Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
com
EC 2305 TRANSMISSION LINES AND WAVEGUIDES
DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
THIRD YEAR / FIFTH SEMESTER
Regulation 2008
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
MAY / JUNE 2012
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
NOV / DEC 2010
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
Zoc = -j R0 cot (2/lambda)s.
Zsc = jR0 tan (2/lambda)s.
7. Define the cutoff frequency for the guided waves.
The frequency bellow which the wave is attenuated exponentially and
above which the wave propagation occurs is called cutoff frequency.
The frequency at which wave motion ceases is called critical frequency
or cutoff frequency fc of a wave guide. At cutoff frequency fc.
8. For a frequency of 6GHz and plane separation of 3 cm, find the group
and phase velocities for the dominant mode.
Ans : C/P=5.42ms, CP=1.659m/s.
9. Calculate the cutoff wavelength for the TM11 mode in a standard
rectangular waveguide if a=4.5cm.
Ans: m=1 n=1
Lamdanot=4.02.
10.Give the applications of cavity resonators.
Used in cavity meters.
Used in klystron amplifiers.
Used in Reflex klystron oscillators and cavity magnetrons.
Used in duplexers in radar systems.
___________________________________________________________
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
APRIL / MAY - 2011
1. For a symmetrical network, define propagation constant and
characteristics impedance.
The current ratio or voltage ratio is expressed in exponential term
under the condition of Z0 termination.
Characteristic impedance of a symmetrical network is the impedance
measured at the input terminals of the first network in a chain of
infinite networks in cascade and is denoted as Z0.
2. What are the disadvantages of m-derived filters?
Attenuation rises sharply at cut off frequency.
In the pass band output of the filter remains constant which means the
characteristic impedance remains constant throughout the pass band.
3. How can distortion be reduced in a transmission line?
A line in which there is no phase or frequency distortion is called a
distortion less line. The condition for a distortion less line is given as
RC=LG.
4. A transmission line has Z0=745 12degree ohms and is terminated is
ZR=100ohm calculate the reflection loss in Db.
Answer: k=0.6475, 1/|k|=3.7751 dB
5. Express standingwave ratio in terms of a reflection coefficient.
S= 1+|K|/1-|K|
(OR)
|K|=S-1/S+1.
6. Mention the application of quarter waveline.
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
A quarter wave line is used for impedance matching.(i.e) it matches
the load with the sources and ensures that maximum power is being
transferred to the load.
Application:
i). used as a transformer to match a load ZR ohms.
ii). Used as impedance matching inverter.
iii). Used as couple a transmission line to a resistive load such as
an antenna.
7. The electric field in free space is given by E=50cos[10T+BX] V/M.
find the direction of wave propagation and Beta.
the wave is propagating along a
beta=w/c=1/3=0.333rad/m.
8. Define skin depth.
Skin depth is a measure of depths to which an Em wave can
penetrate the medium.
9. Compare transmission line and wave guide.
Answer:
TRASMISION LINE
WAVE GUIDE
1. May operate from DC to
It can operate only above a
very high frequency.
certain frequency called cutoff
frequency.
2. Inefficient due to skin
Larger bandwidth and lower
effect and dielectric loss.
attenuation.
10.An air filled resonant cavity with dimensions a= 5 cm, b= 4 cm, c=
10 cm is made of copper. Find the resonator frequency for lowest
order mode.
Answer: f101 = v/2 = 3.335 GHz.
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
Nov / Dec - 2011
1. What is the significance of propagation constant in symmetrical
network?
2. Draw the equivalent electrical circuit for a piezoelectric crystal.
3. When does a finite line appear as an infinite line?
4. If a line is to have neither frequency nor delay distortion, how do
your relate attenuation constant and velocity of propagation to
frequency?
5. For the line of zero dissipation. What will be the values of
attenuation constant and characteristic impedance?
6. Define standing wave ratio?
7. Write down the relationship between phase velocity and group
velocity?
8. Write down the equations for characteristic impedance for TM, and
TE waves.
9. A rectangular waveguide of cross section 5cm x 2cm is to propagate
TM11 mode at 10GHz. Determine the cutoff wavelength.
10.What is the need for guide termination?
MAY/JUNE - 2007
1. What is frequency distortion?
2. Calculate the load reflection coefficient of an open and short
circuited line.
3. Find the VSWR and reflection coefficient of a perfectly matched
line with no reflection from load?
4. Name the few applications of half wave line.
5. What is the cut off frequency of TEM Waves?
6. Give the expression that relates phase, group, free space
velocities.
7. Why the TE10 wave is called as dominant mode?
8. How the TE10 mode is launched?
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
9. Define the quality factor of a cavity resonator.
10.What is cavity resonator?
TWO MARKS
Answers
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
WWW.VIDYARTHIPLUS.COM
www.Vidyarthiplus.com
WWW.VIDYARTHIPLUS.COM