Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Metal conditioners
VERYLUBE
Products for engine.
Oil system
Fuel system
Other products
Lubricants
Dear Customer!
Thank you for your interest in products of VERYLUBE
trademark. The VERYLUBE trademark is a property
of XADO Chemical Group. VERYLUBE is a high quality
series of products with a following MOTTO:
The present catalogue will help you to get acquainted with a wide range of VERYLUBE
products and choose exactly what you need for your car.
|3
Anticarbon
Product designed to clean piston rings from carbon.
Fast-acting product designed to clean stuck piston rings of gasoline and diesel engines from carbon. It removes all
scale and tar contaminations from the parts surfaces of cylinder-piston group. It does not require oil change after
application.
Advantages
Restores mobility of stuck piston rings.
Decreases oil consumption.
Cleans cylinders and pistons, combustion chambers,
and valves from all types of contaminations (scale,
carbon, varnish and tar).
Application instructions
1. Warm up the engine. The engine should be warm but
not hot.
2. Unscrew the plugs (burners). Disconnect the wire of
the ignition timing sensor, Hall sensor or commutator.
10ml
10ml
320ml
Art. XB 42051
tube
Art. XB 42151
tube in blister
Art. XB 40011
aerosol can
Note
Avoid getting the substance onto paint.
Safe for catalytic converters, oxygen sensors, mechanical rubber
goods and sealers.
The VERYLUBE ANTICARBON in tubes can be used for engine oil
system flushing:
1. Introduce ANTICARBON into warmed up engine through the oil
filler neck at a ratio 40 ml of ANTICARBON for 35 liters of oil.
2. Let the engine idle for 1015 minutes.
3. Change oil and oil filter.
4|
Advantages
Cleans engine oil system up to potential cleanness
level.
Application instructions
Verylube Absolut+
It is recommended to use Verylube Absolut+ for intensive
cleaning of engine oil system before oil change. It is
especially effective for restoring of the piston rings, which
became stuck due to the short-term engine overheating.
Absolut
Absolut+
250ml
300ml
Art. XB 40159
an
Art. XB 40164
an
Verylube Absolut
It is recommended to use Verylube Absolut with each
oil change or when adding different oil type.
1. Introduce the flush through the oil filler neck in warmed
up engine before oil change.
2. Let the engine idle for 1020 minutes. Do not drive a car!
3. Change oil and oil filter.
Dosage
250 ml (1 can) for 5 L of oil.
|5
Flushing oil
Mineral low-viscosity oil with a complex of special additives for engine and transmission flushing.
Contains revitalizant.
It is designed to clean oil systems of engine and transmission. Special detergent-dispersant, anti-wear and extreme
pressure additives allow safe flushing of oil system (for 3040 minutes) and its efficient cleaning from all types of
contaminations (up to potential purity). D revitalizant creates protective reserve against wear during flushing.
Advantages
Absolutely safe flush of oil system up to the potential
purity (VitaFlush technology).
2L
20L
60L
200L
Art. XB 20250
Art. XB 28750
Art. XB 20450
Art. XB 20550
Application instructions
For engines:
6|
Fuel system
Petroltank
Complex cleaner for fuel system.
Fast-acting product designed to clean the fuel system of gasoline engines. Dissolved carbon, varnish, and dirt are
removed from system with the burnt fuel. Regular use of the cleaner keeps the parts of fuel system perfectly clean and
protects them from corrosion.
Advantages
Quickly cleans the fuel system from varnish and
carbon deposits.
Application instructions
1. Squeeze out the contents of the tube into the petrol tank.
10ml
Art. XB 42052
tube
10ml
Art. XB 42152
tube blister
Expert's Advice
In order to avoid the substance getting on the paint of a
car, squeeze the contents of the tube into the refueling
nozzle before refueling.
Note
Avoid getting the product on the paint.
The cleaner is safe for catalyst converters, oxygen sensors, and general
mechanical rubber goods; when dissolved - for plastic parts.
|7
Aquastop
Water and ice remover from gasoline.
Fast-acting product designed to remove moisture from fuel system. It breaks up water drops and ice crystals, distributing
them evenly throughout the whole volume of fuel. As a result, moisture is removed together with exhaust gases during
the process of fuel combustion. It keeps fuel system parts in ideal condition and protects them from corrosion. It is
recommended for regular use.
Advantages
Quickly and efficiently removes water from the fuel
Application instructions
To remove moisture and ice from fuel system of
gasoline engines.
