
switch is on, the
HSUPA
Coverage
Improvement
Under Limited
UE Power
algorithm is
used for the
RNC. 7.
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH:
When the switch
is on, the Power
Offset Adaptive
Adjustment on
HSUPA Data
Channel
algorithm is
used for the
RNC. 8.
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH: When
the switch is on,
the HSUPA
service can use a
smaller target
number of
retransmissions
than the typical
value when the
uplink is not
congested. If the
uplink is
congested, the
47
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
HSUPA service
needs to use the
typical target
number of
retransmissions.
9.
PC_INNER_LO
OP_LMTED_P
WR_INC_SWI
TCH: When the
switch is on, the
limited power
increase
function is used
for DL inner
loop power
control. 10.
PC_OLPC_SWI
TCH: When the
switch is on, the
RNC updates
the UL SIR
TARGET of
radio links on
the NodeB side
through IUB
DCH FP inband
signaling. 11.
PC_RL_RECF
G_SIR_TARGE
T_CARRY_SW
ITCH: When the
switch is not on,
a new initial
SIRTarget
value, during
radio link
reconfiguration,
is based on the
converged
SIRTarget value
of current outer
loop power
control. In
addition, the UL
SIRTarget value
is not included in
the radio link
48
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
reconfiguration
messages to the
NodeB. This
switch is only
valid when the
OLPC switch is
ON. 12.
PC_SIG_DCH_
OLPC_SWITC
H: When the
switch is on, SIG
DCH is involved
in UL OLPC as
service DCH is.
If the current
link has only
SIG DCH, SIG
DCH is always
involved in UL
OLPC. 13.
PC_UL_SIRER
R_HIGH_REL_
UE_SWITCH:
When the switch
is on, the UE is
unconditionally
released if the
SIR error is high
and the cell is
overloaded.
Otherwise, the
UE is not
released. 14.
PC_HSUPA_LI
TRETNUM_A
UTO_ADJUST
_SWITCH:
Whether the
RNC adjusts the
target number of
times that a UE
processing a
single PS BE
service performs
retransmission
in the E-DCH
small
retransmission
49
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
state. When this
switch is turned
on, the RNC
chooses
between
"EdchAltTarLitt
leRetransNum"
and
"EdchTargetLittleRetransNum"
as the target
retransmission
number based
on the
throughput
measurement.
When this
switch is turned
off, the target
retransmission
number is
always
"EdchTargetLittleRetransNum"
. 15.
PC_OLPC_FAS
TDOWN_OPTI
MIZE_SWITC
H: Whether to
support the
optimized
algorithm for
Outer Loop
Power Control
(OLPC). When
this switch is
turned on, the
optimized
OLPC algorithm
is supported.
SIRtarget is
adjusted in an
optimized
manner when
interference
bursts out, UE
transmit power
is limited, OLPC
50
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
is being set up,
modified, or
restarted. When
this switch is
turned off, the
optimized
OLPC algorithm
is not supported.
16.
PC_HSUPA_LI
TRETNUM_IN
IT_SEL_SWIT
CH: When this
switch is turned
on, the number
of the initial
target
retransmission
attempts for UEs
in the E-DCH
little
retransmission
state equals the
value of
"EdchAltTarLitt
leRetransNum"
or
"EdchTargetLittleRetransNum"
, whichever is
larger.When this
switch is turned
off, the number
of the initial
target
retransmission
attempts for
such UEs equals
the value of
"EdchTargetLittleRetransNum"
. 17.
PC_CQI_CYCL
E_BASE_CEL
LLOAD_SWIT
CH: Whether to
activate the
load-based
51
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
algorithm for the
CQI feedback
period. The CQI
feedback period
is equal to the
value of
"CQIFBckBaseCellLoad" in the
"SET
UHSDPCCH"
command when
this switch is
turned on,
uplink load in
the cell is heavy,
and BE services
are carried over
the HSDPA. 18.
PC_CQI_CYCL
E_BASE_COV
ERAGE_SWIT
CH: Whether to
activate the
coverage-based
algorithm for the
CQI feedback
period. The CQI
feedback period
is equal to the
value of
"CQIFBckBase
Coverage" in the
"SET
UHSDPCCH"
command when
this switch is
turned on, the
UE moves to the
edge of the cell,
and BE services
are carried over
the HSDPA. 19.
PC_CQI_CYCL
E_BASE_CS_P
LUS_PS_SWIT
CH: Whether to
activate the
combined-
52
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
service-specific
algorithm for the
CQI feedback
period. The CQI
feedback period
is equal to the
value of
"CQIFBckBase
CsCombServ"
in the "SET
UHSDPCCH"
command when
this switch is
turned on and
the UE is
processing CS
and PS services.
In addition, CS
services and PS
services are
carried over the
DCH and
HSDPA,
respectively. 20.
PC_BLER_TA
RGET_BASE_
CELLLOAD_S
WITCH: When
this switch is
turned on, the
target BLER of
the DCH is equal
to the value of
"BlerTargetBas
eCellLoad" in
the "SET
UOLPC"
command if the
uplink cell load
is heavy and
only PS BE
services are
carried over the
DCH. 21.
PC_HSUPA_D
ATA_CH_PO_I
NIT_SEL_SWI
TCH: When this
53
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
switch is turned
on, the RNC sets
the power offset
between the EDPDCH and
DPCCH to the
value of
"HarqPOLitRetr
LRate" in the
"ADD
UTYPRABHS
UPAPC"
command after a
UE is transited
from a state to
the CELL_DCH
state. The
function
controlled by
this switch also
takes effect
during an RAB
setup process.
When this
switch is turned
off, the power
offset is
determined by
the algorithm
controlled by the
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH. If
the
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH is
turned off, the
power offset is
0. 22.
PC_PILOT_PO
_OPTI_SWITC
H: Sets small
pilot power
offset and small
number of bits
54
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
for pilot bits in
case of
downlink cell
non-HSPA
power
congestions to
decrease power
congestions.
When this
switch is turned
on and the
downlink nonHSPA power
resources of the
cell are in a
congestion state
specified by
"LoadStateForP
ilotPwrAdj"("S
ET
UFRC"/"ADD
UCELLFRC")
or higher,
"NonCsOptiPilo
tPo"("SET
UFRC") or
"CsOptiPilotPo"
("SET UFRC")
specifies the
pilot power
offset on the
DPCH. When
the spreading
factor (SF) is
256,
"DlDpchSf256
OptiPilotBit"("S
ET UFRC")
specifies the
number for bits
of pilot bits on
the DPCH.
