Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Made in Italy
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non assunta alcuna responsabilit per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non pu essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilit sulluso o sullapplicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le prsent manuel ont t rdiges et contrles avec le plus grand
soin. Nous dclinons toutefois toute responsabilit en cas d'ventuelles inexactitudes. Tous droits
rservs. Ce document ne peut tre copi, photocopi ou reproduit, dans sa totalit ou partiellement,
sans le consentement pralable de D.T.S.
D.T.S. se rserve le droit d'apporter toutes modifications et amliorations esthtiques, fonctionnelles ou
de design, sans pravis, chacun de ses produits. D.T.S. dcline toute responsabilit sur l'utilisation ou
sur l'application des produits ou des circuits dcrits.
INDEX:
1- SYMBOLS
2- GENERAL WARNING
3- GENERAL WARRANTY CONDITION
4- TECHNICAL FEATURES
5- ACCESSORIES
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention
6.2 Prevention of electric shock
6.3 Protection against ultraviolet radiation
6.4 Safety
6.5 Level of protection against the penetration of solid and liquid objects
7- MOUNTING THE LAMP
7.1 Lamp alignment
8- VOLTAGE AND FREQUENCY
9- INSTALLATION
9.1 Safety cable
9.2 Protection against liquids
9.3 Movement
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature
10- MAINS CONNECTION
10.1 Protection
11- DMX SIGNAL CONNECTION
11.1 DMX Addresses
11.2 Selecting the DMX address
12- FIRMWARE UPDATING
13- DISPLAY FUNCTIONS
14- ERROR MESSAGES
15- HIDDEN MENU
15.1 Calibration mode
16- PAN & TILT SPEED
17- FANS SPEED
18- OPENING THE PROJECTOR HOUSING
19- REPLACING GOBOS
20- PERIODIC CLEANING
20.1 Lenses and reflectors
20.2 Fans and air passages
21- PERIODIC CONTROLS
22- DMX PROTOCOL
23- 8 MOTORS CONTROL CARD
24- 8 MOTORS SLAVE CONTROL CARD
25- PAN & TILT CARD
26- CABLES RESEND CARD
27- DISPLAY CARD
28- LAMP ON-OFF CONTROL CARD
29- ROTATING GOBO WHEEL
30- FIXED GOBO WHEEL
31- COLOUR WHEEL 1
4
4
4
5
7
8
9
10
10
11
12
13
14
17
18
19
20
21
22
23
38
39
40
41
42
43
1- SYMBOLS
Graphic symbols used on this manual
!
F
UV
2M
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important information
regarding safety during installation , use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or experienced
person.
Always disconnect the device from the mains before replacing the lamp.
The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.
The device must always be equipped with an efficient ground connection.
4- TECHNICAL FEATURES
The XR3000 SPOT CMY is one of the most powerful moving heads in the 1200W range.
The XR3000 SPOT CMY in fact delivers a massive 85.000 Lux at 5 m (10 beam angle), thanks to its
improved optical group and dichroic glass reflector, combined with a Philips MSR Gold 1200 Fastfit lamp
(95.000 Lumens).
The XR3000 SPOT CMY is particularly suitable for all professional applications, both mobile (concerts,
shows, tours, special events) and fixed (clubs and other venues), requiring a light with extremely high
luminous output and versatility of functions.
The XR3000 SPOT CMY is also the ideal light for a vast range of applications in which quiet operation is
a priority, thanks to its silent ventilation system and silent pan/tilt operation.
The XR3000 SPOT CMY incorporates motorized focus; motorized iris; linear zoom (10- 35); a
sophisticated CMY colour synthesis system with 3 palettes for linear insertion, plus a colour wheel (7
colours + open); 2 gobo wheels: one customizable rotating gobo wheel (7 gobos) and one customizable
fixed gobo wheel (8 gobos); frost filter (soft edge); 3-facet rotating prism; animation wheel rotating in
both directions.
The 16 bit Pan/Tilt mechanism features an exclusive Super Speed function, and a locking system with
recessed buttons. Access to every feature of the internal menu is simple and direct, thanks to the new
user interface featuring a LCD backlit graphic display (128 x 64).
XR3000 SPOT CMY
(Cod. 03.MS011.EB.L)
Electronic ballast 90-245V 50/60 Hz Black finish
Also available with white finish (RAL 9003) on demand
Lamp
Lamp: Philips MSR Gold 1200 Fastfit
Automatic switching ON of lamp in case of accidental switching OFF.
Lamp ON/OFF via DMX; Reset via DMX.
