Sei sulla pagina 1di 24

CAPACITORS & POWER QUALITY MANAGEMENT

Capacitors
Technical Data
Overall Dimensions & Ordering Data

12

Detuned Filters
Overall Dimensions & Ordering Data

Page
12/1-12/3
12/4-12/15

APFC Panels
Technical Data
Overall Dimensions & Ordering Data

Page
12/20-12/22

www.LNTEBG.com

Page
12/16 - 12/17
12/18-12/19

TECHNICAL DATA
Series

26 D

19 M

Type

MPP-D

MPP-S

Capacitors for Agricultural use

MPP-S Capacitor unit

Standards

IS13340-1993

IS13340-1993 / IS13341-1992 /
IEC 831-1 (1996-11) & IEC 831-2 (1995-12)

Rated voltage

415/440 V (Other ratings on request)

415/440 V (Other ratings on request)

Overvoltage

As per clause of IS13340-1993

Un Continuous
Un + 10% (up to 12 hours daily)
Un + 15% (up to 30 minutes daily)
Un + 20% (up to 5 minutes daily)
Un + 30% (up to 1 minute)
Any overvoltage>1.15 Un shall not occur
more than 200 times in the Capacitors life
As per clause 20.1 of IEC

Overcurrent

As per clause of IS13340-1993

1.5 In at 1.15 Cn combined with


overvoltage & presence of harmonics, as
per clause, 21 of IEC 831.

Frequency (Hz)

50 / 60

50 / 60

No of phases

Three

Single (or) Three

Capacitance tolerance

-5% to +10%

-5% to 15%

Test voltage, terminal / terminal

1.5 . Un

2.15 . Un

Test voltage, terminal / case

2.5 kV AC

3.6 kV AC

Peak transient overcurrent

100 x In

100 x In

Losses

Total

0.5 W / kVAr

0.5 W / kVAr

Dielectric

0.2 W / kVAr

0.2 W / kVAr

(Insulation level)

Degree of protection

IP 21 (with connecting cable)

IP 31

Ambient temperature category

-25 / D (Maximum 55 deg C)

-25 / D (Maximum 55 deg C)

Maximum permissible altitude

2000m above mean sea level

2000m above mean sea level

Mounting position

Wall mounting

Vertical with terminal upwards

Safety features

Self healing

Self healing

Polyurethane Resin encapsulation

Pressure Sensitive Disconnector (PSD)

M.S. Sheet Metal

M.S. Sheet Metal

Container type
Finish

Polyester Pain Coated

Polyester Pain Coated

Dielectric

Bi-axially oriented Polypropylene Film

Bi-axially oriented Polypropylene Film

Impregnant

Resin

Non-PCB bio-degradable impregnant

Discharge Device

Discharge Resistor

Discharge Resistor

Electrodes

Special vaccuum deposited metal

Special vaccuum deposited metal

alloy with re-inforced edge.

alloy with re-inforced edge.

www.LNTEBG.com

12

12/1

TECHNICAL DATA

12

Series

80 M

61 M

Type

MPP-H

MD-XL

MPP-H Capacitor unit

MD-XL Capacitor unit

Standards

IS 13340-1993 / IS 13341-1992 /
IEC 831-1 (1996-11) & IEC 831-2 (1995-12)

IS 13340-1993 / IS 13341-1992 /
IEC 831-1 (1996-11) & IEC 831-2 (1995-12)

Rated voltage

415/440 V (Other ratings on request)

415/440 V (Other ratings on request)

Overvoltage

Un Continuous
Un + 15% (up to 12 hours daily)
Un + 20% (up to 30 minutes daily)
Un + 25% (up to 5 minutes daily)
Un + 30% (up to 1 minute)
Any overvoltage>1.15 Un shall not occur
more than 200 times in the Capacitors life
As per clause 20.1 of IEC

Un Continuous
Un + 15% (up to 12 hours daily)
Un + 20% (up to 30 minutes daily)
Un + 25% (up to 5 minutes daily)
Un + 30% (up to 1 minute)
As per IEC clause 20.1

Overcurrent

1.8 In at 1.15 Cn combined with


overvoltage & presence of harmonics, as
per IEC clause 21.

2 In at 1.15 Cn combined with


overvoltage & presence of
harmonics, as per IEC clause 21.

