Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Draft A
Date
2014-01-20
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Contents
Contents
1 About This Document..................................................................................................................1
1.1 Scope..............................................................................................................................................................................1
1.2 Intended Audience..........................................................................................................................................................1
1.3 Change History...............................................................................................................................................................2
2 Overview.........................................................................................................................................3
2.1 Introduction....................................................................................................................................................................3
2.2 Benefits...........................................................................................................................................................................3
2.3 Application Networking.................................................................................................................................................4
3 Technical Description...................................................................................................................6
3.1 Introduction....................................................................................................................................................................6
3.2 Transmission Priorities...................................................................................................................................................7
3.3 Traffic Limiting and Shaping.......................................................................................................................................10
3.4 Load Control.................................................................................................................................................................11
3.5 Flow Control.................................................................................................................................................................12
4 Application Scenarios.................................................................................................................15
4.1 Unlimited Access Bandwidth for Multimode Base Stations........................................................................................15
4.1.1 Introduction...............................................................................................................................................................15
4.1.2 Transmission Resource Management Strategies.......................................................................................................16
4.2 Limited Access Bandwidth for Multimode Base Stations............................................................................................20
4.2.1 Introduction...............................................................................................................................................................20
4.2.2 Transmission Resource Management Strategies.......................................................................................................21
4.3 Limited Access Bandwidth for Each Operator in RAN Sharing Scenarios.................................................................29
4.3.1 Introduction...............................................................................................................................................................29
4.3.2 Transmission Resource Management Strategies.......................................................................................................29
5 Related Features...........................................................................................................................34
5.1 Prerequisite Features.....................................................................................................................................................34
5.2 Mutually Exclusive Features........................................................................................................................................34
5.3 Impacted Features.........................................................................................................................................................34
6 Network Impact...........................................................................................................................35
6.1 System Capacity...........................................................................................................................................................35
Issue Draft A (2014-01-20)
ii
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Contents
7 Engineering Guidelines.............................................................................................................36
7.1 When to Use Bandwidth Sharing of Multimode Base Station Co-Transmission.........................................................36
7.2 Required Information...................................................................................................................................................36
7.3 Planning........................................................................................................................................................................36
7.4 Deployment..................................................................................................................................................................37
7.4.1 Requirements.............................................................................................................................................................37
7.4.2 Data Preparation........................................................................................................................................................38
7.4.3 Precautions.................................................................................................................................................................48
7.4.4 Hardware Adjustment................................................................................................................................................48
7.4.5 Initial Configuration (Unlimited Access Bandwidth for GU Dual-Mode Base Stations).........................................48
7.4.6 Initial Configuration (Unlimited Access Bandwidth for GL/GT Dual-Mode Base Stations)...................................51
7.4.7 Initial Configuration (Unlimited Access Bandwidth for UL/UT/ULT Multimode Base Stations)...........................53
7.4.8 Initial Configuration (Unlimited Access Bandwidth for GUL/GUT/GULT Multimode Base Stations)..................55
7.4.9 Initial Configuration (Limited Access Bandwidth for GU Dual-Mode Base Stations).............................................58
7.4.10 Initial Configuration (Limited Access Bandwidth for GL/GT/GLT Multimode Base Stations)............................63
7.4.11 Initial Configuration (Limited Access Bandwidth for UL/UT/ULT Multimode Base Stations)............................66
7.4.12 Initial Configuration (Limited Access Bandwidth for GUL/GUT/GULT Multimode Base Stations)....................70
7.4.13 Initial Configuration (Limited Access Bandwidth for Each Operator in a UL/UT Dual-Mode Base Station in RAN
Sharing Scenarios)..............................................................................................................................................................76
7.4.14 Activation Observation (Unlimited Access Bandwidth for Multimode Base Stations)..........................................84
7.4.15 Activation Observation (Limited Access Bandwidth for Multimode Base Stations)..............................................85
7.4.16 Activation Observation (Limited Access Bandwidth for Each Operator in RAN Sharing Scenarios)...................89
7.5 Performance Monitoring...............................................................................................................................................91
7.6 Parameter Optimization................................................................................................................................................91
7.7 Troubleshooting............................................................................................................................................................91
8 Parameters.....................................................................................................................................92
9 Counters......................................................................................................................................174
10 Glossary.....................................................................................................................................175
11 Reference Documents.............................................................................................................176
iii
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
1.1 Scope
This document describes the Bandwidth Sharing of Multimode Base Station Co-Transmission
feature, including the bandwidth sharing mechanism, recommended transmission configuration
strategies, application scenarios, related features, network impact, and engineering guidelines.
This feature applies to GSM/UMTS, GSM/LTE, UMTS/LTE, and GSM/UMTS/LTE multimode
base stations in co-transmission scenarios.
This document describes the following optional features:
l
In this document, the following naming conventions apply for LTE terms.
Includes FDD and TDD
LTE
LTE FDD
LTE TDD
eNodeB
eRAN
In addition, the "L" and "T" in RAT acronyms refer to LTE FDD and LTE TDD, respectively.
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Feature change
Changes in features of a specific product version
Editorial change
Changes in wording or addition of information that was not described in the earlier version
Draft A (2014-01-20)
Compared with 01 (2013-04-28) of SRAN8.0, Draft A (2014-01-20) of SRAN9.0 includes the
following changes.
Change Type
Change Description
Parameter
Change
Feature change
None.
l Modified the flow control policy for a separateMPT multimode base station where co-transmission
is implemented through backplane interconnection.
Editorial
change
None.
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
2 Overview
Overview
2.1 Introduction
The Bandwidth Sharing of Multimode Base Station Co-Transmission feature centrally manages
GSM, UMTS, and LTE transmission resources. When transmission resources are congested,
this feature ensures the smooth processing of high-priority services and prevents GSM, UMTS,
and LTE services from impacting each other. This ensures high service quality and good user
experience. Bandwidth Sharing of Multimode Base Station Co-Transmission includes the
following transmission resource management strategies: mapping between traffic classes and
transmission priorities, traffic limiting and shaping, load control, and flow control.
If this feature is not enabled, the transmission resources of a multimode base station are managed
in the same way as those of a single-mode base station. For details about transmission resource
management strategies for GSM, UMTS, and LTE, see Transmission Resource Management
Feature Parameter Description for GBSS and RAN, and Transport Resource Management
Feature Parameter Description for eRAN, respectively.
2.2 Benefits
The Bandwidth Sharing of Multimode Base Station Co-Transmission feature provides the
following benefits:
l
GSM, UMTS, and LTE services have different peak hours. Therefore, the transmission resources
of one mode (for example, GSM) can be multiplexed by the other modes (for example, UMTS
and LTE) if GSM is not experiencing a traffic peak. For a multimode base station in cotransmission scenarios, transmission resources can be shared by GSM, UMTS, and LTE. This
promotes resource utilization and ultimately uses fewer transmission resources.
As GSM services continuously shrink, the released GSM bandwidth is gradually occupied by
UMTS and LTE services, which promotes transmission resource utilization.
l
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
2 Overview
When uplink or downlink transmission resources are congested, this feature guarantees the
quality of service (QoS) of high-priority GSM, UMTS, and LTE services without compromising
user experience.
Figure 2-1 shows the networking scheme for a co-MPT GUL triple-mode base station in cotransmission scenarios.
Figure 2-1 Networking scheme for a co-MPT GUL triple-mode base station in co-transmission
scenarios
For details about the networking scheme for a multimode base station in co-transmission
scenarios, see Common Transmission Feature Parameter Description for SingleRAN.
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
2 Overview
NOTE
l In this document, a multimode base station can be a GU/GL/GT/UL/UT/LT dual-mode base station, a
GUL/GLT/ULT/GUT triple-mode base station, or a GULT quadruple-mode base station.
l GBTS or eGBTS refers to the GSM side of a multimode base station. NodeB refers to the UMTS side
of a multimode base station. eNodeB refers to the LTE side of a multimode base station. LTE can be
LTE FDD, LTE TDD, or LTE FDD<E TDD.
l Multimode base stations are classified into co-MPT and separate-MPT multimode base stations, both
introduced in SRAN8.0. In a co-MPT multimode base station, different modes share one main control
board and one O&M channel. In a separate-MPT multimode base station, each mode has its own main
control board and its own O&M channel. The GSM side of a separate-MPT multimode base station
can be either an eGBTS or a GBTS. The GSM side of a co-MPT multimode base station must be an
eGBTS.
l The GBTS is not recommended for providing a co-transmission port to a separate-MPT multimode
base station. This scenario is not covered in this document.
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
Technical Description
3.1 Introduction
For a multimode base station in co-transmission scenarios, the data of the mode that provides a
co-transmission port is called local data. The data of other modes that rely on the co-transmission
port for data transmission is called passing data.
l
For a separate-MPT multimode base station in co-transmission scenarios, the cotransmission port transmits and receives the local data and the passing data. In this case,
the co-transmission port centrally schedules and manages the data of multiple modes.
Definition
GBTS
eGBTS
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
Definition
NodeB
eNodeB
Co-MPT Multimode
Base Station
Separate-MPT
Multimode Base Station
DSCP
DSCP is a field in an IP packet header to indicate the QoS requirements. Each node implements
DiffServ based on the DSCP value.
A multimode base station or base station controller sets the DSCP value for each IP packet based
on the QoS requirements of each service type. From the DSCP value, transmission devices
identify the traffic class and related QoS requirements of the service and perform per-hop
Issue Draft A (2014-01-20)
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
Command
Description
GBTS
SET BTSVLAN
eGBTS and
SET DIFPRI
SET DIFPRI
MOD UDTPARAGRP
NodeB
eNodeB
Pay attention to the following when mapping traffic classes to DSCP values:
l
For separate-MPT multimode base stations in co-transmission scenarios, run the necessary
MML commands to individually map the DSCP values to the data from the O&M plane
and CP for the GBTS, eGBTS, NodeB, and eNodeB. For co-MPT multimode base stations
in co-transmission scenarios, run the SET DIFPRI command once to map the DSCP values
to the data from the O&M plane and CP for the eGBTS, NodeB, and eNodeB.
For multimode base stations in co-transmission scenarios, run the necessary MML
commands to individually map the DSCP values to the data from the UP for the GBTS,
eGBTS, NodeB, and eNodeB.
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
NOTE
The mapping between traffic classes and DSCP values for GSM, UMTS, and LTE services should be
consistent on the base station, the base station controller, and the CN.
VLAN Priority
The VLAN tag defines an IP packet's VLAN priority. Based on the VLAN priority, Layer 2
devices can implement DiffServ.
VLAN priorities of packets with different traffic classes can be determined by DSCP values.
Table 3-3 provides the default mapping between DSCP values and VLAN priorities on the
multimode base station side.
Table 3-3 Default mapping between DSCP values and VLAN priorities
DSCP Value
VLAN Priority
07
815
1623
2431
3239
4047
4855
5663
Queue Priority
Queue priority defines the scheduling priority of a queue. Each Ethernet port or Point-to-Point
Protocol (PPP) link supports eight queues: PQ1, PQ2, PQ3, and WRR (which includes WFQ4
through WFQ8). The queues are displayed in descending order of scheduling priority. A
multimode base station puts packets with different traffic classes into different queues to
implement DiffServ.
NOTE
Queue priorities are determined by the mapping between DSCP values and queue priorities, as
listed in Table 3-4 and Table 3-5. You are not advised to modify the default mapping between
DSCP values and queue priorities.
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
Table 3-4 Default mapping between DSCP values and queue priorities for the GBTS
DSCP Value
Queue
Queue Priority
4063
PQ1
Reserved
PQ2
Reserved
PQ3
3239
WFQ4
2431
WFQ5
1623
WFQ6
815
WFQ7
07
WFQ8
Table 3-5 Default mapping between DSCP values and queue priorities for the eGBTS, NodeB,
and eNodeB in a co-MPT multimode base station
DSCP Value
Queue
Queue Priority
4863
PQ1
4047
PQ2
3239
PQ3
2431
WFQ4
1623
WFQ5
815
WFQ6
07
WFQ7
10
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
NOTE
Base stations cannot dynamically adjust the data rates of real-time services. To prevent real-time service
congestion, at the early stage of network deployment, the bottleneck bandwidth planned for the transmission
devices must be greater than the total bandwidth planned for real-time services in a GU, GL, UL, or GUL
multimode base station.
The traffic limiting and shaping functions can be configured at both the base station level and
the logical port level.
l
11
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
LDR: promotes admission success rates and system capacity by relieving transmission load
and preventing transmission resource congestion.
OLC: alleviates the negative impact of overload on high-priority users by quickly reducing
transmission load.
Load control for each mode in a multimode base station in co-transmission scenarios is the same
as load control in a single-mode base station. GSM and UMTS load is controlled by the related
base station controller and LTE load is controlled by the eNodeB.
For details about load control for GSM, UMTS, and LTE, see Transmission Resource
Management Feature Parameter Description for GBSS and RAN, and Transport Resource
Management Feature Parameter Description for eRAN, respectively.
NE
Support Flow
Control
Remarks
GSM
GBTS/eGBTS and
BSC
No
None
UMTS
Yes
LTE
eNodeB
Yes
The flow control algorithm on a NodeB calculates the transmission delay, the number of
discarded packets, and bandwidth resources available and then performs traffic shaping. In this
way, packet discarding caused by Iub interface congestion is prevented.
This algorithm takes effect only on HSDPA and HSUPA services, and it includes the NodeB
uplink bandwidth adaptive adjustment algorithm and the NodeB HSDPA adaptive flow control
Issue Draft A (2014-01-20)
12
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
algorithm. The NodeB uplink bandwidth adaptive adjustment algorithm is controlled by the
HSUPA congest control switch (TNLCONGCTRLSWITCH) and the traffic control switch
(TCSW) on the NodeB. The NodeB HSDPA adaptive flow control algorithm is controlled by
SWITCH on the NodeB.For working principles and implementation of the NodeB uplink
bandwidth adaptive adjustment algorithm and NodeB HSDPA adaptive flow control algorithm,
see Transmission Resource Management Feature Parameter Description for RAN.
For a co-MPT UL or GUL multimode base station in co-transmission scenarios, if UMTS
HSDPA services are undergoing flow control, the released UMTS bandwidth may be occupied
by LTE services. Consequently, bandwidth available for UMTS services may decrease
considerably. To protect UMTS bandwidth, enable the fair flow control switch
(FAIRSWITCH) on the NodeB side. The fair switch ensures that at least 30% of the actual
receive bandwidth is retained for UMTS HSDPA services. For example, if the total bandwidth
for UMTS HSDPA services decreases to 30% of the actual receive bandwidth, data rates for
UMTS HSDPA services will not be reduced.