Optical group
85.000 Lux at 5 m (10 beam angle)
Dichroic glass reflector
Focus
Motorized focus
Iris
Motorized iris (16 bit)
Zoom
Motorized zoom (10- 35)
4- TECHNICAL FEATURES
Dimmer / shutter / strobo
Linear dimmer
Shutter
Strobe from 0,85 flash/sec to 10 flash/sec
Colours
CMY colour synthesis system + colour wheel (7 colours + open) with linear selection for perfect 2-colour
beams
Colour change with blackout sync; rainbow effect
Gobos
1 customizable rotating gobo wheel (7 gobos)
1 customizable fixed gobo wheel (8 gobos); extractable gobo holders
Gobo change with synchronized blackout
Gobo scrolling; Gobo shake
Effects
Indexable prism rotating in both directions (3-facet)
Frost filter (soft edge)
Animation wheel rotating in both directions
Pan / Tilt
Pan 540 (3,9 sec.); Tilt 270 (2,6 sec.); 16-bit resolution
Super Speed function; extremely smooth and precise movements even at the highest speeds
Pan / Tilt locking system with recessed buttons
Automatic Pan/Tilt repositioning in case of knocks
Interface
LCD backlit graphic display (128x64)
Connections
4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik
POWERCONN connector by Neutrik
Power supply
Electronic ballast: 90 - 260 V (50/60 Hz)
Power consumption: 1400 W
Power saving mode (the lamp dims to 50% six seconds after shutter closure)
Standard accessories
2 x C GQuick clamps with fastlock connection
Thermal
Operating ambient temperature: -10 / 40
Weight
46,5 Kg
4- TECHNICAL FEATURES
Dimensions
Unit Dimensions (LxWxH)
568x510x826mm
Weight: 46,5 Kg
568mm
510mm
826mm
636mm
270
5- ACCESSORIES
459mm
As standard
1 x MSR Gold 1200 Fastfit lamp
1 x POWERCONN male cable connector (cod. 0520P014)
1 x XLR 5 Pins male cable connector (cod. 0508B028)
1 x XLR 5 Pins female cable connector (cod. 0508B027)
2 x C Clamp GQUICK with Fast Lock connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
Users manual
UV
-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
6.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
6.5 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid objects is IP 20.
For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:
Raincover for XR3000 base (top) (cod. 03.MA009)
Raincover for XR3000 base (bottom) (cod. 03.MA010)
Photo 1
Photo 2
Photo 3
Photo 4
Photo 5
Normal
Hot Spot
1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface
no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto
the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the 3 adjusters X, Y and
Z (photo 5) until you achieve a uniform flat field.
When the lamp is correctly optimized, you will have an evenly projected light beam, with no shadows or
zones wich are brighter than others.
10
9- INSTALLATION
XR3000 SPOT CMY may be either floor or ceiling mounted.
For floor mounting installations, the XR3000 SPOT CMY is supplied with four rubber mounting feet on
the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to
move or shake whilst the XR3000 SPOT CMY is moving.
Eight 1/4 turn Fast Locks connections placed in the base of the unit allow to fix the XR3000 SPOT CMY in
any position, by using the two Fast Lock C clamps provided in the box.
.
240 mm
107 mm
!
9.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
11
9.3- Movement
The projector has a maximum movement of 540 for Pan and 270 for Tilt. DO NOT place any
obstructions in the path of the projector's movement.
270
!
WARNING
Do not place any object in the path
of the projectors movement
540
F
Minimum distance from the object being illuminated is 2 MT.
2M
10.1- Protection
Electronic ballast
90-260V 50 / 60Hz
The use of a thermal magnetic circuit breaker is recommended for each XR3000 SPOT CMY.
A good earth connection is essential for the correct operation of the projector.
12
1=GND
2=DATA3=DATA+
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
5
2
3
OUT
PIN 3
120 ohm
PIN 2
13
11.1-DMX Addresses
XR3000 SPOT CMY can be controlled with 30 (default) or 22 DMX channels.
If you want to use the unit in 30 channels mode (default), set the following addresses on the mixer:
Projector 1
Projector 2
A001
A031
Projector 3
..
projector 6
A061
A.
A151
12 FIRMWARE UPDATING
Warning:
This procedure require a base knolewge of computer applications and Windows
Hyperterminal program. Please refer to an authorised D.T.S. service centre.
To update the software version of the XR3000 SPOT CMY you need:
D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).
USB-DMX Driver for the D.T.S. RED BOX interface .
(The driver and the installation procedure are available in our web site www.dts-lighting.it)
Updating the software version.
Please follow the procedure below to perform the update:
1.
2.
3.
4.
Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.
Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
Download the new software version into the unit by using Windows Hyperterminal program.
It will be possible to download the software from the reserved area of D.T.S. web site:
www.dts-lighting.it.
