Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
INSTALLATION MANUAL
NOTE:
MINOR MODIFICATION
OF HELICOPTER BELLYPAN
REQUIRED! (Page 3 of 8)
Tyler Camera Systems 14218 Aetna Street Van Nuys, California 91401 USA
www.tylermount.com
800-390-6070
FSI - UltraMedia II
Operators Manual
FSI - UltraMedia RS
Operators Manual
MODEL:
A-S 350-355
JOB #:
REPORT #:
U.M. INST-001
DATE:
6/25/97
PREPARED BY:
# OF PAGES:
Chris Tyler
# OF DRAWINGS:
CHECKED BY:
George Wood
APPROVED BY:
REVISIONS
DATE
PAGES
AFFECTED
6/25/97
REVISION
LETTER
N/C
APPROVAL
Initial release.
11/2/99
ALL
10/2/00
8A
Mount Extension
Report # U.M.INST-001
BELLYPAN
BELLYPAN TEMPLATE
BELLYPAN (optional)
SUPPORT TUBE
SUPPORT TUBE
SKID-GEAR CLAMP (two pieces)
VIDEO GIMBAL
See: Setup Manual for particual Video Gimbal (UltraMedia II, RS, etc.)
i (ii)
Report # U.M.INST-001
LTH.
AN#
QTY.
USE
9/16-18
1/2-20
7/16-20
3/8-24
3/8-24
2.00
3.50
3.50
1.75
1.125
AN9-17A
AN8-33A
AN7-33A
AN6-16A
AN6-10A
2
8
2
4
4
MS NYLOCK NUMBERS
QTY.
3/8-24
7/16-20
1/2-20
9/16-18
8
2
8
2
MS21083N6
MS21083N7
MS21083N8
MS21083N9
A N WASHERS
3/8
7/16
1/2
9/16
AN960-616L(.032)
AN960-716L(.032)
AN960-816L(.032)
AN960-916(.062)
16
4
16
4
ii (ii)
Report # U.M.INST-001
AIRFRAME BRACKETS
ASSEMBLY INSTRUCTIONS
(Pages 2-4)
Page 1 of 9
Report # U.M.INST-001
Selection:
Airframe
counterweight. See:
Step 03
Picture:
Front left side
of helicopter
with bellypan
lowered.
Step
01/11
Unlatch, and lower the forward bellypan and verify wether or not their are
any slots in the forward corners of the bellypan (approx. 4 x 1 inches each).
Also, check to see if there is a hole near the rear of the left side (approx. 2 inches in diamater).
If Yes continue with step 03, if No continue with step 02.
Picture:
Close up of
Bellypan
Latch.
Note: Tylers Astar BELLYPAN, if used, may require adjusting the latches for proper fit.
Also see page 3 for specifics on the BELLYPAN.
Page 2 of 9
Report # U.M.INST-001
FRONT
(LEFT)
Picture:
Hand Saw
1-1/4 Hole Saw
2 Hole Saw
Step
02/11
Using the ASTAR BELLYPAN TEMPLATE & TOOLS, and following the additional instructions on the
template...
Mark and cut-out a slot to allow the AIRFRAME BRACKET to protrude.
Mark and cut-out a hole for routing the camera mount cables.
Note: Typically the slot and hole modification is only done to the left side (as shown). However, this
modification may also be done to the right side of the BELLYPAN (if necessary).
Page 3 of 9
Report # U.M.INST-001
Step
03/11
Pictures:
Airframe counterweight (left side).
Hardware:
(4) AN6-16ABOLTS
(8) AN960-616L WASHERS
(4) MS21083N6 NUTS
Attach and fasten one pair of the AIRFRAME BRACKETS around the airiframe counterweight
(Two bolts on each one).
Note: The brackets are labeled LEFT and RIGHT and must be attached accordingly.
Page 4 of 9
Report # U.M.INST-001
Picture:
Airframe counterweight (left side).
Hardware:
The original bolts,
washers and
nuts.
Page 4A of 9
Report # U.M.INST-001
Report # U.M.INST-001
Step
04/11
1.
Connect the two halfs of the Main Tube and fasten with L-Pin & Safety-Clip.
Page 5 of 9
Report # U.M.INST-001
Step
05/11
Insert 3/8 bolt and fasten lightly (to be fastened tightly later).
Page 6 of 9
Report # U.M.INST-001
Step
06/11
Install main tube, insert 3/8 bolt and fasten lightly (to be fastened tightly later).
Step
07/11
Slide front support bracket over tube, install in forward tang and tighten bolt.
Now, tighten bolts in steps 01/07 and 02/07.
Page 7 of 9
Report # U.M.INST-001
Step
08/11
Install Video Gimbal and insert 7/16 pin and safety clasp.
Step
09/11
Page 8 of 9
Report # U.M.INST-001
Step
10/11
Step
11/11
Route cable into helicopter through belly pan and secure cables as necessary.
Page 9 of 9