The fair flow control switch can be configured either on a physical port of a co-MPT UL dualmode base station or on the corresponding loopback interface (also called logical port) of the
physical port, with the physical port preferred. When configured on the loopback interface, the
fair flow control switch applies only to the following scenarios:
l
Scenario 1: One loopback interface corresponds to one physical port, and UMTS and LTE
services are carried on the same physical port, as shown in Figure 3-1.
Scenario 2: One loopback interface corresponds to multiple physical ports, and UMTS and
LTE services are carried on different physical ports, as shown in Figure 3-2.
Figure 3-1 One loopback interface corresponding to one physical port; UMTS and LTE
services carried on the same physical port
13
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3 Technical Description
Figure 3-2 One loopback interface corresponding to multiple physical ports; UMTS and LTE
services carried on different physical ports
NOTE
The loopback interface is a virtual interface that resides on a router. It is not connected to any other device.
It is recommended that you configure the FAIRSWITCH on the loopback interface in scenario 2 because
this scenario is not a multimode base station co-transmission networking scenario.
For details about the flow control algorithm, see Transmission Resource Management Feature
Parameter Description for WCDMA RAN.
14
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Application Scenarios
The operator cannot or has not planned access bandwidth for each multimode base station.
The bandwidth of the converging device, which converges the data of multimode base
stations, is either limited or unlimited.
For example, in Figure 4-1, the access bandwidth for the three multimode base stations is the
maximum bandwidth 100 Mbit/s and bandwidth for intermediate transmission devices is also
the maximum bandwidth 100 Mbit/s.
Figure 4-1 Unlimited access bandwidth for multimode base stations
15
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Traffic Class
PHB
DSCP Value
VLAN
Priority
GBTS
ESL/OML/RSL
CS6
48
CS Voice
EF
46
CS Data/PS
High PRI
AF41
34
PS Low PRI
AF31
26
IP Clock
EF
46
EML
AF21
18
SCTP
CS6
48
CS Voice
EF
46
CS Data/PS
High PRI
AF41
34
PS Low PRI
AF31
26
OM High
EF
46
OM Low
AF21
18
IP Clock
EF
46
Iub Signal
CS6
48
eGBTS
NodeB
16
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
NE
eNodeB
4 Application Scenarios
Traffic Class
PHB
DSCP Value
VLAN
Priority
CCH&SRB&A
MR
EF
46
Conversational
&Streaming
AF41
34
R99
interactive&bac
kground
AF21
18
HSxPA
interactive&bac
kground
AF11
10
OM High
EF
46
OM Low
AF21
18
IP Clock
EF
46
SCTP
CS6
48
QCI1
EF
46
QCI2
AF41
34
QCI3
AF41
34
QCI4
AF41
34
QCI5
EF
46
QCI6
AF21
18
QCI7
AF21
18
QCI8
AF21
18
QCI9
BE
OM High
EF
46
OM Low
AF21
18
IP Clock
EF
46
In most cases, transmission devices support queue scheduling. Layer 3 and Layer 2 transmission
devices support eight queues. However, if transmission devices in the bearer network support
less than eight queues, transmission priority combining strategies listed in Table 4-2 are
recommended. You can combine packets with different DSCP values into one queue and
combine packets with different VLAN priorities into one queue. For example, if the transmission
devices support six queues, packets whose DSCP values are 48 and 46 can be put into one queue.
17
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Accordingly, packets whose VLAN priorities are 6 and 5 can be put into one queue. This queue
has the highest transmission priority.
Table 4-2 Recommended transmission priority combining strategies if access bandwidth is
unlimited for multimode base stations
Number of Queues
Setting of the
HSUPA
Congestion
Control Switch
Setting of the
HSDPA Adaptive
Flow Control
Algorithm Switch
Setting of the
HSDPA Fair Flow
Control Switch
Separate-MPT GU
dual-mode base
station
ON(On) (default
value)
BW_SHAPING_O
NOFF_TOGGLE
(BW_SHAPING_O
NOFF_TOGGLE)
(default value)
N/A
N/A
N/A
N/A
18
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Setting of the
HSUPA
Congestion
Control Switch
Setting of the
HSDPA Adaptive
Flow Control
Algorithm Switch
Setting of the
HSDPA Fair Flow
Control Switch
Separate-MPT UL
dual-mode base
station
OFF(Off)
l BW_SHAPING
_ONOFF_TOG
GLE
(BW_SHAPING
_ONOFF_TOG
GLE) (default
value): if the
bearer network
supports three or
more queues
N/A
l NO_BW_SHAP
ING
(NO_BW_SHA
PING): if the
bearer network
supports only two
queues
Co-MPT UL dualmode base station
OFF(Off)
l BW_SHAPING
_ONOFF_TOG
GLE
(BW_SHAPING
_ONOFF_TOG
GLE) (default
value): if the
bearer network
supports three or
more queues
ENABLE(Enable)
l NO_BW_SHAP
ING
(NO_BW_SHA
PING): if the
bearer network
supports only two
queues
19
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Setting of the
HSUPA
Congestion
Control Switch
Setting of the
HSDPA Adaptive
Flow Control
Algorithm Switch
Setting of the
HSDPA Fair Flow
Control Switch
Separate-MPT GUL
triple-mode base
station
OFF(Off)
l BW_SHAPING
_ONOFF_TOG
GLE
(BW_SHAPING
_ONOFF_TOG
GLE) (default
value): if the
bearer network
supports three or
more queues
N/A
l NO_BW_SHAP
ING
(NO_BW_SHA
PING): if the
bearer network
supports only two
queues
Co-MPT GUL triplemode base station
OFF(Off)
l BW_SHAPING
_ONOFF_TOG
GLE
(BW_SHAPING
_ONOFF_TOG
GLE) (default
value): if the
bearer network
supports three or
more queues
ENABLE(Enable)
l NO_BW_SHAP
ING
(NO_BW_SHA
PING): if the
bearer network
supports only two
queues
20
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
The maximum data rate for each multimode base station must not exceed the planned
bandwidth.
The access bandwidth for a base station is limited if the bearer network is leased or if the base
station uses satellite, microwave, or xPON to receive data.
For example, in Figure 4-2, the access bandwidth for the three multimode base stations is limited
to 10 Mbit/s.
Figure 4-2 Limited access bandwidth for multimode base stations
Configuring Traffic Limiting and Shaping on the Base Station Controller Side
Set the bandwidth after rate limitation to the access bandwidth planned by the operator for a
multimode base station.
Configuring Traffic Limiting and Shaping on the Co-Transmission Port of the Base
Station Side
Set the bandwidth after rate limitation to the access bandwidth planned by the operator for a
multimode base station.
21
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Traffic Class
PHB
DSCP Value
VLAN
Priority
GBTS
ESL/OML/RSL
CS6
48
CS Voice
EF
46
CS Data/PS
High PRI
AF41
34
PS Low PRI
AF31
26
IP Clock
CS6
46
EML
AF21
18
SCTP
CS6
48
CS Voice
EF
46
CS Data/PS
High PRI
AF41
34
PS Low PRI
AF31
26
OM High
EF
46
OM Low
AF21
18
IP Clock
CS6
46
Iub Signal
CS6
48
CCH&SRB&A
MR
EF
46
Conversational
&Streaming
AF41
34
R99
interactive&bac
kground
AF21
18
HSxPA
interactive&bac
kground
AF11
10
OM High
EF
46
OM Low
AF21
18
eGBTS
NodeB
22
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
NE
eNodeB
4 Application Scenarios
Traffic Class
PHB
DSCP Value
VLAN
Priority
IP Clock
EF
46
SCTP
CS6
48
QCI1
EF
46
QCI2
AF41
34
QCI3
AF41
34
QCI4
AF41
34
QCI5
EF
46
QCI6
AF21
18
QCI7
AF21
18
QCI8
AF21
18
QCI9
BE
OM High
EF
46
OM Low
AF21
18
IP Clock
EF
46
In most cases, transmission devices support queue scheduling. Layer 3 and Layer 2 transmission
devices support eight queues. However, if transmission devices in the bearer network support
less than eight queues, transmission priority combining strategies listed in Table 4-5 are
recommended. You can combine packets with different DSCP values into one queue and
combine packets with different VLAN priorities into one queue. For example, if the transmission
devices support six queues, packets whose DSCP values are 48 and 46 can be put into one queue.
Accordingly, packets whose VLAN priorities are 6 and 5 can be put into one queue. This queue
has the highest transmission priority.
Table 4-5 Recommended transmission priority combining strategies if access bandwidth is
limited for multimode base stations
Number of Queues
23
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Number of Queues
Setting of the
Traffic
Control
Switch
Setting of the
HSUPA
Congestion
Control
Switch
Setting of the
HSDPA
Adaptive
Flow Control
Algorithm
Switch
Setting of the
HSDPA Fair
Flow Control
Switch
Separate-MPT
GU dual-mode
base station
ENABLE
(Enable)
(default value)
ON(On)
(default value)
BW_SHAPING
_ONOFF_TOG
GLE
(BW_SHAPIN
G_ONOFF_TO
GGLE) (default
value)
N/A
ENABLE
(Enable)
(default value)
N/A
N/A
N/A
Co-MPT GU
dual-mode base
station
Separate-MPT
GL dual-mode
base station
Co-MPT GL
dual-mode base
station
24
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Base Station
Type
Setting of the
Traffic
Control
Switch
Setting of the
HSUPA
Congestion
Control
Switch
Setting of the
HSDPA
Adaptive
Flow Control
Algorithm
Switch
Setting of the
HSDPA Fair
Flow Control
Switch
Separate-MPT
UL dual-mode
base station
l ENABLE
(Enable)
(default
value): if cotransmission
is
implemente
d through
backplane
interconnect
ion
OFF(Off)
l BW_SHAP
ING_ONO
FF_TOGG
LE
(BW_SHAP
ING_ONO
FF_TOGG
LE) (default
value): if the
bearer
network
supports
three or
more queues
N/A
l DISABLE
(Disable):if
cotransmission
is
implemente
d through
panel
interconnect
ion
l NO_BW_S
HAPING
(NO_BW_S
HAPING):
if the bearer
network
supports
only two
queues
25
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Base Station
Type
Setting of the
Traffic
Control
Switch
Setting of the
HSUPA
Congestion
Control
Switch
Setting of the
HSDPA
Adaptive
Flow Control
Algorithm
Switch
Setting of the
HSDPA Fair
Flow Control
Switch
Co-MPT UL
dual-mode base
station
ENABLE
(Enable)
(default value)
OFF(Off)
l BW_SHAP
ING_ONO
FF_TOGG
LE
(BW_SHAP
ING_ONO
FF_TOGG
LE) (default
value): if the
bearer
network
supports
three or
more queues
ENABLE
(Enable)
l NO_BW_S
HAPING
(NO_BW_S
HAPING):
if the bearer
network
supports
only two
queues
26
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Base Station
Type
Setting of the
Traffic
Control
Switch
Setting of the
HSUPA
Congestion
Control
Switch
Setting of the
HSDPA
Adaptive
Flow Control
Algorithm
Switch
Setting of the
HSDPA Fair
Flow Control
Switch
Separate-MPT
GUL triplemode base
station
l ENABLE
(Enable)
(default
value): if cotransmission
is
implemente
d through
backplane
interconnect
ion
OFF(Off)
l BW_SHAP
ING_ONO
FF_TOGG
LE
(BW_SHAP
ING_ONO
FF_TOGG
LE) (default
value): if the
bearer
network
supports
three or
more queues
N/A
l DISABLE
(Disable):if
cotransmission
is
implemente
d through
panel
interconnect
ion
l NO_BW_S
HAPING
(NO_BW_S
HAPING):
if the bearer
network
supports
only two
queues
27
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Base Station
Type
Setting of the
Traffic
Control
Switch
Setting of the
HSUPA
Congestion
Control
Switch
Setting of the
HSDPA
Adaptive
Flow Control
Algorithm
Switch
Setting of the
HSDPA Fair
Flow Control
Switch
Co-MPT GUL
triple-mode
base station
ENABLE
(Enable)
(default value)
OFF(Off)
l BW_SHAP
ING_ONO
FF_TOGG
LE
(BW_SHAP
ING_ONO
FF_TOGG
LE) (default
value): if the
bearer
network
supports
three or
more queues
ENABLE
(Enable)
l NO_BW_S
HAPING
(NO_BW_S
HAPING):
if the bearer
network
supports
only two
queues
NOTE
l TCSW is set to ENABLE by default. If you want to set TCSW to DISABLE, first run the ADD
RSCGRP command to add a default transmission resource group to the co-transmission port with
RSCGRPID set to DEFAULTPORT. Then set TCSW to DISABLE for the default transmission
resource group you have added.
l If a separate-MPT multimode base station uses backplane interconnection to implement cotransmission, the tunnel type (TUNNELTYPE) of the main control board that provides the cotransmission port must be set to DL and that of the main control board that does not provide the cotransmission port must be set to UL. If the tunnel type is incorrect, the traffic control function cannot
work properly. For details about tunnel type configuration, see Common Transmission Feature
Parameter Description for SingleRAN.
When co-transmission is applied, the load control algorithm for each mode in a multimode base
station is configured in the same way as the load control algorithm in a single-mode base station.
For details about load control for GSM, UMTS, and LTE, see Transmission Resource
Management Feature Parameter Description for GBSS and RAN, and Transport Resource
Management Feature Parameter Description for eRAN, respectively.
28
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Access bandwidth of one operator is shared among services of each mode run by this
operator.
Access bandwidth for each operator is limited when the bearer network is leased. In RAN15.0,
limited access bandwidth for multiple operators in RAN sharing scenarios applies only to UL
dual-mode base stations. For example, in Figure 4-3, the access bandwidth for each operator is
limited to 10 Mbit/s.
Figure 4-3 Limited access bandwidth for each operator in RAN sharing scenarios
Configuring Traffic Limiting and Shaping on the Base Station Controller Side
Configure a logical port for each operator on the base station controller side. Set the bandwidth
after rate limitation on the logical port to the access bandwidth planned by the operator.
29
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Configuring Traffic Limiting and Shaping on the Co-Transmission Port of the Base
Station Side
Configure a logical port for each operator on the co-transmission port of the base station side.
Set the bandwidth after rate limitation on the logical port to the access bandwidth planned by
the operator.
Traffic Class
PHB
DSCP Value
VLAN
Priority
NodeB
Iub Signal
CS6
48
CCH&SRB&A
MR
EF
46
Conversational
&Streaming
AF41
34
R99
interactive&bac
kground
AF21
18
HSxPA
interactive&bac
kground
AF11
10
OM High
EF
46
OM Low
AF21
18
IP Clock
EF
46
SCTP
CS6
48
QCI1
EF
46
QCI2
AF41
34
QCI3
AF41
34
QCI4
AF41
34
QCI5
EF
46
QCI6
AF21
18
QCI7
AF21
18
QCI8
AF21
18
eNodeB
30
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
NE
4 Application Scenarios
Traffic Class
PHB
DSCP Value
VLAN
Priority
QCI9
BE
OM High
EF
46
OM Low
AF21
18
IP Clock
EF
46
In most cases, transmission devices support queue scheduling. Layer 3 and Layer 2 transmission
devices support eight queues. However, if transmission devices in the bearer network support
less than eight queues, transmission priority combining strategies listed in Table 4-8 are
recommended. You can combine packets with different DSCP values into one queue and
combine packets with different VLAN priorities into one queue. For example, if the transmission
devices support six queues, packets whose DSCP values are 48 and 46 can be put into one queue.