14
DISPLAY
DMX OUT
DMX IN
DMX IN
DMX OUT
UP
MENU
ENTER
MAINS
Electronic ballast
90-260V 50 / 60Hz
DOWN
DISPLAY FUNCTIONS
The XR3000 SPOT CMY display panel shows all the available functions . Using these functions, it is
possible to change some of the parameters and add some functions. Changing the D.T.S. setting
can vary the functions of the unit so that it does not respond to the DMX 512 used to control it.
Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol
shows which key has to be pushed to obtain the desired function.
Menu
Up-Down
Pan Direction
ENTER
Up-Down
PAN DIRECTION
This menu allows to set the Pan
movement.
Normal or Reversed
PAN DIRECTION
Up-Down
Tilt Direction
ENTER
Up-Down
TILT DIRECTION
This menu allows to set the Pan
movement.
Normal or Reversed
Up-Down
ENTER
ENTER
UP
TILT DIRECTION
NORMAL
MENU ENTER DOWN
Menu
ENTER
NORMAL
MENU ENTER DOWN
Menu
ENTER
Up-Down
UP
4
MENU ENTER DOWN
UP
15
Up-Down
Display
ENTER
Up-Down
Display Flip
ON THE GROUND (Default)
SUSPENDED
DISPLAY
FLIP
Display Flip:
Reverses display's reading depending on the
mounting position
(On the ground or suspended).
ENTER
ON THE GROUND
MENU ENTER DOWN
Display Standby:
To turn off the display (after 5 seconds)
Or leave it always on.
UP
Display Standby
OFF = Display Standby disabled
(Default)
ON = Display goes OFF after 5
seconds
DISPLAY
STANDBY
FLIP
Display Contrast:
Display contrast regulation (1-16)
OFF
MENU ENTER DOWN
ENTER
UP
Display Contrast
1-16 (Default = 8)
DISPLAY
ENTER
CONTRAST
FLIP
8
MENU ENTER DOWN
Menu
Up-Down
DMX Mode
ENTER
Up-Down
DMX MODE
To select DMX mode :
30 channels or 22 channels
DMX MODE
30 channels
MENU ENTER DOWN
Menu
Up-Down
Lamp
UP
ENTER
Up-Down
LAMP
Lamp always ON, always OFF,
lamp ON-OFF selectable via DMX
And lamp life time reset
LAMP
ADJUST
FLIP
Menu
Up-Down
Reset
RESET
Reset via DMX ENABLED / DISABLED
and unit reset
ENTER
Up-Down
ENTER
UP
RESET
BY DMX
ENABLED
MENU ENTER DOWN
ENTER
UP
LAMP
ENTER
UP
BY
DMX
FLIP
ADJUST
To adjust the lamp with no mixer
connected.
Its possible to set the parameters for
PAN-TILT and ZOOM
DMX mode
30 channels (Default)
22 channels
UP
ENTER
16
Up-Down
Fan Speed
ENTER
Up-Down
FAN SPEED
Fan Speed control
FAN SPEED
Up-Down
Auto Focus
ENTER
Up-Down
AUTO FUCOS
Automatic focusing
Up-Down
Gobo Rotation
ENTER
Up-Down
CMY Blackout
ENTER
Up-Down
CMY BLACKOUT
CMY filters blades inserted at 100% if the dimmer
remain closed for more than 5 seconds.
By activating this function, it will be possible to
reduce substantially any visible light reflection
coming out from the front lens when dimmer is
closed.
Menu
Up-Down
System info
ENTER
Up-Down
SYSTEM INFO
Lamp life time, lamp strikes, unit life time, 8
motors card software version, Pan&Tilt card
software version and unit model
Up-Down
Reserved
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
System Reboot
(Code = 100)
ENTER
ENTER
OFF
ENTER
UP
CMY BLACKOUT
ON
MENU ENTER DOWN
UP
SYSTEM INFO
LAMP LIFE:0000H
STRIKE:001
UNIT LIFE: 0010H
8M R.47
PT R.22
MODEL: XR 3000 SPOT CMY
Menu
ON
OFF = (Default)
UP
GOBO ROTATION
Up-Down
ENTER
OFF
GOBO ROTATION
Gobo rotation control the Rotating speed of gobo
Menu
ON
OFF = (Default)
UP
AUTO FOCUS
Menu
ENTER
12
MENU ENTER DOWN
Menu
Up-Down
SYSTEM INFO
Lamp life time, lamp strikes, unit life
time, 8 motors card software
version, Pan&Tilt card software
version and unit model
ENTER
UP
RESERVED
ENTER
ENTER CODE
000
MENU ENTER DOWN
UP
PAN LOCK
NO
UP
17
Menu
Up-Down
Default
ENTER
Default
To restore main settings
DEFAULT
Up-Down
DEFAULT
To restore main settings
ENTER
UP
DEFAULT
RESTORE MAIN SETTINGS
SURE?
