Sei sulla pagina 1di 17

EM201 FLUID MECHANICS

LABORATORY REPORT 2

Lecturer / Tutor: Mr. Moorthy

Name

: LIM YING RAN

ID

: 1001334546

Course

: MECHANICAL ENGINEERING

FACULTY OF ENGINEERING, TECHNOLOGY & BUILD


ENVIRONMENT
UCSI UNIVERSITY
2015

EM201 Fluid Mechanics

Lab Report 2

Experiment 2 Head Loss in Pipe and Bends


Objective:
1. To determine the head loss in pipe flow for different diameters.
2. To estimate the friction factor for difference pipe diameters.
3. To determine the head losses in bends.

Learning Outcome:
Upon completion of the experiment, students should be should be able to determine
the head loss in pipe flow for different pipe diameters. Besides that, students are able
to plot the graph of friction factor against Reynolds number. Students should be able
to determine the head losses in each bend and find the pressure drop along the pipe.

Besides that, they should be able to plot the graph of

against

V
2g

to obtain

K for all the four bends.

Introduction:
In fluid dynamics, head is a concept that relates the energy in an
incompressible fluid to the height of an equivalent static column of that fluid. From
Bernoulli's Principle, the total energy at a given point in a fluid is the energy
associated with the movement of the fluid, plus energy from pressure in the fluid, plus
energy from the height of the fluid relative to an arbitrary datum. Head is expressed in
units of height such as meters or feet. To move a given volume of liquid through a
pipe requires a certain amount of energy. An energy or pressure difference must exist
to cause the liquid to move. A portion of that energy is lost to the resistance to flow.
This resistance to flow is called head loss due to friction.
Losses of head is also incurred by fluid mixing which occurs at fittings and by
frictional resistance at pipe wall. For a short pipe with numerous fittings, major part of
the head loss occurred because of the local mixing near the fittings. Where else for
long pipes, the surface friction at the pipe wall will predominate because of the length.

EM201 Fluid Mechanics

Lab Report 2

When a fluid flows through a pipe, the internal roughness of the pipe wall can
create local eddy currents within the fluid adding a resistance to flow of the fluid. The
velocity profile in a pipe will show that the fluid elements in the center of the pipe
will move at a higher speed than those closer to the wall. Therefore friction will occur
between layers within the fluid. This movement of fluid elements relative to each
other is associated with pressure drop, called frictional losses. Pipes with smooth
walls such as glass, copper, brass and polyethylene have only a small effect on the
frictional resistance. Pipes with less smooth walls such as concrete, cast iron and steel
will create larger eddy currents which will sometimes have a significant effect on the
frictional resistance. Rougher the inner wall of the pipe, more will be the pressure loss
due to friction. As the average velocity increases, pressure losses increase. Velocity is
directly related to flow rate:
v=

Q
A

Where Q is the volumetric flow rate and A is the cross-sectional are of the
pipe. Fluids with a high viscosity will flow more slowly and will generally not
support eddy currents and therefore the internal roughness of the pipe will have no
effect on the frictional resistance. This condition is known as laminar flow.
Laminar flow generally happens when dealing with small pipes, low flow
velocities and with highly viscous fluids. At low velocities fluids tend to flow without
lateral mixing,and adjacent layers slide past one another like playing cards. There are
neither cross currents nor eddies. Laminar flow can be regarded as a series of liquid
cylinders in the pipe, where the innermost parts flow the fastest, and the cylinder
touching the pipe isn't moving at all. In turbulent flow, the fluid moves erratically in
the form of cross currents and eddies. Turbulent flow happens in general at high flow
rates and with larger pipes.
For this experiment in part 2, the energy loss in pipe network with bends and
fittings has two components major loss due to shear stress between the water and the
pipe surface and minor loss, energy loss caused by sudden changes in either direction
or velocity as stated by Strothman (2006). Bends are provided in pipes to change the
direction of flow through it. An additional loss of head, apart from that due to fluid

EM201 Fluid Mechanics

Lab Report 2

friction, takes place in the course of flow through pipe bend. The fluid takes a curved
path while flowing through a pipe bend as shown in figure:

When a fluid flows in a curved path, there must be a force acting inwards on
the fluid to provide the inward centripetal acceleration. This result in an increase in
pressure near the outer wall of the bend, starting at some point A and rising to a
maximum at some point B. There also a reduction of pressure near the inner wall
giving a minimum pressure at C and a subsequent rise from C to D. Therefore
between A and B and between C and D the fluid experiences an adverse pressure
gradient which the pressure increases in the direction of flow. Fluid particles in this
region, because of their close proximity to the wall, have low velocities and cannot
overcome the adverse pressure gradient and this leads to separation of flow from the
boundary and consequent losses of energy in generating local eddies. Losses also take
place due to a secondary flow in the radial plane of the pipe because of a change in
pressure in the radial depth of the pipe. This flow, in conjunction with the main flow,
produces a typical spiral motion of the fluid which persists even for a downstream
distance of fifty times the pipe diameter from the central plane of the bend. This spiral
motion of the fluid increase the local flow velocity and the velocity gradient at the
pipe wall, and therefore results in a greater frictional loss of head than that which
occurs for the same rate if flow in a straight pipe of the same length and diameter.

Apparatus and Materials:


Hydraulic Bench, Losses in Bends Apparatus, Pipe Friction Apparatus, stopwatch.

EM201 Fluid Mechanics

Lab Report 2

Safety Precautions:
1. Make sure there are no air bubbles in the manometer before taking the
readings.
2. The readings on the manometer are taken when the flow rate is steady.
3. The eyes of the observer must be perpendicular to the readings to prevent
parallax errors.

Procedures:
Part A. Head loss in pipes of different diameters.
1.
2.
3.
4.

The LS-18001-15 Pipe Friction Apparatus is placed on the hydraulic bench.


The water inlet and outlet nipples are connected with flexible hoses.
The quick coupling is connected to the copper wire which has 11mm diameter.
The water pump is switched on and the overflow valve of the hydraulic bench

is closed slowly.
5. The valves at the copper pipe are opened and the air gap in the manometer is
removed by pressing the relief valve which is located on top of the manometer.
The water flow rate is measured using the flow meter on the hydraulic bench
and a stopwatch.
6. The reading at the manometer is recorded.
7. Steps 4 to 6 are repeated with different flow rates and the readings of the
manometer is taken.
8. Steps 3 to 7 are repeated for diameters of 8.3mm and 5.3mm.

EM201 Fluid Mechanics

Lab Report 2

Results:
Part A. Head loss in pipes of different diameters.
11mm
Flow rate, Q (Ls-1)
0.296
0.255
0.240
0.203
0.138
0.050

Height, h
(mm Hg)
35
29
22
15
8
3

8.3mm
Flow rate, Q (Ls-1)
0.289
0.243
0.208
0.196
0.141
0.088

Height, h
(mm Hg)
128
104
84
61
39
17

5.3mm

EM201 Fluid Mechanics

Flow rate, Q (Ls-1)


0.136
0.131
0.120
0.100
0.088
0.069
Calculations:

Lab Report 2

Height, h
(mm Hg)
278
236
204
161
123
75

Length of the pipe,

L=0.425 m

The Reynolds number for the pipe is calculated by the equation


=

VD
v

Where V
Coefficient

is the velocity,
of

D the diameter of the pipe.

kinematic

viscosity

of

the

fluid

at

25

C , v=9.04 107 m2 s1
The friction factor for the pipe is then calculated from the equation
f=

h
L v2

d 2g

Where h

is the difference of height of the manometer,

L , length of the pipe

v , velocity of the fluid

d , diameter of the pipe

g , gravitational acceleration

EM201 Fluid Mechanics

Flowrate,
Q

Lab Report 2

Velocity,
v (m/s)

Reynolds
number

h (m Hg)

Friction factor,
f

2.96

0.779

9479

0.035

0.029

2.55

0.671

8165

0.029

0.033

2.40

0.631

7678

0.022

0.028

2.03

0.534

6498

0.015

0.027

1.38

0.363

4417

0.0080

0.031

0.50

0.132

1606

0.0030

0.087

( 10-4 m3/s)

Table 1.1. Flow rate, velocity, reynolds number, head loss and friction factor for pipe
with diameter 11mm.

Flowrate,
Q

Velocity,
v (m/s)

Reynolds
number

h (m Hg)

Friction factor,
f

2.89

1.33

12248

0.128

0.028

2.43

1.12

10311

0.104

0.032

2.08

0.960

8814.0

0.0840

0.035

1.96

0.906

8318.0

0.0610

0.028

1.41

0.651

5977.0

0.0390

0.035

0.88

0.407

3737.0

0.0170

0.039

( 10-4 m3/s)

Table 1.2. Flow rate, velocity, reynolds number, head loss and friction factor for pipe
with diameter 8.3mm.