Accordingly, packets whose VLAN priorities are 6 and 5 can be put into one queue. This queue
has the highest transmission priority.
Table 4-8 Recommended transmission priority combining strategies if access bandwidth is
limited for each operator in RAN sharing scenarios
Number of Queues
31
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Table 4-9 Recommended settings for the NodeB flow control algorithm and the HSDPA fair
flow control switch if access bandwidth is limited for each operator in RAN sharing scenarios
Base Station
Type
Setting of the
Traffic
Control
Switch
Setting of the
HSUPA
Congestion
Control
Switch
Setting of the
HSDPA
Adaptive
Flow Control
Algorithm
Switch
Setting of the
HSDPA Fair
Flow Control
Switch
Separate-MPT
UL dual-mode
base station
l ENABLE
(Enable)
(default
value): if cotransmissio
n is
implemente
d through
backplane
interconnect
ion
OFF(Off):
l BW_SHAP
ING_ONO
FF_TOGG
LE
(BW_SHAP
ING_ONO
FF_TOGG
LE) (default
value): if the
bearer
network
supports
three or
more queues
N/A
l DISABLE
(Disable):if
cotransmissio
n is
implemente
d through
panel
interconnect
ion
l NO_BW_S
HAPING
(NO_BW_S
HAPING):
if the bearer
network
supports
only two
queues
32
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
4 Application Scenarios
Base Station
Type
Setting of the
Traffic
Control
Switch
Setting of the
HSUPA
Congestion
Control
Switch
Setting of the
HSDPA
Adaptive
Flow Control
Algorithm
Switch
Setting of the
HSDPA Fair
Flow Control
Switch
Co-MPT UL
dual-mode base
station
ENABLE
(Enable)
(default value)
OFF(Off)
l BW_SHAP
ING_ONO
FF_TOGG
LE
(BW_SHAP
ING_ONO
FF_TOGG
LE) (default
value): if the
bearer
network
supports
three or
more queues
ENABLE
(Enable)
l NO_BW_S
HAPING
(NO_BW_S
HAPING):
if the bearer
network
supports
only two
queues
NOTE
l TCSW is set to ENABLE by default. If you want to set TCSW to DISABLE, first run the ADD
RSCGRP command to add a default transmission resource group to the co-transmission port with
RSCGRPID set to DEFAULTPORT. Then set TCSW to DISABLE for the default transmission
resource group you have added.
l If a separate-MPT multimode base station uses backplane interconnection to implement cotransmission, the tunnel type (TUNNELTYPE) of the main control board that provides the cotransmission port must be set to DL and that of the main control board that does not provide the cotransmission port must be set to UL. If the tunnel type is incorrect, the traffic control function cannot
work properly. For details about tunnel type configuration, see Common Transmission Feature
Parameter Description for SingleRAN.
When co-transmission is applied, the load control algorithm for each mode in a multimode base
station is configured in the same way as the load control algorithm in a single-mode base station.
For details about how to configure the load control algorithm for UMTS and LTE, see
Transmission Resource Management Feature Parameter Description for GBSS and RAN, and
Transport Resource Management Feature Parameter Description for eRAN, respectively.
33
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
5 Related Features
Related Features
34
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
6 Network Impact
Network Impact
Reduced data rates of low-priority services, for example, best effort (BE) services
35
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Engineering Guidelines
7.3 Planning
This section describes planning activities you need to complete before you implement the
feature.
RF Planning
N/A
Network Planning
l
36
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
services and packet switched (PS) services as non-real-time services. Set real-time services
to a higher priority than non-real-time services to ensure the continuity of signaling and CS
services when transmission resources become congested. Activate the flow control
algorithm for each mode to properly allocate transmission resources across non-real-time
services when transmission resources become congested.
l
Hardware Planning
N/A
7.4 Deployment
This section describes how to deploy the Bandwidth Sharing of Multimode Base Station CoTransmission feature.
7.4.1 Requirements
l
Transmission devices
To implement the Bandwidth Sharing of Multimode Base Station Co-Transmission feature,
the bearer network must support QoS management. Otherwise, this feature becomes invalid
when the bearer network is congested. QoS management includes the following aspects:
Layer 3 devices support DSCP-priority-based QoS management.
Layer 2 devices support VLAN-priority-based QoS management.
Transmission devices support the PQ+WRR queue scheduling function, and at least two
PQ queues are supported. (WRR stands for weighted round robin.)
Other features
If the GBTS provides a co-transmission port, the MRFD-211501 IP-Based Multi-mode
Co-Transmission on BS side(GBTS) feature must be activated on the BTS.
If the NodeB provides a co-transmission port, the MRFD-221501 IP-Based Multi-mode
Co-Transmission on BS side(NodeB) feature must be activated on the NodeB.
If the eNodeB provides a co-transmission port, the MRFD-231501 IP-Based Multimode Co-Transmission on BS side(eNodeB) feature must be activated on the eNodeB.
37
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
License
The license for the Bandwidth Sharing of Multimode Base Station Co-Transmission feature
has been activated.
Table 7-1 License control items
Featur
e ID
Feature Name
NE
Sales Unit
MRFD211505
Bandwidth sharing of
MBTS Multi-mode CoTransmission(GBTS)
Bandwidth sharing of
MBTS Multi-mode CoTransmission(GBTS)
BSC
per BTS
MRFD221505
Bandwidth sharing of
MBTS Multi-mode CoTransmission(NodeB)
Bandwidth sharing of
MBTS Multi-mode CoTransmission(NodeB)
NodeB
per NodeB
MRFD231505
Bandwidth sharing of
MBTS Multi-mode CoTransmission
(eNodeB)
Bandwidth sharing of
MBTS Multi-mode CoTransmission(FDD)
eNode
B
per eNodeB
MRFD241505
Bandwidth sharing of
MBTS Multi-mode CoTransmission(LTE
TDD)
Bandwidth sharing of
MBTS Multi-mode CoTransmission(LTE
TDD)
eNode
B
Per eNodeB
Parameter
Name
Parameter
ID
Setting Notes
Data
Source
LR
UL
Committed
Information
Rate
CIR
Network
plan
38
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
MO
7 Engineering Guidelines
Parameter
Name
Parameter
ID
Setting Notes
Data
Source
Committed
Burst Size
CBS
Network
plan
Excessive
Burst Size
EBS
Network
plan
If access bandwidth is limited for each operator in RAN sharing scenarios, data for traffic limiting
and shaping must be prepared on the base station side that provides a co-transmission port. Table
7-3 lists the data to prepare for configuring traffic limiting and shaping.
Table 7-3 Data to prepare for configuring traffic limiting and shaping if access bandwidth is
limited for each operator in RAN sharing scenarios
MO
Parameter Name
Paramete
r ID
Setting Notes
Data Source
RSCGRP
Tx Bandwidth
TXBW
Set this
parameter to the
access
bandwidth
planned by the
operator.
Network plan
TX Committed Burst
Size
TXCBS
l If the
TXBW value
is smaller
than 500
Mbit/s, set
TXCBS to
the TXBW
value
multiplied
by 2 and set
TXEBS to 0
Mbit/s.
Network plan
l If the
TXBW value
is greater
than 500
39
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
MO
7 Engineering Guidelines
Parameter Name
Paramete
r ID
TX Excessive Burst
Size
TXEBS
Setting Notes
Data Source
Mbit/s, set
TXCBS to
1000 Mbit/s
to ensure
that the sum
of TXCBS
and TXEBS
is twice the
TXBW
value.
Network plan
If access bandwidth is unlimited for multimode base stations and limited for each operator in
RAN sharing scenarios, data for traffic limiting and shaping must be prepared on the BSC or
RNC side. Table 7-4 lists the data to prepare for configuring traffic limiting and shaping.
Table 7-4 Data to prepare for configuring traffic limiting and shaping
MO
Parameter
Name
Parameter ID
Setting Notes
Data Source
IPLOGICPORT
LPN
Set this
parameter to the
number of the
BSC/RNC
logical port.
Network plan
40
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
MO
7 Engineering Guidelines
Parameter
Name
Parameter ID
Setting Notes
Data Source
Bandwidth
CIR
Set this
parameter to the
access
bandwidth
planned by the
operator or
bandwidth
calculated by
the traffic
model. When
the access
bandwidth is
limited for each
operator in RAN
sharing
scenarios, set
this parameter to
the access
bandwidth
planned by each
operator.
Network plan
Transport QoS
l
41
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Table 7-5 Data to prepare for configuring the mapping between DSCP values and data from the
O&M plane, CP, and UP of a GBTS
MO
Parameter
Name
Parameter ID
Setting Notes
Data Source
BTSVLAN
Service Type
SERVICETYP
E
Network plan
DSCP
DSCP
See the
recommended
parameter
configurations
in chapter 4
Application
Scenarios.
Table 7-6 Data to prepare for configuring the mapping between DSCP values and data from the
O&M plane and CP of the eGBTS, NodeB, and eNodeB side of a co-MPT multimode base
station
MO
Parameter
Name
Parameter ID
Setting Notes
Data Source
DIFPRI
Priority Rule
PRIRULE
Set this
parameter to the
DSCP value.
Network plan
Signaling
Priority
SIGPRI
OM High
Priority
OMHIGHPRI
OM Low
Priority
OMLOWPRI
See the
recommended
parameter
configurations
in chapter 4
Application
Scenarios.
IP Clock
Priority
IPCLKPRI
42
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Table 7-7 Data to prepare for configuring the mapping between DSCP values and data from the
UP of an eNodeB
MO
Parameter
Name
Parameter ID
Setting Notes
Data Source
UDTPARAGR
P
UDTPARAGR
PID
Set this
parameter to
4048. This
value
corresponds to
the value of the
User Data
Type (19) by
default.
Network plan
Priority
PRI
See the
recommended
parameter
configurations
in chapter 4
Application
Scenarios.
Network plan
Table 7-8 Data to prepare for configuring the mapping between DSCP values and data from the
O&M plane and CP of a BSC
MO
Parameter
Name
Parameter ID
Setting Notes
Data Source
BSCABISPRI
MAP
OML DSCP
OMLDSCP
Network plan
RSL DSCP
RSLDSCP
EML DSCP
EMLDSCP
ESL DSCP
ESLDSCP
See the
recommended
parameter
configurations
in chapter 4
Application
Scenarios.
Network plan
Network plan
Network plan
Table 7-9 Data to prepare for configuring the mapping between DSCP values and data from the
UP of a BSC
MO
Parameter
Name
Parameter ID
Setting Notes
Data Source
TRMMAP
CS voice path
CSVOICEPAT
H
Network plan
CS data path
CSDATAPAT
H
See the
recommended
parameter
configurations
in chapter 4
Network plan
43
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
MO
7 Engineering Guidelines
Parameter
Name
Parameter ID
Setting Notes
Data Source
PS high PRI
data path
PSHPRIDATA
PATH
Application
Scenarios.
Network plan
PSLPRIDATA
PATH
Network plan
Table 7-10 Data to prepare for configuring the mapping between DSCP values and data from
the CP and UP of an RNC
MO
Parameter
Name
Parameter ID
Setting Notes
Data Source
TRMMAP
Common
channel primary
path
CCHPRIPATH
Network plan
IMS SRB
primary path
SIPPRIPATH
SRB primary
path
SRBPRIPATH
See the
recommended
parameter
configurations
in chapter 4
Application
Scenarios.
AMR voice
primary path
VOICEPRIPA
TH
Network plan
R99 CS
conversational
primary path
CSCONVPRIP
ATH
Network plan
R99 CS
streaming
primary path
CSSTRMPRIP
ATH
Network plan
R99 PS
conversational
primary path
PSCONVPRIP
ATH
Network plan
R99 PS
streaming
primary path
PSSTRMPRIP
ATH
Network plan
R99 PS high
PRI interactive
primary path
PSINTHGHPR
IPATH
Network plan
R99 PS middle
PRI interactive
primary path
PSINTMIDPR
IPATH
Network plan
Network plan
Network plan
44
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
MO
7 Engineering Guidelines
Parameter
Name
Parameter ID
Setting Notes
PSINTLOWPR
IPATH
Network plan
R99 PS
background
primary path
PSBKGPRIPA
TH
Network plan
HSDPA Signal
primary path
HDSRBPRIPA
TH
Network plan
HSDPA IMS
Signal primary
path
HDSIPPRIPA
TH
Network plan
HSDPA Voice
primary path
HDVOICEPRI
PATH
Network plan
HSDPA
conversational
primary path
HDCONVPRI
PATH
Network plan
HSDPA
streaming
primary path
HDSTRMPRIP
ATH
Network plan
HSDPA high
PRI interactive
primary path
HDINTHGHP
RIPATH
Network plan
HSDPA middle
PRI interactive
primary path
HDINTMIDPR
IPATH
Network plan
HSDPA low
PRI interactive
primary path
HDINTLOWP
RIPATH
Network plan
HSDPA
background
primary path
HDBKGPRIPA
TH
Network plan
HSUPA Signal
primary path
HUSRBPRIPA
TH
Network plan
HSUPA IMS
Signal primary
path
HUSIPPRIPA
TH
Network plan
HSUPA Voice
primary path
HUVOICEPRI
PATH
Network plan
Data Source
45
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
MO
7 Engineering Guidelines
Parameter
Name
Parameter ID
Setting Notes
Data Source
HSUPA
conversational
primary path
HUCONVPRI
PATH
Network plan
HSUPA
streaming
primary path
HUSTRMPRIP
ATH
Network plan
HSUPA high
PRI interactive
primary path
HUINTHGHP
RIPATH
Network plan
HSUPA middle
PRI interactive
primary path
HUINTMIDPR
IPATH
Network plan
HSUPA low
PRI interactive
primary path
HUINTLOWP
RIPATH
Network plan
HSUPA
background
secondary path
HUBKGPRIPA
TH
Network plan
Flow Control
Table 7-11 lists the data to prepare for setting the flow control algorithm on the NodeB side.
Table 7-11 Data to prepare for setting the flow control algorithm on the NodeB side
MO
Parameter
Name
Parameter ID
Setting
Description
Data Source
RSCGRPALG
Traffic Control
Switch
TCSW
See the
recommended
parameter
configurations
in chapter 4
Application
Scenarios.