PRESS ENTER TO CONFORM
PRESS MENU TO CANCEL
UP
ERROR
ERROR
ERROR
COLOUR WHEEL
CYAN
MAGENTA
YELLOW
UP
COLOUR WHEEL
POSITION ERROR
UP
UP
MAGENTA POSITION
ERROR
UP
YELLOW POSITION
ERROR
ERROR
ERROR
ERROR
ERROR
PAN
TILT
INTERNAL BUS
DMX ADDRESS
UP
PAN REPOSITIONING
ENCODER ERROR
UP
TILT REPOSITIONING
ENCODER ERROR
UP
COMMUNICATION
PROBLEM BETWEEN 8
MOTORS CARD AND
PAN&TILT CARD
UP
DMX ADDRESS
ERROR
ERROR
ERROR
ERROR
ERROR
GOBO
GOBO INDEX
FIXED GOBO
ANIMATION
UP
GOBO POSITION
ERROR
UP
UP
ANIMATION WHEEL
ERROR
UP
18
ERROR
ERROR
ERROR
IRIS
EFFECT
FOCUS
UP
IRIS ERROR
FOCUS ERROR
ERROR
ERROR
ZOOM
DIFFUSER
UP
UP
UP
DIFFUSER ERROR
ZOOM ERROR
CALIBRATION
DEFAULT CAL
FANS SPEED
MOTORS ALIGNMENT
PAN
134
MENU ENTER DOWN
UP
ELECTRONIC
CALIBRATION OF THE
MOTORS
UP
RESET EEPROM.
RESET ALL SETTINGS
TO 128 VALUE
EXIT TO MAIN
100=100%
10
MENU ENTER DOWN
UP
UP
UP
UP
19
15.1 Calibration
CALIBRATION
CALIBRATION
CALIBRATION
MOTORS ALIGNMENT
MOTORS ALIGNMENT
MOTORS ALIGNMENT
PAN
TILT
SHUTTER
134
167
145
UP
PAN ALIGNMENT
To align Pan position
UP
TILT ALIGNMENT
To align Tilt position
UP
SHUTTER ALIGNMENT
To align Shutter blades
CALIBRATION
CALIBRATION
CALIBRATION
MOTORS ALIGNMENT
MOTORS ALIGNMENT
MOTORS ALIGNMENT
COLOUR WHEEL
CYAN ZERO
CYAN PATH
151
162
134
UP
UP
UP
CALIBRATION
CALIBRATION
CALIBRATION
MOTORS ALIGNMENT
MOTORS ALIGNMENT
MOTORS ALIGNMENT
MAGENTA ZERO
MAGENTA PATH
YELLOW ZERO
167
151
141
UP
UP
UP
CALIBRATION
CALIBRATION
CALIBRATION
MOTORS ALIGNMENT
MOTORS ALIGNMENT
MOTORS ALIGNMENT
YELLOW PATH
GOBO
GOBO INDEX
121
151
141
UP
UP
UP
CALIBRATION
CALIBRATION
CALIBRATION
MOTORS ALIGNMENT
MOTORS ALIGNMENT
MOTORS ALIGNMENT
FIXED GOBO
ANIMATION
IRIS
151
151
85
UP
UP
IRIS ALIGNMENT
To align IRIS
UP
20
Calibration mode
CALIBRATION
CALIBRATION
CALIBRATION
MOTORS ALIGNMENT
MOTORS ALIGNMENT
MOTORS ALIGNMENT
EFFECTS
FOCUS
ZOOM
85
151
151
UP
FOCUS ALIGNMENT
To alignFOCUS
EFFECTS ALIGNMENT
To align EFFECTS
UP
UP
ZOOM ALIGNMENT
To align ZOOM
CALIBRATION
MOTORS ALIGNMENT
DIFFUSER
85
MENU ENTER DOWN
UP
DIFFUSER ALIGNMENT
To align DIFFUSER
21
Photo 1
Photo 2
Max thickness
ED
ID
XR3000 SPOT CMY uses a mechanical system which allows the fixture's gobos to be removed without
the use of special tools. Replacement gobos should be made of either heat resistant glass or metal.
An ever-increasing range of gobos is available from your D.T.S. sales network.
Gobo dimensions are as follows:
external (ED) = 27.9 mm
of image with defined edge (ID) = 24 mm
thickness = from 0.2 to 4 mm (see catalogue)
4 mm
Coated side
Coated side
When an object is held up the coated side of the glass gobo there
is no space between the object and its reflection.
