Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
DataMan 50
Getting
Section
Started
Title
Page 4
2
Page
Page 12
DataMan Software
Page 19
1
4
Page 30
1
5
Page 47
About DataMan 50
DataMan 50 is a compact fixedmount ID reader that among
others offers the following
advanced features:
Smallest high-performance
fixed mount reader
Highest read rates for 1-D and
2-D codes
Reliability and image feedback
DataMan 50 Systems
Omni-directional
1-D Code Reading
DataMan 50L
(DMR-50L-00)
1DMax+ with
HOTBARS
DataMan 50QL
(DMR-50QL-00)
DataMan 50S*
(DMR-50S-00)
Specification
DataMan 50 Imager
Image Sensor
752 x 480
18 s to 25 ms exposure
Image Acquisition
Lens Type
DataMan 50 Accessories
CABLES
1 USB Cable, 1.5 m
(DM100-USB-000)
2 USB Cable, 3 m
(DM100-USB-030)
3 USB & Flying Leads I/O Cable, 2.0 m
(DM-USBIO-00)
4 RS-232 Cable, 1.5 m
(DM100-RS232-000)
5 RS-232 & Flying Leads I/O Cable, 2.5 m
(DM-RS232IO-00)
6 Extension Cable, 5 m
(DM100-EXTCBL-000)
7 RS-232/USB adapter connector
(DM100-PATCH-000)
LENS COVERS
8 ESD-safe Front Cover
(DM50-CLCOV-ESD)
2
4
6
7
CONTROL BOX
12 Control Box (DM-CTRLBOX-00)
DOCUMENTATION AND INSTALLER
13 DataMan 50 Quick Reference Guide
(this document) (590-7165)
14
12
13
14
NOTE: The ESD-safe front cover has to be mounted without the screw washers to
ensure proper electrical connection to the housing.
POWER SUPPLY
9 Power Supply, 6V
(DM100-PWR-000)
MOUNTING BRACKETS
10 Pivot Mounting Bracket
(DM100-PIVOTM-00)
11
10
11
Reader Layout
The following image shows the characteristics of the DataMan 50 reader.
Cable
Mounting holes
(M3 x 3.5mm)
yellow arrow
indicates selected
focus position
3-position
M12 lens
Status LEDs
Internal
illumination
LED aimer
Line up the holes with the icons, and attach the rubber part to the
front window.
Attach both to the housing and add the washers and screws.
Set focus by positioning a coin into the lens cap slit and turning the coin.
Do not use a coin thicker than 2 mm. If no coin is available, use the
edge of the back cover.
PHILLIPS PAN HEAD M1.6 X 8 MM
Make sure that the sealing and the sealing surface are clean before
reassembling the lens cover.
Dimensions
Observe the following DataMan 50 reader dimensions when installing your
reader.
31.75mm
1.25in
27.40 mm
1.08
21.65mm
0.85in
31.75 mm
1.25
23.60mm
21.65 mm
0.93in
0.85
5.67mm
0.22in
45.40mm
1.79in
45.40 mm
1.79
27.40mm
1.08in
23.44mm
0.92in
75
29 0mm
.5
in
5.67 mm
0.22
80 mm (3.15 in)
56 mm (2.2 in)
36 mm (1.4 in)
70 mm 2-D
40
20
1-D
20
1
mm 0
40
20
60
40
80
100
120
140
160
180
200
60
mm
45 mm 2-D
in
in
1-D
mm 0
in
20
60
40
80
100
120
140
160
180
200
110 mm 2-D
1-D
20
mm 0
in
60
40
80
100
120
140
160
180
200
The following table shows the Field of View widths in mm at various distances.
distances in
mm
DM50
45
36
70
56
110
80
Region of
interest
Quick Setup
All main controls and visual feedback in a single view, for
easiest setup and configuration
Connect to Reader
Establish a connection to the reader
Results Display
View results
System Settings
Configure visual and audio feedback, trigger and output
actions
Table View
See all the selectable values in the Setup Tool in one table
Read history
Train
status
Connection status
File Menu
Open Configuration
Save Configuration
Restore Device
Backup Device
Export Parameters
Load Image
Save Image
Train Image
DataMan 50 Triggering
Use the Edit menu for standard Cut, Copy and Paste operations.
Use the View menu to view reader information (serial number, firmware
version, and so on) and to enable and disable various elements of the Setup
Tool, and the Tasks menu to switch between various Setup Tool options.
Use the System menu to manage the current settings on the reader and to
upgrade the features it currently supports:
System Menu
Save Settings
Reset Configuration
Update Firmware
External Triggers
If you are using external triggering you can use any of these methods to
trigger your DataMan 50 series reader:
Training your reader with the expected symbology can make the time
required to decode successive symbols more consistent. In addition,
training may help increase decode yield.
To train your reader, place a code in front of the reader and do one of
the following:
Click and hold the trigger button in
the Setup Tool for a minimum of 3
seconds.
Read Setups
If you want to train the reader to recognize multiple symbologies, you can
present a single image showing all the desired symbologies and perform the
training procedure previously described.
If you cannot present a single image showing all the necessary symbologies,
you can enable incremental training on the Training tab of the Symbology
Settings pane:
With incremental training enabled, you can train the reader using multiple
images showing the symbologies you expect to decode. The reader will train
each new symbology while retaining the existing trained symbologies.