1. Introduce Verylube Aquastop through the neck of
a fuel tank, at a ratio 10 ml (1 tube) for 5 liters of
gasoline.
10ml
Art. XB 42056
tube
10ml
Art. XB 42156
tube blister
Expert's Advice
For convenient application, squeeze the contents of the
tube into the refueling nozzle before fueling.
Note
To defrost door locks of a car: squeeze a small amount of Verylube
Aquastop into the keyhole. The lock will be defrosted in a minute.
8|
Fuel system
Diesel-Lux
Complex product designed to improve properties of diesel fuel and flush the engine fuel system.
Quickly cleans the fuel system from all types of sediments and contaminations. It protects injector valves from burning
and clogging up with tarry sediments. The Diesel-lux Winter (for winter season) significantly depresses the chilling
temperature of diesel fuel and prevents formation of paraffin crystals.
Advantages
Cleans the fuel system from
Diesel-lux
Summer
Application instructions
Diesel-lux
Winter
10ml
10ml
10ml
10ml
Art. XB 42053
tube
Art. XB 42153
tube blister
Art. XB 42254
tube
Art. XB 42154
tube blister
Dosage
Diesel-lux Summer
Diesel-lux Winter
For 50 liters of fuel.
Note
Compatible with all types of fuel.
Preventive dosage
(with every fueling)
1 tube for 50 l of fuel
Ambient air
temperature,
Repair dosage
(once)
1 tube for 20 l of fuel
0 -20
-20 -30
-30 -40
Tubes,
pcs
Expert's Advice
To make the application easy, squeeze
the contents of the tube into the refueling
nozzle before fueling.
|9
Antigel
Superconcentrate for diesel fuel.
Special super concentrated product designed to improve the low-temperature properties of diesel fuel. It is used to
improve the fluidity and pumpability of fuel at low temperatures.
Advantages
Efficiently decreases the freezing temperature
of diesel fuel.
Application instructions
1. Squeeze the contents of the tube into a fuel tank
(refueling nozzle).
10ml
Art. XB 42254
tube
10ml
Art. XB 42354
tube blister
Expert's Advice
To make the application easy, squeeze the contents
of the tube into the refueling nozzle before fueling.
Dosage
Up to 20 1 tube for 100 liters of diesel fuel.
Up to 35 1 tube for 20 liters of diesel fuel.
Note
VERYLUBE Antigel should be introduced into the non-thickened
(transparent) diesel fuel.
The substance should be warmed up to the temperature of +20...+25
before application.
10 |
Fuel system
Advantages
Cleans carburetor parts (choke, float chamber, jets
320ml
Art. XB 40009
aerosol can
500ml
Art. XB 40109
aerosol can
Application instructions
To clean a carburetor.
1. Take off air filter.
2. Start the engine.
3. Shake the can.
4. Spray liberally onto all visible
carburetor parts. While cleaning
keep up increased engine rpm
with a choker level.
| 11
Advantages
320ml
Art. XB 40038
aerosol can
nominal ones.
Application instructions
To clean a throttle butterfly.
To clean a carburetor.
Quick Start
Product designed for quick engine start.
Efficient product designed for easy and quick starting of engines of all types: gasoline
(carburetor and injector ones), diesel, four- and two-stroke ones, as well as rotary engines.
It is perfect help in winter season.
Advantages
Makes engine starting exceptionally easy at high humidity, wet
spark plugs, weak accumulator and low grade fuel.
320ml
Art. XB 40014
aerosol can
Application instructions
To start a gasoline engine.
12 |
Other products
Advantages
Effectively cleans under
Application instructions
1. Switch off the ignition.
2. Shake the can.
Acts immediately.
parts.
320ml
500ml
Note
Art. XB 40007
aerosol can
Art. XB 40107
aerosol can
Safe for lacquer coating of all types, glass, plastic, rubber and
chrome-plated parts.
Does not contain acid, alkali and other corrosion-hazardous
substances.
Expert's Advice
It is better to clean a cold or slightly warm engine. A high temperature of the engine
provokes fast evaporating of the cleaner and cleaning efficiency can be decreased.
Belt reconditioner
Spray designed to take care of driving belts of engine assemblies.
The product is designed to take care of V-belts and multiple V-belts of the pump drives
of the wheel booster, generator, air conditioner etc. Effectively cleans surfaces from
contaminations and restores elasticity of the belts. Protects from cracking and eliminates
slipping.