Frequency (Hz)

50 / 60

50 / 60

No of phases

Single (or) Three

Single (or) Three

Capacitance tolerance

-5% to 15%

-5% to 15%

Test voltage, terminal / terminal

2.15 . Un

2.15 . Un

Test voltage, terminal / case

3.6 kV AC

3.6 kV AC

Peak transient overcurrent

200 x In

200 x In

Losses

0.5 W / kVAr
0.2 W / kVAr

0.5 W / kVAr
0.2 W / kVAr

Total
Dielectric

Degree of protection

IP 31

IP 31

Ambient temperature category

-25 / D (Maximum 55 deg C)

-25 / D (Maximum 55 deg C)

Maximum permissible altitude

2000m above mean sea level

2000m above mean sea level

Mounting position

Vertical with terminal upwards

Vertical with terminal upwards

Safety features

Self healing with PSD


Pressure Sensitive Disconnector

Self healing with PSD


Pressure Sensitive Disconnector

Container type

M.S. Sheet Metal

M.S. Sheet Metal

Finish

Polyester Pain Coated

Polyester Pain Coated

Dielectric

Bi-axially oriented Polypropylene Film

Combination of Capacitor tissue


paper and bi-axially oriented
Polypropylene Film

Impregnant

Non-PCB bio-degradable impregnant

Non-PCB bio-degradable impregnant

Discharge Device

Discharge Resistor

Discharge Resistor

Electrodes

Special vaccuum deposited metal


alloy with re-inforced edge.

Special double side vacuum


deposited metal coating

12/2

www.LNTEBG.com

TECHNICAL DATA

Series

16 F

20 F

Type

MD

FF

MD Type Capacitor unit

FF/APP/ALL-PP Capacitor unit

Standards

IS 13585-1994

IS 13585-1994

Rated voltage

415/440 V (Other ratings on request)

415/440 V (Other ratings on request)

Overvoltage

Un Continuous

Un Continuous

Un + 15% (up to 12 hours daily)

Un + 15% (up to 12 hours daily)

Un + 20% (up to 30 minutes daily)

Un + 20% (up to 30 minutes daily)

Un + 25% (up to 5 minutes daily)

Un + 25% (up to 5 minutes daily)

Un + 30% (up to 1 minute)

Un + 30% (up to 1 minute)

Any overvoltage>1.15 Un shall not occur

Any overvoltage>1.15 Un shall not occur

more than 200 times in the Capacitors life

more than 200 times in the Capacitors life

As per IS 13585 clause 6.1.1

As per IS 13585 clause 6.1.1

1.43 In at 1.15 Cn combined with

1.43 In at 1.15 Cn combined with

overvoltage & presence of harmonics,

overvoltage & presence of harmonics,

As per clause 6.2 of IS 13585

As per clause 6.2 of IS 13585

Frequency (Hz)

50 / 60

50 / 60

No of phases

Single (or) Three

Single (or) Three

Capacitance tolerance

-5% to 15%

-5% to 10%

Overcurrent

Test voltage, terminal / terminal

2.15 . Un

2.15 . Un

Test voltage, terminal / case

3.6 kV AC

3.6 kV AC

(Insulation level)
Peak transient overcurrent

200 x In

200 x In times rated current

Losses

2.5 W / kVAr

0.8 W / kVAr

Total

Degree of protection

IP 31

IP 31

Ambient temperature category

-25 / D (Maximum 55 deg C)

-25 / D (Maximum 55 deg C)

Maximum permissible altitude

2000m above mean sea level

2000m above mean sea level

Mounting position

Vertical with terminal upwards

Vertical with terminal upwards

Safety features

Internal Fuses

Internal Fuses

(Operation co-ordinated with case-rupture

(Operation co-ordinated with case-rupture

characteristics to avoid bursting)

characteristics to avoid bursting)

Container type

M.S. Sheet Metal

M.S. Sheet Metal

Finish

Enamel Paint Finish

Enamel Paint Finish

Dielectric

Combination of Capacitor tissue paper and

Bi-axially oriented hazy Polypropylene Film

12

bi-axially oriented Polypropylene Film


Impregnant

Non-PCB bio-degradable impregnant

Non-PCB bio-degradable impregnant

Discharge Device

Discharge Resistor

Discharge Resistor

Electrodes

High purity, annealed aluminium condensor foil

High purity, annealed aluminium condensor foil

www.LNTEBG.com

12/3

OVERALL DIMENSIONS - SERIES 26 D, TYPE MPP-D

ORDERING DATA - SERIES 26 D, TYPE MPP-D

12

Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1


THREE PHASE CAPACITORS, MPP-D TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

Dimensions of unit
(mm)

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

Ordering
Code for
440V

1.39

26D3010A1

1.31

26D3010B1

124

2.78

26D3020A1

2.62

26D3020B1

4.17

26D3030A1

3.94

5.56

26D3040A1

6.95

8.35

415V

440V

H1

H1

104

56

118

122

124

104

56

147

152

26D3030B1

173

153

56

147

137

5.24

26D3040B1

173

153

56

147

137

26D3050A1

6.56

26D3050B1

173

153

56

163

152

26D3060A1

7.87

26D3060B1

173

153

56

175

167

Note: All dimensions are in mm.


