Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
M-900+A
requirements.
Optional enhanced severe dust and liquid protection package with two-part epoxy paint for harsh environments.
High inertia mode software allows handling of very large parts with minimal cycletime penalty.
+ n t e l l i g e n t
R O B O T
s o l u t i o n s
M-900+A/200P DIMENSIONS:
M-900+A/350 grinding risers and heavy ash from ductile iron parts.
PAYLOAD: 200-700KG
M-900+A
M900+A/350
6
M900+A/260L
6
350
25
550
2650
+0.3
746
360
150
223
720
250
720
100
95
95
105
105
170
1960 (200)
1960 (200)
892 (91)
235 / 392
235 / 392
156 / 352
All Axes
1720
Floor, ceiling
& angle
260
25
550
3100
+0.3
746
360
150
211
720
250
720
100
105
95
120
120
200
1666 (170)
1666 (170)
715 (73)
188 / 313
188 / 313
117 /225
All Axes
1800
Floor, ceiling
& angle
J1
J2
J3
J4
J5
J6
Motion Speed
J1
(degrees/sec.)
J2
J3
J4
J5
J6
Wrist Moment N*m(kgf*m) J4
J5
J6
Wrist Inertia(1) kgm2
J4
J5
J6
Mechanical brakes
Mechanical weight (kg) (5)
Mounting Method (2)
Installation Environment
Ambient temperature C
Humidity
Vibration (m/s2)
IP Rating
M900+A/600
6
600 (std) /
700 (option)
25
550
2832
+0.3
814
360
154
160
720
244
720
80
80
80
100
100
160
3381 (345)
3381 (345)
1725 (176)
510 / 1097
510 / 1097
320 / 444
All Axes
2800
M900+A/400L
6
M900+A/200P
6
400
25
550
3625 (4)
+0.5
980
360
154
160
720
244
720
80
80
80
100
100
160
2744 (280)
2744 (280)
1725 (176)
510 / 1097
510 / 1097
320 / 444
All Axes
3150
200
25 (3)
3507
+0.3
1133
360
180
180
720
230
720
110
95
95
95
95
165
2200 (224)
2200 (224)
715 (73)
431
431
392
All Axes
2670
Floor
Floor
Rack
0 to 45
Normally: 75% or less
Short term (within a month): 95% or less
No condensation (No dew or frost allowed)
0.5G or less
Wrist & J3 arm IP67, driving unit of the body IP66,
main body IP54 (IP56 optional)
Notes:
(1) Allowable load inertia at wrist can be switched by software parameters; acc/dec are slightly longer but all other specications are unchanged.
(2) Motion range will be derated for angle mount.
(3) For M-900+A/200P Robot, wrist load + J3 arm load cannot exceed 200kg.
(4) When the reach is between 3136mm and 3350, CG of the workpiece should be within 30 degrees from the wrist downward direction. When the reach is over 3350mm, CG of the workpiece should be downward from the wrist.
(5) Without controller
FANUCROBOTICS.COM
1-800-+Q-ROBOT
FANUC ROBOTICS LITHO IN U.S.A. FRA - 10/10