Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Date:
Drawing Date:
Agency:
Location:
Jurisdiction:
Project Name:
Project ID #:
Designer:
Phase:
Sub-Phase:
BUILDING DESCRIPTION:
REVIEWED BY:
Comments:
This checklist provides plan reviewers with a consistent structure to follow in verifying code compliance. However, it does not
contain reference to all code sections and is not intended to limit review scope if non-compliant items are observed that are not
listed in this form. Designers may also benefit from its use, with those caveats in mind.
Instructions: Each item is followed with a code reference that correlates with 2012 NC codes. If the review results in code
compliance comments, most will be referenced on this checklist in the appropriate locations, by entering their numbers from the
accompanying review letter. The lack of an entry for any item on this form means either the plans were found to be compliant based
on just the detail present at this phase of design OR that particular code section was found to be not applicable. That can change
as the design progresses, or if previous plan details are altered.
ADMINISTRATION
New
Alteration
Addition
Complete construction documents
Plans are sealed
(NC Admin & Policies Code (NCACP), section 106.2)
System
ARCHITECTUAL DRAWINGS
Single Occupancy (302)
Mixed Occupancy (508)
100%
+%
+%
= %
Total
North
East
South
West
Conversion factor:
Additional Notes:
Additional Notes:
ft2
ft
conversion factor
x
x
ft
stories
ft2
ft
stories
Permitted types of construction
Compliance verified:
Additional Notes:
Single Occ.
Yes
Nonsep.
Additional Notes:
No
ft2
Allowed area
(fire area 1)
(fire area 2)
(fire area 3)
= 1.00
(fire area 4)
Additional Notes:
tabular area
= ft2
(Table 503)
Additional Notes:
ft2
ft2
= ft2
number of stories
(maximum 3)
MEZZANINES (505)
Area limitation (505.2)
Egress (505.3)
Openness (505.4)
Equipment platforms (505.5)
UNLIMITED AREA BUILDINGS (507)
FIRE PROTECTION
FIRE-RESISTANCE-RATED CONSTRUCTION (Tables 601 & 602 and Chapter 7)
Note: A numeric entry indicates required rating in hours. NC indicates noncombustible construction required
Construction classification (602)
Exterior walls
Interior elements
Roof
FIRE-RESISTANCE RATINGS AND FIRE TESTS (703)
Ratings / Combustibility (703.2, 703.4)
Alternative Methods (703.3, 720, 721)
BUILDING ELEMENTS (Table 601)
East
South
West
Bearing
Nonbearing
PLASTER (718)
Note: Compliance required based on Use Group as per NCBC, Section 803.9 and T803.9
Cabinets (905.7)
Dry standpipes (905.8)
Valve supervision (905.9)
Monitoring (907.6.5)
Acceptance (907.7)
Inspection/maintenance (907.8)
Floor Area
T 1004.1.1)
Sq.Ft./Person
(Occ. Load)
(If applicable)
Stairways
Exits Required
Exits Shown
10
Assembly (1028)
Bleachers (1028.1.1)
Egress Width (1028.6)
Scoping requirements (1103)
Signage (1110)
Performance requirements
Type of Class
(Chapter 32)
(Chapter 33)
Additions (3403)
Alterations (3404)
Repairs (3405,3407)
Fire escapes (3406)
Change of occupancy (3408)
Additional Notes:
Note: Request and verify that a COMcheck compliance report for the project is submitted for plan review. Check that the report
indicates compliance. Check that the plans and specifications match the inputs noted in the reports. Check that there are no obvious
omissions from the program inputs. Sections of the report include building, mechanical, electrical, and plumbing. Note that
COMcheckautomatically minimizes report content to match the elements actually present in the building and input into the program.
This facilitates plan review and field verification.
COMcheckcan be found at this link: http://www.energycodes.gov/comcheck/
MECHANICAL/PLUMBING/ELECTRICAL
Duct location
Additional Notes:
Additional Notes:
Emergency/Standby Power
(Chapter
27)
Additional Notes:
12
13
07-05)
11.7.5 (1613.7)
Seismic Ground Motion Values (1613.5)
05, 1613.5.6)
Other loads
Impact loads (1607.8)
(1607.7)
Strength (1604.2)
Serviceability (1604.3)
Deflection (1604.3.1)
Analysis (1604.4)
General Design
Load Test (1604.6, 1604.7)
Anchorage- Walls/Decks (1604.8)
Counteracting Structural Actions (1604.9)
Wind Seismic Detailing (1604.10)
This checklist is produced by the Evaluation Services Section in the Engineering Division of the NC Department of Insurance and is
based on the 2012 NC Building Code
14