Advantages
Cleans the work surface of belts from
contaminations and oiling; removes
slipping.
Application instructions
1. Shake the can.
2. Spray onto the work (V-) surface
of a belt.
320ml
cracking.
Note
Does not require rubbing.
Art. XB 40015
aerosol can
| 13
Advantages
Eliminates the need for expensive repair.
Universal application for gasoline and diesel
engines of cars and other equipment.
Application instructions
1. Shake well before use!
250ml
Art. XB 50010
can
Attention!
The antifreeze in the cooling system is under pressure
when the engine is hot. Be careful when opening the
radiator/cooling system: hot coolant or steam might
escape from the system.
To avoid eventual leaks in the cooling system, use the
sealer right after changing the antifreeze.
Dosage
The can (250 ml) is designed for cooling system capacity up
to 12 L.
14 |
Advantages
Application instructions
thixotropic properties.
500ml
Art. XB 40125
aerosol can
Antigravel
Antigravel rubber coating of light-grey color which allows further painting.
Used for painted surfaces of a car body (lower sections of doors etc.), which are exposed
to road dust and gravel hits. Can be applied to metal, lacquered surfaces and plastics.
Advantages
Forms an elastic film which is
particularly resistant to stone
hitting.
Application instructions
1. Remove dirt, rust and dust from the
surfaces to be covered with Antigravel.
2. Shake the can.
3. Spray onto the surface at a distance of
2030 cm.
4. Apply 23 layers on the surfaces to be
coated. Each next layer should be applied
after short-term waiting.
5. Wait 3060 minutes. Run your car.
Note
The ambient air temperature while treating
should be +1520 .
Excess of Antigravel can be easily removed
with Verylube Tar Stain Remover.
500ml
Art. XB 40126
aerosol can
| 15
Anticor ML
Wax anticorrosion coating for closed car body areas.
High performance rust preventive product designed to protect internal surfaces of hollow parts of a car body: door
hollows, spars, fenders etc. Specially composed for anti-corrosive treatment of a car body based on the Swedish ML
method (spreading, preserving and "sealing up").
Can be applied on metal and lacquer coating surfaces. Spreads well and penetrates into the smallest cavities which
require protection, such as weld seams and cracks.
Advantages
Forms a very thin protective film (from 40 micron) with
strong adhesion.
Removes moisture.
Seals up centers of corrosion attacks.
Has an increased anticorrosion resistance to chemical
activity (weak acids, alkali etc.).
Application instructions
1. Clean the open surfaces of the parts from dirt, rust
and dust.
2. Shake the can.
3. Spray onto the surface at a distance of 2030 cm.
500ml
Art. XB 40129
aerosol can
Note
The ambient air temperature while treating should be +1520 .
Can be used in the engine compartment.
Excess of Anticor ML can be easily removed with Verylube Tar Stain
Remover.
16 |
Advantages
320ml
500ml
Art. XB 40002
aerosol can
Art. XB 40102
aerosol can
Note
Do not use for leather cleaning!
Avoid getting onto non-painted
plastic parts of a car body or
number plates! If occurred, wash
off with water immediately!
Safe for lacquer coating of any
type.
Application instructions
1. Shake the can.
2. Spray onto the surface to be cleaned.
3. Wipe off with a sponge or wash with water after
510 seconds.
Brake cleaner
Effective product for cleaning and degreasing of metal surfaces.
Applied for cleaning the parts of brake system from dirt and grease. Removes dirt with
high pressure. Quickly dries and leaves the surface completely clean. This cleaner
can be also applied for chain cleaning of bicycles and motor machinery. Applied for
degreasing of metal surfaces before application of glue and sealants.
Advantages
Application instructions
Improves braking
blocks
performance
320ml
Art. XB 40037
aerosol can
| 17
Advantages
Quickly cleans discs from hard-to-remove contaminations, caused
by break operation.
500ml
Art. XB 40134
bottle with
trigger
Application instructions
Spray onto the surface of the cold
wheel disc, wash with large amount of
water in 10-15 sec. After cleaning, it is
recommended to treat the cover with
VERYLUBE Conditioner of rubber and
plastic.
Attention!
Please check the effect of the product
on a small part of the disc before
application. Do not apply to units of brake
system, steering system and mounting.
It is not recommended to apply the
product to chromium-plated wheel discs.
In this case use Wheel disc purifier (for
chromium).