12/4

www.LNTEBG.com

W1

OVERALL DIMENSIONS - SERIES 19 M, TYPE MPP-S

ORDERING DATA - SERIES 19 M, TYPE MPP-S

12

Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1


THREE PHASE CAPACITORS, MPP-S TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

In
at 415V
Amps

Ordering
Code for
415V

7.5

10.43

19M3075A3

10

13.91

12.5

In
at 440V
Amps

Dimensions of unit
(mm)

Ordering
Code for
440V

H1

H2

9.84

19M3075B3

94

200

280

80

19M3100A3

13.12

19M3100B3

94

200

280

80

17.39

19M3125A3

16.4

19M3125B3

94

300

380

80

15

20.87

19M3150A3

19.68

19M3150B3

94

300

380

80

20

27.82

19M3200A3

26.24

19M3200B3

94

300

380

80

25

34.78

19M3250A3

32.80

19M3250B3

94

300

380

80

H3

Note: All dimensions are in mm.

www.LNTEBG.com

12/5

OVERALL DIMENSIONS - SERIES 80 M, TYPE MPP-H

ORDERING DATA - SERIES 80 M, TYPE MPP-H

12

Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1


THREE PHASE CAPACITORS, MPP-H TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

In
at 415V
Amps

Ordering
Code for
415V

7.5

10.43

80M3075A3

10

13.91

12.5

In
at 440V
Amps

Dimensions of unit
(mm)

Ordering
Code for
440V

HI

H2

H3

9.84

80M3075B3

94

300

380

80

80M3100A3

13.12

80M3100B3

94

300

380

80

17.39

80M3125A3

16.4

80M3125B3

94

300

380

80

15

20.87

80M3150A3

19.68

80M3150B3

154

300

380

80

20

27.82

80M3200A3

26.24

80M3200B3

154

300

380

80

25

34.78

80M3250A3

32.80

80M3250B3

154

300

380

80

Note: All dimensions are in mm.


12/6

www.LNTEBG.com

OVERALL DIMENSIONS - SERIES 61 M, TYPE MD-XL

ORDERING DATA - SERIES 61 M, TYPE MD-XL

12

Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1


THREE PHASE CAPACITORS, MD-XL TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

7.5

10.43

61M3075A3

9.84

10

13.91

61M3100A3

12.5

17.39

15

Ordering
Code for
440V

Dimensions of unit
(mm)
D

HI

H2

H3

61M3075B3

94

300

380

80

13.12

61M3100B3

94

300

380

80

61M3125A3

16.4

61M3125B3

94

300

380

80

20.87

61M3150A3

19.68

61M3150B3

154

300

380

80

20

27.82

61M3200A3

26.24

61M3200B3

154

300

380

80

25

34.78

61M3250A3

32.80

61M3250B3

154

300

380

80

Note: All dimensions are in mm.

www.LNTEBG.com

12/7

OVERALL DIMENSIONS - SERIES 16 F, TYPE MD

ORDERING DATA - SERIES 16 F, TYPE MD

12

Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1


16F CAPACITOR UNIT: THREE PHASE CAPACITORS, MD TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

10

13.91

16F3100A3

13.12

12.5

17.39

16F3125A3

15

20.87

20
25

Ordering
Code for
440V

Dimensions of unit
415V
W1

H1

H2

H1

H2

16F3100B3

350

325

156

236

138

218

16.4

16F3125B3

350

325

179

259

167

247

16F3150A3

19.68

16F3150B3

350

325

216

296

189

269

27.82

16F3200A3

26.24

16F3200B3

350

325

280

360

244

324

34.78

16F3250A3

32.80

16F3250B3

350

325

325

405

300

380

Note: All dimensions are in mm.


12/8

440V

www.LNTEBG.com

OVERALL DIMENSIONS - SERIES 20 F, TYPE FF

ORDERING DATA - SERIES 20 F, TYPE FF

12

Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1


20F CAPACITOR UNIT: THREE PHASE CAPACITORS, FF/APP/ALL PP TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

Ordering
Code for
440V

10

13.91

20F3100A3

13.12

12.5

17.39

20F3125A3

15

20.87

20
25

Dimensions of unit
415V

440V

W1

H1

H2

W1

H1

H2

20F3100B3

383

363

158

243

383

363

148

233

16.4

20F3125B3

383

363

186

271

383

363

171

256

20F3150A3

19.68

20F3150B3

383

363

215

300

383

363

200

285

27.82

20F3200A3

26.24

20F3200B3

383

363

266

351

383

363

246

331

34.78

20F3250A3

32.80

20F3250B3

383

363

320

405

383

363

300

385

Note: All dimensions are in mm.

www.LNTEBG.com

12/9

OVERALL DIMENSIONS

Type

MPP-S

335

263

160 210

MPP-H

450

310

275 325

MD-XL

450

310

275 325

ORDERING DATA
Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1
THREE PHASE CAPACITOR BANKS, MPP-S TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

12

Unit
Config.

