Sei sulla pagina 1di 3



6.4.5

Emergency control

When telescoping the tele sections, make sure that the selected, automatically limited telescope lengths
according to the entered ASLI code are complied with.
If the operator notices, on telescoping the tele sections, that these are not extended completely to their
preselected position (malfunction in ASLI system regarding the length change-over point), the rocker tip
switch "emergency control" can be actuated to perform emergency control of the tele sections.


&

'

'

"

"

<

>

<

**)

Optional equipment

12/48

0210_EN_FA035_B2_06_00_00_ab FZ 02
2003-01

Prerequisite: Telescope control appears on the display of the ASLI.


For the ASLI, refer to part G2 Superstructure "Operation of the Automatic
Safe Load Indicator".


1. Activate emergency control:


Actuate the lock handle (1) down to unlock the rocker switch
"telescope emergency mode"; push rocker switch down and lock it.
The green function lamp in the switch is lit.

(1)

After switching on the emergency control, all locking mechanisms change initially over to position "pin
engaged" or "floating".
2.

Check whether the tele cylinder is pin-fastened in one of the tele sections (displays, ASLI, indication of
pin securing mechanism, and valid telescoping indication ID).

In this case, continue as described under item 9.


Otherwise, proceed first of all as described under items 3 to 8.
3. Retract the pin from the tele cylinder; to this effect, move rocker switch
upwards and actuate rocker
tip switch , until complete releasing of the pin lock is signalled.
4. If the position of the tele cylinder with regard to the first telescope to be moved is unclear, retract tele
cylinder completely by moving the left-hand crane control lever back
until the cylinder length 0 is indicated. If the cylinder length transmitter has failed, watch the cable drum
on the boom underside.
5. Extend tele cylinder until one of the ID switches appears in the ASLI display for the tele section to be
reset to its former rig arrangement. To this effect, move left-hand crane control lever forward.
B

"

When the first ID


proximity switch appears, a residual stroke of approx. 10 cm is left. Stop tele cylinder by releasing the
crane control lever immediately.
6. Lock the tele cylinder. To this effect, actuate the rocker switch
to its central position.
7. Subsequently, perform short extension movements via the crane control lever (max. total travel of 20 cm,
or until the first ID proximity switch shuts off). If complete locking is not achieved even after this procedure, retract the tele cylinder. To this effect, actuate the left-hand crane control lever backwards (max.
total travel 20 cm, or until the first ID proximity switch shuts off). If necessary, repeat this procedure.


0210_EN_FA035_B2_06_00_00_ab FZ 02
2003-01

13/48

cont'd.:

8. If complete locking is signalled and the complete telescoping display ID appears, the telescope can be
retracted.
9. Release the telescope. To do so, actuate the left-hand crane control lever forward and extend by approx.
2 cm. If the cylinder length transmitter has failed, watch the cable drum on the boom underside.
10. Unlock the telescope; to this effect, actuate the rocker switch
down and actuate rocker tip switch
until the telescope is completely unlocked.
11. If complete unlocking is not achieved, proceed once more as described as of item 9. If complete
unlocking is not achieved even after several attempts, the telescope must be locked once more. To do
to central position while actuating the left-hand crane control lever several
so, move rocker switch
times briefly to the rear while
. Then, proceed again as described as of
item 9.
12. If the telescope is completely unlocked, it can be retracted; to this end, move left-hand crane control
lever back until the telescope has reached its final position. Reduce engine speed to idle approx. 1 m
before reaching the end position.
13. Lock the telescope; to this effect, move rocker tip switch
to its central position.
upwards and actuate rocker
14. Retract the pin from the tele cylinder; to this effect, move rocker switch
, until complete releasing of the pin lock is signalled. After all telescopes have been
tip switch
retracted, continue as described under as of 15. Otherwise, proceed again as described as of item 5.
15. Retract tele cylinder completely; to this effect, move left-hand crane control lever to the rear until the
cylinder has been retracted.
16. Pin-fasten tele cylinder in a tele section (refer to items 6 and 7).
17. Shut off the engine, switch the ignition off.
upwards.
18. Switch the emergency control off; to do so, actuate the rocker switch
19. Start the engine.
B

Telescoping display IDs


Each tele section is displayed individually in the (ID) display.

Tele section 1

Tele section 2

Tele section 3

Tele section 4

Tele pin locking positions for emergency actuation:

&

14/48

0%
0.00 m
0.30 m
0.60 m
0.90 m

46%
4.50 m
4.79 m
5.11 m
5.39 m

92%
8.99 m
9.27 m
9.60 m
9.88 m

100%
9.77 m
10.05 m
10.39 m
10.66 m

0210_EN_FA035_B2_06_00_00_ab FZ 02
2003-01

Potrebbero piacerti anche