Advantages
Quickly cleans discs from hard-to-remove contaminations,
caused by break operation.
Application instructions
Spray onto the surface of the cold wheel disc, wash with large
amount of water in 2-3 min.
500ml
Art. XB 40108
bottle with
trigger
18 |
Advantages
Refreshes and gives deep shine to
Application instructions
1. Shake the can.
2. Spray a small amount of the product
onto the clean dry surface.
3. Polish with a cloth.
320ml
Art. XB 40024
aerosol can
Chrome conditioner
Spray designed to take care of decorative chrome-plated surfaces.
Today's best special product for cleaning and polishing chrome-plated surfaces. Gives a
new appearance to chrome-plated parts of cars, motorcycles and other vehicles.
Advantages
Application instructions
chrome-plated parts.
320ml
Art. XB 40022
aerosol can
| 19
Metal polish
Product designed to take care of exterior metal parts of a car body.
Today's best product for cleaning and polishing metal parts of the car body. It is applied
universally for steel and aluminum load bearing elements, as well as for parts made of
copper alloys and zinc.
Advantages
Application instructions
320ml
Art. XB 40023
aerosol can
Advantages
Cleans micro cracks and
Application instructions
1. Shake the can.
2. Spray a thin layer onto the surface to
be treated.
3. Wipe off with a cloth.
Note
Surfaces do not
require polishing after
treatment.
320ml
Art. XB 40006
aerosol can
500ml
Art. XB 40106
aerosol can
20 |
Dashboard polish
Product designed to take care of plastic and wooden parts of a car compartment.
Efficient product designed to clean and refresh parts in a car compartment (control panel and other plastics, wooden,
leather and vinyl parts). Efficiently cleans the surfaces from contaminations and protects from cracking.
Advantages
Easily penetrates into the smallest scratches on the
surface of parts and removes dirt.
Application instructions
1. Shake the can.
2. Spray a small amount of the product onto the surface
to be cleaned.
3. Wipe off with a cloth.
with scent
cherry
320ml
Art. XB 40020
aerosol can
500ml
Art. XB 40120
aerosol can
with scent
lemon
Expert's Advice
If with time the shine is gone, wipe again the dashboard
with cloth (without the polisher). The shine will appear
again.
320ml
Art. XB 40010
aerosol can
500ml
Art. XB 40110
aerosol can
Note
Does not require lots of polishing.
| 21
Compartment cleaner
Compartment upholstery cleaner.
Effective and handy product designed for cleaning car compartment upholstery (natural
and artificial fabric, carpeting, plastic, etc). Easily cleans oil spots.
Advantages
Application instructions
Removes grime.
Restores original appearance, color
320ml
Note
Art. XB 40013
aerosol can
Leather care
Safe and effective care of leather in a car compartment.
Product designed to take care of natural and artificial leather upholstery (seats, doors,
panels etc). Contains castor oil.
Advantages
Quickly penetrates into
Application instructions
1. Shake the can.
2. Spray a small amount of this product
onto the leather surface.
3. Wipe off with a cloth.
to the finish.
320ml
150ml
glossy
Art. XB 40012
glossy
Art. XB 40112
matt
Art. XB 40032
matt
Art. XB 40132
aerosol can
aerosol can
22 |
Advantages
Cleans the air conditioner
conditioning system,
eliminates musty odors, kills
fungi and bacteria.
320ml
Art. XB 40016
aerosol can
Application instructions
1. Shake the can.
2. Spray the content into a deflector (airway) for cold air
of an air conditioner using tube extender, so that the
substance could get onto evaporator.
3. Start the engine in 1530 minutes and let it idle for 34
minutes with an air conditioner fan turned on.
Note
Spray the substance in a well ventilated area or outside when the
engine is turned off and the car doors are open. Contains biologically
active substances.
Advantages
Application instructions
1. Shake the can.
2. Spray the cleaner for 3-4 seconds into all airways of air
conditioning system (ventilation) of a car.
Deodorizes air.
Note
Spray the substance when the engine is not operating.
Contains biologically active substances.
As preventive measures, use the product not less than once a month.
320ml
Art. XB 40616
aerosol can
Metal conditioner
| 23
Verylube Turbo
Metal conditioner for engine.
A completely synthetic concentrated multicomponent product, composed on the basis of the latest discoveries in tribology
and chemistry. It is formulated specially for internal combustion engines. It is used for complex protection of friction parts
of gasoline and diesel engines, including turbo-charged.
