Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
RESTAURANT
INDICE
1.- ALCANCE..................................................................................................................................... 2
3.- PARAMETROS DE DISEO............................................................................................................ 2
4.- MATERIALES................................................................................................................................ 5
5 .- ESTRUCTURACION...................................................................................................................... 5
6.- COMBINACIONES DE CARGA..................................................................................................... 10
7.- CARGAS:................................................................................................................................... 11
8.- CARGAS PARA SISMO:............................................................................................................... 12
8.1.- CARGAS DE VIENTO............................................................................................................... 12
9.- RESULTADOS DEL ANALISIS:...................................................................................................... 13
9.1 DESPLAZAMIENTOS LATERALES DE LA ESTRUCTURA. (DISTORSONES).................................13
9.2 DEFLEXIONES EN VIGAS Y ARMADURAS................................................................................ 15
10.- DISEO:.................................................................................................................................. 17
10.1.- REVISION DE MUROS........................................................................................................ 17
10.2.- REVISION DE ARMADURAS DE ACERO...............................................................................25
10.3.- REVISION DE ZAPATAS...................................................................................................... 27
P a g e 1 | 33
1.- ALCANCE.
Se tiene planeado construir un edifico que tendr la funcin de Restaurant, adems de contar con un
rea de cocina.
La presente memoria revisara la cimentacin los muros y techo para las distintas cargas a las que
ser sometida la estructura, como cargas propias, cargas vivas, sismo, viento, cabe comentar que se
realiz un estudio de mecnica de suelos, en donde nos indica que tipo de cimentacin
recomendada.
LOCALIZACION:
P a g e 2 | 33
Uso: Comercial
Del programa prodisis de CFE, tenemos el coeficiente ssmico para el mtodo simplificado.
El coeficiente ssmico es de 0.30
Verificacin de requisitos de CFE, para validar que la estructura puede ser revisada con el mtodo de
diseo ssmico simplificado del manual CFE:
P a g e 4 | 33
4.- MATERIALES
5 .- ESTRUCTURACION
La estructura se plante por medio de muros de mampostera reforzada, y cubierta de losacero,
soportadas por armaduras de acero.
P a g e 5 | 33
P a g e 6 | 33
P a g e 7 | 33
P a g e 8 | 33
P a g e 9 | 33
Datos de Cargas
_________________________________________________________________________________________________________________________
NOMENCLATURA
Comb
Estados de carga
_________________________________________________________________________________________________________________________
Estado
Descripcin
Comb.
Categora
---------------------------------------------------------------------------------------------------------------------------------------------------------------CM
Carga Muerta
No
DL
CV
Carga viva
No
LL
SX
Sismo en X
No
EQ
SZ
Sismo en Z
No
EQ
VX
Viento en X
No
WIND
VZ
Viento en Z
No
WIND
D1
1.4CM
Si
D2
1.2CM+1.6CV
Si
D3
1.2CM+0.5VX
Si
D4
1.2CM+0.5VZ
Si
D5
1.2CM+VX
Si
D6
1.2CM+VZ
Si
D7
1.2CM+CV+VX
Si
D8
1.2CM+CV+VZ
Si
D9
1.2CM+SX
Si
D10
1.2CM+SZ
Si
D11
1.2CM+CV+SX
Si
D12
1.2CM+CV+SZ
Si
D13
0.9CM+VX
Si
D14
0.9CM+VZ
Si
D15
0.9CM+SX
Si
D16
0.9CM+SZ
Si
S1
CM
Si
S2
CM+CV
Si
S3
CM+0.75CV
Si
S4
CM+0.6VX
Si
S5
CM+0.6VZ
Si
S6
CM+0.7SX
Si
S7
CM+0.7SZ
Si
S8
CM+0.525SX
Si
S9
CM+0.525SZ
Si
S10
0.6CM+0.6VX
Si
S11
0.6CM+0.6VZ
Si
S12
0.6CM+0.7SX
Si
S13
0.6CM+0.7SZ
Si
RS1
1.1CM+1.1CV+SX+0.3SZ
Si
RS2
1.1CM+1.1CV+0.3SX+SZ
Si
RS3
1.1CM+1.1CV-SX-0.3SZ
Si
RS4
1.1CM+1.1CV-SX+0.3SZ
Si
id33
1.1CM+1.1CV+0.3SX-SZ
Si
----------------------------------------------------------------------------------------------------------------------------------------------------------------
P a g e 10 | 33
P a g e 11 | 33
7.- CARGAS:
Carga muerta
200 kg/m 2
10 kg/m 2
50 kg/m 2
Rellenos
50 kg/m 2
Instalaciones
30 kg/m 2
TOTAL
340 kg/m2
Ms peso propio de los elementos estructurales, que son considerados automticamente por el
programa.
