Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
www.elsevier.com/locate/triboint
Abstract
One binary zinc-aluminium monotectoid and five ternary zinc-aluminium-copper alloys were produced by permanent mould
casting. Their wear properties were examined using a block-on-ring test machine. Hardness, tensile strength and percentage elongation of the alloys were also determined and microhardness of aluminium-rich a phase was measured.
It was observed that the hardness of the alloys increased continuously with increasing copper content up to 5%. Their tensile
strength also increased with increasing copper content up to 2%, but above this level the strength decreased as the copper content
increased further. Microhardness of the aluminium-rich a phase was also affected by the copper content in a manner similar to
that of the tensile strength. It was found that the wear loss of the alloys decreased with increasing copper content and reached a
minimum at 2% Cu for a sliding distance of 700 km. However, the coefficient of friction and temperature due to frictional heating
were found to be generally less for the copper containing alloys than the one without the element. The effect of copper on the
wear behaviour of the alloys was explained in terms of their microstructure, hardness, tensile strength, percentage elongation and
microhardness of the a phase.
2003 Elsevier Ltd. All rights reserved.
Keywords: Zinc-aluminium-copper alloys; Sliding wear; Mechanical properties; Microstructure
1. Introduction
The hardness and strength of binary zinc-aluminium
alloys are not adequate for most of the engineering applications, but they form the basis of a number of commercial alloys including ZAMAK, ALZEN and ZA families
[14]. These alloys are mainly based on zinc-aluminium
eutectic, eutectoid or monotectoid compositions. The
zinc-aluminium monotectoid alloys were found to have
higher strength and wear resistance than either eutectic
or eutectoid alloys [4,5]. It has been shown that the
addition of alloying elements including copper, silicon,
magnesium and nickel can improve the mechanical and
tribological properties of zinc-aluminium alloys [58].
Copper was found to be the most effective alloying
addition towards improving mechanical and tribological
Corresponding author. Tel.: +90 462 377 2919; fax: +90 462
325 5526.
E-mail address: savaskan@ktu.edu.tr (T. Savaskan).
0301-679X/$ - see front matter 2003 Elsevier Ltd. All rights reserved.
doi:10.1016/S0301-679X(03)00113-0
2. Experimental procedure
2.1. Preparation and testing of alloys
One binary Zn-40Al and five ternary Zn-40Al-1Cu,
Zn-40Al-2Cu, Zn-40Al-3Cu, Zn-40Al-4Cu, Zn-40Al5Cu alloys were produced from high purity zinc
(99.9%), commercially pure aluminium (99.7%) and
electrolytic copper (99.9%). The alloys were melted in
a crucible using an electrical furnace and poured at a
temperature of approximately 630 C into a steel mould
at room temperature. The moulds had a conical shape
46
force by the normal load. The temperature of the specimens was monitored during the tests by inserting a copper-nickel thermocouple in a hole made at a distance of
2 mm from the rubbing surface.
Each wear specimen was ultrasonically cleaned and
weighed before the wear test using a balance with an
accuracy of 0.01 mg. The ring was cleaned with
organic solvents to remove traces of oil or other surface
contaminants before each test. The sample was removed
after an interval of 20 h corresponding to a sliding distance of 140 km, cleaned in solvents and weighed to
determine the mass loss. This procedure was repeated
for each sample for 100 h, which corresponds to a total
sliding distance of 700 km. The measured values of mass
loss for all the specimens tested were converted into volume loss using the measured density of the alloys. The
wear surfaces of the samples tested for 100 h were examined using a scanning electron microscope (SEM) with
secondary electron emission mode.
3. Results
3.1. Chemical composition and microstructure
The chemical compositions and density of the alloys
are given in Table 1. It can be seen from this table that
the density of the alloys increased with the increasing
content of copper.
The microstructure of the Zn-40Al alloy consisted of
aluminium-rich a dendrites and interdendritic zinc-rich
h phases as shown in Fig. 2(a). Addition of copper
resulted in the formation of copper-rich intermetallic e
(CuZn4) phase in the interdendritic regions of the alloys.
This can be seen in the microstructures of the alloys containing 3 and 5% copper, Fig. 2(b) and (c). The number
and size of the e phase particles increased with the copper content of the alloys.
Table 1
Chemical compositions and density of the alloys
Alloy
Fig. 1.
Zn-40Al
Zn-40Al-1Cu
Zn-40Al-2Cu
Zn-40Al-3Cu
Zn-40Al-4Cu
Zn-40Al-5Cu
Zn
Al
Cu
59.4
59.7
55.8
56.7
56.0
55.2
40.6
39.2
42.2
40.4
40.1
39.9
1.1
2.0
2.9
3.9
4.9
Density
(kgm3)
4198
4213
4219
4274
4287
4318
47
Fig. 3. This figure also includes the plot of microhardness of a phase versus copper content of the alloys. It
can be seen from the figure that the macro hardness of
the alloys increased almost continuously with increasing
copper content. The tensile strength of the alloys also
increased with increasing copper content but only up to
2% above which the strength decreased as the copper
content increased. The trend shown by the microhardness of a phase was similar to that of the tensile strength
of the alloys.
4.1. Friction and wear test results
The friction coefficient of the alloys as a function of
sliding distance is shown in Fig. 4. It can be seen from
the figure that the friction coefficient of all the alloys
reached a steady state after showing a sharp decrease
during the initial sliding period. The plots of temperature
versus sliding distance were found to be similar to those
of the friction coefficient versus sliding distance for all
the alloys (Fig. 4). The friction coefficient obtained at
steady state reduced initially with increasing copper content, attained the minimum at 1% Cu, and then tended
to increase at still higher contents of copper (Fig. 3).