Advantages
Increases engine power.
Increases compression.
Reduces noise and vibration.
Decreases oil consumption.
Improves dynamic characteristics of a vehicle.
Decreases fuel consumption.
Improves motor oil properties.
Protects engine parts from wear.
Makes cold start easy.
Reduces harmful exhausts.
Application instructions
1. Pour the conditioner into warmed up engine through
the oil filler neck.
2. Let the engine idle for 3 minutes.
125ml
Art. XB 40060
can
Technical characteristic
The formula of VERYLUBE TURBO contains carbon
60 molecules (fullerenes) and aliphatic hydrocarbons
reinforced with halogens.
Note
Optimal concentration: 3% of the oil volume. Overdose up to 50% is
allowed, i.e. up to 4.5% of the oil volume.
The conditioner has gentle detergent properties that remove carbon from
piston rings.
To achieve the maximum effect use regularly with every oil change.
24 |
Metal conditioner
Metal conditioner
Multilevel protective formula against wear and overloads of the automobile units.
The product is designed for creation of special conditions for operation of engine units (transmission, hydraulic
system) due to which an effective multilevel system of wear and overload protection will be formed.
The metal conditioners are formulated on the base of a fully synthetic polyhydric polymer and a well-balanced
package of antioxidant and antiscoring additives. The polymer molecules are highly resistant to destructive impact of
local overloads in the friction zone due to covalent interatomic bonds which allow eliminating metal-to-metal contact in
the friction zone within the entire lifespan of the oil.
Advantages
Protects against wear and overloads
Increases engine power and driving
moment
Application
Metal conditioner for engine
1. Pour the product into the oil filler neck of
the warmed up engine at the rate of 3-6%
from the oil system nominal value.
2. Provide the engine operation in idle mode
during 3 minutes.
3. Drive the car in normal mode without any
restrictions. The resource of metal conditioner is enough
for the whole period of oil exploitation.
Nominal dosage
125ml (one bottle) for 4 L of oil.
For
engine
For
transmission
For hydraulic
system
150ml
150ml
150ml
Art. XB 40261
aerosol can
Art. XB 40262
aerosol can
Art. XB 40264
aerosol can
| 25
20ml
Art. XB 40104
packet
Application
instructions
Advantages
320ml
Art. XB 40004
aerosol can
500ml
Art. XB 40404
bottle with
trigger
Note
If strongly
contaminated, the
dosage should be
doubled.
Quickly removes
Concentrate product,
Application instructions
Open the cover. Fill the dozer with the fluid,
squeezing smoothly the main bottle. Pour the fluid
into the windshield washer reservoir (mix it with
water).
Dosage:
25 ml of the fluid for 3 L of water.
Red Penguin
Advantages
250ml
Art. XB 50006
two-chamber
plastic bottle
26 |
Ice-breaker
Frost remover and lock defroster.
It is used to remove frost from the windshields. It also quickly removes ice from
mirrors, paint, chrome-plated, plastic, and rubber parts. Efficiently defrosts door
locks.
Advantages
Quickly defrosts and efficiently
10ml
Art. XB 42263
tube
320ml
Art. XB 40017
aerosol can
Application instructions
VERYLUBE Ice-breaker (aerosol)
To remove ice.
1. Shake the aerosol can.
2. Spray onto the frozen surface, wait
1015 seconds, and remove the
thawed ice with a scraper or a sponge.
To defrost door locks.
1. Shake the aerosol can.
2. Spray into the keyhole. The lock will
be defrosted in 1 minute.
VERYLUBE Ice-breaker (tube)
550ml
Art. XB 40063
bottle with
trigger
Antirain
Spray designed to improve water-resistant properties of windshields surfaces.
Creates a thin hydrophobic film on the glass. After treatment the water drops do not
spread on the glass, but quickly run down improving visibility. Increases significantly the
glass limiting wetting angle.
Advantages
Improves visibility during rain
or sleet.
Prevents freezing of
windshields.
Indispensable if windshield
wipers are out of order.
Application instructions
1. The treatment should be made in dry weather.
2. Shake the can.
3. Spray Antirain onto the clean dry external
surface of the windshield, mirrors and lights.
4. Polish glass with a cloth.
Note
Recommended for regular use (once
per 34 weeks).
320ml
Art. XB 40027
aerosol can
| 27
Antifog
Spray designed to prevent steaming up on windshields.