I/O Cable
The I/O cable provides access to trigger and high-speed outputs. Unused wires
can be clipped short or tied back using a tie made of non-conductive material.
You can connect a cable with USB & flying leads to the cable that is
attached to the device. The following table shows the pinout and color
description of the flying leads.
For RS-232, use the Power Supply return path for ground.
PIN
1
Brown
Reserved
Green
TxD
Green/Black
RxD
Red
GND
Brown/White
7
12
Signal
2
6
11
Color
8
13
3
9
14
4
10
15
This is a male
connector/plug.
Blue
RTS
Blue/White
Output-0
White
Input-0
White/Black
Input-1
10
Light Blue
CTS
11
Light Blue/Black
Output-1
12
Light Blue/Yellow
Output-Common
13
Light Blue/Green
Output-Strobe
14
Yellow
Reserved
15
Yellow/Black
Reserved
6
11
1
7
12
2
8
13
3
9
14
4
10
15
This is a female
connector/socket.
PIN
Color
Signal
Black
GND
Blue/White
Output-0
White
Input-0
White/Black
Input-1
11
Light Blue/Black
Output-1
12
Light Blue/Yellow
Output-Common
13
Light Blue/Green
Output-Strobe
You can connect a cable with RS-232 & flying leads to the cable that is attached
to the device. The following table shows the pinout and color description of the
flying leads.
6
11
12
GND
Brown/White
VDC
Blue/White
Output-0
White
Input-0
White/Black
Input-1
11
Light Blue/Black
Output-1
12
Light Blue/Yellow
Output-Common
13
Light Blue/Green
Output-Strobe
10
15
This is a female
connector/socket.
Signal
Black
9
14
Color
8
13
PIN
+Vdd
Input-Internal-1/
Input-Internal-2
(Internal Signals)
Input-0/Input-1
ESD Protection
Constant 2mA
current sink
DM50 sinking
NPN
DM50
OUT
COM
+ -
PNP
DM50
PTC
DSP output
signal
26V or less
Residual voltage
0.8V or less
25mA
Short-circuit current
50mA or less
Short-circuit protection
multifuse - 50mA
Output_IO
50mA
26 VDC or less
Residual voltage
0.85V or less
25mA
Short-circuit current
100mA or less
Short-circuit protection
multifuse - 50mA
PLC
PNP
Output
Common
DM50
50 mA
DM50
50 mA
PLC
Output 0,1
Output 0,1
Output
Common
PLC
PLC
Output Common
DM50
DM50
50 mA
Output 0,1
50 mA
Output 0,1
Output Common
The following figure shows the wiring diagram of the illumination strobe
output.
+5VDC
4.0-5.0V
Low level
0-0.4V
Output current
25mA
Short-circuit current
125mA
Short-circuit protection
multifuse - 50mA
Output-Strobe
0-26V
Low level
0-0.4V
Output current
25mA max
Short-circuit current
125mA
Short-circuit protection
multifuse - 50mA
Strobe
(Internal signal)
ESD Protection
Multi-Port Connections
NPN
LOAD
50 mA
DM50
PNP
DM50
50 mA
LOAD
must provide Tx Data, Rx Data, and ground. The Tx Data and Rx Data pins on
adjacent connectors must be connected to provide the multi-port connection.
You must connect the Setup Tool to each DataMan 50 in turn and enable multi-port operation. Click the Communication Settings task and
check the Enable Multi-Port (RS-232 Sharing) check box.
The following diagram shows how to create a multi-port cable for a 3-reader
system:
DataMan 50
2: Tx Data
3: Rx Data
5: GND
DataMan 50
DataMan 50
PC
2
3
5
2: Rx Data
3: Tx Data
5: GND
DataMan 50 Specifications
Weight
Operating Temperature
Storage Temperature
Maximum Humidity
95% (non-condensing)
Environmental
Vibration
Codes
Discrete I/O
operating limits
Output 2
IMAX @ 24 VDC
mA
VMAX
Source VTYP
Input 0 (Trigger)
Input 1
Power Supply
Requirements
76 g (including cable)
25
26
4
V
V
Sink VIH
VIL
4 - VPSU
02
V
V
VIH
VIL
ITYP
4 26
02
3
V
V
mA
4,5 26 VDC
VPSU
2.5 W maximum
LPS or NEC class 2 power supply
Compliance Statements
DataMan 50 readers meet or exceed the requirements of all applicable standards organizations
for safe operation. However, as with any electrical
equipment, the best way to ensure safe operation is
to operate them according to the agency guidelines
that follow. Please read these guidelines carefully
before using your device.
Regulator
USA
Canada
European
Community
Australia
Japan
Specification
FCC Part 15, Subpart B, Class A
ICES-003, Class A
EN55022:2006 +A1:2007, Class A
EN55024:1998 +A1:2001 +A2:
2003
C-TICK, AS/NZS CISPR 22 / EN
55022 for Class A Equipment
J55022, Class A
Reset Scanner to
Factory Defaults
Reboot Scanner
Copyright 2013 Cognex Corporation All Rights Reserved. This document may not be
copied in whole or in part, nor transferred to any other media or language, without the
written permission of Cognex Corporation. The hardware and portions of the software
described in this document may be covered by one or more of the U.S. patents listed
on the Cognex web site http://www.cognex.com/patents.asp. Other U.S. and foreign
patents are pending. Cognex, the Cognex logo, and DataMan are trademarks, or
registered trademarks, of Cognex Corporation.