Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
C02-112
TABLE OF CONTENTS
HTD7, HTD8, HTD9 DISC MOWERS
FEATURES AND BENEFITS
General ...............................................................................................................1
Cutterbed ............................................................................................................3
Mainframe...........................................................................................................6
Optional Kits (Field Installed)............................................................................11
SPECIFICATIONS
Specifications HTD7 ......................................................................................13
Specifications HTD8 ......................................................................................14
Specifications HTD9 ......................................................................................15
COMPETITIVE COMPARISONS
Competitive Comparisons HTD7...................................................................16
HTD8
The HTD8 is a 6 disc, 7 10 (2.38 m) cutting
width mower. A tractor with a minimum of 40 hp
(30 kW) is required to operate the mower. The
tractor needs to be equipped with an enclosed
cab, to protect the operator.
The mower
attaches to the tractor with a Category II threepoint hitch, and requires a single acting remote
valve, for lifting the mower into transport
position.
C2020
HTD9
The HTD9 is a 7 disc, 9 2 (2.79 m) cutting
width mower. A tractor with a minimum of 45 hp
(34 kW) is required to operate the mower. The
tractor needs to be equipped with an enclosed
cab, to protect the operator.
The mower
attaches to the tractor with a Category II threepoint hitch, and requires a single acting remote
valve, for lifting the mower into transport
position.
C2030
C2033
C2031
C2032
C2034
C2040
C2050
C2060
C2061
Sealed Modules
Inside the sealed modules are cut steel bevel
drive gears and sealed bearings.
The
cutterbars reversible, hex driveshafts provide
longer life and reduced operating cost. Each
cutterbar module consists of two main pieces,
the sealed gearbox housing, and the oval disc
that retains the knives.
C2080
C2090
Knives
The standard knife has a 12 degree pitch. For
tough conditions such as down crop, an 18
degree knife is available. The 18 degree knives
gives more lift to help pick up the crop for a
cleaner cut. This optional 18 degree knife takes
a little more horsepower to operate and is more
subject to damage in abusive conditions.
C2100
C2120
PTO Shaft
All units are equipped with a 6-spline, 540-rpm
PTO shaft with an overrunning clutch. The
overrunning clutch is designed to prevent
damage to the cutter bar, PTO shaft, and tractor
PTO clutch when the machine is being shut
down. It allows the cutter bar to coast to a stop
when the PTO is turned off.
C2120
Drive Belts
The cutterbar main drive gearbox is driven from
the PTO shaft by belts. The HTD7 has 3
matched HB Section belts, the HTD8 has 4
matched HB Section belts, and the HTD9 has
a 4-groove power banded belt to drive the
machine. The belts help to reduce the shock
load to the gearbox. The belts can easily be
maintained without removing the belt guard.
(Guard shown removed to view belts)
C2130
C2140
C2150
C2160
C2170
Transport Lock
The transport lock valve is used to hydraulically
lock the cutterbar in the raised position when
transporting, storing or working on the machine.
It stops the cutterbar from lowering if hydraulic
pressure is lost.
2180
Home Position
2190
Breakaway Position
2200
C2210
2220
10
C2230
C2240
11
12
SPECIFICATIONS
HTD7 DISC MOWER
MODEL ..........................................................................................HTD7 - 6 ft 8 in Disc Mower
DIMENSIONS & WEIGHT
Weight lb (kg) ...................................................................................................... 1165 (528.8)
CUTTERBED
Cutting Width ft (m) .................................................................................................. 6.7 (2.03)
Number of Discs.....................................................................................................................5
Number of Knives..............................................................................................10 (2 per disc)
Knife Lift, Standard Degrees ................................................................................................12
Knife Lift, Optional Degrees .................................................................................................18
Knife Circle Diameter IN (mm).................................................................................. 19.7(500)
Recommended Cutting Angle Degrees ...........................................................................0 to 6
Disc Speed rpm................................................................................................................3000
Tip Speed mph (km/hr).......................................................................................... 175.8 (289)
Knives .................................................................................................Swingaway, Reversible
Cutterbed Design .................................................................................... Horizontal Hex Shaft
Modular Gear Components
Flotation ...................................................................... Non-Adjustable Enclosed Float Spring
FRAME
Protection .......................................................................................Spring Loaded Breakaway
Heat Treated Skid Shoes .......................................................................................................5