Uncoated side
When an object is held up the uncoated side of the glass gobo
there is a space between the object and its reflection.
Uncoated side
22
Photo 2
Photo 1
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will
help to avoid the danger of the lamp exploding.
XR3000 SPOT CMY lamp lifespan is about 750 hours, then it is necessary to replace it.
Mechanical parts
Periodically check all mechanical parts,gears, guides, belts, etc.for wear and tear, replacing them if
necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors,
refastening if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XR3000 SPOT CMY
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.
UV
23
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX range
Value
000-010
011-025
026-127
128-247
248-255
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Silent Mode
24
DMX CHANNEL
DMX range
Value
Parameter: DIMMER
Mid point
DMX value
Move
range
(degrees)
Mode
Option
000-007
008-255
DMX CHANNEL
DMX range
Value
Black-out
Proportional dimmer
7
Parameter: SHUTTER
Mid point
DMX value
Move
range
(degrees)
Mode
Option
000-019
020-039
040-059
060-079
080-089
090-099
100-109
110-119
120-129
130-139
140-149
150-159
160-169
170-179
180-189
190-199
200-209
210-219
220-227
228-233
234-255
DMX CHANNEL
DMX range
Value
000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255
Function
Function
Black-out
Open
Black-out
Random Strobe
Strobe speed 1 min. (0,85 Hz)
Strobe speed 2 (1,4 Hz)
Strobe speed 3 (2 HZ)
Strobe speed 4 (3,75 Hz)
Strobe speed 5 (5 Hz)
Strobe speed 6 max. (6,75 Hz)
Pulse open speed 1 min.
Pulse open speed 2
Pulse open speed 3
Pulse open speed 4 max.
Pulse closed speed 1 min.
Pulse closed speed 2
Pulse closed speed 3
Pulse closed speed 4 max.
Colour and Gobo in black-out
Pan and Tilt in black-out
Open
Parameter: COLOUR
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Colour 1
Colour 2
Colour 3
Colour 4
Colour 5
Colour 6
Colour 7
Colour 8
25
DMX CHANNEL
DMX range
Value
Parameter: COLOUR
Mid point
DMX value
Move
range
Mode
Option
Function
(degrees)
IF CHANNEL 9 = HALF COLOUR (DMX range value 64 - 127)
000-027
028-055
056-083
084-111
112-139
140-167
168-195
196-223
224-255
Colour 1
Bicolour 1/ 2
Bicolour 2/ 3
Bicolour 3/ 4
Bicolour 4/ 5
Bicolour 5/ 6
Bicolour 6/ 7
Bicolour 7/ 8
Bicolour 8/ 1
000-010
011-255
000-009
010-127
128-137
138-255
DMX CHANNEL
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Full Colour
Half Colour
Proportional Colour
Propotional Rainbow
000-063
064-127
128-191
192-255
DMX CHANNEL
10
DMX range
Value
Mid point
DMX value
Parameter: CYAN
Move
range
(degrees)
Mode
Option
Function
Propotional colour
000-255
DMX CHANNEL
11
DMX range
Value
Mid point
DMX value
000-255
Function
Parameter: MAGENTA
Move
range
(degrees)
Mode
Option
Function
Propotional colour
26
DMX CHANNEL
12
DMX range
Value
Mid point
DMX value
Parameter: YELLOW
Move
range
(degrees)
Mode
Option
Propotional colour
000-255
DMX CHANNEL
DMX range
Value
13
Mid point
DMX value
Move
range
(degrees)
Mode
DMX range
Value
000-009
010-014
015-019
020-024
025-029
030-034
035-039
040-044
045-049
050-054
055-059
060-064
065-069
070-074
075-079
080-084
085-089
090-094
095-099
100-104
105-109
110-114
115-121
122-128
129-135
136-142
143-149
150-156
157-163
164-170
Option
Function
No function
Variable speed from max to min
000-007
008-255
DMX CHANNEL
Function
14
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
No function
Macro1
Macro2
Macro3
Macro4
Macro5
Macro6
Macro7
Macro8
Macro9
Macro10
Macro11
Macro12
Macro13
Macro14
Macro15
Macro16
Macro17
Macro18
Macro19
Macro20
Macro21
Macro rainbow wait=0
Macro rainbow wait=2
Macro rainbow wait=3
Macro rainbow wait=4
Macro rainbow wait=5
Macro rainbow wait=6
Macro rainbow wait=7
Macro rainbow wait=8
27
DMX CHANNEL
DMX range
Value
14
Mid point
DMX value
Move
range
(degrees)
Mode
DMX range
Value
15
Parameter: GOBO 1
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Speed rotation 1 min.