Carga viva:
P a g e 12 | 33
CM+CV
(Kg/m2)
360.0
PESO
(T)
208
H (m)
3.8
FS (T)
45
P a g e 13 | 33
Analysis result
P a g e 14 | 33
P a g e 15 | 33
CH2M HILL
Current Date: 6/9/2015 2:49 PM
Units system: Metric
File name: C:\Users\baviles\Desktop\UTILERIAS\x fair\PAV\VRACRUZ\MODELOS\RESTAURANT CON AMPLIACION.etz\
Analysis result
Story drift nodes
_________________________________________________________________________________________________________________________
Amplification factor:
2.00
In X
Node
H
[m]
TX
[cm]
TX
[cm]
In Z
Drift
[cm]
Ratio
TZ
TZ
[cm]
[cm]
Drift
[cm]
Ratio
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SX = Sismo en X
429
5.45
0.03538
0.03538
0.07075
0.00013
0.00486
0.00486
0.00973
0.00002
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Sz = Sismo en Z
429
5.45
0.00524
0.00524
0.01049
0.00002
0.05731
0.05731
0.11463
0.00021
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Analysis result
Maximum relative deflections
_________________________________________________________________________________________________________________________
Remark.- Magnitude of deflections in absolute value.
CONDITION S2=CM+CV
Member
Defl. (2) [cm]
@(%)
@(%)
---------------------------------------------------------------------------------------------------------------------------------------463
0.06101 (L/2680)
50.00000
0.00000 (< L/10000) 100.00000
6
0.00780 (< L/10000)
25.00000
0.00000 (< L/10000) 100.00000
10
0.01967 (L/7624)
50.00000
0.01830 (L/8196)
62.50000
12
0.01005 (< L/10000)
25.00000
0.00000 (< L/10000) 100.00000
17
0.09615 (L/2439)
62.50000
0.00000 (< L/10000) 100.00000
19
0.06439 (L/2653)
25.00000
0.01695 (< L/10000)
62.50000
25
0.00238 (< L/10000)
25.00000
0.00000 (< L/10000) 100.00000
26
0.00566 (< L/10000)
75.00000
0.00000 (< L/10000) 100.00000
37
0.00517 (< L/10000)
37.50000
0.00000 (< L/10000) 100.00000
38
0.00449 (< L/10000)
62.50000
0.00000 (< L/10000) 100.00000
39
0.00244 (< L/10000)
25.00000
0.00000 (< L/10000) 100.00000
40
0.00661 (< L/10000)
50.00000
0.00000 (< L/10000) 100.00000
41
0.03541 (L/5768)
75.00000
0.00000 (< L/10000) 100.00000
104
0.03331 (L/5494)
62.50000
0.00000 (< L/10000) 100.00000
P a g e 16 | 33
108
110
115
122
123
134
135
136
138
158
159
163
164
167
169
179
180
181
185
186
187
235
237
239
242
245
262
0.02049
0.10321
0.03576
0.01113
0.01563
0.03038
0.04313
0.05583
0.00598
0.02798
0.03397
0.04745
0.02281
0.03329
0.04918
0.02407
0.02831
0.01124
0.03898
0.03436
0.04317
0.02308
0.08971
0.02151
0.00892
0.05569
0.04294
(L/7320)
(L/2199)
(L/6558)
(< L/10000)
(< L/10000)
(L/5085)
(L/3913)
(L/6045)
(< L/10000)
(L/5472)
(L/4812)
(L/3446)
(L/6713)
(L/4911)
(L/3324)
(L/6361)
(L/5410)
(< L/10000)
(L/3928)
(L/4457)
(L/3547)
(L/5904)
(L/1707)
(L/7118)
(< L/10000)
(L/3196)
(L/4146)
50.00000
50.00000
62.50000
62.50000
75.00000
50.00000
50.00000
75.00000
25.00000
50.00000
50.00000
50.00000
50.00000
50.00000
50.00000
50.00000
50.00000
37.50000
50.00000
50.00000
50.00000
50.00000
50.00000
62.50000
62.50000
37.50000
50.00000
0.00514
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00232
0.00232
0.00000
0.00232
0.00232
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
0.00000
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
(< L/10000)
62.50000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
50.00000
50.00000
100.00000
50.00000
50.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
100.00000
P a g e 17 | 33
10.- DISEO:
10.1.- REVISION DE MUROS
P a g e 18 | 33
CH2M HILL
Current Date: 6/9/2015 3:12 PM
Units system: Metric
Design Results
Masonry wall
_________________________________________________________________________________________________________________________
GENERAL INFORMATION:
Global status
OK
Design code
Geometry:
Total height
Total length
Base support type
Wall bottom restraint
Column bottom restraint
Rigidity elements
:
:
:
:
:
:
3.80 [m]
2.27 [m]
Continuous
Pinned
Pinned
None
Materials:
Material
Mortar type
Grouting type
Mortar bed type
Masonry compression strength (F`m)
Steel tension strength (fy)
Steel allowable tension strength (Fs)
Joint reinforcement allowable tension strength (Fs)
Steel elasticity modulus (Es)
Masonry elasticity modulus (Em)
Masonry unit weight
:
CMU 1.35-40
:
Port/Mort - M/S
:
Partial grouting
:
Full bed
: 0.0949139 [Ton/c...