Regardless of
the switch state,
when the
downlink nonHSPA power
resources of the
55
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
cell are in a
lower
congestion state
than the state
specified by
"LoadStateForP
ilotPwrAdj"("S
ET
UFRC"/"ADD
UCELLFRC"),
"PilotPo"("SET
UFRC")
specifies the
pilot power
offset on the
DPCH. When
the SF is 256,
"DlDpchSf256P
ilotBit"("SET
UFRC")
specifies the
number for bits
of pilot bits on
the DPCH. 23.
PC_HSUPA_L
OWRATE_FLE
XPC_SWITCH:
Switch
controlling the
Flexible Power
Control for
Uplink Low
Data Rate
Transmission
feature. When
this switch is
turned on, this
feature is
activated. When
this switch is
turned off, this
feature is not
activated. 24.
PC_COMB_HS
UPA_LOWRA
TE_FLEXPC_S
WITCH: Switch
controlling the
56
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
Flexible Power
Control for
Uplink Low
Data Rate
Transmission
feature for
combined
services. When
this switch is
turned on, this
feature is
activated for
combined
services. When
this switch is
turned off, this
feature is not
activated for
combined
services. 25.
PC_FP_MULTI
_RLS_IND_SE
ND_TIME_OP
T_SWITCH:
Time at which
the FP control
frame that
carries the
"Multiple RL
Sets Indicator"
is delivered.
When this
switch is set to
on, the RNC
delivers the FP
control frame
that carries the
"Multiple RL
Sets Indicator"
to the NodeB in
any of the
following
scenarios: A
handover is
complete, the
UE initially
enters the
CELL_DCH
57
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
state, or the
RNC sends an
Active Set
Update message
during a singleto-multiple RLS
switch. When
this switch is set
to off, the RNC
delivers the FP
control frame
that carries the
"Multiple RL
Sets Indicator"
to the NodeB
only after a
handover.
GUI Value
Range:PC_DL_
INNER_LOOP
_PC_ACTIVE_
SWITCH,
PC_DOWNLIN
K_POWER_BA
LANCE_SWIT
CH,
PC_EFACH_E
CN0_DYN_AD
J_SWITCH,
PC_FP_MULTI
_RLS_IND_SW
ITCH,
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH,
PC_INNER_LO
OP_LMTED_P
WR_INC_SWI
TCH,
PC_OLPC_SWI
TCH,
PC_RL_RECF
G_SIR_TARGE
T_CARRY_SW
ITCH,
PC_SIG_DCH_
58
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
OLPC_SWITC
H,
PC_UL_SIRER
R_HIGH_REL_
UE_SWITCH,
PC_CFG_ED_P
OWER_INTER
POLATION_S
WITCH,
PC_HSUPA_C
OVER_EN_AT
_POLIMIT_SW
ITCH,
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH,
PC_HSUPA_LI
TRETNUM_A
UTO_ADJUST
_SWITCH,
PC_OLPC_FAS
TDOWN_OPTI
MIZE_SWITC
H,
PC_HSUPA_LI
TRETNUM_IN
IT_SEL_SWIT
CH,
PC_CQI_CYCL
E_BASE_CEL
LLOAD_SWIT
CH,
PC_CQI_CYCL
E_BASE_COV
ERAGE_SWIT
CH,
PC_CQI_CYCL
E_BASE_CS_P
LUS_PS_SWIT
CH,
PC_BLER_TA
RGET_BASE_
CELLLOAD_S
WITCH,
PC_HSUPA_D
ATA_CH_PO_I
NIT_SEL_SWI
59
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
TCH,
PC_PILOT_PO
_OPTI_SWITC
H,
PC_HSUPA_L
OWRATE_FLE
XPC_SWITCH,
PC_COMB_HS
UPA_LOWRA
TE_FLEXPC_S
WITCH,
PC_FP_MULTI
_RLS_IND_SE
ND_TIME_OP
T_SWITCH
Unit:None
Actual Value
Range:PC_CFG
_ED_POWER_
INTERPOLATI
ON_SWITCH,
PC_DL_INNER
_LOOP_PC_A
CTIVE_SWITC
H,
PC_DOWNLIN
K_POWER_BA
LANCE_SWIT
CH,
PC_EFACH_E
CN0_DYN_AD
J_SWITCH,
PC_FP_MULTI
_RLS_IND_SW
ITCH,
PC_HSUPA_C
OVER_EN_AT
_POLIMIT_SW
ITCH,
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH,
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH,
60
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
PC_INNER_LO
OP_LMTED_P
WR_INC_SWI
TCH,
PC_OLPC_SWI
TCH,
PC_RL_RECF
G_SIR_TARGE
T_CARRY_SW
ITCH,
PC_SIG_DCH_
OLPC_SWITC
H,
PC_UL_SIRER
R_HIGH_REL_
UE_SWITCH,
PC_HSUPA_LI
TRETNUM_A
UTO_ADJUST
_SWITCH,
PC_OLPC_FAS
TDOWN_OPTI
MIZE_SWITC
H,
PC_HSUPA_LI
TRETNUM_IN
IT_SEL_SWIT
CH,
PC_CQI_CYCL
E_BASE_CEL
LLOAD_SWIT
CH,
PC_CQI_CYCL
E_BASE_COV
ERAGE_SWIT
CH,
PC_CQI_CYCL
E_BASE_CS_P
LUS_PS_SWIT
CH,
PC_BLER_TA
RGET_BASE_
CELLLOAD_S
WITCH,
PC_HSUPA_D
ATA_CH_PO_I
NIT_SEL_SWI
TCH,
61
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
PC_PILOT_PO
_OPTI_SWITC
H,
PC_HSUPA_L
OWRATE_FLE
XPC_SWITCH,
PC_COMB_HS
UPA_LOWRA
TE_FLEXPC_S
WITCH,
PC_FP_MULTI
_RLS_IND_SE
ND_TIME_OP
T_SWITCH
Default
Value:PC_CFG
_ED_POWER_
INTERPOLATI
ON_SWITCH:
0,PC_DL_INN
ER_LOOP_PC_
ACTIVE_SWIT
CH:
1,PC_DOWNLI
NK_POWER_B
ALANCE_SWI
TCH:
1,PC_EFACH_
ECN0_DYN_A
DJ_SWITCH:
0,PC_FP_MUL
TI_RLS_IND_S
WITCH:
1,PC_HSUPA_
COVER_EN_A
T_POLIMIT_S
WITCH:
0,PC_HSUPA_
DATA_CH_PO
_ADAPTIVE_
ADJ_SWITCH:
0,
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH:
0,PC_INNER_
62
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
LOOP_LMTED
_PWR_INC_S
WITCH:
0,PC_OLPC_S
WITCH:
1,PC_RL_REC
FG_SIR_TARG
ET_CARRY_S
WITCH:
1,PC_SIG_DC
H_OLPC_SWI
TCH:
0,PC_UL_SIRE
RR_HIGH_RE
L_UE_SWITC
H:
0,PC_HSUPA_
LITRETNUM_
AUTO_ADJUS
T_SWITCH:
0,PC_OLPC_F
ASTDOWN_O
PTIMIZE_SWI
TCH:
0,PC_HSUPA_
LITRETNUM_I
NIT_SEL_SWI
TCH:
0,PC_CQI_CY
CLE_BASE_C
ELLLOAD_SW
ITCH:
0,PC_CQI_CY
CLE_BASE_C
OVERAGE_S
WITCH:
0,PC_CQI_CY
CLE_BASE_C
S_PLUS_PS_S
WITCH:
0,PC_BLER_T
ARGET_BASE
_CELLLOAD_
SWITCH:
0,PC_HSUPA_
DATA_CH_PO
_INIT_SEL_S
WITCH:
63
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
0,PC_PILOT_P
O_OPTI_SWIT
CH:
0,PC_HSUPA_
LOWRATE_FL
EXPC_SWITC
H:
0,PC_COMB_
HSUPA_LOW
RATE_FLEXP
C_SWITCH:
0,PC_FP_MUL
TI_RLS_IND_S
END_TIME_O
PT_SWITCH:1
64
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PcSwitch
BSC6910
SET
UCORRMALG
OSWITCH
WRFD-010641
HSUPA
Adaptive
Transmission
Meaning:1.
PC_CFG_ED_P
OWER_INTER
POLATION_S
WITCH: When
the switch is on,
E-DPDCH
power
interpolation
formula is
allowed.
Otherwise,
interpolation
formula is not
allowed. When
the interpolation
formula is used,
E-TFCI and PO
is involved in the
calculation of
transmit power
for block
transmission on
the E-DPDCH.
In addition, the
extrapolation
formula is also
used. the
interpolation
formular is used
for high-speed
services,
whereas the
extrapolation
formula is used
for low-speed
services. For
details about this
parameter, see
3GPP TS
25.214. 2.
PC_DL_INNER
_LOOP_PC_A
CTIVE_SWITC
H: When the
switch is on, the
status of inner
loop DL power
WRFD-140215
WRFD-140222
WRFD-150230
WRFD-020504
WRFD-020502
WRFD-020503
WRFD-020501
WRFD-140216
WRFD-010612
03
WRFD-020138
WRFD-010712
Dynamic
Configuration of
HSDPA CQI
Feedback Period
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
DPCH Pilot
Power
Adjustment
Inner Loop
Power Control
Downlink
Power Balance
Outer Loop
Power Control
Open Loop
Power Control
Load-based
Uplink Target
BLER
Configuration
HSUPA Power
Control
HSUPA
Coverage
Enhancement at
UE power
limitation
Adaptive
Configuration of
Traffic Channel
Power offset for
HSUPA
65
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
control is set to
"Active." When
the switch is not
on, the status is
set to "Inactive."
3.
PC_DOWNLIN
K_POWER_BA
LANCE_SWIT
CH: When the
switch is on, the
RNC supports
DL power
balancing.
During soft
handover, TPC
bit errors cause
DL power drift.
DL power
balancing is
enabled to
balance the DL
power between
links, thus
achieving the
optimal gain of
soft handover. 4.
PC_EFACH_E
CN0_DYN_AD
J_SWITCH:
When the switch
is on, the target
value of Ec/No
can be
dynamically
reconfigured on
the E-FACH.
When the switch
is disabled, the
minimum value
of Ec/No is
directly
configured for
the NodeB. 5.
PC_FP_MULTI
_RLS_IND_SW
ITCH: When the
switch is on, the
66
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
RNC informs
the NodeB of the
current RLS
number through
the FP inband
signaling. 6.
PC_HSUPA_C
OVER_EN_AT
_POLIMIT_SW
ITCH: When the
switch is on, the
HSUPA
Coverage
Improvement
Under Limited
UE Power
algorithm is
used for the
RNC. 7.
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH:
When the switch
is on, the Power
Offset Adaptive
Adjustment on
HSUPA Data
Channel
algorithm is
used for the
RNC. 8.
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH: When
the switch is on,
the HSUPA
service can use a
smaller target
number of
retransmissions
than the typical
value when the
uplink is not
congested. If the
uplink is
congested, the
67
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
HSUPA service
needs to use the
typical target
number of
retransmissions.
9.
PC_INNER_LO
OP_LMTED_P
WR_INC_SWI
TCH: When the
switch is on, the
limited power
increase
function is used
for DL inner
loop power
control. 10.
PC_OLPC_SWI
TCH: When the
switch is on, the
RNC updates
the UL SIR
TARGET of
radio links on
the NodeB side
through IUB
DCH FP inband
signaling. 11.
PC_RL_RECF
G_SIR_TARGE
T_CARRY_SW
ITCH: When the
switch is not on,
a new initial
SIRTarget
value, during
radio link
reconfiguration,
is based on the
converged
SIRTarget value
of current outer
loop power
control. In
addition, the UL
SIRTarget value
is not included in
the radio link
68
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
reconfiguration
messages to the
NodeB. This
switch is only
valid when the
OLPC switch is
ON. 12.
PC_SIG_DCH_
OLPC_SWITC
H: When the
switch is on, SIG
DCH is involved
in UL OLPC as
service DCH is.