The plots of wear loss versus sliding distance for the
alloys are shown in Fig. 5. It can be seen from the figure
that the wear loss for most of the alloys increased with
sliding distance. The copper-free alloy was most sensitive to the changing distance. The wear loss of the copper containing alloys was less than that for the copperfree alloy in general. Moreover, the wear loss decreased
with increasing copper content attaining the minimum at
2% Cu.
Wear surfaces of the samples were characterised by
scratches, grooves and smearing as seen in Fig. 6(a)(c).
As the copper content increased, the scratches became
coarser but their number decreased.
5. Discussion
4. Mechanical properties
Variation of hardness, tensile strength and percentage
elongation of the alloys with copper content is shown in
48
Fig. 3. Effect of copper content on the microhardness of the a phase, and hardness, tensile strength, percentage elongation, friction coefficient
and wear loss of monotectoid-based Zn-Al-Cu alloys. The wear loss data were obtained after a sliding distance of 700 km.
Fig. 5. Plots of wear loss versus sliding distance for the alloys tested.
than the ideal can give rise to good smearing characteristics or even allow certain materials to act as solid lubricants [6,18]. The e phase which has a hexagonal crystal
structure acts as a load-bearing phase, produces hardening effects and offers wear resistance in the alloys
[9,11,19].
It was found that the hardness of the alloys increased
almost continuously with increasing copper content up
49
6. Conclusions
1. When the copper content reached 2%, copper-rich
intermetallic e phase formed in the interdendritic
regions of monotectoid-based zinc-aluminium-copper alloys.
2. Hardness of monotectoid-based zinc-aluminium-copper alloys increased continuously with increasing copper content. Microhardness of a phase and tensile
strength of the alloys also increased with increasing
copper content but only up to 2%, above which
they decreased.
3. The wear loss of monotectoid-based zinc-aluminiumcopper alloys decreased with increasing copper content up to 2%, above which the property showed an
increase. Therefore the highest strength and wear
resistance can be obtained with the monotectoidbased alloy containing 2% Cu.
4. The friction coefficient and temperature due to frictional heating were generally less for the copper containing alloys than the one without the element.
5. Tensile strength and hardness are very effective
towards controlling the wear behaviour of monotectoid-based zinc-aluminium-copper alloys, but
microhardness of a phase has the strongest influence
on their wear resistance.
6. Wear surfaces of monotectoid-based zinc-aluminiumcopper alloys were characterized by smearing and
scratches.
Fig. 6. Wear surfaces of Zn-40Al (a), Zn-40Al-3Cu (b) and Zn-40Al5Cu (c) alloys tested for a sliding distance of 700 km.
Acknowledgements
The authors would like to thank Dr. C. Duran for
chemical analysis of the alloys and all the technicians in
the Materials Division of the Mechanical Engineering
50
[15] Pandey JP, Prasad BK. Dry sliding wear behaviour of a zincbased alloy against different counterface materials. Z Metallkd
1997;88:73943.
[16] Prasad BK, Patwardhan AK, Yegneswaran AH. Microstructural
modifications through compositional alteration and their influence
on the mechanical and sliding wear properties of zinc-based
alloys. Scripta Materialia 1997;37(3):3238.
[17] Prasad BK, Patwardhan AK, Yegneswaran AH. Influence of aluminium content on the physical, mechanical and sliding wear
properties of zinc-based alloys. Z Metallkd 1997;88:3338.
[18] Prasad BK. Effects of partially substituting copper by silicon on
the physical, mechanical, and wear properties of a Zn-37.5 %Albased alloy. Materials Characterization 2000;44:3018.
[19] Prasad BK. Microstructure, mechanical properties and sliding
wear characteristics of Zn-based alloys: effects of partially substituting Cu by Si. Z Metallkd 1997;88:92933.
[20] Ashby MF, Jones DRH. Engineering Materials. England: Pergamon Press, 1983.
[21] Murphy S. Solid-phase reactions in the low-copper part of the
Al-Cu-Zn system. Zeitshrift Metallkunde 1980;71:96102.
[22] Savas kan T, Aydn M, Odabas oglu HA. Fatigue behaviour of
Zn-Al casting alloys. Materials Science and Technology
2001;17:6815.
[23] Savas kan T, Turhal MS , Murphy S. Effect of cooling rate on
structure and mechanical properties of monotectoid zinc-aluminium alloys. Materials Science and Technology 2003;19:67
74.
[24] Prasad BK, Patwardhan AK, Yegneswaran AH. Dry sliding wear
characteristics of some zinc-aluminium alloys: A comparative
study with a conventional bearing bronze at a slow speed. Wear
1996;199:14251.
[25] Pandey JP, Prasad BK, Yegneswaran AH. Dry sliding wear
behaviour of a zinc-based alloy: a comparative study with a
leaded-tin
bronze.
Materials
Transactions
(JIM)
1998;39(11):11215.
[26] Modi OP, Yadav RP, Prasad BK, Jha AK, Das S, Yegneswaran
AH. Microstructure and wear of zinc-aluminium alloys: influence
of secondary processing and alloy composition. Z Metallkd
1999;90:43943.
[27] Prasad BK. Tensile properties of some zinc-based alloys comprising 27.5%Al: effects of alloy microstructure, composition and
test conditions. Materials Science and Engineering A, 245;
1998;245:25766.
[28] Gahr KHZ. Microstructure and wear of materials. Oxford: Elsevier, 1987.
[29] Halling J. Principle of Tribology. Great Britain: Macmillan Education Ltd, 1989.