Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. (a) Explain with neat sketches the working principal of general heat conduction of
a heat transfer ?.
(b) Explain about the initial and boundary of the conditions?
2. (a) Explain about the simplified heat transfer in 1D and 2D FINS ?.
(b) Explain about different modes of heat transfer ?.
3. (a) Explain about the Lumped system analysis and semi infinite of a solids of a
2D transient heat
conduction ?.
(b) The initial uniform temperature of a thick concrete wall (=1.610m/s,
k=0.94w/m c) of a jet
Engine test cell is 25c.The surface temperature of the wall suddenly rises to
340c when the wall
Combination of exhaust gases from the turbojet and spray of cooling water
occurs Determine:
(1) The temperature at a point 80 mm from the surface after 8 hours :
(2) The instantaneous heat flow rate at the specified plane and at the surface
itself at the instant
Mentioned at (1).
Use of solution for semi infinite solid.
4. (a) Explain about the concepts of a continuity and momentum of the forced
convection of the
Equations ?
(b) Explain about the Derivation of energy equation and Dimensional analysis of
a Similitude?
5. (a) Air at 20c flows over a thin plate with a velocity of 3m/sec. The plate is 2 m
long and 1m
Wide. Estimate the boundary layer thickness at the trailing edge of the plate
and total drag
Force experienced by the plate also calculate the mass flow of air which enters
the boundary
Layer between x=30cm and x=80cm.The physical properties of air 20c are:
P = 1017kg/m, v = 15 10m/s.
(b) Water at 25c flows through a tube of 100 mm diameter. Determind the flow
rate that will result
In a Reynolds number of 1500. The tube is provided with a nichrome heating
element on its surface
And receives a sonstant heat flux of 400 W/m length of the tube. Determind the
average heat trans-fer co efficient between the water and the tube wall , assuming fully
developed conditions. Also
Determine the length of the tube for the bulk temperature of water to rise from
25cto 30c.
SUB: ADVANCED ENERGY TECHNOLOGIES
1.(a) Explain with neat sketh of a lamont boiler and discuss the relative merits and
demerits ?.
(b) Explain about the causes of boiler tube failures and prevention ?.
2.(a) Explain with neat sketchs of a supercharged boilers and waste heat boilers ?.
(b) Explain with neat sketch of a Loeffler boiler and discuss the relative merits
and demerits ?.
3.(a) Explain different types of a FBC and working principal of FBC ?.
(b) Explain about the corrosion of FBC system and control of FBC systems ?.
4.(a) Briefly explain about the Erosion and corrosion and its prevention in FBC
boilers ?.
(b) What are the advantages and disadvantages of a FBC systems ?.
5.(a) Explain with neat sketch the combined cycle with gas production from coal and
arrangement of
Combined cycle ?.
(b) Briefly explain about the combined cycles using PFBC system ?.
SUB:ENERGY AUDITING AND MANAGEMENT
1.(a) Explain about rules for efficient energy conservation ?.
(b) State general principls of Qualities and functions of energy managers ?.
2.(a) What is energy auditing ? What are the objectives of it and level of
responsibility of a control
Of energy ?.
(b) Explain process of energy conservation schemes and sankey diagrams of a
load profiles ?.
3.(a) How many types of a energy Audits ?. Explain briefly the Questinnarie of a
energy Audit of
Industries ?.
(b) Explain about the General energy audit and detailed of energy audit of a
energy saving potential ?.
4.(a) Explain about effect of insulation on on current carrying wires and economic
thickness of insulation
(b) Explain about the critical radius of insulation ?.
5.(a) What are the properties of theramal insulations ?.
(b) What are the classification of insulation materials ?
SUB: DESIGN OF HEAT TRANSFER EQUIPMENT
1.(a) Derive an expression for parallel and counter flow on a effectiveness method ?.
(b) Explain about cross flow heat exchanges ?.
2.(a) Derive an expression for overall heat transfer co efficient and pressure drop
in a condenser ?.
(b) Explain about extended fin surfaces of a LMTD correction factor ?.
3.(a) Explain about temperature distribution and heat flow in an evaporator of a
pressure drop in a
Evaporators ?.
(b) Describe the factors to be consider in the design of heat transfer equipment
of a correction factor?
4.(a) How many types of a design of a compressors of a equivalent shaft of a work?.
(b) Describe the factors affection total volumemetric efficiency of a compound
compression with inter
Cooling and rotary compressors surgings ?.
Expressions for u/ x, u/y with first order accurate. Express the second
order derivative
Term u/x and mixed derivative term u/xy in difference from with
second order
Accurate.
3.(a) Using finite volume method of a formation of basic rules for control
volume approach using
1D steady heat conduction equation without heat generation?.
(b) Briefly Explain about interface thermal conductivity?.
4.(a) Describe the 2 D steady heat conduction and un steady heat
conduction ?.
(b) Explain the 3 D steady heat conduction and u - steady heat
conduction ?.
5. A Thin plate is initially at a uniform temperature of 500c. At a certain time
of t = 1 sec the
Temperature at the east side of the plate is suddenly reduced to 3c. The
other surface is
Insulated. Using the implicit finite volume method in conjunction with a suitable
time step
Size to calculate the transient temperature distribution of the slab and
compare it with the
Analytical solution at time t = 100 sec. The date are: plate thickness L = 4 cm,
thermal conductive
k = 25 W/m / k and pc = 10 10 j/m/k.