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

Ordering
Code for
440V

AI.
Bus Bar
Size, mm

30

15+15

41.78

19M3300A3

39.41

19M3300B3

25 x 6

480

35

20+15

48.75

19M3350A3

45.98

19M3350B3

25 x 6

480

40

20+20

55.71

19M3400A3

52.55

19M3400B3

25 x 6

480

45

20+25

62.28

19M3450A3

59.12

19M3450B3

25 x 6

480

50

25+25

69.64

19M3500A3

65.68

19M3500B3

25 x 6

480

THREE PHASE CAPACITOR BANKS, MPP-H TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
30

15+15

41.78

80M3300A3

39.41

80M3300B3

25 x 6

480

35

20+15

48.75

80M3350A3

45.98

80M3350B3

25 x 6

480

40

20+20

55.71

80M3400A3

52.55

80M3400B3

25 x 6

480

45

20+25

62.28

80M3450A3

59.12

80M3450B3

25 x 6

480

50

25+25

69.64

80M3500A3

65.68

80M3500B3

25 x 6

480

THREE PHASE CAPACITOR BANKS, MD-XL TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
30

15+15

41.78

61M3300A3

39.41

61M3300B3

25 x 6

480

35

20+15

48.75

61M3350A3

45.98

61M3350B3

25 x 6

480

40

20+20

55.71

61M3400A3

52.55

61M3400B3

25 x 6

480

45

20+25

62.28

61M3450A3

59.12

61M3450B3

25 x 6

480

50

25+25

69.64

61M3500A3

65.68

61M3500B3

25 x 6

480

Note: All dimensions are in mm.


12/10

www.LNTEBG.com

OVERALL DIMENSIONS

ORDERING DATA
Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1
16F BANKS: THREE PHASE CAPACITOR BANKS, MD TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

Unit
Config.

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

Ordering
Code for
440V

AI.
Bus Bar
Size, mm

For 415 V

For 440 V

30

15+15

41.78

16F3300A3

39.41

16F3300B3

25 x 6

350

411

355

384

40

20+20

55.71

16F3400A3

52.55

16F3400B3

25 x 6

350

475

355

439

50

25+25

69.64

16F3500A3

65.68

16F3500B3

25 x 6

350

520

355

495

20F BANKS: THREE PHASE CAPACITOR BANKS, FF/APP/ALL PP TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
30

15 x 2

41.78

20F3300A3

39.41

20F3300B3

25 x 6

383

400

383

385

40

20 x 2

55.71

20F3400A3

52.55

20F3400B3

25 x 6

383

451

383

431

50

25 x 2

69.64

20F3500A3

65.68

20F3500B3

25 x 6

383

505

383

485

Note: All dimensions are in mm.

www.LNTEBG.com

12/11

12

OVERALL DIMENSIONS

Type

MPP-S

450

263

275 320

MPP-H

625

310

450 500

MD-XL

625

310

450 500

ORDERING DATA
Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1
THREE PHASE CAPACITOR BANKS, MPP-S TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

12

Unit
Config.

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

Ordering
Code for
440V

AI.
Bus Bar
Size, mm

55

20+20+15

79.90

19M3550A3

72.25

19M3550B3

25 x 6

480

60

20+20+20

83.57

19M3600A3

78.82

19M3600B3

25 x 6

480

65

25+20+20

90.54

19M3650A3

85.39

19M3650B3

30 x 6

480

75

25+25+25

104.46

19M3750A3

98.53

19M3750B3

30 x 6

480

THREE PHASE CAPACITOR BANKS, MPP-H TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
55

20+20+15

76.60

80M3550A3

72.25

80M3550B3

25 x 6

480

60

20+20+20

83.57

80M3600A3

78.82

80M3600B3

25 x 6

480

65

25+20+20

90.54

80M3650A3

85.39

80M3650B3

30 x 6

480

75

25+25+25

104.46

80M3750A3

98.53

80M3750B3

30 x 6

480

THREE PHASE CAPACITOR BANKS, MD-XL TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
55

20+20+15

76.60

61M3550A3

72.25

60

20+20+20

83.57

61M3600B3

78.82

61M3600B3

25 x 6

480

65

25+20+20

90.54

61M3650A3

85.39

61M3650B3

30 x 6

480

75

25+25+25

104.46

61M3750A3

98.53

61M3750B3

30 x 6

480

Note: All dimensions are in mm.


12/12

www.LNTEBG.com

61M3550B3

25 x 6

480

OVERALL DIMENSIONS

ORDERING DATA
Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1
16F BANKS: THREE PHASE CAPACITOR BANKS, MD TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

Unit
Config.