Speed rotation 2
Speed rotation 3
Speed rotation 4
Speed rotation 5
Speed rotation 6
Speed rotation 7
Speed rotation 8 max
000-025
026-051
052-077
078-103
104-129
130-155
156-181
182-207
208-213
214-219
220-225
226-231
232-237
238-243
244-249
250-255
DMX CHANNEL
16
DMX range
Value
Mid point
DMX value
000-127
128-255
Function
171-177
178-185
186-192
193-199
200-206
207-213
214-220
221-227
228-234
235-241
242-248
249-255
DMX CHANNEL
Option
Move
range
(degrees)
Mode
Option
Function
Gobo rotation mode
Gobo index mode
28
DMX CHANNEL
17
DMX range
Value
Mid point
DMX value
Move
range
Mode
Option
Function
(degrees)
IF CHANNEL 16 = Gobo Rotation Mode (Dmx range value 0 - 127)
Stop
CCW Rot. Prop. Speed Max to Min
Stop
CW Rot. Prop. Speed Min to Max
IF CHANNEL 16 = Gobo Index Mode (Dmx range value 128 - 255)
Gobo index Coarse
000-009
010-127
128-137
138-255
000-255
DMX CHANNEL
DMX range
Value
18
Mid point
DMX value
Move
range
(degrees)
Mode
Option
000-255
DMX CHANNEL
DMX range
Value
000-009
010-022
023-035
036-048
049-061
062-074
075-087
088-100
101-113
114-126
127-138
139-151
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
Function
19
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Stop
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
Gobo Shake L-R Speed 9 Max
29
DMX CHANNEL
DMX range
Value
20
Mid point
DMX value
Move
range
(degrees)
Mode
Option
000-022
023-045
046-068
069-091
092-114
115-137
138-160
161-183
184-207
208-213
214-219
220-225
226-231
232-237
238-243
244-255
DMX CHANNEL
DMX range
Value
000-009
010-022
023-035
036-048
049-061
062-074
075-087
088-100
101-113
114-126
127-138
139-151
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
Function
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Speed rotation 1 min
Speed rotation 2
Speed rotation 3
Speed rotation 4
Speed rotation 5
Speed rotation 6
Speed rotation 7 max
21
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Stop
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
Gobo Shake L-R Speed 9 Max
30
DMX CHANNEL
22
DMX range
Value
Mid point
DMX value
Parameter: ANIMATION
Move
range
(degrees)
Mode
Option
No function
Linear animation position
000-009
010-255
DMX CHANNEL
DMX range
Value
23
Mid point
DMX value
Move
range
(degrees)
Mode
DMX range
Value
Option
24
Parameter: IRIS
Mid point
DMX value
Move
range
(degrees)
Mode
Option
DMX range
Value
25
Mid point
DMX value
DMX range
Value
000-050
051-085
086-171
172-255
Move
range
(degrees)
Mode
Option
Function
No effect
Iris pulse at different speed from Min to Max
Iris pulse with flash closing from Min to Max
Iris pulse with flash opening from Min to Max
000-009
010-063
064-117
118-171
172-213
214-255
DMX CHANNEL
Function
Open
Linear Iris from Open to Closed
Closed
000-009
010-246
247-255
DMX CHANNEL
Function
Stop
CCW rotation from fast to slow
Stop
CW rotation from fast to slow
000-009
010-127
128-137
138-255
DMX CHANNEL
Function
Iris pulse with flash closing combined with zoom from Min to Max
Iris pulse with flash opening combined with zoom from Min to Max
26
Parameter: EFFECTS
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
No effect
Diffuser
Prism
Frost
31
DMX CHANNEL
DMX range
Value
27
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Stop
CCW Rotation from fast to slow
Stop
CW Rotation from slow to fast
000-009
010-127
128-143
144-255
DMX CHANNEL
28
DMX range
Value
Mid point
DMX value
Parameter: FOCUS
Move
range
(degrees)
Mode
Option
DMX range
Value
Linear focus ( 1m to 29
Parameter: ZOOM
Mid point
DMX value
Move
range
(degrees)
Mode
Option
000-255
Function
Linear zoom from 8 to 30
DMX CHANNEL
30
DMX range
Value
Mid point
DMX value
000-009
010-060
061-129
130-179
180-200
201-239
240-255
Function
O
O
000-255
DMX CHANNEL
Function
Parameter: RESET
Move
range
(degrees)
Mode
Option
Function
No Effect
Lamp OFF (activ.after 3 seconds)
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
Internal motor reset
Total Reset
32
22 CHANNELS MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX range
Value
000-010
011-025
026-127
128-247
248-255
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Silent Mode
33
DMX CHANNEL
DMX range
Value
Parameter: DIMMER
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Black-out
Proportional dimmer
000-007
008-255
DMX CHANNEL
DMX range
Value
Parameter: SHUTTER
Mid point
DMX value
Move
range
(degrees)
Mode
Option
0-19
20-39
40-59
60-79
80-89
90-99
100-109
110 -119
120-129
130-139
140-149
150-159
160-169
170-179
180-189
190-199
200-209
210-219
220-227
228-233
234-255
DMX CHANNEL
DMX range
Value
000-011
012-023
024-035
036-047
048-059
060-071
072-083
084-095
096-107
108-119
120-131
132-143
Function
Function
Black-out
Open
Black-out
Random Strobe
Strobe speed 1 min. (0,85 Hz)
Strobe speed 2 (1,4 Hz)
Strobe speed 3 (2 HZ)
Strobe speed 4 (3,75 Hz)
Strobe speed 5 (5 Hz)
Strobe speed 6 max. (6,75 Hz)
Pulse open speed 1 min.