If the current
link has only
SIG DCH, SIG
DCH is always
involved in UL
OLPC. 13.
PC_UL_SIRER
R_HIGH_REL_
UE_SWITCH:
When the switch
is on, the UE is
unconditionally
released if the
SIR error is high
and the cell is
overloaded.
Otherwise, the
UE is not
released. 14.
PC_HSUPA_LI
TRETNUM_A
UTO_ADJUST
_SWITCH:
Whether the
RNC adjusts the
target number of
times that a UE
processing a
single PS BE
service performs
retransmission
in the E-DCH
small
retransmission
69
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
state. When this
switch is turned
on, the RNC
chooses
between
"EdchAltTarLitt
leRetransNum"
and
"EdchTargetLittleRetransNum"
as the target
retransmission
number based
on the
throughput
measurement.
When this
switch is turned
off, the target
retransmission
number is
always
"EdchTargetLittleRetransNum"
. 15.
PC_OLPC_FAS
TDOWN_OPTI
MIZE_SWITC
H: Whether to
support the
optimized
algorithm for
Outer Loop
Power Control
(OLPC). When
this switch is
turned on, the
optimized
OLPC algorithm
is supported.
SIRtarget is
adjusted in an
optimized
manner when
interference
bursts out, UE
transmit power
is limited, OLPC
70
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
is being set up,
modified, or
restarted. When
this switch is
turned off, the
optimized
OLPC algorithm
is not supported.
16.
PC_HSUPA_LI
TRETNUM_IN
IT_SEL_SWIT
CH: When this
switch is turned
on, the number
of the initial
target
retransmission
attempts for UEs
in the E-DCH
little
retransmission
state equals the
value of
"EdchAltTarLitt
leRetransNum"
or
"EdchTargetLittleRetransNum"
, whichever is
larger.When this
switch is turned
off, the number
of the initial
target
retransmission
attempts for
such UEs equals
the value of
"EdchTargetLittleRetransNum"
. 17.
PC_CQI_CYCL
E_BASE_CEL
LLOAD_SWIT
CH: Whether to
activate the
load-based
71
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
algorithm for the
CQI feedback
period. The CQI
feedback period
is equal to the
value of
"CQIFBckBaseCellLoad" in the
"SET
UHSDPCCH"
command when
this switch is
turned on,
uplink load in
the cell is heavy,
and BE services
are carried over
the HSDPA. 18.
PC_CQI_CYCL
E_BASE_COV
ERAGE_SWIT
CH: Whether to
activate the
coverage-based
algorithm for the
CQI feedback
period. The CQI
feedback period
is equal to the
value of
"CQIFBckBase
Coverage" in the
"SET
UHSDPCCH"
command when
this switch is
turned on, the
UE moves to the
edge of the cell,
and BE services
are carried over
the HSDPA. 19.
PC_CQI_CYCL
E_BASE_CS_P
LUS_PS_SWIT
CH: Whether to
activate the
combined-
72
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
service-specific
algorithm for the
CQI feedback
period. The CQI
feedback period
is equal to the
value of
"CQIFBckBase
CsCombServ"
in the "SET
UHSDPCCH"
command when
this switch is
turned on and
the UE is
processing CS
and PS services.
In addition, CS
services and PS
services are
carried over the
DCH and
HSDPA,
respectively. 20.
PC_BLER_TA
RGET_BASE_
CELLLOAD_S
WITCH: When
this switch is
turned on, the
target BLER of
the DCH is equal
to the value of
"BlerTargetBas
eCellLoad" in
the "SET
UOLPC"
command if the
uplink cell load
is heavy and
only PS BE
services are
carried over the
DCH. 21.
PC_HSUPA_D
ATA_CH_PO_I
NIT_SEL_SWI
TCH: When this
73
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
switch is turned
on, the RNC sets
the power offset
between the EDPDCH and
DPCCH to the
value of
"HarqPOLitRetr
LRate" in the
"ADD
UTYPRABHS
UPAPC"
command after a
UE is transited
from a state to
the CELL_DCH
state. The
function
controlled by
this switch also
takes effect
during an RAB
setup process.
When this
switch is turned
off, the power
offset is
determined by
the algorithm
controlled by the
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH. If
the
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH is
turned off, the
power offset is
0. 22.
PC_PILOT_PO
_OPTI_SWITC
H: Sets small
pilot power
offset and small
number of bits
74
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
for pilot bits in
case of
downlink cell
non-HSPA
power
congestions to
decrease power
congestions.
When this
switch is turned
on and the
downlink nonHSPA power
resources of the
cell are in a
congestion state
specified by
"LoadStateForP
ilotPwrAdj"("S
ET
UFRC"/"ADD
UCELLFRC")
or higher,
"NonCsOptiPilo
tPo"("SET
UFRC") or
"CsOptiPilotPo"
("SET UFRC")
specifies the
pilot power
offset on the
DPCH. When
the spreading
factor (SF) is
256,
"DlDpchSf256
OptiPilotBit"("S
ET UFRC")
specifies the
number for bits
of pilot bits on
the DPCH.
Regardless of
the switch state,
when the
downlink nonHSPA power
resources of the
75
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
cell are in a
lower
congestion state
than the state
specified by
"LoadStateForP
ilotPwrAdj"("S
ET
UFRC"/"ADD
UCELLFRC"),
"PilotPo"("SET
UFRC")
specifies the
pilot power
offset on the
DPCH. When
the SF is 256,
"DlDpchSf256P
ilotBit"("SET
UFRC")
specifies the
number for bits
of pilot bits on
the DPCH. 23.
PC_HSUPA_L
OWRATE_FLE
XPC_SWITCH:
Switch
controlling the
Flexible Power
Control for
Uplink Low
Data Rate
Transmission
feature. When
this switch is
turned on, this
feature is
activated. When
this switch is
turned off, this
feature is not
activated. 24.
PC_COMB_HS
UPA_LOWRA
TE_FLEXPC_S
WITCH: Switch
controlling the
76
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
Flexible Power
Control for
Uplink Low
Data Rate
Transmission
feature for
combined
services. When
this switch is
turned on, this
feature is
activated for
combined
services. When
this switch is
turned off, this
feature is not
activated for
combined
services. 25.