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

Ordering
Code for
440V

AI.
Bus Bar
Size, mm

For 415 V

For 440 V
H

45

15 x 3

62.68

16F3450A3

59.12

16F3450B3

25 x 6

350

411

355

384

60

20 x 3

83.57

16F3600A3

78.82

16F3600B3

25 x 6

350

475

355

439

75

35 x 3

104.46

16F3750A3

98.53

16F3750B3

30 x 6

350

520

355

495

20F BANKS: THREE PHASE CAPACITOR BANKS, FF/APP/ALL PP TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
45

15 x 3

62.68

20F3450A3

59.13

20F3450B3

25 x 6

383

400

383

385

60

20 x 3

83.57

20F3600A3

78.82

20F3600B3

25 x 6

383

451

383

431

75

25 x 3

104.46

20F3750A3

98.53

20F3750B3

30 x 6

383

505

383

485

Note: All dimensions are in mm.

www.LNTEBG.com

12/13

12

OVERALL DIMENSIONS

Type

MPP-S

565

263

390 440

MPP-H

795

310

620 670

MD-XL

795

310

620 670

ORDERING DATA
Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1
THREE PHASE CAPACITOR BANKS, MPP-S TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

12

Unit
Config.

In
at 415V
Amps

Ordering
Code for
415V

In
at 440V
Amps

Ordering
Code for
440V

AI.
Bus Bar
Size, mm

80

20+20+20+20

111.43

19M3800A3

105.10

19M3800B3

50 x 6

480

85

25+20+20+20

118.39

19M3850A3

111.66

19M3850B3

50 x 6

480

90

25+25+20+20

132.32

19M3900A3

118.23

19M3900B3

50 x 6

480

95

25+25+25+20

132.32

19M3950A3

124.80

19M3950B3

50 x 6

480

100

25+25+25+25

139.28

19M3X10A3

131.37

19M3X10B3

50 x 6

480

THREE PHASE CAPACITOR BANKS, MPP-H TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
80

20+20+20+20

111.43

80M3800A3

105.10

80M3800B3

50 x 6

480

85

25+20+20+20

118.39

80M3850A3

90

25+25+20+20

125.36

80M3900A3

111.66

80M380B3

50 x 6

480

118.23

80M3900B3

50 x 6

95

25+25+25+20

132.32

480

80M3950A3

124.80

80M3950B3

50 x 6

480

100

25+25+25+25

139.28

80M3X00A3

131.37

80M3X00B3

50 x 6

480

THREE PHASE CAPACITOR BANKS, MD-XL TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
80

20+20+20+20

11.43

61M3800A3

105.10

61M3800B3

50 x 6

480

85

25+20+20+20

118.39

61M3850A3

111.66

61M3850B3

50 x 6

480

90

25+25+20+20

125.36

61M3900A3

118.23

61M3900B3

50 x 6

480

95

25+25+25+20

132.32

61M3950A3

124.80

61M3950B3

50 x 6

480

100

25+25+25+25+

139.28

61M3X00A3

131.37

61M3X00B3

50 x 6

480

Note: All dimensions are in mm.


12/14

www.LNTEBG.com

OVERALL DIMENSIONS

ORDERING DATA
Conformance to IS 13947 (Part 4/Sec.1) and IEC:60947-4-1
16F BANKS: THREE PHASE CAPACITOR BANKS, MD TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
Output,
Qn
kVAr

Unit
Config.

In
at 415V

Ordering
Code for
415V

In
at 440V

Ordering
Code for
440V

AI.
Bus Bar
Size, mm

For 415 V
D

For 440 V
H

80

20 x 4

111.43

16F3800A3

105.10

16F3800B3

50 x 6

350

475

355

439

100

25 x 4

139.28

16F3X00A3

131.37

16F3X00B3

50 x 6

350

520

355

495

20F BANKS: THREE PHASE CAPACITOR BANKS, FF/APP/ALL PP TYPE, RATED VOLTAGE 415/440 VAC, 50 HZ, DELTA CONN.
80

20 X 4

111.43

20F3800A3

105.10

20F3800B3

50 x 6

383

451

383

431

100

25 x 4

139.28

20F3X00A3

131.37

20F3X00B3

50 x 6

383

505

383

485

(Manufactured by Meher Capacitors Pvt. Ltd.)


Note: All dimensions are in mm.

www.LNTEBG.com

12/15

12

intellVAr APFC PANELS


IntellVAr APFC
TECHNOLOGY
& TYPES
IntellVAr
APFC
TECHNOLOGY
& TYPES
Sl. No.

PRODUCT

INCOMER

CONTROL

DESCRIPTION

IntellVAr-S

SDF / MCCB

Auto / Auto + Manual

Standard Version

IntellVAr-F

MCCB

Auto / Auto + Manual

Fuseless Version

IntellVAr-C

SDF / MCCB

Auto / Auto + Manual

Compartmentalised Version (Available on request)

IntellVAr-D

SDF / MCCB

Automatic

Dynamic Compensation (Thyristor Switched) Version

TECHNICAL DATA
Series

IntellVAr-S, IntellVAr-F , IntellVAr-D

Type of Capacitors

MPP-H, MD-XL, FF

Standards
Capacitors

IS 2834 -1986, IEC 831-1, IEC 831-2

Reactor

IS 5553, IEC 76 /3, VDE 0532

Switchgear

12

- Contactors

IS 13947 part 4 / sec-1

- Fuses

IS 13924 part 1 &2 , IS 9224 part 1 & 2, IEC 269, part 1 & 2.