Negotiated by
the peer end
ULFLOWCTR
LPARA
Congestion Ctrl
Switch
TNLCONGCT
RLSWITCH
Negotiated by
the peer end
DLFLOWCTR
LPARA
Flow Control
Switch
SWITCH
Fair Switch
FAIRSWITCH
See the
recommended
parameter
configurations
in chapter 4
Application
Scenarios.
46
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Other Data
Table 7-12 lists other data to prepare if access bandwidth is limited for multimode base stations.
Table 7-12 Other data to prepare if access bandwidth is limited for multimode base stations
Data Item
Sample Value
Remarks
20 Mbit/s
10 Mbit/s
BTS index
None
16.16.90.201
None
172.16.140.140
None
16.16.70.201
None
172.16.100.140
None
Table 7-13 lists other data to prepare if access bandwidth is limited for each operator in RAN
sharing scenarios.
Table 7-13 Other data to prepare if access bandwidth is limited for each operator in RAN sharing
scenarios
Data Item
Sample Value
Remarks
10 Mbit/s
10 Mbit/s
16.16.70.201
None
16.16.60.201
None
47
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Data Item
Sample Value
Remarks
16.15.70.201
None
16.15.60.201
None
172.16.90.140
None
172.16.80.140
None
172.15.90.140
None
172.15.80.140
None
7.4.3 Precautions
None
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP and CP on the Iub interface.
2.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP on the Abis interface.
3.
Run the SET BSCABISPRIMAP command to set the mapping between DSCP values and
data from the CP on the Abis interface.
48
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
4.
Run the ADD ADJMAP command to add the mapping from the Iub interface to the
TRMMAP index.
5.
Run the ADD ADJMAP command to add the mapping from the Abis interface to the
TRMMAP index.
Run the SET BTSVLAN command to set the mapping between DSCP values and data
from the CP and UP of the GBTS. Run the SET DIFPRI command to set the mapping
between DSCP values and data from the CP of the eGBTS.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of the NodeB.
Step 3 Configure the dynamic flow control algorithm for the NodeB.
1.
Run the ADD ULFLOWCTRLPARA command to add an HSUPA flow control parameter
to set the uplink bandwidth adaptive flow control switch.
2.
Run the ADD DLFLOWCTRLPARA command to add an HSDPA flow control parameter
to set the HSDPA flow control switch.
----End
//Setting the mapping between DSCP values and data from the UP on the Abis interface
ADD
TRMMAP:TMI=111,ITFT=ABIS,TRANST=IP,CSVOICEPATH=EF,CSDATAPATH=AF41,PSHPRIDATAPATH=A
F41,PSLPRIDATAPATH=AF31;
//Setting the mapping between DSCP values and data from the CP on the Abis interface
SET BSCABISPRIMAP: IDTYPE=BYID, BTSID=1, TRANSTYPE=IP, OMLDSCP=48, RSLDSCP=48,
EMLDSCP=18, ESLDSCP=48;
//Adding the mapping from the Iub interface to the TRMMAP index
ADD ADJMAP: ANI=10, ITFT=IUB, TRANST=IP, CNMNGMODE=SHARE, TMIGLD=110, TMISLV=110,
TMIBRZ=110, FTI=1;
//Adding the mapping from the Abis interface to the TRMMAP index
ADD ADJMAP: ANI=3, ITFT=ABIS, TMIGLD=111, FTI=1;
49
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
SERVICETYPE=OML, DSCP=48;
SERVICETYPE=RSL, DSCP=48;
SERVICETYPE=EML, DSCP=18;
SERVICETYPE=ESL, DSCP=48;
SERVICETYPE= CSVOICE, DSCP=46;
SERVICETYPE= CSDATA, DSCP=34;
SERVICETYPE= PSHIGHPRI, DSCP=34;
SERVICETYPE= PSLOWPRI, DSCP=26;
SERVICETYPE= OTHERDATA, DSCP=46;
//Configuring the uplink bandwidth adaptive flow control switch and HSDPA flow control
switch on the NodeB side
//Adding an HSUPA flow control parameter
ADD ULFLOWCTRLPARA: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
BWPRTSWITCH=ON, TNLCONGCTRLSWITCH=ON;
MO
NE
TRMMAP
BSCABISPRIMAP
BSC
ADJMAP
BTSVLAN/DIFPRI
GBTS or eGBTS
DIFPRI
NodeB
ULFLOWCTRLPA
RA
NodeB
50
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
SN
b
7 Engineering Guidelines
MO
NE
DLFLOWCTRLPA
RA
NodeB
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP on the Abis interface.
2.
Run the SET BSCABISPRIMAP command to set the mapping between DSCP values and
data from the CP on the Abis interface.
3.
Run the ADD ADJMAP command to add the mapping from the Abis interface to the
TRMMAP index.
Run the SET BTSVLAN command to set the mapping between DSCP values and data
from the CP and UP of the GBTS. Run the SET DIFPRI command to set the mapping
between DSCP values and data from the CP of the eGBTS.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of the eNodeB.
3.
Run the MOD UDTPARAGRP command to set the mapping between DSCP values and
data from the UP of the eNodeB.
----End
//Setting the mapping between DSCP values and data from the CP on the Abis interface
SET BSCABISPRIMAP: IDTYPE=BYID, BTSID=1, TRANSTYPE=IP, OMLDSCP=48, RSLDSCP=48,
EMLDSCP=14, ESLDSCP=48;
//Adding the mapping from the Abis interface to the TRMMAP index
Issue Draft A (2014-01-20)
51
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
SERVICETYPE=OML, DSCP=48;
SERVICETYPE=RSL, DSCP=48;
SERVICETYPE=EML, DSCP=18;
SERVICETYPE=ESL, DSCP=48;
SERVICETYPE= CSVOICE, DSCP=46;
SERVICETYPE= CSDATA, DSCP=34;
SERVICETYPE= PSHIGHPRI, DSCP=34;
SERVICETYPE= PSLOWPRI, DSCP=26;
SERVICETYPE= OTHERDATA, DSCP=46;
//Setting the mapping between DSCP values and data from the CP of an eGBTS
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the CP of an eNodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the UP of an eNodeB
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRPID=40,
UDTPARAGRPID=41,
UDTPARAGRPID=42,
UDTPARAGRPID=43,
UDTPARAGRPID=44,
UDTPARAGRPID=45,
UDTPARAGRPID=46,
UDTPARAGRPID=47,
UDTPARAGRPID=48,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRI=46;
PRI=18;
PRI=18;
PRI=18;
PRI=0;
PRI=46,
PRI=26,
PRI=34,
PRI=26,
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
MO
NE
TRMMAP
BSC
BSCABISPRIMAP
BSC
ADJMAP
BSC
BTSVLAN/DIFPRI
GBTS or eGBTS
DIFPRI
eNodeB
UDTPARAGRP
eNodeB
52
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP and CP on the Iub interface.
2.
Run the ADD ADJMAP command to add the mapping from the Iub interface to the
TRMMAP index.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of the NodeB.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of the eNodeB.
3.
Run the MOD UDTPARAGRP command to set the mapping between DSCP values and
data from the UP of the eNodeB.
Step 3 Configure the dynamic flow control algorithm for the NodeB.
1.
Run the ADD ULFLOWCTRLPARA command to add an HSUPA flow control parameter
to set the uplink bandwidth adaptive flow control switch.
2.
Run the ADD DLFLOWCTRLPARA command to add an HSDPA flow control parameter
to set the HSDPA flow control switch.
----End
//Adding the mapping from the Iub interface to the TRMMAP index
ADD ADJMAP: ANI=10, ITFT=IUB, TRANST=IP, CNMNGMODE=SHARE, TMIGLD=110, TMISLV=110,
TMIBRZ=110, FTI=1;
53
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Setting the mapping between DSCP values and data from the CP of the eNodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the UP of the eNodeB
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRPID=40,
UDTPARAGRPID=41,
UDTPARAGRPID=42,
UDTPARAGRPID=43,
UDTPARAGRPID=44,
UDTPARAGRPID=45,
UDTPARAGRPID=46,
UDTPARAGRPID=47,
UDTPARAGRPID=48,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRI=46;
PRI=18;
PRI=18;
PRI=18;
PRI=0;
PRI=46,
PRI=26,
PRI=34,
PRI=26,
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
//Adding an HSDPA flow control parameter in the case of a separate-MPT multimode base
station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING;
//Adding an HSDPA flow control parameter in the case of a co-MPT multimode base station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING, FAIRSWTICH=ENABLE;
54
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Set parameters on the CME configuration interface according to the operation sequence
described in Table 7-16. For instructions on how to perform the CME single configuration, see
CME Single Configuration Operation Guide.
Table 7-16 MOs related to this feature
SN
1
MO
NE
TRMMAP
RNC
ADJMAP
RNC
DIFPRI
NodeB
DIFPRI
eNodeB
UDTPARAGRP
eNodeB
ULFLOWCTRLPA
RA
NodeB
DLFLOWCTRLPA
RA
NodeB
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP and CP on the Iub interface.
2.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP on the Abis interface.
3.
Run the SET BSCABISPRIMAP command to set the mapping between DSCP values and
data from the CP on the Abis interface.
4.
Run the ADD ADJMAP command to add the mapping from the Iub interface to the
TRMMAP index.
5.
Run the ADD ADJMAP command to add the mapping from the Abis interface to the
TRMMAP index.
Run the SET BTSVLAN command to set the mapping between DSCP values and data
from the CP and UP of a GBTS. Run the SET DIFPRI command to set the mapping
between DSCP values and data from the CP of an eGBTS.
55
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of a NodeB.
3.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of an eNodeB.
4.
Run the MOD UDTPARAGRP command to set the mapping between DSCP values and
data from the UP of an eNodeB.
Step 3 Configure the dynamic flow control algorithm for the NodeB.
1.
Run the ADD ULFLOWCTRLPARA command to add an HSUPA flow control parameter
to set the uplink bandwidth adaptive flow control switch.
2.
Run the ADD DLFLOWCTRLPARA command to add an HSDPA flow control parameter
to set the HSDPA flow control switch.
----End
//Setting the mapping between DSCP values and data from the UP on the Abis interface
ADD
TRMMAP:TMI=111,ITFT=ABIS,TRANST=IP,CSVOICEPATH=EF,CSDATAPATH=AF41,PSHPRIDATAPATH=A
F41,PSLPRIDATAPATH=AF31;
//Setting the mapping between DSCP values and data from the CP on the Abis interface
SET BSCABISPRIMAP: IDTYPE=BYID, BTSID=1, TRANSTYPE=IP, OMLDSCP=48, RSLDSCP=48,
EMLDSCP=18, ESLDSCP=48;
//Adding the mapping from the Iub interface to the TRMMAP index
ADD ADJMAP: ANI=10, ITFT=IUB, TRANST=IP, CNMNGMODE=SHARE, TMIGLD=110, TMISLV=110,
TMIBRZ=110, FTI=1;
//Adding the mapping from the Abis interface to the TRMMAP index
ADD ADJMAP: ANI=3, ITFT=ABIS, TMIGLD=111, FTI=1;
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
SERVICETYPE=OML, DSCP=48;
SERVICETYPE=RSL, DSCP=48;
SERVICETYPE=EML, DSCP=18;
SERVICETYPE=ESL, DSCP=48;
SERVICETYPE= CSVOICE, DSCP=46;
SERVICETYPE= CSDATA, DSCP=34;
SERVICETYPE= PSHIGHPRI, DSCP=34;
56
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Setting the mapping between DSCP values and data from the CP of an eGBTS
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the CP of a NodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the CP of an eNodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the UP of an eNodeB
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRPID=40,
UDTPARAGRPID=41,
UDTPARAGRPID=42,
UDTPARAGRPID=43,
UDTPARAGRPID=44,
UDTPARAGRPID=45,
UDTPARAGRPID=46,
UDTPARAGRPID=47,
UDTPARAGRPID=48,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRI=46;
PRI=18;
PRI=18;
PRI=18;
PRI=0;
PRI=46,
PRI=26,
PRI=34,
PRI=26,
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
//Adding an HSDPA flow control parameter in the case of a separate-MPT multimode base
station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING;
//Adding an HSDPA flow control parameter in the case of a co-MPT multimode base station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING, FAIRSWTICH=ENABLE;
57
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
MO
NE
TRMMAP
BSC
TRMMAP
RNC
BSCABISPRIMAP
BSC
ADJMAP
BSC
ADJMAP
RNC
BTSVLAN/DIFPRI
GBTS or eGBTS
DIFPRI
NodeB
DIFPRI
eNodeB
UDTPARAGRP
eNodeB
ULFLOWCTRLPA
RA
NodeB
DLFLOWCTRLPA
RA
NodeB
Run the ADD IPLOGICPORT command to add an IP logical port on the Abis interface.
2.
Run the ADD IPLOGICPORT command to add an IP logical port on the Iub interface.
58
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3.
7 Engineering Guidelines
4.
l If the transmission resource pool feature is not implemented on the Iub interface, you can
run the ADD IPPATH command to bind an IP path and an IP logical port.
l If the transmission resource pool feature is implemented on the Iub interface, you can run
the ADD ADJLOGICPORTBIND command to bind an adjacent node and an IP logical
port.
Step 3 Configure a TRM table on the base station controller side.
Configure a TRM table for the RNC and BSC, respectively. For details, see section 4.2.2
Transmission Resource Management Strategies.
1.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP and CP on the Iub interface.
2.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP on the Abis interface.
3.
Run the SET BSCABISPRIMAP command to set the mapping between DSCP values and
data from the CP on the Abis interface.
4.
Run the ADD ADJMAP command to add the mapping from the Iub interface to the
TRMMAP index.
5.
Run the ADD ADJMAP command to add the mapping from the Abis interface to the
TRMMAP index.
Run the SET BTSVLAN command to set the mapping between DSCP values and data
from the CP and UP of a GBTS. Run the SET DIFPRI command to set the mapping
between DSCP values and data from the CP of an eGBTS.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of a NodeB.
Step 5 Configure the dynamic flow control algorithm for the NodeB.
1.
Run the ADD ULFLOWCTRLPARA command to add an HSUPA flow control parameter
to set the uplink bandwidth adaptive flow control switch.
2.
Run the ADD DLFLOWCTRLPARA command to add an HSDPA flow control parameter
to set the HSDPA flow control switch.
----End
Issue Draft A (2014-01-20)
59
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Configuring traffic limiting and shaping if the NodeB side of a separate-MPT multimode base
station provides a co-transmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//Configuring traffic limiting and shaping if a co-MPT multimode base station provides a cotransmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//In the preceding script, the unit of bandwidth configured on a logical port is 64 kbit/s. Therefore,
the CIR value 157 means that the configured bandwidth is 10,048 kbit/s.