PC_FP_MULTI
_RLS_IND_SE
ND_TIME_OP
T_SWITCH:
Time at which
the FP control
frame that
carries the
"Multiple RL
Sets Indicator"
is delivered.
When this
switch is set to
on, the RNC
delivers the FP
control frame
that carries the
"Multiple RL
Sets Indicator"
to the NodeB in
any of the
following
scenarios: A
handover is
complete, the
UE initially
enters the
CELL_DCH
77
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
state, or the
RNC sends an
Active Set
Update message
during a singleto-multiple RLS
switch. When
this switch is set
to off, the RNC
delivers the FP
control frame
that carries the
"Multiple RL
Sets Indicator"
to the NodeB
only after a
handover.
GUI Value
Range:PC_DL_
INNER_LOOP
_PC_ACTIVE_
SWITCH,
PC_DOWNLIN
K_POWER_BA
LANCE_SWIT
CH,
PC_EFACH_E
CN0_DYN_AD
J_SWITCH,
PC_FP_MULTI
_RLS_IND_SW
ITCH,
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH,
PC_INNER_LO
OP_LMTED_P
WR_INC_SWI
TCH,
PC_OLPC_SWI
TCH,
PC_RL_RECF
G_SIR_TARGE
T_CARRY_SW
ITCH,
PC_SIG_DCH_
78
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
OLPC_SWITC
H,
PC_UL_SIRER
R_HIGH_REL_
UE_SWITCH,
PC_CFG_ED_P
OWER_INTER
POLATION_S
WITCH,
PC_HSUPA_C
OVER_EN_AT
_POLIMIT_SW
ITCH,
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH,
PC_HSUPA_LI
TRETNUM_A
UTO_ADJUST
_SWITCH,
PC_OLPC_FAS
TDOWN_OPTI
MIZE_SWITC
H,
PC_HSUPA_LI
TRETNUM_IN
IT_SEL_SWIT
CH,
PC_CQI_CYCL
E_BASE_CEL
LLOAD_SWIT
CH,
PC_CQI_CYCL
E_BASE_COV
ERAGE_SWIT
CH,
PC_CQI_CYCL
E_BASE_CS_P
LUS_PS_SWIT
CH,
PC_BLER_TA
RGET_BASE_
CELLLOAD_S
WITCH,
PC_HSUPA_D
ATA_CH_PO_I
NIT_SEL_SWI
79
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
TCH,
PC_PILOT_PO
_OPTI_SWITC
H,
PC_HSUPA_L
OWRATE_FLE
XPC_SWITCH,
PC_COMB_HS
UPA_LOWRA
TE_FLEXPC_S
WITCH,
PC_FP_MULTI
_RLS_IND_SE
ND_TIME_OP
T_SWITCH
Unit:None
Actual Value
Range:PC_CFG
_ED_POWER_
INTERPOLATI
ON_SWITCH,
PC_DL_INNER
_LOOP_PC_A
CTIVE_SWITC
H,
PC_DOWNLIN
K_POWER_BA
LANCE_SWIT
CH,
PC_EFACH_E
CN0_DYN_AD
J_SWITCH,
PC_FP_MULTI
_RLS_IND_SW
ITCH,
PC_HSUPA_C
OVER_EN_AT
_POLIMIT_SW
ITCH,
PC_HSUPA_D
ATA_CH_PO_
ADAPTIVE_A
DJ_SWITCH,
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH,
80
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
PC_INNER_LO
OP_LMTED_P
WR_INC_SWI
TCH,
PC_OLPC_SWI
TCH,
PC_RL_RECF
G_SIR_TARGE
T_CARRY_SW
ITCH,
PC_SIG_DCH_
OLPC_SWITC
H,
PC_UL_SIRER
R_HIGH_REL_
UE_SWITCH,
PC_HSUPA_LI
TRETNUM_A
UTO_ADJUST
_SWITCH,
PC_OLPC_FAS
TDOWN_OPTI
MIZE_SWITC
H,
PC_HSUPA_LI
TRETNUM_IN
IT_SEL_SWIT
CH,
PC_CQI_CYCL
E_BASE_CEL
LLOAD_SWIT
CH,
PC_CQI_CYCL
E_BASE_COV
ERAGE_SWIT
CH,
PC_CQI_CYCL
E_BASE_CS_P
LUS_PS_SWIT
CH,
PC_BLER_TA
RGET_BASE_
CELLLOAD_S
WITCH,
PC_HSUPA_D
ATA_CH_PO_I
NIT_SEL_SWI
TCH,
81
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
PC_PILOT_PO
_OPTI_SWITC
H,
PC_HSUPA_L
OWRATE_FLE
XPC_SWITCH,
PC_COMB_HS
UPA_LOWRA
TE_FLEXPC_S
WITCH,
PC_FP_MULTI
_RLS_IND_SE
ND_TIME_OP
T_SWITCH
Default
Value:PC_CFG
_ED_POWER_
INTERPOLATI
ON_SWITCH:
0,PC_DL_INN
ER_LOOP_PC_
ACTIVE_SWIT
CH:
1,PC_DOWNLI
NK_POWER_B
ALANCE_SWI
TCH:
1,PC_EFACH_
ECN0_DYN_A
DJ_SWITCH:
0,PC_FP_MUL
TI_RLS_IND_S
WITCH:
1,PC_HSUPA_
COVER_EN_A
T_POLIMIT_S
WITCH:
0,PC_HSUPA_
DATA_CH_PO
_ADAPTIVE_
ADJ_SWITCH:
0,
PC_HSUPA_H
ARQNUM_AU
TO_ADJUST_S
WITCH:
0,PC_INNER_
82
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
LOOP_LMTED
_PWR_INC_S
WITCH:
0,PC_OLPC_S
WITCH:
1,PC_RL_REC
FG_SIR_TARG
ET_CARRY_S
WITCH:
1,PC_SIG_DC
H_OLPC_SWI
TCH:
0,PC_UL_SIRE
RR_HIGH_RE
L_UE_SWITC
H:
0,PC_HSUPA_
LITRETNUM_
AUTO_ADJUS
T_SWITCH:
0,PC_OLPC_F
ASTDOWN_O
PTIMIZE_SWI
TCH:
0,PC_HSUPA_
LITRETNUM_I
NIT_SEL_SWI
TCH:
0,PC_CQI_CY
CLE_BASE_C
ELLLOAD_SW
ITCH:
0,PC_CQI_CY
CLE_BASE_C
OVERAGE_S
WITCH:
0,PC_CQI_CY
CLE_BASE_C
S_PLUS_PS_S
WITCH:
0,PC_BLER_T
ARGET_BASE
_CELLLOAD_
SWITCH:
0,PC_HSUPA_
DATA_CH_PO
_INIT_SEL_S
WITCH:
83
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
0,PC_PILOT_P
O_OPTI_SWIT
CH:
0,PC_HSUPA_
LOWRATE_FL
EXPC_SWITC
H:
0,PC_COMB_
HSUPA_LOW
RATE_FLEXP
C_SWITCH:
0,PC_FP_MUL
TI_RLS_IND_S
END_TIME_O
PT_SWITCH:1
MaxTargetUlLo
adFactor
BSC6900
ADD
UCELLHSUPA
WRFD-140222
MOD
UCELLHSUPA
WRFD-010612
03
WRFD-140211
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
Dynamic Target
RoT Adjustment
HSUPA Power
Control
Meaning:The
parameter sets
the target value
of the uplink
load. HSUPA
power control
on the NodeB
side keeps
uplink load
close to the
target value. For
details about this
parameter, see
3GPP TS
25.433.