- SDF

IS 13947 part 3 , IEC 947 -3

- MCB

IS 8828 part 2 , IEC 898.

- MCCB

IS 13947 part 2 , IEC 947 -2

APFC Relay

CE

APFC Panel

IS 8623

Rated Voltage

440 V

No of Phases

Frequency (Hz)

50

Overvoltage

As per above standards

Overcurrent

As per above standards

Enclosure
Material

Sheet Steel

Enclosure frame

9 - fold profiled

Rear panel

1.5 mm

Doors

2.0 mm

Paint

Dipcoated primed and powder coated in texture RAL 7032

Application
Degree of protection
12/16

Indoor
IP42
www.LNTEBG.com

TECHNICAL DATA

Ambient temperature category

- 25 / D (Max 55 deg C)

Losses

2 W / kVAr

Mounting position

35 - 75 kVAr

Wall mounting

100 - 300 kVAr

Free standing floor mounting

Saftey features

Short circuit protection

Additional safety features

Emergency push button

Maximum permissible altitude

2000m

Bus Bar Adaptor Technology

60 mm system technology

Main busbar

30 x 10 tinned Cu

Standard

DIN 43671

Incoming Bus bar

Aluminium

NH Bus mounting fuse base with grip cover


Bus Bar Support

SMC, Silicon free, chlorine free

Temperature withstand

120 deg C

Standard

UL 94-V0

Short circuit withstand

50 kA

Standard features

Voltmeter with selector switch, Ammeter with selector (not provided in


IntellVAr-D) switch, Door interlock, R Y B indicating lamps,
Emergency push button.

12

www.LNTEBG.com

12/17

ORDERING DATA & OVERALL DIMENSIONS

INTELL VAR-S STANDARD APFC PANEL WITH MPP-H CAPACITORS, SDF INCOMER & AUTOMATIC CONTROL
RATED VOLTAGE 440 V / 50 HZ. CONTROL VOLTAGE 230 V / 50 HZ.
KVAr

Output
Steps

Switching
sequence

Cat. No.

Incomer
SDF

Switching Stages
1

Dimensions
W x H x D (mm)

35

7x5

1:2:4

A0358B07SSA

FN-100

10

20

800x1000x300

40

4 x 10

1:1:2

A0408B04SSA

FN-100

10

10

20

800x1000x300

40

8x5

1:2:2:3

A0408B08SSA

FN-100

10

10

15

800x1000x300

50

5 x 10

1:2:2

A0508B05SSA

FN-100

10

20

20

800x1000x300

50

10 x 5

1:2:2:5

A0508B10SSA

FN-100

10

10

25

800x1000x300

60

6 x 10

1:2:3

A0608B06SSA

FN-125

10

20

30

800x1000x300

60

12 x 5

1:2:4:5

A0608B12SSA

FN-125

10

20

25

800x1000x300

75

6 x 12.5

1:2:3

A0758B06SSA

FN-200

12.5

25

37.5

800x1000x300

INTELL VAR-S STANDARD APFC PANEL WITH MPP-H CAPACITORS, SDF INCOMER & AUTOMATIC CONTROL RATED
VOLTAGE 440 V / 50 HZ. CONTROL VOLTAGE 230 V / 50 HZ.
KVAr

12

Output
Steps

Switching
sequence

Cat. No.

Incomer
SDF

Switching Stages
1

100

4 x 25

1:1:2

A1008B04SSA

FN-200

25

100

8 x 12.5

1:1:2:4

A1008B08SSA

FN-200

12.5

100

10 x 10

1:2:2:5

A1008B10SSA

FN-200

125

5 x 25

1:2:2

A1258B05SSA

125

10 x 12.5

1:2:3:4

A1258B10SSA

150

6 x 25

1:2:3

150

12 x 12.5

1:1:2:4:4

150

15 x 10

1:2:2:5:5

175

7 x 25

175

14 x 12.5

200

Dimensions
W x H x D (mm)

25

50

800x2000x600

12.5

25

50

800x2000x600

10

20

20

50

800x2000x600

FN-250

25

50

50

800x2000x600

FN-250

12.5

25

37.5

50

800x2000x600

A1508B06SSA

FN-315

25

A1508B12SSA

FN-315

12.5

A1508B15SSA

FN-315

10

1:2:4

A1758B07SSA

FN-400

25

1:1:2:4:6

A1758B14SSA

FN-400

12.5

4 x 50

1:1:1:1

A2008B04SSA

FN-400

50

200

8 x 25

1:1:2:2:2

A2008B08SSA

FN-400

25

200

16 x 12.5

1:1:2:4:4:4

A2008B16SSA

FN-400

12.5

225

9 x 25

1:2:2:2:2

A2258B09SSA

FN-630

25

225

18 x 12.5

1:1:2:4:4:6

A2258B18SSA

FN-630

12.5

250

5 x 50

1:1:1:1:1

A2508B05SSA

FN-630

250

10 x 25

1:1:2:2:2:2

A2508B10SSA

275

11 x 25

1:2:2:2:2:2:

300

6 x 50

300

12 x 25

12/18

50

75

800x2000x600

12.5

25

50

50

800x2000x600

20

20

50

50

800x2000x600

50

100

800x2000x600

12.5

25

50

75

800x2000x600

50

50

50

800x2000x600

25

50

50

50

800x2000x600

12.5

25

50

50

50

800x2000x600

50

50

50

50

800x2000x600

12.5

25

50

50

75

800x2000x600

50

50

50

50

50

800x2000x600

FN-630

25

25

50

50

50

50

800x2000x600

A2758B11SSA

FN-630

25

50

50

50

50

50

800x2000x600

1:1:1:1:1:1

A3008B06SSA

FN-630

50

50

50

50

50

50

800x2000x600

1:1:2:2:2:4

A3008B12SSA

FN-630

25

25

50

50

50

100

800x2000x600

www.LNTEBG.com

ORDERING DATA

INTELL VAR-F, FUSELESS APFC PANEL WITH MPP-H CAPACITORS, MCCB INCOMER & AUTOMATIC OPTION
RATED VOLTAGE 440 V / 50 HZ, CONTROL VOLTAGE 230 V / 50 HZ.
KVAr

Output
Steps

Switching
sequence

Switching Stages

Cat. No.

Incomer
SDF

Dimensions
W x H x D (mm)

25

50

800x2000x600

12.5

25

50

800x2000x600

100

4 x 25

1:1:2

A1008B04FMA

DTH-200

25

100

8 x 12.5

1:1:2:4

A1008B08FMA

DTH-200

12.5

100

10 x 10

1:2:2:5

A1008B10FMA

DTH-200

10

20

20

50

800x2000x600

125

5 x 25

1:2:2

A1258B05FMA

DTH-250

25

50

50

800x2000x600

125

10 x 12.5

1:2:3:4

A1258B10FMA

DTH-250

12.5

25

37.5

50

800x2000x600

150

6 x 25

1:2:3

A1508B06FMA

DTH-400

25

50

75

800x2000x600

150

12 x 12.5

1:1:2:4:4

A1508B12FMA

DTH-400

12.5

12.5

25

50

50

800x2000x600

150

15 x 10

1:2:2:5:5

A1508B15FMA

DTH-400

10

20

20

50

50

800x2000x600

175

7 x 25

1:2:4

A1758B07FMA

DTH-400

25

50

100

800x2000x600

175

14 x 12.5

1:1:2:4:6

A1758B14FMA

DTH-400

12.5

12.5

25

50

75

800x2000x600

200

4 x 50

1:1:1:1

A2008B04FMA

DTH-400

50

50

50

50

800x2000x600

200

8 x 25

1:1:2:2:2

A2008B08FMA

DTH-400

25

25

50

50

50

800x2000x600

200

16 x 12.5

1:1:2:4:4:4

A2008B16FMA

DTH-400

12.5

12.5

25

50

50

50

800x2000x600

225

9 x 25

1:2:2:2:2

A2258B09FMA

DTH-630

25

50

50

50

50

800x2000x600

225

18 x 12.5

1:1:2:4:4:6

A2258B18FMA

DTH-630

12.5

12.5

25

50

50

75

800x2000x600

250

5 x 50

1:1:1:1:1

A2508B05FMA

DTH-630

50

50

50

50

50

800x2000x600

250

10 x 25

1:1:2:2:2:2

A2508B10FMA

DTH-630

25

25

50

50

50

50

800x2000x600

275

11 x 25

1:2:2:2:2:2

A2758B11FMA

DTH-630

25

50

50

50

50

50

800x2000x600

300

6 x 50

1:1:1:1:1:1

A3008B06FMA

DTH-630

50

50

50

50

50

50

800x2000x600

300

12 x 25

1:1:2:2:2:4

A3008B12FMA

DTH-630

25

25

50

50

50

100

800x2000x600

INTELL VAR-D THYRISTOR SWITCHED (DYANAMIC COMPENSATION) APFC PANEL WITH MPP-H CAPACITORS,
SDF INCOMER & AUTOMATIC OPTION. (CLOSED LOOP) WITH SERIES REACTORS
RATED VOLTAGE 440 V / 50 HZ.
KVAr

Output
Steps

Switching
sequence

Cat. No.