//Adding a logical port on the Abis interface (BSC6910)
ADD IPLOGICPORT: SRN=1, SN=24, BT=GOUc, LPNTYPE=Leaf, FLOWCTRLSWITCH=ON, CIR=157,
LPN=1, CARRYT=IPPOOL, IPADDR="172.16.140.140";//In the preceding script, the unit
of bandwidth configured on a logical port is 64 kbit/s. Therefore, the CIR value
157 means that the configured bandwidth is 10,048 kbit/s.
//In the preceding script, the unit of bandwidth configured on a logical port is 64 kbit/s. Therefore,
the CIR value 313 means that the configured bandwidth is 20,032 kbit/s.
//For a GBTS, binding an IP logical port and a GBTS on the Abis interface
SET BTSIP: IDTYPE=BYID, BTSID=1, BTSCOMTYPE=LOGICIP, BTSIP="16.16.90.201",
BSCIP="172.16.140.140", CFGFLAG=IPLGCPORT, SN=24, LPN=1;
//In the preceding script, the base station is identified by its base station index.
//For an eGBTS, binding an IP path and an IP logical port on the Abis interface if the peer end
is a BSC6900
ADD IPPATH: ANI=3, PATHID=0, ITFT=ABIS, ISLOGICALBTS=No, PATHT=QoS, TXBW=10000,
RXBW=10000, VLANFlAG=DISABLE, PATHCHK=DISABLED, AbisLnkBKFLAG=OFF;
//For an eGBTS, binding an adjacent node and an IP logical port on the Abis interface if the peer
end is a BSC6910
ADD ADJLOGICPORTBIND: ANI=3, SRN=1, SN=24, LPN=1;
60
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Binding an IP path and an IP logical port if the transmission resource pool feature is not
implemented on the Iub interface
ADD IPPATH: ANI=10, PATHID=1, ITFT=IUB, TRANST=IP, PATHT=QoS,
IPADDR="172.16.100.140", PEERIPADDR="16.16.70.201", TXBW=20000, RXBW=20000,
CARRYFLAG=NULL, VLANFlAG=DISABLE, PATHCHK=DISABLED;
//Binding an adjacent node and an IP logical port if the transmission resource pool feature is
implemented on the Iub interface
ADD ADJLOGICPORTBIND: ANI=10, SRN=1, SN=26, LPN=1;
//Setting the mapping between DSCP values and data from the UP on the Abis interface
ADD
TRMMAP:TMI=111,ITFT=ABIS,TRANST=IP,CSVOICEPATH=EF,CSDATAPATH=AF41,PSHPRIDATAPATH=A
F41,PSLPRIDATAPATH=AF31;
//Setting the mapping between DSCP values and data from the CP on the Abis interface
SET BSCABISPRIMAP: IDTYPE=BYID, BTSID=1, TRANSTYPE=IP, OMLDSCP=48, RSLDSCP=48,
EMLDSCP=18, ESLDSCP=48;
//Adding the mapping from the Iub interface to the TRMMAP index
ADD ADJMAP: ANI=10, ITFT=IUB, TRANST=IP, CNMNGMODE=SHARE, TMIGLD=110, TMISLV=110,
TMIBRZ=110, FTI=1;
//Adding the mapping from the Abis interface to the TRMMAP index
ADD ADJMAP: ANI=3, ITFT=ABIS, TMIGLD=111, FTI=1;
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
SERVICETYPE=OML, DSCP=48;
SERVICETYPE=RSL, DSCP=48;
SERVICETYPE=EML, DSCP=18;
SERVICETYPE=ESL, DSCP=48;
SERVICETYPE= CSVOICE, DSCP=46;
SERVICETYPE= CSDATA, DSCP=34;
SERVICETYPE= PSHIGHPRI, DSCP=34;
SERVICETYPE= PSLOWPRI, DSCP=26;
SERVICETYPE= OTHERDATA, DSCP=46;
61
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Configuring the uplink bandwidth adaptive flow control switch and HSDPA flow control
switch on the NodeB side
//Adding an HSUPA flow control parameter
ADD ULFLOWCTRLPARA: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
BWPRTSWITCH=ON, TNLCONGCTRLSWITCH=ON;
MO
NE
LR/LR/LR
eGBTS, NodeB, or
co-MPT multimode
base stations
IPLOGICPORT
BTSIP/IPPATH/
ADJLOGICPORTB
IND
BSC
IPPATH/
ADJLOGICPORTB
IND
RNC
TRMMAP
BSCABISPRIMAP
BSC
ADJMAP
BTSVLAN/DIFPRI
GBTS or eGBTS
DIFPRI
NodeB
ULFLOWCTRLPA
RA
NodeB
DLFLOWCTRLPA
RA
NodeB
62
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Run the ADD IPLOGICPORT command to add an IP logical port on the Abis interface.
2.
l For a GBTS, you can run the SET BTSIP command to bind an IP logical port and a GBTS.
l For an eGBTS, you can run the ADD IPPATH command to bind an IP path and an IP logical
port if the peer end is a BSC6900.
l For an eGBTS, you can run the ADD ADJLOGICPORTBIND command to bind an
adjacent node and an IP logical port if the peer end is a BSC6910.
Step 3 Configure a TRM table on the base station controller side.
Configure a TRM table for the BSC. For details, see section 4.2.2 Transmission Resource
Management Strategies.
1.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP on the Abis interface.
2.
Run the SET BSCABISPRIMAP command to set the mapping between DSCP values and
data from the CP on the Abis interface.
3.
Run the ADD ADJMAP command to add the mapping from the Abis interface to the
TRMMAP index.
Run the SET BTSVLAN command to set the mapping between DSCP values and data
from the CP and UP of a GBTS. Run the SET DIFPRI command to set the mapping
between DSCP values and data from the CP of an eGBTS.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of an eNodeB.
3.
Run the MOD UDTPARAGRP command to set the mapping between DSCP values and
data from the UP of an eNodeB.
----End
63
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Configuring traffic limiting and shaping if the eGBTS side of a separate-MPT multimode base
station provides a co-transmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//Configuring traffic limiting and shaping if the eNodeB side of a separate-MPT multimode base
station provides a co-transmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//Configuring traffic limiting and shaping if a co-MPT multimode base station provides a cotransmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//For a GBTS, binding an IP logical port and a GBTS on the Abis interface
SET BTSIP: IDTYPE=BYID, BTSID=1, BTSCOMTYPE=LOGICIP, BTSIP="16.16.90.201",
BSCIP="172.16.140.140", CFGFLAG=IPLGCPORT, SN=24, LPN=1;//In the preceding script,
the base station is identified by its base station index.
//For an eGBTS, binding an IP path and an IP logical port on the Abis interface if the peer end
is a BSC6900
ADD IPPATH: ANI=3, PATHID=0, ITFT=ABIS, ISLOGICALBTS=No, PATHT=QoS, TXBW=10000,
RXBW=10000, VLANFlAG=DISABLE, PATHCHK=DISABLED, AbisLnkBKFLAG=OFF;
//For an eGBTS, binding an adjacent node and an IP logical port on the Abis interface if the peer
end is a BSC6910
ADD ADJLOGICPORTBIND: ANI=3, SRN=1, SN=24, LPN=1;
//Setting the mapping between DSCP values and data from the CP on the Abis interface
SET BSCABISPRIMAP: IDTYPE=BYID, BTSID=1, TRANSTYPE=IP, OMLDSCP=48, RSLDSCP=48,
EMLDSCP=18, ESLDSCP=48;
//Adding the mapping from the Abis interface to the TRMMAP index
Issue Draft A (2014-01-20)
64
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
SERVICETYPE=OML, DSCP=48;
SERVICETYPE=RSL, DSCP=48;
SERVICETYPE=EML, DSCP=18;
SERVICETYPE=ESL, DSCP=48;
SERVICETYPE= CSVOICE, DSCP=46;
SERVICETYPE= CSDATA, DSCP=34;
SERVICETYPE= PSHIGHPRI, DSCP=34;
SERVICETYPE= PSLOWPRI, DSCP=26;
SERVICETYPE= OTHERDATA, DSCP=46;
//Setting the mapping between DSCP values and data from the CP of an eGBTS
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the CP of an eNodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the UP of an eNodeB
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRPID=40,
UDTPARAGRPID=41,
UDTPARAGRPID=42,
UDTPARAGRPID=43,
UDTPARAGRPID=44,
UDTPARAGRPID=45,
UDTPARAGRPID=46,
UDTPARAGRPID=47,
UDTPARAGRPID=48,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRI=46;
PRI=18;
PRI=18;
PRI=18;
PRI=0;
PRI=46,
PRI=26,
PRI=34,
PRI=26,
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
MO
NE
LR/LR/LR
eGBTS, eNodeB, or
co-MPT multimode
base stations
IPLOGICPORT
BSC
BTSIP/IPPATH/
ADJLOGICPORTB
IND
BSC
TRMMAP
BSC
3
Issue Draft A (2014-01-20)
65
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
SN
7 Engineering Guidelines
MO
NE
BSCABISPRIMAP
BSC
ADJMAP
BSC
BTSVLAN/DIFPRI
GBTS or eGBTS
DIFPRI
eNodeB
UDTPARAGRP
eNodeB
Run the ADD IPLOGICPORT command to add an IP logical port on the Iub interface.
2.
l If the transmission resource pool feature is not implemented on the Iub interface, you can
run the ADD IPPATH command to bind an IP path and an IP logical port on the Iub interface.
l If the transmission resource pool feature is implemented on the Iub interface, you can run
the ADD ADJLOGICPORTBIND command to bind an adjacent node and an IP logical
port on the Iub interface.
Step 3 Configure a TRM table on the base station controller side.
Configure a TRM table for the RNC. For details, see section 4.2.2 Transmission Resource
Management Strategies.
1.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP and CP on the Iub interface.
2.
Run the ADD ADJMAP command to add the mapping from the Iub interface to the
TRMMAP index.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of a NodeB.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of an eNodeB.
66
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
3.
7 Engineering Guidelines
Run the MOD UDTPARAGRP command to set the mapping between DSCP values and
data from the UP of an eNodeB.
Step 5 Configure the dynamic flow control algorithm for the NodeB.
1.
Run the ADD ULFLOWCTRLPARA command to add an HSUPA flow control parameter
to set the uplink bandwidth adaptive flow control switch.
2.
Run the ADD DLFLOWCTRLPARA command to add an HSDPA flow control parameter
to set the HSDPA flow control switch.
Step 6 Disable the traffic control switch of the default transport resource group configured on the cotransmission port.
If the NodeB or eNodeB side of a separate-MPT multimode base station provides a cotransmission port and co-transmission is implemented through panel interconnection, the traffic
control switch for a transport resource group must be disabled on the co-transmission port.
Otherwise, when transmission resources become congested, passing data will preempt
bandwidth from the local data. This deteriorates user experience.
1.
Run the ADD RSCGRP command to configure a default transport resource group on the
co-transmission port.
2.
Run the SET RSCGRPALG command to disable the traffic control switch of the default
transport resource group you have configured.
----End
//Configuring traffic limiting and shaping if the eNodeB side of a separate-MPT multimode base
station provides a co-transmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//Configuring traffic limiting and shaping if a co-MPT multimode base station provides a cotransmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//Binding an IP path and an IP logical port if the transmission resource pool feature is not
implemented on the Iub interface
Issue Draft A (2014-01-20)
67
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Binding an adjacent node and an IP logical port if the transmission resource pool feature is
implemented on the Iub interface
ADD ADJLOGICPORTBIND: ANI=10, SRN=1, SN=26, LPN=1;
//Adding the mapping from the Iub interface to the TRMMAP index
ADD ADJMAP: ANI=10, ITFT=IUB, TRANST=IP, CNMNGMODE=SHARE, TMIGLD=110, TMISLV=110,
TMIBRZ=110, FTI=1;
//Setting the mapping between DSCP values and data from the CP of an eNodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the UP of an eNodeB
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRPID=40,
UDTPARAGRPID=41,
UDTPARAGRPID=42,
UDTPARAGRPID=43,
UDTPARAGRPID=44,
UDTPARAGRPID=45,
UDTPARAGRPID=46,
UDTPARAGRPID=47,
UDTPARAGRPID=48,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRI=46;
PRI=18;
PRI=18;
PRI=18;
PRI=0;
PRI=46,
PRI=26,
PRI=34,
PRI=26,
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
68
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Adding an HSDPA flow control parameter in the case of a separate-MPT multimode base
station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING;
//Adding an HSDPA flow control parameter in the case of a co-MPT multimode base station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING, FAIRSWTICH=ENABLE;
//Disabling the traffic control switch of the default transport resource group configured on the
co-transmission port
//Configuring a default transport resource group on the co-transmission port in a separate-MPT
multimode base station where co-transmission is implemented through panel interconnection
ADD RSCGRP: SN=6, BEAR=IP, SBT=BASE_BOARD, PT=ETH, RSCGRPID=DEFAULTPORT, RU=KBPS;
//Disabling the traffic control switch on the default transport resource group you have configured
SET RSCGRPALG: SN=6, BEAR=IP, SBT=BASE_BOARD, PT=ETH, RSCGRPID=DEFAULTPORT,
TCSW=DISABLE;
MO
NE
LR/LR/LR
NodeB, eNodeB, or
co-MPT multimode
base stations
IPLOGICPORT
RNC
IPPATH/
ADJLOGICPORTB
IND
RNC
69
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
SN
3
7 Engineering Guidelines
MO
NE
TRMMAP
RNC
ADJMAP
RNC
DIFPRI
NodeB
DIFPRI
eNodeB
UDTPARAGRP
eNodeB
ULFLOWCTRLPA
RA
NodeB
DLFLOWCTRLPA
RA
NodeB
RSCGRP
NodeB, eNodeB, or
multimode base
stations
RSCGRPALG
NodeB, eNodeB, or
multimode base
stations
Run the ADD IPLOGICPORT command to add an IP logical port on the Abis interface.
2.
Run the ADD IPLOGICPORT command to add an IP logical port on the Iub interface.
3.
4.
70
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
l If the transmission resource pool feature is not implemented on the Iub interface, you can
run the ADD IPPATH command to bind an IP path and an IP logical port.
l If the transmission resource pool feature is implemented on the Iub interface, you can run
the ADD ADJLOGICPORTBIND command to bind an adjacent node and an IP logical
port.
Step 3 Configure a TRM table on the base station controller side.
Configure a TRM table for the RNC and BSC, respectively. For details, see 4.2.2 Transmission
Resource Management Strategies.
1.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP and CP on the Iub interface.
2.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP on the Abis interface.
3.
Run the SET BSCABISPRIMAP command to set the mapping between DSCP values and
data from the CP on the Abis interface.
4.
Run the ADD ADJMAP command to add the mapping from the Iub interface to the
TRMMAP index.
5.
Run the ADD ADJMAP command to add the mapping from the Abis interface to the
TRMMAP index.
