Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
N-312
Rev.01 dd 23/02/2009
Page 1 of 5
0003/2008
rev.02 dd 10/05/2011
FLFE series
lighting fixtures
New
product:
FLFE-218
FLFE-236
FLFE-258
Marking
CE 0722:
1
II
10
1.
11
Ta spec. -20C+55C
12
CE mark means "European Conformity": the product fulfils all EU Directives requirements on safety, health,
consumer protection,...
2. Identification number of the notified board (CESI) that supervises production in compliance to 94/9/CE ATEX
Directive
3. Explosion Protection Marking
4. Apparatus Group II (surface equipment)
5. Category 2 (suitable for gas zone 1 and 2, dust zone 21 and 22)
6. Gas and Dust (suitable for both gas and dust zone)
7. Mode of protection (Ex de: explosion proof Ex d- with Ex e junction box; IIC: gas group; Ex tD A21: dust
protection)
8. IP mechanical protection degree
9. Temperature class
10. This is the max temperature that can be reached on the equipment hottest surface, while working
11. Ambient temperature allowed range
12. Extended ambient temperature allowed range (for special executions)
Ex Zone
ZONE 1; ZONE 21; ZONE 2; ZONE 22
Conformity to Standards
EN60079-0, EN60079-1, EN60079-7, EN61241-0, EN61241-1
Compliant to
ATEX 94/9/CE Directive
Mod.N-312
Rev.01 dd 23/02/2009
Page 2 of 5
Installation
Furthermore, due to their high mechanical robustness and to the Cortem exclusive paint
treatment, FLFE series fixtures are also suitable for:
Ta -20C +55C
Max. Surface Temp.
T80C
Normal service
Normal service +
emergency
Emergency only
(NP service)
Table A
Ta -20C +50C
Max. Surface Temp.
T75C
Plus
Mod.N-312
Rev.01 dd 23/02/2009
Page 3 of 5
Mod.N-312
Rev.01 dd 23/02/2009
Page 4 of 5
Cover
O-ring
Electrical equipment
Frame/reflector
Plug type PLG2IB
Fluorescent tubes
Connector
terminals L, N, Pe sez.4 mm
O-ring
Cover
Electrical features
- Suitable for no.2 fluorescent tubes
(18W,36W,58W)
- Nominal voltage 230VAC (110, 240, 277V
upon request)
- Nominal frequency: 50/60Hz
- Direct connection to terminal strip L, N, Pe
section 4mm2
- Bi-pin lamp-holder, type G13
- 4Ah or 7Ah, 6VDC rechargeable batteries
- Electronic Inverter 110/230VAC, 50/60Hz
- Electronic ballast 110/230VAC, 50/60Hz
- Signalling LED installed onto internal
frame, in order to verify batteries charge
current
- Internal wiring in silicone rubber, glass
fibre reinforced, cables.
- Possibility to loop-in / loop-out connection
between multiple installed fixtures (special
execution for FLFE with emergency
service)
- safety switch installed internally for fixture
in emergency service
Accessories
Cod.
M8
T
(Tige)
20
GOF-8
(Eyebolt)
140
10
10
G-244
(Bracket type U)
140
10
10
G-263
(Bracket type V)
10
G-258
(Bracket type D)
45
10
G-0480
(Pole bracket)
1 12"
40
100
Mechanical features
M8
Mod.N-312
Rev.01 dd 23/02/2009
Page 5 of 5
Models
Code
FLFE-218
FLFE-236
FLFE-258
FLFE-218EF
FLFE-236EF
FLFE-258EF
Watt
18
36
58
18
36
58
Service
Supply
Normal service
230VAC 50/60Hz
Normal service +
emergency
Market
Industry
o Mechanical and electrical engineering
o Onshore and Offshore Oil & Gas equipment
o Agro-food
o Distilleries
o Natural gas
o Pharmaceutical
o Explosives storage
In order to identify the desired model code, please check the General Catalogue, the
short-form Catalogue or Cortem web site.