GUI Value
Range:0~100
Unit:%
Actual Value
Range:0~100
Default Value:
75
84
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
MaxTargetUlLo
adFactor
BSC6910
ADD
UCELLHSUPA
WRFD-140222
MOD
UCELLHSUPA
WRFD-010612
03
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
Meaning:The
parameter sets
the target value
of the uplink
load. HSUPA
power control
on the NodeB
side keeps
uplink load
close to the
target value. For
details about this
parameter, see
3GPP TS
25.433.
WRFD-140211
Dynamic Target
RoT Adjustment
HSUPA Power
Control
GUI Value
Range:0~100
Unit:%
Actual Value
Range:0~100
Default Value:
75
85
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RelRatioforUlRTWP
BSC6900
ADD
UCELLLDM
WRFD-020102
Load
Measurement
MOD
UCELLLDM
WRFD-140216
Meaning:Thresh
old ratio for
releasing the
uplink load
restricted state.
If the load for the
TTI switchover
algorithm is in
the restricted
state, the load
switches to the
normal state
when the realtime uplink load
factor of cell is
smaller than the
product of
"MaxTargetUlLoadFactor" and
the value of this
parameter. The
recommended
value difference
between
"RelRatioforUlRTWP" and
"TrigRatioforUlRTWP" is
higher than 10%
because the load
fluctuates.
Otherwise, the
uplink load
frequently
enters and
leaves the
restricted state.
This parameter
is an advanced
parameter. To
modify this
parameter,
contact Huawei
Customer
Service Center
for technical
support.
WRFD-140222
WRFD-140215
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
Load-based
Uplink Target
BLER
Configuration
Dynamic
Configuration of
HSDPA CQI
Feedback Period
86
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
GUI Value
Range:0~100
Unit:%
Actual Value
Range:0~100
Default Value:
60
87
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RelRatioforUlRTWP
BSC6910
ADD
UCELLLDM
WRFD-020102
Load
Measurement
MOD
UCELLLDM
WRFD-140216
Meaning:Thresh
old ratio for
releasing the
uplink load
restricted state.
If the load for the
TTI switchover
algorithm is in
the restricted
state, the load
switches to the
normal state
when the realtime uplink load
factor of cell is
smaller than the
product of
"MaxTargetUlLoadFactor" and
the value of this
parameter. The
recommended
value difference
between
"RelRatioforUlRTWP" and
"TrigRatioforUlRTWP" is
higher than 10%
because the load
fluctuates.
Otherwise, the
uplink load
frequently
enters and
leaves the
restricted state.
This parameter
is an advanced
parameter. To
modify this
parameter,
contact Huawei
Customer
Service Center
for technical
support.
WRFD-140222
WRFD-140215
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
Load-based
Uplink Target
BLER
Configuration
Dynamic
Configuration of
HSDPA CQI
Feedback Period
88
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
GUI Value
Range:0~100
Unit:%
Actual Value
Range:0~100
Default Value:
60
RrcRscpPeriodTimer
BSC6900
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Interv
al for UEs to
report the RSCP
during the
interval between
RRC connection
setup and RAB
assignment
GUI Value
Range:D250,
D500, D1000,
D2000, D3000,
D4000, D6000,
D8000, D12000,
D16000,
D20000,
D24000,
D28000,
D32000,
D64000
Unit:0.25s
Actual Value
Range:250, 500,
1000, 2000,
3000, 4000,
6000, 8000,
12000, 16000,
20000, 24000,
28000, 32000,
64000
Default
Value:D500
89
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RrcRscpPeriodTimer
BSC6910
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Interv
al for UEs to
report the RSCP
during the
interval between
RRC connection
setup and RAB
assignment
GUI Value
Range:D250,
D500, D1000,
D2000, D3000,
D4000, D6000,
D8000, D12000,
D16000,
D20000,
D24000,
D28000,
D32000,
D64000
Unit:0.25s
Actual Value
Range:250, 500,
1000, 2000,
3000, 4000,
6000, 8000,
12000, 16000,
20000, 24000,
28000, 32000,
64000
Default
Value:D500
90
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EcN0EffectTim
e
BSC6900
SET UFRC
WRFD-010510
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Meaning:Time
period for valid
Ec/No or RSCP.
This parameter
defines the time
period during
which the
reported values
of Ec/No or
RSCP are
considered as
valid values.
The time period
starts from the
time the system
receives the first
Ec/No or RSCP.
WRFD-010690
WRFD-010507
WRFD-150232
WRFD-010612
WRFD-020400
GUI Value
Range:0~65535
Unit:ms
Actual Value
Range:0~65535
Default Value:
5000
91
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EcN0EffectTim
e
BSC6910
SET UFRC
WRFD-010510
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Meaning:Time
period for valid
Ec/No or RSCP.
This parameter
defines the time
period during
which the
reported values
of Ec/No or
RSCP are
considered as
valid values.
The time period
starts from the
time the system
receives the first
Ec/No or RSCP.
