Sei sulla pagina 1di 7

Ordering number : ENN7047

Thick-Film Hybrid IC

STK402-070
Two-Channel Class AB Audio Power Amplifier IC
40W + 40W

Overview Package Dimensions


The STK402-000 series products are audio power unit: mm
amplifier hybrid ICs that consist of optimally-designed 4189-SIP15
discrete component power amplifier circuits that have
been miniaturized using SANYO's unique insulated metal [STK402-070]
substrate technology (IMST). SANYO has adopted a new
low thermal resistance substrate in these products to
reduce the package size by about 60% as compared to the
earlier SANYO STK407-000 series.

Features
• Series of pin compatible power amplifiers ranging from
20 W × 2 channels to 120 W × 2 channel (10%/1 kHz)
devices. The same printed circuit board can be used
depending on the output power grade.
• The pin arrangement is compatible with that of the 3-
channel STK402-200 series. This means that 3-channel
SANYO: SIP15
printed circuit boards can also be used for 2-channel
products.
• Miniature packages
— 15 W/ch to 40 W/ch (THD = 0.4%, f = 20 Hz to
20 kHz); 46.6 mm × 25.5 mm × 8.5 mm *
— 50 W/ch to 80 W/ch (THD = 0.4%, f = 20 Hz to
20 kHz); 59.2 mm × 31.0 mm × 8.5 mm *
*: Not including the pins.
• Output load impedance: RL = 6 Ω
• Allowable load shorted time: 0.3 seconds
• Supports the use of standby, muting, and load shorting
protection circuits.

Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.

SANYO Electric Co.,Ltd. Semiconductor Company


TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
92801RM (OT) No. 7047-1/6
STK402-070

Series Organization
These products are organized as a series based on their output capacity.
Type No.
Item
STK402-020 STK402-030 STK402-040 STK402-050 STK402-070 STK402-090 STK402-100 STK402-120
Output 1 (10%/1 kHz) 20 W + 20 W 30 W + 30 W 40 W + 40 W 45 W +45 W 60 W + 60 W 80 W + 80 W 100 W + 100 W 120 W + 120 W
Output 2 (0.4%/20 Hz to 20 kHz) 15 W + 15 W 20 W + 20 W 25 W + 25 W 30 W + 30 W 40 W + 40 W 50 W + 50 W 60 W + 60 W 80 W + 80 W
Maximum supply voltage
±30 V ±34 V ±38 V ±40 V ±50 V ±54 V ±57 V ±65 V
(No signal)
Maximum supply voltage
±28 V ±32 V ±36 V ±38 V ±44 V ±47 V ±50 V ±57 V
(6 Ω)
Recommended supply voltage
±19 V ±22 V ±25 V ±26.5 V ±30 V ±32 V ±35 V ±39 V
(6 Ω)
Package 46.6 mm × 25.5 mm × 8.5 mm 59.2 mm × 31.0 mm × 8.5 mm

Specifications
Maximum Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage (No signal) VCC max(0) ±50 V
Maximum supply voltage VCC max(1) RL = 6 Ω ±44 V
Thermal resistance θj-c Per power transistor 3.2 °C/W
Junction temperature Tj max 150 °C
Both the Tj max and the Tc max conditions must be met.
Operating IC substrate temperature Tc max 125 °C
Storage temperature Tstg –30 to +125 °C
Allowable load shorted time ts VCC = ±30.0 V, RL = 6 Ω, f = 50 Hz, PO = 40 W 0.3 s

Operating Characteristics at Ta = 25°C, RL = 6 Ω (noninductive load), Rg = 600 Ω, VG = 30 dB


Conditions*1 Ratings
Parameter Symbol Unit
VCC (V) f (Hz) PO (W) THD (%) min typ max
Output power PO (1) ±30.0 20 to 20 k 0.4 38 40
W
(continuous output) PO (2) ±30.0 1k 10 60
THD (1) ±30.0 20 to 20 k 1.0 VG = 30 dB 0.4
Total harmonic distortion %
THD (2) ±30.0 1k 5.0 VG = 30 dB 0.01
Frequency characteristics fL, fH ±30.0 1.0 +0 –3 dB 20 to 50 k Hz
Input impedance ri ±30.0 1k 1.0 55 kΩ
Output noise voltage *2 VNO ±36.0 Rg = 2.2 kΩ 1.2 mVrms
Quiescent current ICCO ±36.0 10 40 80 mA
Neutral voltage VN ±36.0 –70 0 +70 mV

Notes: 1. Unless otherwise noted, use a constant-voltage supply for the power supply used during inspection.
2. The output noise voltage values shown are peak values read with a VTVM. However, an AC stabilized (50 Hz) power supply should be used to
minimize the influence of AC primary side flicker noise on the reading.
Use the transformer power supply circuit stipulated in the figure below for output noise voltage measurement.
3. Use the transformer power supply circuit stipulated in the figure below for allowable load shorted time measurement.