Hydraulic Lift.............................................................................................................. Standard
DRIVE SYSTEM
PTO Speed rpm .................................................................................................................540
Drive Line .....................................................................................................Constant Velocity
Drive Protection.........................................................................................Overrunning Clutch
Gearcase Drive ..................................................................................... 3V HB Section Belts
TRACTOR REQUIREMENTS
Recommended Horsepower hp (kW) ........................................................................... 35 (26)
Tractor Type .................................................................................................. Equipped w/Cab
Hitch ............................................................................................. Category I or II Three Point
Hydraulics ................................................................................... Single Acting Remote Valve
Cutting Speed mph (km/hr) ................................................................................Up to 10 (7.5)
13
SPECIFICATIONS
HTD8 DISC MOWER
MODEL ........................................................................................HTD8 - 7 ft 10 in Disc Mower
DIMENSIONS & WEIGHT
Weight lb (kg) ......................................................................................................... 1340 (608)
CUTTERBED
Cutting Width ft (m) .................................................................................................. 7.8 (2.38)
Number of Discs.....................................................................................................................6
Number of Knives..............................................................................................12 (2 per disc)
Knife Lift, Standard Degrees ................................................................................................12
Knife Lift, Optional Degrees .................................................................................................18
Knife Circle Diameter IN (mm).................................................................................. 19.7(500)
Recommended Cutting Angle Degrees ...........................................................................0 to 6
Disc Speed rpm................................................................................................................3000
Tip Speed mph (km/hr).......................................................................................... 175.8 (289)
Knives .................................................................................................Swingaway, Reversible
Cutterbed Design .................................................................................... Horizontal Hex Shaft
Modular Gear Components
Flotation, Inner ............................................................ Non-Adjustable Enclosed Float Spring
Flotation, Outer....................................................................................Adjustable Float Spring
FRAME
Protection .......................................................................................Spring Loaded Breakaway
Heat Treated Skid Shoes .......................................................................................................6
Hydraulic Lift.............................................................................................................. Standard
DRIVE SYSTEM
PTO Speed rpm .................................................................................................................540
Drive Line .....................................................................................................Constant Velocity
Drive Protection.........................................................................................Overrunning Clutch
Gearcase Drive ........................................................................................4V B Section Belts
TRACTOR REQUIREMENTS
Recommended Horsepower hp (kW) ........................................................................... 40 (30)
Tractor Type .................................................................................................. Equipped w/Cab
Hitch ....................................................................................................Category II Three Point
Hydraulics ................................................................................... Single Acting Remote Valve
Cutting Speed mph (km/hr) ................................................................................Up to 10 (7.5)
14
SPECIFICATIONS
HTD9 DISC MOWER
MODEL ..........................................................................................HTD9 - 9 ft 2 in Disc Mower
DIMENSIONS & WEIGHT
Weight lb (kg) ......................................................................................................... 1340 (608)
CUTTERBED
Cutting Width in (mm)............................................................................................. 110 (2794)
Number of Discs.....................................................................................................................7
Number of Knives..............................................................................................14 (2 per disc)
Knife Lift, Standard Degrees ................................................................................................12