Run the SET BTSVLAN command to set the mapping between DSCP values and data
from the CP and UP of a GBTS. Run the SET DIFPRI command to set the mapping
between DSCP values and data from the CP of an eGBTS.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of a NodeB.
3.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of an eNodeB.
4.
Run the MOD UDTPARAGRP command to set the mapping between DSCP values and
data from the UP of an eNodeB.
Step 5 Configure the dynamic flow control algorithm for the NodeB.
1.
Run the ADD ULFLOWCTRLPARA command to add an HSUPA flow control parameter
to set the uplink bandwidth adaptive flow control switch.
2.
Run the ADD DLFLOWCTRLPARA command to add an HSDPA flow control parameter
to set the HSDPA flow control switch.
Step 6 Disable the traffic control switch of the default transport resource group configured on the cotransmission port.
If the NodeB or eNodeB side of a separate-MPT multimode base station provides a cotransmission port and co-transmission is implemented through panel interconnection, the traffic
control switch for a transport resource group must be disabled on the co-transmission port.
Otherwise, when transmission resources become congested, passing data will preempt
bandwidth from the local data. This deteriorates user experience.
1.
Run the ADD RSCGRP command to configure a default transport resource group on the
co-transmission port.
71
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
2.
7 Engineering Guidelines
Run the SET RSCGRPALG command to disable the traffic control switch of the default
transport resource group you have configured.
----End
//Configuring traffic limiting and shaping if the NodeB side of a separate-MPT multimode base
station provides a co-transmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//Configuring traffic limiting and shaping if the eNodeB side of a separate-MPT multimode base
station provides a co-transmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//Configuring traffic limiting and shaping if a co-MPT multimode base station provides a cotransmission port
SET LR: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, LRSW=ENABLE, CIR=20000,
CBS=40000, EBS=0;
//For a GBTS, binding an IP logical port and a GBTS on the Abis interface
SET BTSIP: IDTYPE=BYID, BTSID=1, BTSCOMTYPE=LOGICIP, BTSIP="16.16.90.201",
BSCIP="172.16.140.140", CFGFLAG=IPLGCPORT, SN=24, LPN=1;//In the preceding script,
the base station is identified by its base station index.
//For an eGBTS, binding an IP path and an IP logical port on the Abis interface if the peer end
is a BSC6900
Issue Draft A (2014-01-20)
72
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//For an eGBTS, binding an adjacent node and an IP logical port on the Abis interface if the peer
end is a BSC6910
ADD ADJLOGICPORTBIND: ANI=3, SRN=1, SN=24, LPN=1;
//Binding an IP path and an IP logical port if the transmission resource pool feature is not
implemented on the Iub interface
ADD IPPATH: ANI=10, PATHID=1, ITFT=IUB, TRANST=IP, PATHT=QoS,
IPADDR="172.16.100.140", PEERIPADDR="16.16.70.201", TXBW=20000, RXBW=20000,
CARRYFLAG=NULL, VLANFlAG=DISABLE, PATHCHK=DISABLED;
//Binding an adjacent node and an IP logical port if the transmission resource pool feature is
implemented on the Iub interface
ADD ADJLOGICPORTBIND: ANI=10, SRN=1, SN=26, LPN=1;
//Setting the mapping between DSCP values and data from the UP on the Abis interface
ADD
TRMMAP:TMI=111,ITFT=ABIS,TRANST=IP,CSVOICEPATH=EF,CSDATAPATH=AF41,PSHPRIDATAPATH=A
F41,PSLPRIDATAPATH=AF31;
//Setting the mapping between DSCP values and data from the CP on the Abis interface
SET BSCABISPRIMAP: IDTYPE=BYID, BTSID=1, TRANSTYPE=IP, OMLDSCP=48, RSLDSCP=48,
EMLDSCP=18, ESLDSCP=48;
//Adding the mapping from the Iub interface to the TRMMAP index
ADD ADJMAP: ANI=10, ITFT=IUB, TRANST=IP, CNMNGMODE=SHARE, TMIGLD=110, TMISLV=110,
TMIBRZ=110, FTI=1;
//Adding the mapping from the Abis interface to the TRMMAP index
ADD ADJMAP: ANI=3, ITFT=ABIS, TMIGLD=111, FTI=1;
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
BTSVLAN:
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
IDTYPE=BYID,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
BTSID=1,
SERVICETYPE=OML, DSCP=48;
SERVICETYPE=RSL, DSCP=48;
SERVICETYPE=EML, DSCP=18;
SERVICETYPE=ESL, DSCP=48;
SERVICETYPE= CSVOICE, DSCP=46;
SERVICETYPE= CSDATA, DSCP=34;
SERVICETYPE= PSHIGHPRI, DSCP=34;
SERVICETYPE= PSLOWPRI, DSCP=26;
SERVICETYPE= OTHERDATA, DSCP=46;
73
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Setting the mapping between DSCP values and data from the CP of an eGBTS
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the CP of a NodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the CP of an eNodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the UP of an eNodeB
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRPID=40,
UDTPARAGRPID=41,
UDTPARAGRPID=42,
UDTPARAGRPID=43,
UDTPARAGRPID=44,
UDTPARAGRPID=45,
UDTPARAGRPID=46,
UDTPARAGRPID=47,
UDTPARAGRPID=48,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRI=46;
PRI=18;
PRI=18;
PRI=18;
PRI=0;
PRI=46,
PRI=26,
PRI=34,
PRI=26,
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
//Adding an HSDPA flow control parameter in the case of a separate-MPT multimode base
station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING;
//Adding an HSDPA flow control parameter in the case of a co-MPT multimode base station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING, FAIRSWTICH=ENABLE;
//Disabling the traffic control switch of the default transport resource group configured on the
co-transmission port
Issue Draft A (2014-01-20)
74
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Disabling the traffic control switch on the default transport resource group you have configured
SET RSCGRPALG: SN=6, BEAR=IP, SBT=BASE_BOARD, PT=ETH, RSCGRPID=DEFAULTPORT,
TCSW=DISABLE;
MO
NE
LR/LR/LR/LR
eGBTS, NodeB,
eNodeB, or co-MPT
multimode base
stations
IPLOGICPORT
BTSIP/IPPATH/
ADJLOGICPORTB
IND
BSC
IPPATH/
ADJLOGICPORTB
IND
RNC
TRMMAP
BSC
TRMMAP
RNC
BSCABISPRIMAP
BSC
ADJMAP
BSC
ADJMAP
RNC
BTSVLAN/DIFPRI
GBTS or eGBTS
DIFPRI
NodeB
DIFPRI
eNodeB
UDTPARAGRP
eNodeB
ULFLOWCTRLPA
RA
NodeB
75
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
SN
7 Engineering Guidelines
MO
NE
DLFLOWCTRLPA
RA
NodeB
RSCGRP
eGBTS, NodeB,
eNodeB, or co-MPT
multimode base
stations
RSCGRPALG
eGBTS, NodeB,
eNodeB, or co-MPT
multimode base
stations
2.
Bind a user-plane link for transmitting local data and the configured transport resource
group on the base station side.
NOTE
A user-plane link can be configured either in link mode or in end-point mode. In link mode, users
configure an IP path. In end-point mode, users configure an end point group that includes the IP
addresses of the local and peer ends.
76
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
e. Run the ADD UPPEER2EPGRP command to bind the added user-plane peer and
the added end point group on the base station side.
f. Run the ADD EP2RSCGRP command to bind the added end point group and the
configured transport resource group.
3.
Run the ADD IP2RSCGRP command to bind a user-plane link for transmitting passing
data and a transport resource group on the base station side.
l Scenario 2: The eNodeB side of a separate-MPT multimode base station provides a cotransmission port.
1.
2.
Bind a user-plane link for transmitting local data and the configured transport resource
group on the base station side.
l If you use link mode to configure a user-plane link:
a. Run the ADD IPPATH command to add an IP path and bind this IP path and the
configured transport resource group.
b. Run the ADD ENODEBPATH command to bind an eNodeB and the added IP path.
l If you use end-point mode to configure a user-plane link:
a. Run the ADD EPGROUP command to add an end point group on the base station
side.
b. Run the ADD USERPLANEHOST command to add a user-plane host on the base
station side.
c. Run the ADD USERPLANEPEER command to add a user-plane peer on the base
station side.
d. Run the ADD UPHOST2EPGRP command to bind the added user-plane host and
the added end point group on the base station side.
e. Run the ADD UPPEER2EPGRP command to bind the added user-plane peer and
the added end point group on the base station side.
f. Run the ADD EP2RSCGRP command to bind the added end point group and the
configured transport resource group.
3.
Run the ADD IP2RSCGRP command to bind a user-plane link for transmitting passing
data and a transport resource group on the base station side.
2.
Bind a user-plane link and the configured transport resource group on the base station side.
l If you use link mode to configure a user-plane link:
a. Run the ADD IPPATH command to add an IP path and bind this IP path and the
configured transport resource group. In this step, set Peer IP to the RNC IP address.
b. Run the ADD NODEBPATH command to bind a NodeB and the added IP path.
c. Run the ADD IPPATH command to bind the added IP path and the configured
transport resource group. In this step, set Peer IP to the SeGW IP address.
d. Run the ADD ENODEBPATH command to bind an eNodeB and the added IP path.
l If you use end-point mode to configure a user-plane link:
a. Run the ADD EPGROUP command to add an end point group on the base station
side.
77
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
b. Run the ADD USERPLANEHOST command to add a user-plane host on the base
station side.
c. Run the ADD USERPLANEPEER command to add a user-plane peer on the base
station side.
d. Run the ADD UPHOST2EPGRP command to bind the added user-plane host and
the added end point group on the base station side.
e. Run the ADD UPPEER2EPGRP command to bind the added user-plane peer and
the added end point group on the base station side.
f. Run the ADD EP2RSCGRP command to bind the added end point group and the
configured transport resource group.
Step 2 Configure logical ports on the base station controller side.
1.
Run the ADD IPLOGICPORT command to add an IP logical port on the Iub interface.
2.
Run the ADD IPPATH command to bind a user-plane link and an IP logical port on the
Iub interface on the base station controller side.
Run the ADD TRMMAP command to set the mapping between DSCP values and data
from the UP and CP on the Iub interface.
2.
Run the ADD ADJMAP command to add the mapping from the Iub interface to the
TRMMAP index.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of a NodeB.
2.
Run the SET DIFPRI command to set the mapping between DSCP values and data from
the CP of an eNodeB.
3.
Run the MOD UDTPARAGRP command to set the mapping between DSCP values and
data from the UP of an eNodeB.
Step 5 Configure the dynamic flow control algorithm for the NodeB.
1.
Run the ADD ULFLOWCTRLPARA command to add an HSUPA flow control parameter
to set the uplink bandwidth adaptive flow control switch.
2.
Run the ADD DLFLOWCTRLPARA command to add an HSDPA flow control parameter
to set the HSDPA flow control switch.
Step 6 Disable the traffic control switch of the default transport resource group configured on the cotransmission port.
If the NodeB or eNodeB side of a separate-MPT multimode base station provides a cotransmission port and co-transmission is implemented through panel interconnection, the traffic
control switch for a transport resource group must be disabled on the co-transmission port.
Otherwise, when transmission resources become congested, passing data will preempt
bandwidth from the local data. This deteriorates user experience. Run the SET RSCGRPALG
Issue Draft A (2014-01-20)
78
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
command to disable the traffic control switch of the default transport resource group you have
configured.
