Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Home | Amtgard Rules & Documents | Arts & Sciences | Fighting Instruction | Links | Miklos Stats
This pages will take you through the basic steps of leather carving with the basic 7 tools:
Home
Basic Leathercrafting
Basic Leather Carving
Cutting Leather
Dying Leather
Edging Leather
Key LW Techniques
1. Swivel Knife
2. Camouflage Tool
3. Pear Shader Tool
4. Beveler Tool
5. Veiner Tool
Vortex
Cutting
Tools
For
woodworking,
plastic and
non- ferrous
industries.
6. Seeder Tool
7. Backgrounder Tool
This tutorial will take you through carving a basic design on a commercial pattern. The pattern used here is from the
excellent tutorial book The Leatherworking Manual and we highly recommend this book. This tutorial was adapted from
the material on www.craftcrave.com please visit them and consider buying your leatherworking accessories from them.
LEATHER PREPARATION
pdfcrowd.com
2. Prepare a pattern - Lay your tracing film atop your pattern (matte
side up) and trace the pattern as accurately as possible with a pencil.
If using a Craftaid, skip this step.
3. Position the pattern on the leather. Trace all the pattern lines with a
stylus using gentle pressure.
If using a craftaid, place it texture side down on the leather. Use a
spoon shaped modeling tool to burnish the back of the craftaid to
transfer the pattern.
4. You are now ready to start carving. Try to avoid letting the leather
dry out as repeated moistening and drying will make it harder to carve.
If you need to take a break place it in a ziplock bag. If the leather starts
to dry while working with it moisten again as needed. Please note: do
not store wet leather for more than a few hours this way, or it may get
moldy.
SWIVEL KNIFE
pdfcrowd.com
steel straight edge may be used as a guide. Take care not to over cut
at the corners.
7. Examine your pattern and photocarve. Determine which design
elements are in the foreground. Begin cutting the foremost objects
first.
CAMOUFLAGE TOOL
9. Also called Cams. Again practice on scrap before stamping your
project. The tool is positioned, then tapped with the mallet. Do not use
a metal hammer on leather stamps as this will ruin them. Study the
photocarve design. This tool can be used tilted left, right, forward,
backward, and vertical to achieve a variety of patterns.
10. On stems and scrolls, the tool is generally used along the lines. In
this process it is tilted towards the line. Note that each line of this stem
/ leaf has been done. A single stamp has also been done to the center
open in browser PRO version
pdfcrowd.com
of the scroll.
11. Cams are sometimes used to texture flower petals. When used for
petals, the tool is usually held vertically, but tilted slightly forward and
stamped progressively from the flower center outward.
12. The shader is used to contour flower petals and leaves. They are
available in a variety of shapes and patterns.
13. Shaders can be held at any angle needed. Tilt towards the narrow
end for tight areas. Hold vertically for larger areas.
pdfcrowd.com
BEVELER TOOL
16. The beveler is used to "raise" areas of the design imparting a 3
dimensional appearance. It accomplishes this by lowering the
surrounding area. Bevelers come in a variety of textures and sizes.
17. Hold the beveler vertical at all times. Note that the bottom is wedge
shaped - the deepest part of the wedge is always placed in the cut to
be beveled. Pay attention to which side of the line you are beveling - if
you bevel the wrong side it will lower the foremost object and ruin the
piece.
18. If the design has a border this is always beveled first. Next, bevel
the formost design elements. Work from foreground to background the
same as when you cut the design with your swivel knife.Take care that
the beveling is smooth and no tool marks are visible. Walking the
beveler along the cut will help keep it smooth.
19. On lines that were cut progressively shallower, the beveler is used
with progressively lighter taps to smooth the transition.
VEINER TOOL
open in browser PRO version
pdfcrowd.com
20. The veiner is generally used to pattern leaves, stems and scrolls.
They are available in a wide variety of sizes, patterns, and curvatures.
Usually used tipped to the left or right, it can also be used vertically.
22. As the stem narrows, more tilt is used. This allows the veiner to
make a narrower impression.
pdfcrowd.com
23. Be sure to change the angle of the tool as you go around curves
such as the ends of scrolls.
SEEDER TOOL
25. A single seed impression is usually used in the center of the scroll
ends.
26. Flower centers are made by first stamping seeder impressions
around the perimeter of the center.
pdfcrowd.com
BACKGROUNDER TOOL
pdfcrowd.com
DECORATIVE CUTS
32. Most beginners find this step the most difficult. Practice decorative
swivel knife cuts before proceeding.
33. Study your photocarve. Decorative cuts are generally made by
pulling the knife towards yourself.
34. Most decorative cuts start with a deep cut that gets progressively
lighter.
35. Make sure your cuts flow with the design.
Modeling Tool
36. Modeling tools, or modelers as they are often called are used for a
variety of things and accordingly come in a variety of shapes. For most
floral carving a dished spoon style is all that is needed.
pdfcrowd.com
37. Correct mistakes - If you have been sloppy with the stamping tools,
it is sometimes possible to burnish out the pattern with the spoon end
of the tool. Shown here is an overlapping beveler stamp onto the
border that can be smoothed with the modeler.
38. Although not essential, slightly rounding the edges of the design
elements will enhance their appearance. Take care not to round them
too much as this will reduce the effect of the beveling.
39. The design is now done and should be dyed and finished with your
choice of products following the manufacturer's directions.
pdfcrowd.com