: 2.81226 [Ton/cm2]
: 1.40613 [Ton/cm2]
:
2.1092 [Ton/cm2]
: 2038.89 [Ton/cm2]
: 85.4225 [Ton/cm2]
:
2.24257 [Ton/m3]
Number of stories:
Story
Story height
[m]
1
Wall thickness
[cm]
------------------------------------------------------------------------------------------------------------------1
3.80
19.38
1.42
------------------------------------------------------------------------------------------------------------------Load conditions:
ID
Comb.
Category
Description
-----------------------------------------------------------------------------------------------------------------------CM
No
DL
Carga Muerta
CV
No
LL
Carga Viva
SX
No
EQ
Sismo en X
Sz
No
EQ
Sismo en Z
Vx
No
WIND
Viento en x
Vz
No
WIND
Viento en z
D1
Yes
1.4CM
D2
Yes
1.2CM+1.6CV
D3
Yes
1.2CM+0.5Vx
D4
Yes
1.2CM+0.5Vz
D5
Yes
1.2CM+Vx
D6
Yes
1.2CM+Vz
D7
Yes
1.2CM+CV+Vx
D8
Yes
1.2CM+CV+Vz
D9
Yes
1.2CM+SX
P a g e 19 | 33
D10
D11
D12
D13
D14
D15
D16
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
1.2CM+Sz
1.2CM+CV+SX
1.2CM+CV+Sz
0.9CM+Vx
0.9CM+Vz
0.9CM+SX
0.9CM+Sz
CM
CM+CV
CM+0.75CV
CM+0.6Vx
CM+0.6Vz
CM+0.7SX
CM+0.7Sz
CM+0.525SX
CM+0.525Sz
0.6CM+0.6Vx
0.6CM+0.6Vz
0.6CM+0.7SX
0.6CM+0.7Sz
OK
P a g e 20 | 33
Geometry:
Segment
X Coordinate
[m]
Y Coordinate
[m]
Width
[m]
Height
[m]
----------------------------------------------------------------------------------------------------------------1
0.00
0.00
2.27
3.80
----------------------------------------------------------------------------------------------------------------Vertical reinforcement:
Segment
Bars
Spacing
[cm]
Ld
[cm]
------------------------------------------------------------------------------------------1
4-#4
61.00
45.65
------------------------------------------------------------------------------------------Results: Combined axial flexure
Segment
Condition
P
[Ton]
M
[Ton*m]
Ma
[Ton*m]
Ratio
----------------------------------------------------------------------------------------------------------------------------------------------------
P a g e 21 | 33
D12(Top)
-0.29
-0.30
0.57
0.53
Condition
P
[Ton]
Pa
[Ton]
Ratio
----------------------------------------------------------------------------------------------------------------------------------1
D12(Bottom)
10.91
52.34
0.21
Condition
ft
[Ton/cm2]
Fs
[Ton/cm2]
Ratio
----------------------------------------------------------------------------------------------------------------------------------1
D2(Top)
0.22
1.41
0.16
----------------------------------------------------------------------------------------------------------------------------------Results: Shear
Segment
Condition
fv
[Ton/cm2]
Fv
[Ton/cm2]
Ratio
----------------------------------------------------------------------------------------------------------------------------------1
D2(Top)
0.001
0.003
0.34
OK
P a g e 22 | 33
Geometry:
Segment
X Coordinate
[m]
Y Coordinate
[m]
Width
[m]
Height
[m]
----------------------------------------------------------------------------------------------------------------1
0.00
0.00
2.27
3.80
----------------------------------------------------------------------------------------------------------------Reinforcement:
Segment
Bars
Vertical reinforcement
Spacing
Ld
[cm]
[cm]
Horizontal reinforcement
Bars
Spacing
Ld
[cm]
[cm]
----------------------------------------------------------------------------------------------------------------------------------------1
4-#4
61.00
0.00
-0.00
0.00
----------------------------------------------------------------------------------------------------------------------------------------Results: Combined axial flexure
Segment
Condition
P
[Ton]
M
[Ton*m]
Ma
[Ton*m]
Ratio
----------------------------------------------------------------------------------------------------------------------------------------------------
P a g e 23 | 33
D2(Top)
-1.05
-3.46
5.00
0.69
Condition
P
[Ton]
Pa
[Ton]
Ratio
----------------------------------------------------------------------------------------------------------------------------------1
D12(Bottom)
10.91
53.58
0.20
Condition
ft
[Ton/cm2]
Fs
[Ton/cm2]
Ratio
----------------------------------------------------------------------------------------------------------------------------------1
D2(Top)
0.20
1.41
0.14
----------------------------------------------------------------------------------------------------------------------------------Results: Shear
Segment
Condition
fv
[Ton/cm2]
Fv
[Ton/cm2]
Ratio
----------------------------------------------------------------------------------------------------------------------------------1
D2(Top)
0.001
0.003
0.19
----------------------------------------------------------------------------------------------------------------------------------Notes:
* P = Axial load
* Pa = Allowable compressive force due to axial load.
