Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
AN7124
Dual 3.1 W Audio Power Amplifier
Overview
Unit : mm
(1.3)
12
7.70.3
(10.0)
29.60.3
(1.27)
+0.15
20.00.3
R1.8
(1.2)
19.10.3
21.90.3
3.50.3
1.450.15
1
1.20.1
Radio-cassette
1.800.15
(12.5)
Applications
+0.10
0.25 0.05 2.54
0.6
3.6
(10.0)
29.750.30
28.00.3
Features
HSIP012-P-0000A
Block Diagram
45 dB
45 dB
Over current
thermal
protection
circuit
Mute
12
11
10
VCC
GND
5
GND
Ripple
filter
STB
Pin Descriptions
Pin No.
Description
Pin No.
Description
Stand-by
ch.1 output
Muting
ch.1 bootstrap
ch.2 input
Output GND
ch.1 input
10
VCC
Input GND
11
ch.2 bootstrap
Ripple filter
12
ch.2 output
1
AN7124
Symbol
Rating
Unit
Supply voltage
VCC
24
Supply current
ICC
4.0
Power dissipation
PD
37.5
Topr
25 to +75
Storage temperature
Tstg
55 to +150
Symbol
Range
Unit
VCC
6.0 to 18.0
Symbol
Conditions
Typ
Max
Unit
ICQ
VIN = 0 mV
12
19
26
mA
VNO
VIN = 0 mV,PG = 10 k
0.27
0.5
mVrms
GV
VIN = 3 mV
43
45
47
dB
THD
VIN = 3 mV
0.05
0.5
Maximum output 1
PO1
THD = 10 %
4.3
5.0
Channel balance
CB
VIN = 3 mV
dB
RR
45
50
dB
ISTB
VIN = 0 mV
10
Mut
VIN = 10 mV
60
80
dB
PO2
THD = 10 %,VCC = 9 V
2.5
3.0
CT
50
64
dB
Quiescent current
Output noise voltage
*1
Voltage gain
Total harmonic distortion
Ripple rejection
*1
Standby current
Muting effects
*1
Maximum output 2
Crosstalk
*1,*3
*3
*2
Min
AN7124
1 F
22 F
33 F
3.9 k
1 000 F
2.2
RL
3
Mute
12
11
10
1 000 F
2.2
5 V(On)
STB
47 F
47 F
47 nF
VIN1
1 F 100 F
8.2 k
(Off)5 V
(On)0 V
VIN2
47 nF
1 000 F
RL
3
VCC = 9 V/12 V
0 V(Off)
Characteristics Curve
PD Ta
70
62.5 W
60
50
(1)
40
30
20.8 W
(2)
20
15.6 W
(3)
10
3.0 W
(4)
0
0
40
80
120
160
1. TC = Ta (j-c = 2 C/W)
2. 20.83 W (f = 4.0 C/W)
With a 100 cm2 3 mm Al heat sink (black
colour coated) or a 200 cm 2 2 mm Al
heat sink (not lacquered)
3. 15.63 W (f = 6.0 C/W)
With a 100 cm2 2 mm Al heat sink(not
lacquered)
4. 3.0 W at Ta = 25 C (j-a = 42 C/W)
Without heat sink
AN7124
Application Note
1.Voltage gain
The close loop gain of AN7124 is fixed at 45 dB(typ.)
GV = 20 log(
R1
84
R2
R1
R2
15 k
2.Standby function
Standby is ON when Pin1 is set to "L". By applying a 5 V to the standby pin, transistor Q1 will be turned ON to
provide a constant current (I) for driving other parts of the circuit. The RC is to create a TIME CONSTANT for the
standby pulse during charging and discharging.
Off
5V
VCC
ZSTBY
Stb
1
I
ON<2.8 V<OFF
On
Q1
3.Muting
By controlling Pin2 from "H" to "L", the mute function is set from ON to OFF. When Pin2 is floating, DC 0.02
V. The threshold is set 2.8 V. The RC is to create a TIME CONSTANT for the mute pulse during charging and
discharging.
Bias
Off
5V
Mute
C
On
ZMUTE
10 % mute = 1.5 V
90 % mute = 2.8 V
Impedance, ZMUTE 45 k
AN7124
Pin7,12
C
47 nF
2.2
5.Bootstrap
The capacitor C connected between the output and bootstrap pin helps to increase the output dynamic range and
hence increases the output power of the IC.
pp
VCC
Pin8,11
47 F
Pin7,12
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.