Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Styrolux
Material number STY005
Page:
1 of 9
Styrolux
This safety data sheet pertains to the following products:
Styrolux 3G46
Styrolux 3G55
Styrolux 656C
Styrolux 684D
Styrolux 684D NW
Styrolux HS70
Styrolux S
Styrolux T
Relevant identified uses of the substance or mixture and uses advised against
General use:
Polymer
For industrial processing only
2. Hazards identification
Emergency overview
Appearance:
Odor:
Classification:
Regulatory status
This material is not considered hazardous by the U.S. OSHA Hazard Communication
Standard (29 CFR 1910.1200) and SIMDUT in Canada.
Styrolux
Material number STY005
Page:
2 of 9
Additional information:
After swallowing:
Provide fresh air. Put victim at rest and keep warm. seek medical attention
The melted product can cause severe burns.
Do not remove the product from the skin without medical assistance.
After contact with molten product, cool skin area rapidly with cold water. Consult physician.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing.
Consult an eye specialist in the event of irritation.
Rinse mouth with water. Drink one or two glasses of water.
Never give an unconscious person anything through the mouth. seek medical attention
Information to physician
Treat symptomatically.
Decontamination, vital functions
> 536 F
no data available
Styrolux
Material number STY005
Additional information:
Page:
3 of 9
Do not allow fire water to penetrate into surface or ground water. Fire residuals and
contaminated extinguishing water must be disposed of in accordance with the regulations
of the local authorities.
Environmental precautions:
Additional information:
Provide adequate ventilation, and local exhaust as needed. Do not breathe dust.
In the case of the formation of dust: Withdraw by suction.
Molten material: Avoid contact with the substance.
Take precautionary measures against static discharges. Keep away from sources of
ignition. Use grounding equipment. Use explosion-proof equipment and non-sparking
tools/utensils. Avoid open flames.
In case of dust formation (fine dust): danger of dust explosion
Storage
Requirements for storerooms and containers:
Styrolux
Material number STY005
Page:
4 of 9
Type
USA: ACGIH: TWA
USA: ACGIH: TWA
USA: OSHA: TWA
USA: OSHA: TWA
100-42-5 Styrene
OSHA: Ceiling
USA: ACGIH: STEL
USA: ACGIH: TWA
USA: NIOSH: STEL
USA: NIOSH: TWA
USA: OSHA: TWA
106-99-0 1,3-Butadiene USA: ACGIH: TWA
USA: OSHA: STEL
USA: OSHA: TWA
Limit value
10 mg/m
3 mg/m
15 mg/m
5 mg/m
200 ppm
170 mg/m; 40 ppm
85 mg/m; 20 ppm
425 mg/m; 100 ppm
215 mg/m; 50 ppm
100 ppm
4.4 mg/m; 2 ppm
11 mg/m; 5 ppm
2.21 mg/m; 1 ppm
Type
USA:
ACGIH-BEI,
blood
USA:
ACGIH-BEI, urine
106-99-0 1,3-Butadiene USA:
ACGIH-BEI,
blood
USA:
ACGIH-BEI, urine
Additional information:
Limit value
Parameter
Sampling
0.2 mg/L
end of exposure
or end of shift
400 mg/g
Mandelic acid +
creatinine
Phenylglyoxylic acid
2.5 pmol/g Hb Mixture of N-1 and
N2-(hydroxybutenyl)valine
hemoglobin (Hb) adduts
2.5 mg/L
1,2
Dihydroxy-4-(Nacetylcysteinyl)-butane
end of exposure
or end of shift
No restriction
end of exposure
or end of shift
The product contains very low levels of residual monomers and process chemicals
(styrene, ethylbenzene and butadiene) that may be evolved during thermal processing,
along with possible decomposition products. As the identity and levels of these impurities
evolved will depend upon the processing conditions (temperature etc.) it is the
responsibility of the user to determine the adequacy of any protection or safety measures.
Engineering controls
Provide good ventilation in the work area. Additional controls are not normally necessary
when handling the polymer.
Thermal extrusion: Provide local exhaust ventilation to ensure that the workplace exposure
limit is not exceeded.
Use of respiratory protection may be necessary during maintenance activities.
See also information in chapter 7, section storage.
Skin protection
Styrolux
Material number STY005
Respiratory protection:
Page:
5 of 9
Appearance:
Odor:
Odor threshold:
pH value:
Melting point/freezing point:
Initial boiling point and boiling range:
Flash point/flash point range:
Evaporation rate:
Flammability:
Explosive properties:
Explosion limits:
Vapor pressure:
Vapor density:
Density:
Water solubility:
Partition coefficient: n-octanol/water:
Auto-ignition temperature:
Thermal decomposition:
no data available
> 86 F (DIN EN ISO 306)
no data available
> 536 F
no data available
no data available
Dust explosion risk at fine dust
no data available
no data available
no data available
no data available
at 68 F: approx. 1.05 g/cm (DIN 53479)
insoluble
no data available
no data available
approx. 572 F
Not oxidising
> 752 F (DIN 51794)
at 68 F: approx. 640 kg/m (DIN 53466)
Oxidizing characteristics:
Ignition temperature:
Bulk density:
no data available
Styrolux
Material number STY005
Chemical stability:
Page:
6 of 9
Keep away from open flames, hot surfaces and sources of ignition.
Avoid dust formation.
Incompatible materials:
In case of fire may be liberated: smoke, carbon monoxide and carbon dioxide (CO2).
approx. 572 F
Other information:
Symptoms
Dust: Can cause skin, eye and respiratory tract irritation.
The melted product can cause severe burns.
Thermal treatment, Processing:
Irritating to eyes, respiratory system and skin.
In case of ingestion: Swallowing may cause gastrointestinal irritation and pain of guts.
Styrolux
Material number STY005
Further details:
Page:
7 of 9
Pellets may accumulate in the digestive systems of birds and aquatic life, causing injury
and possible death due to starvation.
Mobility in soil
no data available
With due observance of the regulations laid down by the local authorities, this must be
brought to a suitable incineration plant/waste disposal site.
Contaminated packaging
Recommendation:
Dispose of waste according to applicable legislation.
Non-contaminated packages may be recycled.
Not restricted
No
Not restricted
Further information
No dangerous good in sense of these transport regulations.
Styrolux
Material number STY005
Page:
8 of 9
Styrolux
Material number STY005
Page:
9 of 9
HEALTH
FLAMMABILITY
PHYSICAL HAZARD
R phrase(s):
S phrase(s):
not applicable
not applicable
not applicable
The information in this data sheet has been established to our best knowledge and was up-to-date at time of
revision. It does not represent a guarantee for the properties of the product described in terms of the legal
warranty regulations.