* M = Moment at the section under consideration.
* Ma = Wall allowable moment due to axial force or lintel pure flexure allowable moment
* fa = Calculated compressive stress due to axial load only
* fb = Calculated compressive stress due to axial flexure only
* ft = Calculated axial tension
* Fa = Allowable compressive stress due to axial load only
* Fb = Allowable compressive stress due to axial flexure only
* fv = Calculated shear stress
P a g e 24 | 33
P a g e 25 | 33
P a g e 26 | 33
P a g e 27 | 33
Design Results
Reinforced Concrete Footings
_________________________________________________________________________________________________________________________
GENERAL INFORMATION:
Global status
Design Code
Footing type
Column type
:
:
:
:
OK
ACI 318-2011
Spread
Concrete
Geometry
P a g e 28 | 33
Length
Width
Thickness
Base depth
Base area
Footing volume
:
:
:
:
:
:
1.60 [m]
1.60 [m]
0.30 [m]
1.50 [m]
2.56 [m2]
0.77 [m3]
Column length
Column width
:
:
25.40 [cm]
25.40 [cm]
Materials
Concrete, f'c
Concrete type
Concrete elasticity modulus
Unit weight
:
:
:
:
Soil
Modulus of subgrade reaction
Unit weight (wet)
: 3150.00 [Ton/m3]
:
1.75 [Ton/m3]
0.25 [Ton/cm2]
Normal
219.36 [Ton/cm2]
2.40 [Ton/m3]
Centered
Steel, fy
Epoxy coated
Steel elasticity modulus
:
4.20 [Ton/cm2]
:
No
: 2038.89 [Ton/cm2]
P a g e 29 | 33
Footing reinforcement
Free cover
Maximum Rho/Rho balanced ratio
Bottom reinforcement // to L (xx)
Bottom reinforcement // to B (zz)
:
:
:
:
8.00 [cm]
0.75
5-#5 @ 36.00cm
5-#5 @ 36.00cm (Zone 1)
:
:
:
:
:
:
:
:
8-#3
2.50 [cm]
in tension
3
3
#3 @ 20.00cm
2
2
Node
Axial
[Ton]
Mxx
[Ton*m]
Mzz
[Ton*m]
Vx
[Ton]
Vz
[Ton]
--------------------------------------------------------------------------------------------------------------------------------------------CM
1
1
3.81
0.00
0.00
0.31
0.11
CV
1
1
0.15
0.00
0.00
0.03
0.03
Vx
1
1
0.00
0.00
0.00
0.00
0.00
Vz
1
1
0.00
0.00
0.00
0.00
0.00
SX
1
1
-1.66
0.00
0.00
-0.31
0.03
Sz
1
1
-0.01
0.00
0.00
0.00
0.25
_D1
1
1
5.34
0.00
0.00
0.43
0.16
_D2
1
1
4.82
0.00
0.00
0.42
0.18
_D3
1
1
4.57
0.00
0.00
0.37
0.13
_D4
1
1
4.57
0.00
0.00
0.37
0.13
_D5
1
1
4.57
0.00
0.00
0.37
0.13
_D6
1
1
4.57
0.00
0.00
0.37
0.13
_D7
1
1
4.73
0.00
0.00
0.40
0.16
_D8
1
1
4.73
0.00
0.00
0.40
0.16
_D9
1
1
2.91
0.00
0.00
0.06
0.17
P a g e 30 | 33
_D10
_D11
_D12
_D13
_D14
_D15
_D16
_S1
_S2
_S3
_S4
_S5
_S6
_S7
_S8
_S9
_S10
_S11
_S12
_S13
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4.56
3.06
4.71
3.43
3.43
1.76
3.42
3.81
3.96
3.93
3.81
3.81
2.64
3.80
2.94
3.80
2.29
2.29
1.12
2.28
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.37
0.09
0.40
0.28
0.28
-0.03
0.28
0.31
0.34
0.33
0.31
0.31
0.09
0.31
0.14
0.31
0.18
0.18
-0.03
0.18
0.38
0.20
0.41
0.10
0.10
0.14
0.35
0.11
0.14
0.13
0.11
0.11
0.14
0.29
0.13
0.24
0.07
0.07
0.09
0.24
--------------------------------------------------------------------------------------------------------------------------------------------RESULTS:
Status
OK
Soil.Foundation interaction
Allowable stress
Min. safety factor for sliding
Min. safety factor for overturning
:
:
:
1.5E04 [kg/m2]
1.25
1.25
Controlling condition
S2 - 1
Condition
Footing
qmean
[kg/m2]
qmax
[kg/m2]
max
[cm]
Area in compression
[m2]
(%)
Overturning