WRFD-010690
WRFD-010507
WRFD-150232
WRFD-010612
WRFD-020400
GUI Value
Range:0~65535
Unit:ms
Actual Value
Range:0~65535
Default Value:
5000
92
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
BeTTI2msRscp
UpThd
BSC6900
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Upper
RSCP threshold
for the RNC to
determine
whether to
allocate an EDCH with 2 ms
TTI to BE
services after a
service setup.
When the
revised RSCP of
the best cell
exceeds this
threshold, the
RNC
dynamically
allocates an EDCH with 2 ms
TTI to BE
services that
meet the
requirements of
2 ms TTI after a
service setup.
The revised
RSCP of the best
cell can be
calculated using
the following
formula:
Revised RSCP =
Reported RSCP
- (CPICH
transmit power 33dBm) (RTWP +
105.2dBm)
GUI Value
Range:-115~-25
Unit:dBm
Actual Value
Range:-115~-25
Default
Value:-90
93
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
BeTTI2msRscp
UpThd
BSC6910
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Upper
RSCP threshold
for the RNC to
determine
whether to
allocate an EDCH with 2 ms
TTI to BE
services after a
service setup.
When the
revised RSCP of
the best cell
exceeds this
threshold, the
RNC
dynamically
allocates an EDCH with 2 ms
TTI to BE
services that
meet the
requirements of
2 ms TTI after a
service setup.
The revised
RSCP of the best
cell can be
calculated using
the following
formula:
Revised RSCP =
Reported RSCP
- (CPICH
transmit power 33dBm) (RTWP +
105.2dBm)
GUI Value
Range:-115~-25
Unit:dBm
Actual Value
Range:-115~-25
Default
Value:-90
94
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
BeTTI10msRsc
pUpThd
BSC6900
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Upper
RSCP threshold
for the RNC to
determine
whether to
allocate an EDCH with 10 ms
TTI to BE
services after a
service setup.
When the
revised RSCP of
the best cell
exceeds this
threshold, the
RNC
dynamically
allocates an EDCH with 10 ms
TTI to BE
services that
meet the
requirements of
10 ms TTI after
a service setup.
The revised
RSCP of the best
cell can be
calculated using
the following
formula:
Revised RSCP =
Reported RSCP
- (CPICH
transmit power 33dBm) (RTWP +
105.2dBm)
GUI Value
Range:-115~-25
Unit:dBm
Actual Value
Range:-115~-25
Default
Value:-100
95
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
BeTTI10msRsc
pUpThd
BSC6910
SET
UCHLQUALIT
YEVALUATE
WRFD-010690
Meaning:Upper
RSCP threshold
for the RNC to
determine
whether to
allocate an EDCH with 10 ms
TTI to BE
services after a
service setup.
When the
revised RSCP of
the best cell
exceeds this
threshold, the
RNC
dynamically
allocates an EDCH with 10 ms
TTI to BE
services that
meet the
requirements of
10 ms TTI after
a service setup.
The revised
RSCP of the best
cell can be
calculated using
the following
formula:
Revised RSCP =
Reported RSCP
- (CPICH
transmit power 33dBm) (RTWP +
105.2dBm)
GUI Value
Range:-115~-25
Unit:dBm
Actual Value
Range:-115~-25
Default
Value:-100
96
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EcN0ThsFor2m
sTo10ms
BSC6900
SET UFRC
WRFD-010690
Meaning:Ec/N0
threshold for
allocating a 10
ms TTI to
HSUPA UEs
processing BE
services over
uplink
DPDCHs. When
conditions for
allocating a 2 ms
TTI to an
HSUPA UE
processing BE
services over an
uplink DPDCH
have been met,
the RNC
allocates the UE
a 10 ms TTI if
the Ec/N0
reported by the
UE to the RNC
is equal to or
lower than this
threshold. If
DRA_BASE_C
OVER_BE_E2
D_INITSEL_O
PT_SWITCH in
"DraSwitch2" of
the "SET
UCORRMALG
OSWITCH"
command is
turned on, the
algorithm
controlled by
this switch starts
operating earlier
than the
coverage-based
initial TTI
selection
algorithm
specific to BE
services.
97
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
GUI Value
Range:0~49
Unit:0.5dB
Actual Value
Range:-24.5~0
Default Value:
37
98
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EcN0ThsFor2m
sTo10ms
BSC6910
SET UFRC
WRFD-010690
Meaning:Ec/N0
threshold for
allocating a 10
ms TTI to
HSUPA UEs
processing BE
services over
uplink
DPDCHs. When
conditions for
allocating a 2 ms
TTI to an
HSUPA UE
processing BE
services over an
uplink DPDCH
have been met,
the RNC
allocates the UE
a 10 ms TTI if
the Ec/N0
reported by the
UE to the RNC
is equal to or
lower than this
threshold. If
DRA_BASE_C
OVER_BE_E2
D_INITSEL_O
PT_SWITCH in
"DraSwitch2" of
the "SET
UCORRMALG
OSWITCH"
command is
turned on, the
algorithm
controlled by
this switch starts
operating earlier
than the
coverage-based
initial TTI
selection
algorithm
specific to BE
services.
99
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
GUI Value
Range:0~49
Unit:0.5dB
Actual Value
Range:-24.5~0
Default Value:
37
EcN0ThdForBa
seCoverE2D
BSC6900
SET UFRC
WRFD-010510
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Meaning:Ec/No
threshold for an
uplink channel
switch from EDCHs to DCHs
under weak
coverage when a
UE establishes
BE services or
transits from
URA_PCH,
CELL_PCH or
CELL_FACH to
CELL_DCH. If
the HSUPA
bearer policy is
met and the Ec/
No of the target
cell in the
RACH
measurement
report is smaller
than or equal to
this threshold,
the uplink BE
services are
carried from EDCHs to DCHs.
For details, see
3GPP TS
25.215.
GUI Value
Range:0~49
Unit:0.5dB
Actual Value
Range:-24.5~0
Default Value:
25
100
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EcN0ThdForBa
seCoverE2D
BSC6910
SET UFRC
WRFD-010510
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Meaning:Ec/No
threshold for an
uplink channel
switch from EDCHs to DCHs
under weak
coverage when a
UE establishes
BE services or
transits from
URA_PCH,
CELL_PCH or
CELL_FACH to
CELL_DCH. If
the HSUPA
bearer policy is
met and the Ec/
No of the target
cell in the
RACH
measurement
report is smaller
than or equal to
this threshold,
the uplink BE
services are
carried from EDCHs to DCHs.