Knife Lift, Optional Degrees .................................................................................................18
Knife Circle Diameter in (mm) ................................................................................. 19.7 (500)
Recommended Cutting Angle Degrees ...........................................................................0 to 6
Disc Speed rpm................................................................................................................3000
Tip Speed mph (km/hr).......................................................................................... 175.8 (289)
Knives .................................................................................................Swingaway, Reversible
Cutterbed Design .................................................................................... Horizontal Hex Shaft
Modular Gear Components
Flotation, Inner ............................................................ Non-Adjustable Enclosed Float Spring
Flotation, Outer....................................................................................Adjustable Float Spring
FRAME
Protection .......................................................................................Spring Loaded Breakaway
Heat Treated Skid Shoes .......................................................................................................7
Hydraulic Lift.............................................................................................................. Standard
DRIVE SYSTEM
PTO Speed rpm .................................................................................................................540
Drive Line .....................................................................................................Constant Velocity
Drive Protection.........................................................................................Overrunning Clutch
Gearcase Drive ........................................................................................4V B Section Belts
TRACTOR REQUIREMENTS
Recommended Horsepower hp (kW) ........................................................................... 45 (34)
Tractor Type .................................................................................................. Equipped w/Cab
Hitch ....................................................................................................Category II Three Point
Hydraulics ................................................................................... Single Acting Remote Valve
Cutting Speed mph (km/hr) ................................................................................Up to 10 (7.5)
15
COMPETITIVE COMPARISONS
HTD7 DISC MOWER
MAKE
MODEL
TRACTOR REQUIREMENTS
PTO HP, Minimum hp (kW)
PTO Speed rpm
Three Point Hitch Category
WEIGHTS AND DIMENSIONS
Transport Width ft (m)
Weight lb (kg)
MOWER CAPACITY
Cutting Width ft (m)
Cutting Height in (mm)
DRIVES
Input to Gearcase
Protection
FLOTATION AND
TRANSPORT
Breakaway
Flotation
Transport System
Cylinder
Transport Lock
CUTTERBAR
Style
Drive System
Lubrication
Number of Discs
Number of Knives per Disc
Disc Speed rpm
Knife Tip Speed mph (kph)
OPTIONS
Challenger
HTD7
New Holland
615
JF
SB 2000
Kuhn
GMD 500
35 (26)
540
Category I or II
45 (34)
540
Category II
40 (230
540
Category II
35 (26)
540
Category I or II
INA
INA
IINA
1026 (465)
1275 (580)
10 (254) Plus
Tractor
920 (418)
860 (390)
6.7 (2.03)
1.5-3.25 (38-83)
6.8 (2.03)
1.1-3.5 (29-89)
6.7 (2.01)
1.5-2.5 (35-60)
6.6 (2.01)
1.1-2.0 (29-51)
3 HB V-Belt
Overrunning Clutch
Multi V-Belt
Overrunning Clutch
Multi V-Belt
INA
Multi V-Belt
Optional
Spring Loaded
Non-Adjustable
Hydraulic, Vertical
Fold
Single-Acting
Hydraulic
Spring Loaded
Non-Adjustable
Hydraulic, Vertical
Fold
Single-Acting
Mechanical
Spring Loaded
Non-Adjustable
Hydraulic, Vertical
Fold
Single-Acting
Hydraulic
Spring Loaded
Single Spring
Hydraulic, Vertical
Fold
Single-Acting
Mechanical
Individual Disc
Drive Modular
Components
Segmented Hex
Driveshafts
Grease
5
2
3000
176 (283)
Topping Skids,
Swathboard, Inner
Crop divider, Tall
Crop Divider, Offset
Hitch, Flotation
Spring Kit
Individual Disc
Drive Modular
Components
Individual Splined
Shafts
Oil
5
2
3000
176 (283)
Topping Skids, Left
Hand Swath Kit
Oil-Bath Gear
Cutterbed
Oil-Bath Gear
Cutterbed
16
Intermeshing Gears
Intermeshing Gears
Oil
5
2
INA
INA
Topping Skids,
Offset Hitch,
Overrun Clutch,
Left Swathboard,
Cat I Adapter,
Support Chain
Oil
5
2
INA
INA
Topping Skids,
Overrunning
Clutch, Mowing
Below Horiz. Kit
COMPETITIVE COMPARISONS
HTD7 DISC MOWER
MAKE
MODEL
TRACTOR REQUIREMENTS
PTO HP, Minimum hp (kW)
PTO Speed rpm
Three Point Hitch Category
WEIGHTS AND DIMENSIONS
Transport Width ft (m)
Weight lb (kg)
MOWER CAPACITY
Cutting Width ft (m)
Cutting Height in (mm)
DRIVES
Input to Gearcase
Protection
FLOTATION AND TRANSPORT
Breakaway
Flotation
Transport System
Cylinder
Transport Lock
CUTTERBAR
Style
Drive System
Lubrication
Number of Discs
Number of Knives per Disc
Disc Speed rpm
Knife Tip Speed mph (kph)
OPTIONS
Challenger
HTD7
Krone
AM 203 S
35 (26)
540
Category I or II
36 (27)
540
Category I or II
INA
1026 (465)
968 (440)
6.7 (2.03)
1.5-3.25 (38-83)
6.6 (2.00)
INA
3 HB V-Belt
Overrunning Clutch
Spring Loaded
Non-Adjustable
Hydraulic, Vertical Fold
Single-Acting
Hydraulic
Spring Loaded
Single Spring
Hydraulic, Vertical Fold
Single-Acting
Hydraulic
NA - Not Available
INA - Information Not Available
Every attempt has been made to ensure the accuracy, but AGCO assumes no responsibility for authenticity of data. Data
presented is obtained from various sources, including manufacturers publications.
17