Pulse open speed 2
Pulse open speed 3
Pulse open speed 4 max.
Pulse closed speed 1 min.
Pulse closed speed 2
Pulse closed speed 3
Pulse closed speed 4 max.
Colour and Gobo in black-out
Pan and Tilt in black-out
Open
Parameter: COLOUR 1
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Colour 1
Colour 1-2
Colour 2
Colour 2-3
Colour 3
Colour 3-4
Colour 4
Colour 4-5
Colour 5
Colour 5-6
Colour 6
Colour 6-7
34
DMX CHANNEL
DMX range
Value
Parameter: COLOR
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Colour 7
Colour 7-8
Colour 8
Colour 8-1
CW rotation speed 9 max.
CW rotation speed 8
CW rotat ion speed 7
CW rotation speed 6
CW rotation speed 5
CW rotation speed 4
CW rotation speed 3
CW rotation speed 2
CW rotation speed 1 min.
Stop
CCW rotation speed 1 min.
CCW rotation speed 2
CCW rotation speed 3
CCW rotation speed 4
CCW rotation speed 5
CCW rotation speed 6
CCW rotation speed 7
CCW rotation speed 8
CCW rotation speed 9 max.
144-155
156-167
168-179
180-197
198-200
201-203
204-206
207-209
210-212
213-215
216-218
219-221
222-224
225-228
229-231
232-234
235-237
238-240
241-243
244246
247-249
250-252
253-255
DMX CHANNEL
DMX range
Value
Parameter: CYAN
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Propotional colour
000-255
DMX CHANNEL
10
DMX range
Value
Mid point
DMX value
Parameter: MAGENTA
Move
range
(degrees)
Mode
Option
Function
Propotional colour
000-255
DMX CHANNEL
11
DMX range
Value
Mid point
DMX value
000-255
Function
Parameter: YELLOW
Move
range
(degrees)
Mode
Option
Function
Propotional colour
35
DMX CHANNEL
DMX range
Value
12
Parameter: GOBO
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Speed rotation 1 min.
Speed rotation 2
Speed rotation 3
Speed rotation 4
Speed rotation 5
Speed rotation 6
Speed rotation 7
Speed rotation 8 max
000-025
026-051
052-077
078-103
104-129
130-155
156-181
182-207
208-213
214-219
220-225
226-231
232-237
238-243
244-249
250-255
DMX CHANNEL
13
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode
DMX range
Value
000-022
023-045
046-068
069-091
092-114
115-037
138-160
161-183
184-207
208-213
214-219
220-225
226-231
232-237
238-243
244-255
Option
Function
Stop
CCW Rot. Prop. Speed Max to Min
Stop
CW Rot. Prop. Speed Min to Max
000-127
128-180
181-202
203-255
DMX CHANNEL
Function
14
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Speed rotation 1 min
Speed rotation 2
Speed rotation 3
Speed rotation 4
Speed rotation 5
Speed rotation 6
Speed rotation 7 max
36
DMX CHANNEL
15
DMX range
Value
Mid point
DMX value
Parameter: ANIMATION
Move
range
(degrees)
Mode
Option
No function
Linear animation position
000-009
010-255
DMX CHANNEL
DMX range
Value
16
Mid point
DMX value
Move
range
(degrees)
Mode
Option
DMX range
Value
17
Parameter: IRIS
Mid point
DMX value
DMX range
Value
Move
range
(degrees)
Mode
Option
Iris pulse with flash closing combined with zoom from Min to Max
Iris pulse with flash opening combined with zoom from Min to Max
18
Parameter: EFFECTS
Mid point
DMX value
Move
range
(degrees)
Mode
Option
DMX range
Value
000-009
010-127
128-143
144-255
Function
No effect
Diffuser
