3. Select XZ plane and create the sketch as shown Use symmetric protrude, depth 33mm 4Hareesha N G, Dept of AE, DSCE 4. Select front surface as shown and create the sketch as shown Use cut out, dep th 6.5 mm 5Hareesha N G, Dept of AE, DSCE 5. Use smart mirror option and select previously created feature, and select mid plane as shown 6Hareesha N G, Dept of AE, DSCE 6. Create a parallel plane at distance of 84 from right side surface of the main body and create sketch as shown in fig 1. On right side surface of the main bod y as shown, create the sketch as shown in fig 2. fig 2 fig 1 7Hareesha N G, Dept of AE, DSCE 7. Use lofted protrusion to create the feature as shown below. 8Hareesha N G, De pt of AE, DSCE 8. Select YZ plane and create the sketch as shown Use Hole option to create the hole as shown below. 9Hareesha N G, Dept of AE, DSCE 9. Use smart mirror option to create the feature as shown below and select the m id plane, select both previously created features 10Hareesha N G, Dept of AE, DS CE 10. Create angled plane as shown below. Giving 60O angle wrt horizontal plane, t aking vertical plane as intersection. Create a parallel plane as shown at distan ce 42mm from the previously created angled plane. Create hole on parallel plane as shown below. Take front plane create 30 deg line as shown. 11Hareesha N G, De pt of AE, DSCE 11. On this 30 deg angled plane create hole as shown below. Also create cutout a s shown for depth of 7mm 12Hareesha N G, Dept of AE, DSCE 12. Mirror the previously created both features as shown below. Selecting smart mirror option and mid plane. Create 3 circles of 24, 26, 24 mm respectively on p arallel planes as shown in fig below. Use lofted protrusion to create the featur e shown, selecting those three circles. 13Hareesha N G, Dept of AE, DSCE 13. create cut out as shown. create protrusion as shown, selecting previously cr eated sketch and using up to next option Create oil hole using below sketch and using revolved cut out command 14Hareesha N G, Dept of AE, DSCE 14. Part-2 : Bush Select XY plane, create the sketch as shown in fig, create fea ture as shown giving depth of 25mm, symmetric. Create the sketch, on parallel pl ane which is at a distance of 9mm from center of cylinder, as shown in fig 2 and create cutout, give 0.5 depth Create cutout with 2mm dia circle, use upto next. 15Hareesha N G, Dept of AE, DSCE 15. 16Hareesha N G, Dept of AE, DSCE 16. 17Hareesha N G, Dept of AE, DSCE 100o degree revolved cutout 45o to front pl ane 90o to 450 plane 2mm hole on 90o plane 17. 18Hareesha N G, Dept of AE, DSCE 0.5 mm cutout Sketch on the new plane Sketc h on the 90o plane which was created earlier 0.5 mm cutout 18. 19Hareesha N G, Dept of AE, DSCE Mirror other side 1.5 mm cutout from bottom 19. 20Hareesha N G, Dept of AE, DSCE Sketch on plane normal to curve Swept Protr usion Sketch parallel plane 20. 21Hareesha N G, Dept of AE, DSCE Protrusion upto next Cutout through all 21. 22Hareesha N G, Dept of AE, DSCE Sketch 0n 3mm parallel plane from bottom, c utout 16 mm 2 mm cutout 1 mm round Through all, cutout 22. 23Hareesha N G, Dept of AE, DSCE Mirror other side Round 10mm both side Mirr or all features other side 1.5 mm cutout , from bottom Sketch on plane normal to curve Protrusion upto next, taper 5o 23. 24Hareesha N G, Dept of AE, DSCE Counter sink Hole, through all 24. 25Hareesha N G, Dept of AE, DSCE 25. 26Hareesha N G, Dept of AE, DSCE 26. 27Hareesha N G, Dept of AE, DSCE 27. 28Hareesha N G, Dept of AE, DSCE