Flowrate,
Q

Velocity,
v (m/s)

Reynolds
number

h (m Hg)

Friction factor,
f

1.36

1.54

9035

0.278

0.029

1.31

1.48

8700

0.236

0.026

( 10-4 m3/s)

EM201 Fluid Mechanics

Lab Report 2

1.20

1.36

7973

0.204

0.027

0.990

1.12

6578

0.161

0.031

0.880

0.997

5845

0.123

0.030

0.690

0.782

4585

0.0750

0.030

Table 1.3. Flow rate, velocity, reynolds number, head loss and friction factor for pipe
with diameter 5.3mm.

Graph of f against Re for pipe with 11mm diameter

Graph of f against Re for pipe with 8.3mm diameter

EM201 Fluid Mechanics

Lab Report 2

Graph of f against Re for pipe with 5.3mm diameter

Procedures:
Part B. Head loss in bends
1. The inlet valve is connected to the hydraulic bench supply.
2. The inlet and outlet valves are fully opened and the water flow rate is
controlled from the hydraulic bench.
3. The flow rate of water is measured by using the flow meter on the hydraulic
bench and a stopwatch. The water flow rate is set to a suitable value.
4. After the flow rate is steady, the air relief valve which is located at the top of
the manometer is pressed if the water levels in the manometer are too low.
5. The water level of every tube in the manometer is recorded.
6. Steps 4 and 5 are repeated for different flow rates.

EM201 Fluid Mechanics

Lab Report 2

Results:
t(s)
Water Collected
(L)
Volumetric Flow
rate (Ls-1)
Velocity, v

24.8

27.94

38.98

41.88

0.202

0.179

0.128

0.119

0.922

0.817

0.584

0.543

555
509
450
420
334
263
185
50

465
435
395
375
320
275
224
137

397
377
350
335
297
270
235
177

360
346
326
315
289
269
245
217

-1

(ms )
Tube 1
Tube 2
Tube 3
Tube 4
Tube 7
Tube 8
Tube 9
Tube 10
Table 2.1

EM201 Fluid Mechanics

Lab Report 2

Calculations:
From the equation in part A, the Reynolds number can be calculated,
=

Given the diameter of the pipe,

VD
v

D is 16.7mm, v

Also given from the graph, the friction factor, f

Flowrate, Q

Velocity, v

7 2 1
is 9.04 10 m s

can be found.

( 10-4 m3/s)

(m/s)

Reynolds
number

2.02

0.922

17033

7.21 10

1.79

0.817

15093

7.40 103

1.28

0.584

10789

7.94 103

1.19

0.543

10032

8.06 103

Friction factor, f
3

Table 2.2. Value of flow rate, velocity, Reynolds number and friction factor.
Given

L=0.2907 m

d=0.0167 m

10

EM201 Fluid Mechanics

Lab Report 2

90 large radius bend


'

h =(tube 1tube 2)
Flow rate, (Ls-1)

h (m)

0.922
0.817
0.584
0.543

0.046
0.030
0.020
0.014

h f (m)
0.022
0.018
0.009
0.008

h (m)
0.024
0.012
0.011
0.006

Velocity head,
Flow rate, (L/s)

h (m)

V
2g

Lost Coefficient, K

0.922
0.817
0.584
0.543

0.024
0.012
0.011
0.006

0.043
0.034
0.017
0.015

0.558
0.353
0.647
0.400

90o small radius bend


'

h =(tube 3tube 4 )
Flow rate, (Ls-1)

h (m)

0.922
0.817
0.584
0.543

0.030
0.020
0.015
0.011

h f (m)
0.016
0.013
0.006
0.006

h (m)
0.014
0.007
0.009
0.005

Velocity head,
Flow rate, (L/s)

h (m)

V
2g

Lost Coefficient, K

0.922
0.817
0.584
0.543

0.014
0.007
0.009
0.005

0.043
0.034
0.017
0.015

0.326
0.206
0.529
0.333

11

EM201 Fluid Mechanics

Lab Report 2

90 elbow
'

h =(tube 7tube 8)
Flow rate, (Ls-1)

h (m)

0.922
0.817
0.584
0.543

0.051
0.045
0.027
0.020

h f (m)
0.010
0.008
0.004
0.004

h (m)
0.041
0.037
0.023
0.016

Velocity head,
Flow rate, (L/s)

h (m)