DBA40C 10000µF
+VCC

500Ω

500Ω
--VCC
10000µF

Stipulated Transformer Power Supply (MG-200 equivalent)

No. 7047-2/6
STK402-070

Internal Equivalent Circuit

4
TR7 TR9
R1 R13

TR4 TR11
C1 R6 R8 C2

R3 TR5 TR12 R11


TR1 TR2 TR14 TR15
1

R4 TR8 R12
2 TR10

R5 R10
TR3 TR6 TR13 TR16

R2 D1 R7 R9 R14

9
13

SUB
5 12 7 6 10 11 14 15

Sample Application Circuit

Ch.1 Ch.2

SUB
Pre
Ch.1 Ch.1 Ch.1 Ch.1 Ch.2 Ch.2 Pre SUB Ch.2 Ch.2
IN NF +VCC BIAS +VE -VE +VCC -VCC +VE -VE -VCC GND NF IN
1 2 4 5 6 7 8 9 10 11 12 13 14 15
0.22Ω

0.22Ω

0.22Ω

0.22Ω
10kΩ

1kΩ 2.2µF 220pF 220pF 2.2µF 1kΩ


Ch.1 IN Ch.2 IN
3pF 3pF
1.8kΩ

1.8kΩ
470pF

470pF
56kΩ

56kΩ

56kΩ 56kΩ
100µF

100µF

100Ω 100Ω
10µF

10µF
33µF

33µF

3µH 3µH

Ch.1 OUT Ch.2 OUT


4.7Ω 0.1µF

0.1µF

4.7Ω 4.7Ω
4.7Ω

+VCC -VCC

No. 7047-3/6
STK402-070

Thermal Design Example

The thermal resistance, θc-a of the required heat sink for the power dissipation, Pd, within the hybrid IC is determined as
follows.

Condition 1: The IC substrate temperature, Tc, must not exceed 125°C.

Pd × θc – a + Ta < 125°C . . . . . . . . . (1)


Ta: Guaranteed ambient temperature for the end product.

Condition 2: The junction temperature, Tj, of each power transistor must not exceed 150°C.

Pd × θc – a + Pd/N × θj – c + Ta < 150°C . . . . . . . . . (2)


N: Number of power transistors
θc-a: Thermal resistance per power transistor

However, the power dissipation, Pd, for the power transistors shall be allocated equally among the N transistors.
The following inequalities results from solving equations (1) and (2) for θc-a.

θc – a < (125 – Ta) /Pd . . . . . . . . . . . . . . . . . . (1)’


θc – a < (150 – Ta) /Pd – θj – c/N . . . . . . . . . (2)’

Values that satisfy these two inequalities at the same time represent the required heat sink thermal resistance.
When the following specifications have been stipulated, the required heat sink thermal resistance can be determined from
formulas (1)’ and (2)’.

• Supply voltage — VCC


• Load resistance value — RL
• Guaranteed ambient temperature — Ta

[Example]
When the IC supply voltage, VCC, is ±30 V and RL is 6 Ω, the IC internal power dissipation, Pd, will be a maximum of
63 W for a continuous sine wave signal at 1 kHz, according to the Pd – PO characteristics.
For the music signals normally handled by audio amplifiers, a value of 1/8 PO max is generally used for Pd as an estimate
of the power dissipation based on this type of continuous signal. (Note that the factor used may differ depending on the
safety standards used.)
That is:

Pd = 42 W (When 1/8 PO max = 5 W)

The number of power transistors in the audio amplifier block of these hybrid ICs, N, is 4, and the thermal resistance per
transistor is 3.2°C/W. Therefore, the required heat sink thermal resistance for a guaranteed ambient temperature of 50°C
will be as follows.

From formula (1)’ θc – a < (125 – 50) /42


< 1.78
From formula (2)’ θc – a < (150 – 50) /42 – 3.2/4
< 1.58

Therefore, 1.58°C/W is the required heat sink thermal resistance.


Note that this thermal design example assumes the use of a constant-voltage power supply, and is therefore not a verified
design for any particular user's end product.

No. 7047-4/6
STK402-070

Pd — PO THD — PO
80 10
VCC=±30V 7 Tc=25°C
5
Total device power dissipation, Pd — W

RL=6Ω VCC=±30V

Total harmonic distortion, THD — %


70 3
f=1kHz 2 VG=30dB
60
VG=30dB 1.0
RL=6Ω
Rg=600Ω 7 Rg=600Ω
5
50
2ch drive 3
(same output rating) 2
40 0.1
7 20kH
5
30 3
2
20 0.01 z
7 1kH 20H
z
5
10 3
2
0 0.001
0.1 2 3 5 7 1.0 2 3 5 7 10 2 3 5 7 100 0.1 2 3 5 7 1.0 2 3 5 7 10 2 3 5 7 100
Output power per channel, PO / ch — W ITF02132 Output power, PO — W ITF02133
ICCO — PO PO — f
1.6 80
RL=6Ω Tc=25°C
Total current consumption, ICCO / ch — A

1.4 f=1kHz 70 VG=30dB


Rg=600Ω RL=6Ω, VCC=±30V, THD=10%
Rg=600Ω
1.2
1ch drive Output power, PO — W 60

RL=6Ω, VCC=±30V, THD=0.4%


1.0 50

0.8 40

0.6 30

0.4 20

0.2 10

0 0
0.1 2 3 5 7 1.0 2 3 5 7 10 2 3 5 7 100 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k
Output power per channel, PO / ch — W ITF02134 Frequency, f — Hz ITF02135
PO — VCC
100
Tc=25°C
90 f=1kHz
VG=30dB
80
RL=6Ω
Output power, PO — W

70 Rg=600Ω
2ch drive
60 0%
D =1
50 TH %
0.4
D=
40 TH
30

20

10

0
16 18 20 22 24 26 28 30 32 34 36
Supply voltage, VCC — V ITF02136

No. 7047-5/6
STK402-070

Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products (including technical data, services) described or contained
herein are controlled under any of applicable local export control laws and regulations, such products must
not be exported without obtaining the export license from the authorities concerned in accordance with the
above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification”
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.

This catalog provides information as of September, 2001. Specifications and information herein are
subject to change without notice.

PS No. 7047-6/6
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.

Potrebbero piacerti anche