For details, see
3GPP TS
25.215.
GUI Value
Range:0~49
Unit:0.5dB
Actual Value
Range:-24.5~0
Default Value:
25
101
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
FakeEcNo
BSC6900
SET UFRC
WRFD-010690
Meaning:Substit
ute of the realtime P-CPICH
Ec/N0 when a
UE establishes a
service or
transits from the
CELL_FACH
or CELL_PCH
state to the
CELL_DCH
state and the
RNC does not
receive the PCPICH Ec/N0
value reported
by the UE or the
P-CPICH Ec/N0
value reported
by the UE after
the period
specified by the
EcN0EffectTim
e parameter
expires. This
parameter is
used for
determining
whether UEs are
under weak
coverage in the
following
algorithms:
coverage-based
BE service
initial TTI
selection
algorithm, the
algorithm for
determining
whether BE
services on the
UE will switch
from HSUPA
channels to R99
channels, the
coverage- and
load- based
102
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
algorithm for
dynamic
configuration of
the channel
mapped to
downlink SRBs
in access mode,
and the
algorithm for
Small Target
Retransmit on
RSCP and
RTWP. Value
50 of this
parameter
indicates that
this parameter is
invalid. In this
case, a UE is not
in a weak
coverage area
even if the RNC
does not receive
the P-CPICH
Ec/N0 value
reported by the
UE or the PCPICH Ec/N0
value reported
by the UE after
the period
specified by the
"EcN0EffectTi
me" parameter
expires.
GUI Value
Range:0~50
Unit:0.5dB
Actual Value
Range:-24.5~0.
5(Actual Value
= (GUI Value 49(offset)) x
0.5)
Default Value:
50
103
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
FakeEcNo
BSC6910
SET UFRC
WRFD-010690
Meaning:Substit
ute of the realtime P-CPICH
Ec/N0 when a
UE establishes a
service or
transits from the
CELL_FACH
or CELL_PCH
state to the
CELL_DCH
state and the
RNC does not
receive the PCPICH Ec/N0
value reported
by the UE or the
P-CPICH Ec/N0
value reported
by the UE after
the period
specified by the
EcN0EffectTim
e parameter
expires. This
parameter is
used for
determining
whether UEs are
under weak
coverage in the
following
algorithms:
coverage-based
BE service
initial TTI
selection
algorithm, the
algorithm for
determining
whether BE
services on the
UE will switch
from HSUPA
channels to R99
channels, the
coverage- and
load- based
104
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
algorithm for
dynamic
configuration of
the channel
mapped to
downlink SRBs
in access mode,
and the
algorithm for
Small Target
Retransmit on
RSCP and
RTWP. Value
50 of this
parameter
indicates that
this parameter is
invalid. In this
case, a UE is not
in a weak
coverage area
even if the RNC
does not receive
the P-CPICH
Ec/N0 value
reported by the
UE or the PCPICH Ec/N0
value reported
by the UE after
the period
specified by the
"EcN0EffectTi
me" parameter
expires.
GUI Value
Range:0~50
Unit:0.5dB
Actual Value
Range:-24.5~0.
5(Actual Value
= (GUI Value 49(offset)) x
0.5)
Default Value:
50
105
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
LittleRetranRabRscpPrd
BSC6900
SET
UCHLQUALIT
YEVALUATE
WRFD-140222
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
Meaning:Interv
al at which UEs
report measured
RSCP values
after RAB
setups when the
RSCP/RTWPbased algorithm
for adaptively
adjusting the
small target
number of
retransmissions
for HSUPA UEs
is activated.
GUI Value
Range:D250,
D500, D1000,
D2000, D3000,
D4000, D6000,
D8000, D12000,
D16000,
D20000,
D24000,
D28000,
D32000,
D64000
Unit:ms
Actual Value
Range:250, 500,
1000, 2000,
3000, 4000,
6000, 8000,
12000, 16000,
20000, 24000,
28000, 32000,
64000
Default
Value:D2000
106
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
LittleRetranRabRscpPrd
BSC6910
SET
UCHLQUALIT
YEVALUATE
WRFD-140222
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
Meaning:Interv
al at which UEs
report measured
RSCP values
after RAB
setups when the
RSCP/RTWPbased algorithm
for adaptively
adjusting the
small target
number of
retransmissions
for HSUPA UEs
is activated.
GUI Value
Range:D250,
D500, D1000,
D2000, D3000,
D4000, D6000,
D8000, D12000,
D16000,
D20000,
D24000,
D28000,
D32000,
D64000
Unit:ms
Actual Value
Range:250, 500,
1000, 2000,
3000, 4000,
6000, 8000,
12000, 16000,
20000, 24000,
28000, 32000,
64000
Default
Value:D2000
107
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
8 Counters
Counters
Counter Name
Counter
Description
NE
Feature ID
Feature Name
73424900
VS.HSUPA.Sm
allRsnAdj.TTI2
ms
Times That
Small Target
Retransmission
Numbers Are
Adjusted for
HSUPA 2 ms
TTI UEs for Cell
BSC6900
WRFD-140222
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
73424901
VS.HSUPA.Sm
allRsnAdj.TTI1
0ms
Times That
Small Target
Retransmission
Numbers Are
Adjusted for
HSUPA 10 ms
TTI UEs for Cell
BSC6900
WRFD-140222
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
73424900
VS.HSUPA.Sm
allRsnAdj.TTI2
ms
Times That
Small Target
Retransmission
Numbers Are
Adjusted for
HSUPA 2 ms
TTI UEs for Cell
BSC6910
WRFD-140222
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
73424901
VS.HSUPA.Sm
allRsnAdj.TTI1
0ms
Times That
Small Target
Retransmission
Numbers Are
Adjusted for
HSUPA 10 ms
TTI UEs for Cell
BSC6910
WRFD-140222
Adaptive
Adjustment of
HSUPA Small
Target
Retransmissions
108
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
9 Glossary
Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
109
WCDMA RAN
Adaptive Adjustment of HSUPA Small Target
Retransmissions Feature Parameter Description
10
10 Reference Documents
Reference Documents
1.
2.
110