This efficient product prevents moisture condensation on the internal surfaces of
windshields. Allows avoiding the undesirable effect of window steaming in chilly and
rainy weather.
Advantages
Prevents water condensation on
windshields.
Application instructions
1. Shake the can.
2. Spray Antifog onto the glass surfaces.
3. Wipe the glass with a cloth.
Note
320ml
Art. XB 40028
aerosol can
Auto Shampoo
Concentrate for intensive car cleaning.
Thanks to complex formula of surface-active substances (tensides), it easily and absolutely
safely washes off all kinds of contamination from a car body.
Advantages
Quickly dissolves dirt on the
car body surface.
Application instructions
Open the cover.
Fill the dozer with the shampoo,
squeezing smoothly the bottle.
Add it into water and make foam
Dosage:
25 ml of shampoo for 5 L of water.
250ml
Art. XB 50007
two-chamber
plastic bottle
28 |
Lubricants
Any Way
Universal penetrating spray lubricant for different mechanisms. Contains revitalizant.
It is designed for all types of units and mechanisms, weapons, tools and equipment. AnyWay lubricant restores mobility
of units and parts; it can penetrate easily and quickly into the rusted or jammed joints, lubricates and separates them.
This lubricant efficiently protects contact places from corrosion. It is neutral to rubber, wood, plastics, lacquer coating
and bluing. All-purpose helper!
Advantages
Lubricates assembly parts and restores friction surfaces
using unique XADO technology.
150ml
Art. XB 40001
erosol can
Application instructions
1. Shake the can.
300ml
400ml
Art. XB 40201
erosol can
Art. XB 40101
erosol can
| 29
Any Way
Consistent lubricant with penetrating effect and the revitalizant.
It is designed for all types of units and mechanisms, weapon, tools and equipment, which require long-lasting lubricating
effect. It restores the mobility of units and parts; it can penetrate easily and quickly into the rusted or jammed joints,
lubricates and separates them. Lubricates reliably and protects from corrosion and oxidation.
Advantages
150ml
Art. XB 30001
erosol can
Application instructions
1. Shake the can.
2. Spray the contents onto the clean surface of the
part (joint).
Advantages
Removes oil and grease contaminations from car body
surfaces.
Application instructions
1. Shake the can.
2. Spray a thin layer onto a work surface
(part, joint).
150ml
Art. XB 40203
erosol can
320ml
Art. XB 40003
erosol can
500ml
Art. XB 40103
erosol can
30 |
Lubricants
Advantages
Possesses high mechanical and chemical stability and
keeps protective and anti-wear properties even after
prolonged mechanical and thermal loads.
Application instructions
With pressurized application.
Add the grease through the zerk until desired grease
volume is reached.
Manual application.
Eliminate the previous grease and fill 1/2 of bearing
volume (unit) with Lithium universal grease.
Grease in aerosol can.
5ml
320ml
450ml
125ml
Art. XB 40018
erosol can
Art. XB 30050
grease gun
cartridge
Art. XB 30250
plastic tube
Requirements
NLGI 2 (ASTM D217)
ISO-L-XBCEB 2 (ISO 6743-9)
KP2K-20 (DIN 51502)
Note
Compatible with automotive and industrial lithium greases of all types,
and can be mixed with them in any proportion.
Efficient for assemblies with the rotation speed up to 10,000 rpm.
| 31
Advantages
Provides reliable lubrication of assemblies and
Application instructions
With pressurized application.
Add the grease through the zerk until desired grease
volume is reached.
Manual application.
Eliminate the previous grease and fill 1/2 of bearing
volume (unit) with Lithium complex grease.
450ml
125ml
Art. XB 30052
grease gun
cartridge
Art. XB 30252
plastic tube
Note
Compatible with automotive and industrial lithium greases of all types,
and can be mixed with them in any proportion.
Efficient for assemblies with the rotation speed up to 10,000 rpm.
Requirements
NLGI 2 (ASTM D217)
ISO-L-XBDIB 2 (ISO 6743-9)
KP2N-30 (DIN 51502)
32 |
Lubricants
Advantages
Special grease for constant velocity joints.
Effectively protects assemblies and bearings operating
under peak and/or oscillatory loads.
Application instructions
With pressurized application.
Add the grease through the zerk until desired grease
volume is reached
450ml
125ml
Art. XB 30051
grease gun
cartridge
Art. XB 30251
plastic tube
Manual application.