----End
EPGROUP: EPGROUPID=0;
EPGROUP: EPGROUPID=1;
USERPLANEHOST: UPHOSTID=0, IPVERSION=IPv4, LOCIPV4="16.16.70.201";
USERPLANEHOST: UPHOSTID=1, IPVERSION=IPv4, LOCIPV4="16.16.60.201";
USERPLANEPEER: UPPEERID=0, IPVERSION=IPv4, LOCIPV4="172.16.90.140";
USERPLANEPEER: UPPEERID=1, IPVERSION=IPv4, LOCIPV4="172.16.80.140";
UPHOST2EPGRP: EPGROUPID=0, UPHOSTID=0;
UPHOST2EPGRP: EPGROUPID=1, UPHOSTID=1;
UPPEER2EPGRP: EPGROUPID=0, UPPEERID=0;
UPPEER2EPGRP: EPGROUPID=1, UPPEERID=1;
EP2RSCGRP: ENDPOINTID=0, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=1;
EP2RSCGRP: ENDPOINTID=1, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=2;
//Binding the passing data and the configured transport resource group
ADD IP2RSCGRP: SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=1, DSTIP="172.15.90.140",
DSTMASK="255.255.255.255";
ADD IP2RSCGRP: SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=2, DSTIP="172.15.80.140",
DSTMASK="255.255.255.255";
//If the eNodeB side of a separate-MPT multimode base station provides a co-transmission port
//Configuring a transport resource group
ADD RSCGRP: SN=6, BEAR=IP, SBT=BASE_BOARD, PT=ETH, PN=0, RSCGRPID=1, RU=KBPS,
TXBW=10000, RXBW=10000, TXCBS=20000, TXEBS=64, OID=0, WEIGHT=100, TXCIR=10000,
RXCIR=10000, TXPIR=10000, RXPIR=10000, TXPBS=10000;
79
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
EPGROUP: EPGROUPID=0;
EPGROUP: EPGROUPID=1;
USERPLANEHOST: UPHOSTID=0, IPVERSION=IPv4, LOCIPV4="16.15.70.201";
USERPLANEHOST: UPHOSTID=1, IPVERSION=IPv4, LOCIPV4="16.15.60.201";
USERPLANEPEER: UPPEERID=0, IPVERSION=IPv4, LOCIPV4="172.15.90.140";
USERPLANEPEER: UPPEERID=1, IPVERSION=IPv4, LOCIPV4="172.15.80.140";
UPHOST2EPGRP: EPGROUPID=0, UPHOSTID=0;
UPHOST2EPGRP: EPGROUPID=1, UPHOSTID=1;
UPPEER2EPGRP: EPGROUPID=0, UPPEERID=0;
UPPEER2EPGRP: EPGROUPID=1, UPPEERID=1;
EP2RSCGRP: ENDPOINTID=0, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=1;
EP2RSCGRP: ENDPOINTID=1, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=2;
//Binding the passing data and the configured transport resource group
ADD IP2RSCGRP: SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=1, DSTIP="172.16.90.140",
DSTMASK="255.255.255.255";
ADD IP2RSCGRP: SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=2, DSTIP="172.16.80.140",
DSTMASK="255.255.255.255";
RSCGRPID=1,
RSCGRPID=2,
RSCGRPID=1,
RSCGRPID=2,
80
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
EPGROUP: EPGROUPID=0;
EPGROUP: EPGROUPID=1;
EPGROUP: EPGROUPID=2;
EPGROUP: EPGROUPID=3;
USERPLANEHOST: UPHOSTID=0, IPVERSION=IPv4, LOCIPV4="16.16.70.201";
USERPLANEHOST: UPHOSTID=1, IPVERSION=IPv4, LOCIPV4="16.16.60.201";
USERPLANEHOST: UPHOSTID=2, IPVERSION=IPv4, LOCIPV4="16.15.70.201";
USERPLANEHOST: UPHOSTID=3, IPVERSION=IPv4, LOCIPV4="16.15.60.201";
USERPLANEPEER: UPPEERID=0, IPVERSION=IPv4, LOCIPV4="172.16.90.140";
USERPLANEPEER: UPPEERID=1, IPVERSION=IPv4, LOCIPV4="172.16.80.140";
USERPLANEPEER: UPPEERID=2, IPVERSION=IPv4, LOCIPV4="172.15.90.140";
USERPLANEPEER: UPPEERID=3, IPVERSION=IPv4, LOCIPV4="172.15.80.140";
UPHOST2EPGRP: EPGROUPID=0, UPHOSTID=0;
UPHOST2EPGRP: EPGROUPID=1, UPHOSTID=1;
UPHOST2EPGRP: EPGROUPID=2, UPHOSTID=2;
UPHOST2EPGRP: EPGROUPID=3, UPHOSTID=3;
UPPEER2EPGRP: EPGROUPID=0, UPPEERID=0;
UPPEER2EPGRP: EPGROUPID=1, UPPEERID=1;
UPPEER2EPGRP: EPGROUPID=0, UPPEERID=2;
UPPEER2EPGRP: EPGROUPID=1, UPPEERID=3;
EP2RSCGRP: ENDPOINTID=0, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=1;
EP2RSCGRP: ENDPOINTID=2, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=1;
EP2RSCGRP: ENDPOINTID=1, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=2;
EP2RSCGRP: ENDPOINTID=3, SN=6, SBT=BASE_BOARD, PT=ETH, RSCGRPID=2;
//Binding an IP path and the logical port you have added on the Iub interface
ADD IPPATH: ANI=10, PATHID=1, ITFT=IUB, TRANST=IP, PATHT=QoS,
IPADDR="172.16.90.140", PEERIPADDR="16.16.70.201", TXBW=10000, RXBW=10000,
CARRYFLAG=NULL, VLANFlAG=DISABLE, PATHCHK=DISABLED;
ADD IPPATH: ANI=10, PATHID=2, ITFT=IUB, TRANST=IP, PATHT=QoS,
IPADDR="172.16.80.140", PEERIPADDR="16.16.60.201", TXBW=10000, RXBW=10000,
CARRYFLAG=NULL, VLANFlAG=DISABLE, PATHCHK=DISABLED;
//Adding the mapping from the Iub interface to the TRMMAP index
Issue Draft A (2014-01-20)
81
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Setting the mapping between DSCP values and data from the CP of an eNodeB
SET DIFPRI: PRIRULE=DSCP, SIGPRI=48, OMHIGHPRI=46, OMLOWPRI=18, IPCLKPRI=46;
//Setting the mapping between DSCP values and data from the UP of an eNodeB
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRP:
UDTPARAGRPID=40,
UDTPARAGRPID=41,
UDTPARAGRPID=42,
UDTPARAGRPID=43,
UDTPARAGRPID=44,
UDTPARAGRPID=45,
UDTPARAGRPID=46,
UDTPARAGRPID=47,
UDTPARAGRPID=48,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRIRULE=DSCP,
PRI=46;
PRI=18;
PRI=18;
PRI=18;
PRI=0;
PRI=46,
PRI=26,
PRI=34,
PRI=26,
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
ACTFACTOR=100;
//Adding an HSDPA flow control parameter in the case of a separate-MPT multimode base
station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING;
//Adding an HSDPA flow control parameter in the case of a co-MPT multimode base station
ADD DLFLOWCTRLPARA: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BEAR=IP, PT=ETH, PN=0,
SWITCH= NO_BW_SHAPING, FAIRSWTICH=ENABLE;
82
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
//Disabling the traffic control switch of the default transport resource group configured on the
co-transmission port
//Configuring a default transport resource group on the co-transmission port in a separate-MPT
multimode base station where co-transmission is implemented through panel interconnection
SET RSCGRPALG: SN=6, BEAR=IP, SBT=BASE_BOARD, PT=ETH, RSCGRPID=1, TCSW=DISABLE;
SET RSCGRPALG: SN=6, BEAR=IP, SBT=BASE_BOARD, PT=ETH, RSCGRPID=2, TCSW=DISABLE;
MO
NE
RSCGRP
NodeB, eNodeB, or
co-MPT multimode
base stations
IPPATH
NodeB, eNodeB, or
co-MPT multimode
base stations
NODEBPATH
NodeB or co-MPT
multimode base
stations
ENODEBPATH
eNodeB or co-MPT
multimode base
stations
IP2RSCGRP
NodeB or eNodeB
IPLOGICPORT
RNC
IPPATH/
ADJLOGICPORTB
IND
RNC
TRMMAP
RNC
ADJMAP
RNC
DIFPRI
NodeB
DIFPRI
eNodeB
UDTPARAGRP
eNodeB
83
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
SN
5
7 Engineering Guidelines
MO
NE
ULFLOWCTRLPA
RA
NodeB
DLFLOWCTRLPA
RA
NodeB
RSCGRPALG
NodeB, eNodeB, or
multimode base
stations
Perform the following steps to determine whether this feature has been activated:
l
84
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
85
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Step 1 Initiate a UMTS or LTE PS service and set the maximum data rate higher than the CIR value
to simulate transmission resource congestion.
Step 2 Start transport link flux monitoring on the eGBTS LMT. Choose Monitor > Realtime
Performance Monitoring > Transport Link Flux Monitoring.
Step 3 Initiate a GSM or UMTS CS service if the traffic flux approaches the bandwidth available for
the bearer network.
Step 4 Terminate the CS service if the call is successfully set up and the voice is clear and constant.
Step 5 Initiate a GSM PS service, connect a personal computer (PC) to the multimode base station, and
use the DU Meter on the PC to check whether the GSM PS service is successfully set up and
the data rate is stable.
l If yes to both, this feature has been activated.
l If no to either, this feature has not been activated.
Step 6 Start IP or MAC tracing on the eGBTS LMT.
For IP tracing: Choose Trace > Common Services > IP Layer Protocol Trace. In the displayed
IP Layer Protocol Trace dialog box, specify Local IP Address and Peer IP Address of the
packets to be traced.
For MAC tracing: Choose Trace > Common Services > MAC Trace. In the displayed MAC
Trace dialog box, specify Local MAC Address and Peer MAC Address of the packets to be
traced.
Step 7 Use the TrafficReview tool to check the TOS field in the Layer 3 IP packet header or the VLAN
Priority field in the Layer 2 IP packet header. The first six bits in the TOS field indicate the
DSCP value of a packet. If the calculated DSCP values or VLAN priorities are the same as DSCP
values or VLAN priorities planned, this feature has been activated.
----End
l
The NodeB side of a separate-MPT multimode base station provides a co-transmission port.
Step 1 Initiate a UMTS PS service and set the maximum data rate higher than the CIR value to simulate
transmission resource congestion.
Step 2 Start transport link flux monitoring on the NodeB LMT. Choose Monitor > Realtime
Performance Monitoring > Transport Link Flux Monitoring.
Step 3 Initiate a GSM or UMTS CS service if the traffic flux approaches the bandwidth available for
the bearer network.
Step 4 Terminate the CS service if the call is successfully set up and the voice is clear and constant.
Step 5 Initiate a GSM PS service, connect a PC to the multimode base station, and use the DU Meter
on the PC to check whether the GSM PS service is successfully set up and the data rate is stable.
l If yes, this feature has been activated.
l If no, this feature has not been activated.
NOTE
Step 5 is performed only in a separate-MPT GU dual-mode base station or a separate-MPT GUL triplemode base station.
86
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Step 1 Initiate an LTE PS service and set the maximum data rate higher than the CIR value to simulate
transmission resource congestion.
Step 2 Start transport link flux monitoring on the eNodeB LMT. Choose Monitor > Realtime
Performance Monitoring > Transport Link Flux Monitoring.
Step 3 Initiate a GSM or UMTS CS service if the traffic flux approaches the bandwidth available for
the bearer network.
Step 4 Terminate the CS service if the call is successfully set up and the voice is clear and constant.
Initiate a GSM PS service, connect a PC to the multimode base station, and use the DU Meter
on the PC to check whether the GSM PS service is successfully set up and the data rate is stable.
l If yes, this feature has been activated.
l If no, this feature has not been activated.
NOTE
Step 4 is performed only in a separate-MPT GL dual-mode base station or a separate-MPT GUL triplemode base station.
87
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Step 1 Initiate a UMTS or LTE PS service and set the maximum data rate higher than the CIR value
to simulate transmission resource congestion.
Step 2 Start transport link flux monitoring on the LMT.
l If UMTS services are initiated, start transport link flux monitoring on the LMT. Choose
Monitor > Realtime Performance Monitoring > Transport Link Flux Monitoring.
l If LTE services are initiated, start transport link flux monitoring on the LMT. Choose
Monitor > Realtime Performance Monitoring > Transport Link Flux Monitoring.
Step 3 Initiate a GSM or UMTS CS service if the traffic flux approaches the bandwidth available for
the bearer network.
Step 4 Terminate the CS service if the call is successfully set up and the voice is clear and constant.
Initiate a GSM PS service, connect a PC to the multimode base station, and use the DU Meter
on the PC to check whether the GSM PS service is successfully set up and the data rate is stable.
l If yes, this feature has been activated.
l If no, this feature has not been activated.
NOTE
Step 4 is performed only in a separate-MPT GU/GL dual-mode base station or a separate-MPT GUL triplemode base station.
88
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
DSCP value of a packet. If the calculated DSCP values or VLAN priorities are the same as DSCP
values or VLAN priorities planned, this feature has been activated.
----End
Step 1 Initiate a UMTS or LTE PS service for operator A and set the maximum data rate higher than
the TXBW value to simulate transmission resource congestion.
Step 2 Start transport link flux monitoring on the LMT.
l If the NodeB side of a separate-MPT multimode base station provides a co-transmission port,
start transport link flux monitoring on the NodeB LMT. Choose Monitor > Realtime
Performance Monitoring > Transport Link Flux Monitoring.
l If the eNodeB side of a separate-MPT multimode base station provides a co-transmission
port, start transport link flux monitoring on the eNodeB LMT. Choose Monitor > Realtime
Performance Monitoring > Transport Link Flux Monitoring.
Step 3 Initiate a UMTS CS service for operator A if the traffic flux approaches the bandwidth available
for the bearer network. Terminate the CS service if the call is successfully set up and the voice
is clear and constant.
Step 4 Perform the first three steps to verify services of other operators.
Step 5 Start IP or MAC tracing on the LMT.
l Start IP or MAC tracing on the NodeB LMT.
For IP tracing: Choose Trace > Common Services > IP Layer Protocol Trace. In the
displayed IP Layer Protocol Trace dialog box, specify Local IP Address and Peer IP
Address of the packets to be traced.
For MAC tracing: Choose Trace > Common Services > MAC Trace. In the displayed
MAC Trace dialog box, specify Local MAC Address and Peer MAC Address of the
packets to be traced.
Issue Draft A (2014-01-20)
89
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
Step 1 Initiate a UMTS or LTE PS service for operator A and set the maximum data rate higher than
the TXBW value to simulate transmission resource congestion.
Step 2 Start transport link flux monitoring on the LMT.
l If UMTS services are initiated, start transport link flux monitoring on the NodeB LMT.
Choose Monitor > Realtime Performance Monitoring > Transport Link Flux
Monitoring.
l If LTE services are initiated, start transport link flux monitoring on the eNodeB LMT. Choose
Monitor > Realtime Performance Monitoring > Transport Link Flux Monitoring.
Step 3 Initiate a UMTS CS service for operator A if the traffic flux approaches the bandwidth available
for the bearer network. Terminate the CS service if the call is successfully set up and the voice
is clear and constant.
Step 4 Perform the first three steps to verify services of other operators.
Step 5 Start IP or MAC tracing on the LMT.
l If UMTS services are initiated, start IP or MAC tracing on the NodeB LMT.
For IP tracing: Choose Trace > Common Services > IP Layer Protocol Trace. In the
displayed IP Layer Protocol Trace dialog box, specify Local IP Address and Peer IP
Address of the packets to be traced.
For MAC tracing: Choose Trace > Common Services > MAC Trace. In the displayed
MAC Trace dialog box, specify Local MAC Address and Peer MAC Address of the
packets to be traced.
l If LTE services are initiated, start IP or MAC tracing on the eNodeB LMT.
For IP tracing: Choose Trace > Common Services > IP Layer Protocol Trace. In the
displayed IP Layer Protocol Trace dialog box, specify Local IP Address and Peer IP
Address of the packets to be traced.
For MAC tracing: Choose Trace > Common Services > MAC Trace. In the displayed
MAC Trace dialog box, specify Local MAC Address and Peer MAC Address of the
packets to be traced.
Step 6 Use the TrafficReview tool to check the TOS field in the Layer 3 IP packet header or the VLAN
Priority field in the Layer 2 IP packet header. The first six bits in the TOS field indicate the
Issue Draft A (2014-01-20)
90
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
7 Engineering Guidelines
DSCP value of a packet. If the calculated DSCP values or VLAN priorities are the same as DSCP
values or VLAN priorities planned, this feature has been activated.
----End
7.7 Troubleshooting
If bandwidth resources across all modes of a multimode base station are inappropriately
allocated, reallocate the bandwidth resources based on the traffic model.
91
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameters
NE
MML
Command
Feature ID
Feature Name
Description
CIR
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET LR
WRFD-010610
10
HSDPA Flow
Control
Meaning:Indicates the UL
committed
information rate
after rate
limitation is
configured at a
port. The
precision of the
UL committed
information rate
supported by the
UMPTb is 64
Kbit/s, the
precision
supported by the
other board is 32
Kbit/s. If the
configured UL
committed
information rate
is not a multiple
of the precision,
the UL
committed
information rate
is rounded up.
LST LR
GUI Value
Range:
32~1000000
Unit:Kbit/s
Issue Draft A (2014-01-20)
92
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
Actual Value
Range:
32~1000000
Default
Value:None
93
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
TXBW
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
ADD RSCGRP
WRFD-021304
06
Transmission
Recourse
Sharing on Iub/
Iur Interface
Meaning:Indicates the
maximum
uplink
bandwidth of a
transmission
resource group
at the MAC
layer when the
transmission
resource group
is carried over
IP. This
parameter value
is used as the
uplink transport
admission
bandwidth and
TX traffic
shaping
bandwidth.The
LMPT can be
configured with
a maximum of
360 Mbit/s TX
bandwidth.The
WMPT can be
configured with
a maximum of
300 Mbit/s TX
bandwidth.The
UMPT can be
configured with
a maximum of 1
Gbit/s TX
bandwidth.The
value of TX
bandwidth is set
to the maximum
value of TX
bandwidth
supported by the
board when it
bigger than the
maximum one.