V
2g

Lost Coefficient, K

0.922
0.817
0.584
0.543

0.041
0.037
0.023
0.016

0.043
0.034
0.017
0.015

0.953
1.088
1.353
1.067

Two 45 bends
h' =(tube 9tube10)
Flow rate, (Ls-1)

h (m)

0.922
0.817
0.584
0.543

0.135
0.087
0.058
0.028

h f (m)
0.010
0.008
0.004
0.004

h (m)
0.125
0.079
0.054
0.024

Velocity head,
Flow rate, (L/s)

h (m)

V2
2g

Lost Coefficient, K

0.922
0.817
0.584
0.543

0.125
0.079
0.054
0.024

0.043
0.034
0.017
0.015

2.907
2.324
3.176
1.600

12

EM201 Fluid Mechanics

Lab Report 2

With reference from Table 2.2, the velocity head is calculated with
2
V 2 ( 0.922 )
=
=0.043
2 g 2 ( 9.81 )

The frictional head loss,

h f =4 f

L V2

d 2g

hf

is thus

4 ( 0.00721)

0.2907
0.043=0.022
0.0167

h =Piezometric head - h f , where the piezometric head is obtained from the


manometer readings.
Loss coefficient,
K=

h
V2
2g

0.024
0.043

0.558

Graph of h against /
90 Degree Large Radius Bend

Linear (90 Degree Large Radius Bend)

90 Degree Small Radius Bend

Linear (90 Degree Small Radius Bend)

90 Degree Elbow

Linear (90 Degree Elbow)

Two 45 Degree Bends

Linear (Two 45 Degree Bends)

13

EM201 Fluid Mechanics

Lab Report 2

Discussion:
With reference to Part A of this experiment, it is observed that the flow
velocity and head losses were higher as the diameter of the pipe decreases. In a
straight uniform pipe, there exists shear stress along the wall of the pipe and this
produces resistance to the flow. Generally, as the cross-sectional area increases in the
pipe, the flow rate of the fluid will decrease, the velocity is then reduced hence head
losses reduce also. Based on the graphs from Part A, as the Reynolds number
increases, the friction factor decreases. Reynolds number, a dimensionless parameter
can be used to determine the type of fluid flow. The fluid flow for all diameters are
turbulent flow in this experiment because the flow is laminar when Re < 2000 which has high
viscosity with low inertia, transient when 2000 < Re < 4000 and turbulent when Re > 4000.

On the other hand, results from Part B of the experiment shows head losses
occurs when fluids flow through different types of bends, too. Analyzing the graph of
h

against

V2
2g

for the four types of bends shows that generally when the

velocity increases, head loss due to bends increases also. We are able to interpret that
the head loss in the two 45
followed by the 90

bends is the highest among all the pipe bends,

elbow, 90

large radius bend and finally 90

small

radius bend.
Lastly, the accuracy of the results of this experiment can be increased if
parallax errors could be prevented when taking the readings. Most fluids are turbulent
flows and the viscosity of the fluid itself can affect the results of the experiment.

Conclusion:
In part A of this experiment, Reynolds number can be used to identify the type
of flow of the fluid, which is turbulent as all the data obtained showed Reyolds
number of higher than 4000. The higher the Reynolds number the lower the friction
14

EM201 Fluid Mechanics

Lab Report 2

factor. Part B of this experiment proves that head loss occurs when fluid flows
through bends. Different bends produced different pressure drops and through the
plotting of graphs, it is determined that the 90

small radius bend has the lowest

head loss for different flow rates.


Reference:

Douglas, J.F. Gasiorek, J.M and Swaffield, J.A. (2001) Fluid Mechanics.
4th ed. London: Prentice Hall.
Head Loss Darcy - Weisback Equation - Fluid Flow Hydraulic and Pneumatic,
Engineers Edge. 2015. Head Loss Darcy - Weisback Equation - Fluid Flow Hydraulic
and

Pneumatic,

Engineers

Edge.

[ONLINE]

Available

at:

http://www.engineersedge.com/fluid_flow/head_loss.htm. [Accessed 11 June 2015].


Losses

in

Pipes.

2015.

Losses

in

Pipes.

[ONLINE]

Available

at:

http://me.queensu.ca/People/Sellens/LossesinPipes.html. [Accessed 11 June 2015].


Reynolds

Number.

2015.

Reynolds

Number.

[ONLINE]

Available

https://www.grc.nasa.gov/www/BGH/reynolds.html. [Accessed 11 June 2015].

15

at:

Potrebbero piacerti anche