Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Instructions
0
/
I
wi
dt
h
med
ia
The power label and label liner rewinder includes a 120 VAC (or 220 VAC for Europe) to
12 VDC power supply. The rewinder has been
designed to work with desktop bar code printers.
Step
Place the rewinder on a flat surface. The reRewinder winder and printer both use separate external
Placement power supplies.
Do Not Apply Power to the Printer or Rewinder.
Verify that the power cords and supplies can be
placed and routed safely during use.
WARNING
980079-002 Rev.C
Remove
Shipping
Tape
/
I
wid
th
me
dia
Step
Tape
Rewind
Clip
Step
Place the printer on the rewinders printer pedOrienting the estal. Push the printer up against the stop.
Rewinder and
Printer
Printer Orientation
0
/
I
ia
wid
th
med
Printer
Stop
980079-002 Rev.C
Step
Plug in the printer and apply power to the
Load the printer only.
Printer
Load the printer with labels.
Step
Feed the label media until two (2) or more
Thread the inches of label liner reach beyond the label reLiner (and Labels) winder tube.
Adjusting Printer
Position To The
Label Stock
/
I
wid
th
med
ia
Slid
Ribs
980079-002 Rev.C
Step
Slide the rewind clip over the liner and on to
Lock the the label rewind tube. Fold the liner back toLiner/Labels wards the printer.
Securing The Liner
0
/
I
dia
wid
me
th
wid
th
me
dia
wid
th
me
dia
Step
While pressing the printers label feed button,
Hand Wind hand turn the label rewind tube. Turn the label
To Start liner from the top to the front, until it has comI
wid
dia
th
me
Hand Wind
Label Rewind Tube
980079-002 Rev.C
Step
Set the rewinders media selection switch to
Set Media match the width of the roll.
Selection Switch
Step
Applying
Rewinder
Power
Media Width
1 to 2 inches
2 to 3 inches
3 to 4 inches
I/
0
I/
0
N
wid
th
dia
Starting
the Rewinder
me
dia
wid
th
Power
Switch
NOTE
980079-002 Rev.C
Step
Press the printers feed button and re-adjust the
Rewinding printer and label liner to wind the liner straight.
Labels
Re-Adjusting
Printer Position
To The
Label Stock
0
/
I
wid
th
me
dia
For labels 2" or The rewinder includes two (2) snap-on media
wider: guides to help the labels roll straight. Usage of
these guides is optional, but recommended for
rewinding labels wider than two (2) inches.
NOTE
See Steps
through
for instructions.
980079-002 Rev.C
Step
Slide the media guides onto the rewind tube.
Add Media Guides The media guides will snap in for a snug fit.
0
/
I
wid
th
me
dia
Step
Slide the media guides gently into the label
Adjust liner.
Media Guides
0
/
I
dia
wid
th
980079-002 Rev.C
me
Step
Press the printers feed button or start printing
Fine Tune Label labels. Slide the printer from side to side, as reRoll Alignment quired, to square the label liner on the tubes
label roll. Slide the media guides into the label
liner to remove excess space and to square
them to the tube and label roll.
0
/
I
wid
th
me
dia
Step
Disconnect the power to stop label rewinding.
Removing The Slide the rewind clip out of the rewind tube and
Label Roll label roll. Remove the media guides. Slide the
label roll off the rewind tube.
Media Thickness
980079-002 Rev.C