Prism
Frost
000-050
051-085
086-171
172-255
DMX CHANNEL
Function
Open
Linear Iris from Open to Closed
Closed
Iris pulse at different speed from Min to Max
Iris pulse with flash closing from Min to Max
Iris pulse with flash opening from Min to Max
000-009
010-124
125-132
133-159
160-186
187-213
214-234
235-255
DMX CHANNEL
Function
Stop
CCW rotation from fast to slow
Stop
CW rotation from fast to slow
000-009
010-127
128-137
138-255
DMX CHANNEL
Function
19
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
Stop
CCW Rotation from fast to slow
Stop
CW Rotation from slow to fast
37
DMX CHANNEL
20
DMX range
Value
Mid point
DMX value
Parameter: FOCUS
Move
range
(degrees)
Mode
Option
DMX CHANNEL
DMX range
Value
Linear focus ( 1m to 21
Parameter: ZOOM
Mid point
DMX value
Move
range
(degrees)
Mode
Option
000-255
Function
Linear zoom from 8 to 30
DMX CHANNEL
22
DMX range
Value
Mid point
DMX value
000-009
010-060
061-129
130-179
180-200
201-239
240-255
O
O
000-255
Function
Move
range
(degrees)
Mode
Option
Function
No Effect
Lamp OFF (activ.after 3 seconds)
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
Internal motor reset
Total Reset
38
J7 Magnetic Sensors
Connector
Line 1 Brown
Line 2 Orange
GND
ORANGE
BROWN
VCC
J26 to 6 Motors
Control card
Strobe
(YELLOW)
Animation
(PINK)
J1 Internal DATA
Communication
Connector
From J8 Pan & Tilt
card
+
Colour
30 VDC
(GREY)
Magenta
(LIGHT BLUE)
Cyan
(Gold)
Yellow
(LIGHT BLUE)
Fans
Fans
39
Rot Animation
(YELLOW LINE)
Diffuser
(VIOLET LINE)
Iris
(RED)
J1 from 8
Motors
Control card
Effect rotation
(DARK ORANGE)
+
Effects
(LIGHT ORANGE)
30 VDC
Gobo rotation
(BROWN)
Zoom
(YELLOW)
Focus
(VIOLET)
40
TILT
(BROWN)
GND
(BLACK)
30 VDC
(RED)
FAN
(WHITE)
ENCODER PAN
(RED)
MOTOR TILT
(BROWN)
DATA 2
(LIGHT GREEN)
DATA 1
(VIOLET)
ENCODER TILT
(ORANGE)
TO J2
LAMP
ON-OFF
CARD
TO J1
DISPLAY CARD
(WHITE)
TO J1
8 MOTORS CARD
(GREEN)
DMX INPUT
(WHITE)
ENCODER TILT
(ORANGE)
27-DISPLAY CARD
FROM J16
PAN&TILT
CARD
J2
J4
J3
TO J9
ELECTRONIC
BALLAST
41
4
5
3
2
3
GOBO 1 DICRO
0516G032.01
GOBO 4 DICRO
0516G032.10
GOBO 2 DICRO
0516G032.08
GOBO 5 DICRO
0516G032.11
GOBO 3 DICRO
0516G032.12
GOBO 6 DICRO
GOBO 7 DICRO
0516G032.03
0516G032.05
42
7
6
8
4
1
2
GOBO 1 DICRO
0516G032.06
GOBO 5 GLASS
0516G032.14
GOBO 2 DICRO
0516G032.04
GOBO 6 DICRO
0516G032.09
3
GOBO 3 METAL
0516G032.15.M.58
GOBO 4 DICRO
0516G032.07
GOBO 7 DICRO
GOBO 8 DICRO
0516G032.13
0516G032.02
43
2
1
7
6
COL 2
COL 3
COL 4
0507C046.D10
WOOD SW460
0507C051.D10
ORANGE LW590
0507C042.D10
GREEN WB5055
COL 1
0507K004.D10
CONV.FILTER HOT
TC3256
COL 5
0507C047.D10
RED LW 640
COL 6
0507C041.D10
DARK BLUE SW490
COL 7
0507C053.D10
AMBER LW550
44
NOTES
XR3000
SPOT CMY
ARC 1200
45
NOTES
46
NOTES
XR3000
SPOT CMY
ARC 1200
47
NOTES
XR3000
SPOT CMY
ARC 1200
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its
products without prior notice. D.T.S. assumes no responsibility for the use or application of the
products or circuits described herein.
MADE IN ITALY
*0517I147*
0517I147
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111
info@dts-lighting.it www.dts-lighting.it