FSx
FSz
FS
slip
---------------------------------------------------------------------------------------------------------------------------------------------------------------------S2 - 1
4.37E03
4.58E03
0.145
2.56
100
215.37
87.40
44.54
----------------------------------------------------------------------------------------------------------------------------------------------------------------------
Bending
Factor
Min rebar ratio
:
:
Development length
Axis
Pos.
0.90
0.00200
ld
[cm]
lhd
[cm]
Dist1
[cm]
Dist2
[cm]
------------------------------------------------------------------------------------------------------------------------zz
Bot.
61.07
21.37
59.30
59.30
xx
Bot.
61.07
21.37
59.30
59.30
------------------------------------------------------------------------------------------------------------------------Axis
Pos.
Condition
Mu
Footing
[Ton*m]
*Mn
[Ton*m]
Asreq
[cm2]
Asprov
[cm2]
Asreq/Asprov
Mu/( *Mn)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------zz
Top
D1 - 1
0.00
0.00
0.00
0.00
0.000
0.000
zz
Bot.
D1 - 1
0.80
7.78
9.60
10.00
0.960
0.103
xx
Top
D1 - 1
0.00
0.00
0.00
0.00
0.000
0.000
xx
Bot.
D1 - 1
0.77
7.18
9.60
10.00
0.960
0.108
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
P a g e 31 | 33
Shear
Factor
Shear area (plane zz)
Shear area (plane xx)
Plane
:
:
:
0.75
0.34 [m2]
0.31 [m2]
Condition
Footing
Vu
[Ton]
Vc
[Ton]
Vu/( *Vn)
------------------------------------------------------------------------------------------------------------------------xy
D1 - 1
1.63
26.32
0.082
yz
D1 - 1
1.64
28.45
0.077
-------------------------------------------------------------------------------------------------------------------------
Punching shear
Perimeter of critical section (b...
Punching shear area
Column
:
:
1.83 [m]
0.37 [m2]
Condition
Footing
Vu
[Ton]
Vc
[Ton]
Vu/( *Vn)
------------------------------------------------------------------------------------------------------------------------column 1
D1 - 1
4.90
62.73
0.104
-------------------------------------------------------------------------------------------------------------------------
Notes
* Soil under the footing is considered elastic and homogeneous. A linear soil pressure variation is assumed.
* The required flexural reinforcement considers at least the minimum reinforcement
* The design bending moment is calculated at the critical sections located at the support faces
* Only rectangular footings with uniform sections and rectangular columns are considered.
* The nominal shear strength is calculated in critical sections located at a distance d from the support face
* The punching shear strength is calculated in a perimetral section located at a distance d/2 from the support faces
* Transverse reinforcement is not considered in footings
* Values shown in red are not in compliance with a provision of the code
*qprom = Mean compression pressure on soil.
*qmax = Maximum compression pressure on soil.
*max = maximum total settlement (considering an elastic soil modeled by the subgrade reaction modulus).
* Mn = Nominal moment strength.
* Mu/(*Mn) = Strength ratio.
* Vn = Nominal shear or punchure force (for footings Vn=Vc).
* Vu/(*Vn) = Shear or punching shear strength ratio.
P a g e 32 | 33