Eliminate the previous grease and fill 1/2 of bearing
volume (unit) with Lithium grease for CV joints.
Note
Compatible with automotive and industrial lithium greases of all types,
and can be mixed with them in any proportion.
Applied for assemblies with the rotation speed up to 10,000 rpm.
Requirements
NLGI 2 (ASTM D217)
ISO-L-XCEB 2 (ISO 6743-9)
KPF2N-25 (DIN 51502)
| 33
Silicon lubricant
Universal dense silicon spray lubricant.
It lubricates and penetrates into joints made of various materials (metal, plastics, rubber, leather and wood in any
combination). It eliminates creaking of plastic panels, slideblocks and belts. It restores the easiness of lock work. It is
used as a preserving anticorrosion substance for cables, control rods and levers. It possesses perfect water resistant
properties due to the formation of multi-molecular layer of silicon. It prevents plastic and rubber parts from cracking on
the sun.
Advantages
Cleans and restores plastic, vinyl and rubber surfaces.
Gives shine and polishes control panels, restores
their original color and appearance; restores the
appearance of vinyl body upholstery and takes care of
the rubber tire covers.
150ml
320ml
500ml
Art. XB 40205
erosol can
Art. XB 40005
erosol can
Art. XB 40105
erosol can
Application instructions
1. Shake the can.
2. Spray a thin layer onto a work surface (part, joint).
3. If necessary, wipe it with a napkin.
4. 4. In case of severe contaminations, repeat the
treatment.
34 |
Application
instructions
1. Shake the can.
2. Spray a thin layer
onto the clean parts
surface.
Advantages
Makes joint assembling easy.
Makes easy further disassembling of joined parts
320ml
Art. XB 40021
erosol can
Advantages
Provides accurate operation of the
Application instructions
1. Twist out the guide fingers of a brake
caliper.
2. Shake the can.
3. Apply a thing layer of the grease.
4. Assemble the unit.
Note
Use when replacing brake
pads or next maintenance
work.
320ml
Art. XB 40019
erosol can
| 35
Lock lubricant
Penetrating spray lubricant for automobile locks.
Lubricates and ensures easy operation of the lock mechanism.
Removes moisture from the parts surfaces and protects them from corrosion.
Application instructions
50ml
Art. XB 40030
erosol can
Lock de-icer
Aerosol product designed to defrost automobile locks.
Quickly unfreezes the iced parts of the lock mechanism and restores their mobility.
Defrosts ice and removes moisture from the surface of the parts, prevents their further
freezing.
Application instructions
1. Shake the can.
50ml
2. Spray the content (23 sec.) into the keyhole. The lock will thaw in
a minute.
Art. XB 40031
erosol can
Application instructions
1. Shake the can.
2. Spray the content (23 sec.) into
the key-hole.
50ml
320ml
Art. XB 40033
erosol can
Art. XB 40133
erosol can
36 |
Advantages
Quickly displaces soiling from nooks of breech
mechanisms and triggers.
Application instructions
1. Shake the can.
2. Spray onto all parts and mechanisms of the arms.
3. Clean the arms.
75ml
500ml
Art. XA 40003
erosol can
Art. XB 40903
erosol can
500ml
Art. XB 41903
aerosol can with
2-position spray
Note
Does not contain alkali, neutral to plastics, wood, painted and
lacquered surfaces and bluing.
Does not require to be wiped dry.
When preparing the arms for a long-term storage, it is advised to use
VERYLUBE Gun conserving crease.
| 37
Advantages
Helps to prepare the arms for storage quickly.
Possesses high penetrating ability and gets to all parts
of the arms.
Application instructions
1. Shake the can.
2. Spray a thin layer onto the work surface (part, joint).
3. If necessary, wipe with a napkin.
4. If heavily contaminated, repeat the treatment.
75ml
500ml
Art. XA 40004
erosol can
Art. XB 40904
erosol can
500ml
Art. XB 41904
aerosol can with
2-position spray
38 |
Advantages
Quickly (15-30 min) and easily removes soft metal
residues from the inner surface of the barrel bore.
Application instructions
1. Let the gun cool down to the room temperature,
disassemble it for cleaning. Close the barrel breech
(with a rag, false cartridge etc.).
2. Shake the can.
3. Spray the content into the barrel bore till the foam
appears from the muzzle.
500ml
500ml
Art. XB 40906
erosol can
Art. XB 41906
aerosol can with
2-position spray