Incomer
SDF

Switching Stages
1

Dimensions
W x H x D (mm)

100

2x50

1:1

A1008B02DSC

FN 200

50

50

800x2200x800

150

3x50

1:1:1

A1508B03DSC

FN 315

50

50

50

800x2200x800

200

4x50

1:1:1:1

A2008B04DSC

FN 400

50

50

50

50

1600x2200x800

250

5x50

1:1:1:1:1

A2508B05DSC

FN 630

50

50

50

50

50

1600x2200x800

300

6x50

1:1:1:1:1:1

A3008B06DSC

FN 630

50

50

50

50

50

50

1600x2200x800

www.LNTEBG.com

12/19

12

FIXED DETUNED FILTER COMPONENTS


FILTER CAPACITORS

3PHASE, CAPACITORS, MD-XL TYPE : RATED VOLTAGE 500V AC, 50HZ, DELTA CONNECTED
Output
kVAr

In at 500V.
Amps.

15

17.32

30

34.64

12

Dimensions in mm.
D

H1

H2

H3

Ref.
Fig.

61M3165M3

94

283

391

80

9.3

61M3330M3

154

283

391

80

9.3

Ordering Code

Temperature switch to disconnect


the power supply

REACTORS FOR DETUNED FILTERS


MD-XL CAPACITOR UNIT

12/20

www.LNTEBG.com

FIXED DETUNED FILTER COMPONENTS

12
Series Reactors

THE VALUES AND DIMENSIONS OF THE SERIES REACTOR TO BE USED IN SERIES WITH THE CAPACITOR IS
SHOWN IN THE TABLE
Value in
MH

3.709
1.855
0.928
0.618
0.464

Ordering Code

FR3370125B0
FR3370250B0
FR3370500B0
FR3370750B0
FR3371000B0

180
230
300
300
300

180
205
240
270
270

Dimensions in mm
T

105
140
170
200
200

www.LNTEBG.com

Ref.
o

Fig.

136
176
224
224
224

77
95
119
147
147

7
7
10
10
10

9.4
9.4
9.4
9.4
9.4

12/21

ORDERING DATA
Fixed Detuned Filters

FIXED DETUNED FILTERS WITH MD-XL CAPACITORS & SDF INCOMER


Capacitor Reactor Dimensions
(kVAr)
(mH) W x H x D (mm)

KVAr

Cat. No.

I/c

Contactor

12.5

FB3701256BS

FN-32

MN - 32

12.5

3.709

800x1000x300

25

FB3702506BS

FN-63

MN - 45

25

1.855

800x1000x300

50

FB3705006BS FN-125

MN - 110

25 x 2

0.928

800x1800x500

75

FB3707506BS FN-200

ML - 10

25 x 3

0.618

800x1800x500

100

FB3710006BS FN-200

ML - 10

25 x 4

0.464

800x1800x500

APFC cum Detuned Filter

INTEL II VAR-H DETUNED FILTER CUM APFC PANEL WITH MD-XL CAPACITORS, SDF INCOMER & AUTOMATIC
OPTION. RATED VOLTAGE 440 V/ 50 HZ, CONTROL VOLTAGE 230 V / 50 HZ
kVAR

12

Output

Switching

Steps

sequence

75

3 x 25

1:2

100

4 x 25

125

Cat No.

Incomer

Switching Stages
1

A 0756B03HSA

FN-200

25

50

1:1:2

A 1006B04HSA

FN-200

25

25

50

800x2000x600

5 x 25

1:2:2

A 1256B05HSA

FN-250

25

50

50

800x2000x600

150

3 x 50

1:1:1

A 1506B03HSA

FN-315

50

50

50

800x2000x600

kVAR

Output

Switching

Cat No.

Incomer

Steps

sequence

SDF

Wx H x D (mm)

150

6 x 25

1:1:2:2

A 1506B06HSA

FN-315

25

25

50

50

1600x2000x600

175

7 x 25

1:2:2:2

A 1756B07HSA

FN-315

25

50

50

50

1600x2000x600

200

4 x 50

1:1:1:1

A 2006B04HSA

FN-315

50

50

50

50

1600x2000x600

200

8 x 25

1:1:2:2:2

A 2006B08HSA

FN-315

25

25

50

50

50

1600x2000x600

225

9 x 25

1:2:2:2:2

A 2256B09HSA

FN-630

25

50

50

50

50

1600x2000x600

250

5 x 50

1:1:1:1:1

A 2506B05HSA

FN-630

50

50

50

50

50

1600x2000x600

250

10 x 25

1:1:2:2:2:2

A 2506B10HSA

FN-630

25

25

50

50

50

50

1600x2000x600

275

11 x 25

1:2:2:2:2:2

A 2756B11HSA

FN-630

25

50

50

50

50

50

1600x2000x600

300

6 x 50

1:1:1:1:1:1

A 3006B06HSA

FN-630

50

50

50

50

50

50

1600x2000x600

12/22

Dimensions

SDF

Wx H x D (mm)
800x2000x600

Switching Stages

www.LNTEBG.com

Dimensions

Potrebbero piacerti anche