MOD RSCGRP
DSP RSCGRP
LST RSCGRP
94
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
GUI Value
Range:
32~1000000
Unit:None
Actual Value
Range:
32~1000000
Default
Value:None
CIR
BSC6900
ADD
IPLOGICPORT
WRFD-050408
MOD
IPLOGICPORT
WRFD-021311
WRFD-140208
WRFD-140207
Overbooking on
IP Transmission
Iub
Transmission
Resource Pool
in RNC
MOCN
Introduction
Package
Iu/Iur
Transmission
Resource Pool
in RNC
Meaning:Bandwidth of the
logical port
GUI Value
Range:1~1562
Unit:64kbit/s
Actual Value
Range:
64~64000
(FG2a/GOUa/
UOIa(IP)),
256~100000
(FG2c/GOUc/
POUc(IP)/PEUc
(IP)/GOUe)
Default
Value:None
CIR
BSC6910
ADD
IPLOGICPORT
WRFD-050408
Overbooking on
IP Transmission
MOD
IPLOGICPORT
Meaning:Bandwidth of the
logical port.
GUI Value
Range:4~1562
Unit:64kbit/s
Actual Value
Range:
256~100000
Default
Value:None
95
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
TNLCONGCT
RLSWITCH
BTS3900,
BTS3900
WCDMA
ADD
ULFLOWCTR
LPARA
None
None
Meaning:Indicates whether to
perform
congestion
control. When
this switch is
turned on, the
BS lowers the
TX rate if the BS
detects that links
experience
transmission
delay or packet
loss.It is
recommended
that this switch
be turned off if
UMTS and LTE
services are
configured in
the same
transmission
resource group.
The purpose is to
prevent UMTS
flow control
from affecting
LTE services.
SET
ULFLOWCTR
LPARA
LST
ULFLOWCTR
LPARA
GUI Value
Range:OFF
(Off), ON(On)
Unit:None
Actual Value
Range:OFF, ON
Default
Value:ON(On)
96
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
TCSW
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET
RSCGRPALG
LOFD-0030110
1/
TDLOFD-0030
1101
Transport
Overbooking
Meaning:Indicates whether to
enable the
backpressure
algorithm of a
transmission
resource group.
The BS
monitors the
data buffered in
the queues of
each
transmission
resource group,
determines
whether the
transmission
resource group
is congested,
and transmits
the backpressure
signals (number
and congestion
status of the
transmission
resource group)
to each flow
control service.
If the number of
data packets in
the buffer of any
backpressure
queue exceeds
75% of the
queue capacity,
the BS regards
this
transmission
resource group
as congested and
transmits
congestion
signals. If the
buffered backpressure packets
are less than
50% of the total
buffer capacity,
LST
RSCGRPALG
LOFD-0030110
2/
TDLOFD-0030
1102
Transport
Differentiated
Flow Control
97
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
the BS decides
that the
transmission
resource group
is not congested.
In this situation,
no congestion
signal or
congestion
release signal is
transmitted.
When this
parameter is set
to ENABLE,
both intra-mode
and inter-mode
traffic controls
are supported.
The inter-mode
traffic control
for transmission
resource groups
applies only to
separate-MPT
base stations
with cotransmission
implemented
through
backplane
interconnection.
However, it does
not apply to
cascaded base
stations, base
stations with cotransmission
implemented
through panel
interconnection,
or base stations
enabled with
route load
sharing. When
the inter-mode
traffic control
function is
enabled for a
98
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
separate-MPT
base station with
co-transmission
implemented
through
backplane
interconnection,
the Tunnel Type
parameter must
be set to DL(DL)
for the tunnel of
the mode
providing
transmission
ports and must
be set to UL(UL)
for the tunnel of
the mode
providing no
transmission
port.
GUI Value
Range:DISABL
E(Disable),
ENABLE
(Enable)
Unit:None
Actual Value
Range:DISABL
E, ENABLE
Default
Value:ENABLE
(Enable)
99
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
SWITCH
BTS3900,
BTS3900
WCDMA
ADD
DLFLOWCTR
LPARA
WRFD-010610
10
HSDPA Flow
Control
SET
DLFLOWCTR
LPARA
LST
DLFLOWCTR
LPARA
100
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
the air interface
conditions to the
controller, and
then the
controller
allocates
bandwidth.
When this
parameter is set
to
NO_BW_SHAP
ING, the
backpressure
function must be
enabled on the
controller side.
If this parameter
is set to
BW_SHAPING
_ONOFF_TOG
GLE, the BS
automatically
selects either
DYNAMIC_B
W_SHAPING
or
NO_BW_SHAP
ING during a
flow congestion
detection on a
port. That is,
DYNAMIC_B
W_SHAPING is
selected if
congestion is
detected;
NO_BW_SHAP
ING is selected
if congestion is
not detected for
a certain period
of time.
GUI Value
Range:STATIC
_BW_SHAPIN
G
(STATIC_BW_
101
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
SHAPING),
DYNAMIC_B
W_SHAPING
(DYNAMIC_B
W_SHAPING),
NO_BW_SHAP
ING
(NO_BW_SHA
PING),
BW_SHAPING
_ONOFF_TOG
GLE
(BW_SHAPIN
G_ONOFF_TO
GGLE)
Unit:None
Actual Value
Range:STATIC
_BW_SHAPIN
G,
DYNAMIC_B
W_SHAPING,
NO_BW_SHAP
ING,
BW_SHAPING
_ONOFF_TOG
GLE
Default
Value:BW_SH
APING_ONOF
F_TOGGLE
(BW_SHAPIN
G_ONOFF_TO
GGLE)
102
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
FAIRSWITCH
BTS3900,
BTS3900
WCDMA
ADD
DLFLOWCTR
LPARA
WRFD-010610
10
HSDPA Flow
Control
SET
DLFLOWCTR
LPARA
LST
DLFLOWCTR
LPARA
103
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
GUI Value
Range:OFF
(Off), ON(On)
Unit:None
Actual Value
Range:OFF, ON
Default
Value:OFF(Off)
CBS
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET LR
LST LR
WRFD-050402
IP Transmission
Introduction on
Iub Interface
Meaning:Indicates the
Committed
Burst Size
(CBS) after rate
limitation is
configured at a
port.The
minimum rate
supported by the
UMPTb is 64
Kbit/s.
GUI Value
Range:
32~1000000
Unit:Kbit
Actual Value
Range:
32~1000000
Default
Value:None
104
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
EBS
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET LR
WRFD-050402
IP Transmission
Introduction on
Iub Interface
LST LR
GUI Value
Range:
0~1000000
Unit:Kbit
Actual Value
Range:
0~1000000
Default
Value:None
105
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
TXCBS
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
ADD RSCGRP
WRFD-021304
06
Transmission
Recourse
Sharing on Iub/
Iur Interface
Meaning:Indicates the TX
committed burst
size of a
transmission
resource
group.The
LMPT can be
configured with
a maximum of
400 Mbit/s TX
committed burst
size.The WMPT
can be
configured with
a maximum of
600 Mbit/s TX
committed burst
size.The WMPT
can be
configured with
a maximum of
600 Mbit/s TX
committed burst
size.The UMPT
can be
configured with
a maximum of 1
Gbit/s TX
committed burst
size.The value
of TX
committed burst
size is set to the
maximum value
of TX
committed burst
size supported
by the board
when it bigger
than the
maximum one.
MOD RSCGRP
LST RSCGRP
GUI Value
Range:
64~1000000
Unit:Kbit
106
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
Actual Value
Range:
64~1000000
Default Value:
64
107
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
TXEBS
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
ADD RSCGRP
WRFD-021304
06
Transmission
Recourse
Sharing on Iub/
Iur Interface
Meaning:Indicates the TX
excessive burst
size of a
transmission
resource
group.The
LMPT can be
configured with
a maximum of
450 Mbit/s TX
excessive burst
size.The WMPT
can be
configured with
a maximum of
600 Mbit/s TX
excessive burst
size.The UMPT
can be
configured with
a maximum of 1
Gbit/s TX
excessive burst
size.The value
of TX excessive
burst size is set
to the maximum
value of TX
excessive burst
size supported
by the board
when it bigger
than the
maximum one.
MOD RSCGRP
LST RSCGRP
GUI Value
Range:
64~1000000
Unit:Kbit
Actual Value
Range:
64~1000000
Default Value:
1000000
108
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
LPN
BSC6900
ADD
IPLOGICPORT
WRFD-140208
Iub
Transmission
Resource Pool
in RNC
Meaning:Logica
l port number. It
is uniquely
numbered
within the
active/standby
boards.
WRFD-140207
MOD
IPLOGICPORT
Iu/Iur
Transmission
Resource Pool
in RNC
RMV
IPLOGICPORT
GUI Value
Range:
0~988;1024~15
35
Unit:None
Actual Value
Range:0~119
(FG2a/GOUa/
UOIa(IP));
0~489, 512~767
(FG2c); 0~499,
512~767
(GOUc/GOUe);
0~988,
1024~1535
(POUc(IP));
0~127,
1024~1087
(PEUc(IP))
Default
Value:None
LPN
BSC6910
ADD
IPLOGICPORT
None
None
Meaning:Logica
l port number.
MOD
IPLOGICPORT
GUI Value
Range:0~2047
RMV
IPLOGICPORT
Unit:None
Actual Value
Range:0~489
(FG2c, GOUc,
GOUe),
512~767(FG2c,
GOUc, GOUe);
0~1499
(EXOUa),
1536~2047
(EXOUa)
Default
Value:None
109
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PRIRULE
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET DIFPRI
WRFD-050402
IP Transmission
Introduction on
Iub Interface
LST DIFPRI
GUI Value
Range:IPPREC
EDENCE(IP
Precedence),
DSCP(DSCP)
Unit:None
Actual Value
Range:IPPREC
EDENCE,
DSCP
Default
Value:DSCP
(DSCP)
110
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
SIGPRI
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET DIFPRI
WRFD-050402
IP Transmission
Introduction on
Iub Interface
LST DIFPRI
GUI Value
Range:0~63
Unit:None
Actual Value
Range:0~63
Default Value:
48
OMHIGHPRI
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET DIFPRI
LST DIFPRI
WRFD-050402
IP Transmission
Introduction on
Iub Interface
111
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
OMLOWPRI
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET DIFPRI
WRFD-050402
IP Transmission
Introduction on
Iub Interface
LST DIFPRI
GUI Value
Range:0~63
Unit:None
Actual Value
Range:0~63
Default Value:
18
112
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
IPCLKPRI
BTS3900,
BTS3900
WCDMA,
BTS3900 LTE
SET DIFPRI
None
None
LST DIFPRI
GUI Value
Range:0~63
Unit:None
Actual Value
Range:0~63
Default Value:
46
113
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CCHPRIPATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:Primar
y path that
carries the
common
channel
services.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
114
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
115
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
SIPPRIPATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:This
parameter is
used to set IMS
SRB primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
116
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
117
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
SRBPRIPATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:Signal
ing service
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
118
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
119
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
VOICEPRIPAT
H
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:AMR
voice service
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
120
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
121
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CSCONVPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
CS
conversational
service primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
122
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
123
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CSSTRMPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
CS streaming
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
124
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
125
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PSCONVPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
PS
conversational
service primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
126
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
127
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PSSTRMPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
PS streaming
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
128
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
129
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PSINTHGHPRI
PATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
PS high PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
130
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
131
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PSINTMIDPRI
PATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
PS middle PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
132
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
133
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PSINTLOWPRI
PATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
PS low PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
134
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
135
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PSBKGPRIPA
TH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:R99
PS background
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
136
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
137
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDSRBPRIPA
TH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A signaling
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
138
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
139
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDSIPPRIPAT
H
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A IMS signaling
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
140
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
141
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDVOICEPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A voice service
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
142
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
143
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDCONVPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A
conversational
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
144
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
145
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDSTRMPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A streaming
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
146
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
147
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDINTHGHPR
IPATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A high PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
148
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
149
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDINTMIDPRI
PATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A middle PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
150
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
151
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDINTLOWPR
IPATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A low PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
152
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
153
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HDBKGPRIPA
TH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSDP
A background
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
154
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
155
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUSRBPRIPA
TH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A signaling
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
156
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
157
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUSIPPRIPAT
H
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A IMS signaling
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
158
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
159
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUVOICEPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A voice service
bearer primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
160
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
161
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUCONVPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A
conversational
service primary
path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
162
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
163
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUSTRMPRIP
ATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A streaming
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
164
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
165
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUINTHGHPR
IPATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A high PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
166
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
167
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUINTMIDPRI
PATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A middle PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
168
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
169
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUINTLOWPR
IPATH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A low PRI
interactive
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
170
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
171
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
8 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
HUBKGPRIPA
TH
BSC6900
ADD
TRMMAP
WRFD-050406
ATM QoS
Introduction on
Hub Node B
(Overbooking
on Hub Node B
Transmission)
Meaning:HSUP
A background
service bearer
primary path.
MOD
TRMMAP
GUI Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Unit:None
Actual Value
Range:CBR,
RT_VBR,
NRT_VBR,
UBR, BE,
AF11, AF12,
AF13, AF21,
AF22, AF23,
AF31, AF32,
AF33, AF41,
AF42, AF43,
EF, LQBE,
LQAF11,
LQAF12,
LQAF13,
LQAF21,
LQAF22,
LQAF23,
172
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
Parameter ID
NE
MML
Command
8 Parameters
Feature ID
Feature Name
Description
LQAF31,
LQAF32,
LQAF33,
LQAF41,
LQAF42,
LQAF43, LQEF
Default
Value:None
173
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
9 Counters
Counters
Counter Name
Counter
Description
NE
Feature ID
Feature Name
1542455378
VS.RscGroup.T
xFlowOverloadTime
Congestion
duration of
transmit data in
the resource
group
NodeB
Multi-mode:
MRFD-211505
Bandwidth
sharing of
MBTS Multimode CoTransmission
(GBTS)
MRFD-221505
MRFD-231505
MRFD-241505
GSM: None
UMTS: None
LTE: None
Bandwidth
sharing of
MBTS Multimode CoTransmission
(NodeB)
Bandwidth
sharing of
MBTS Multimode CoTransmission
(eNodeB)
Bandwidth
sharing of
MBTS Multimode CoTransmission
(LTE TDD)
174
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
10 Glossary
10
Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
175
SingleRAN
Bandwidth Sharing of Multimode Base Station CoTransmission Feature Parameter Description
11
11 Reference Documents
Reference Documents
1.
Transmission Resource Management Feature Parameter Description for GBSS and RAN
2.
3.
176