Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
QUESTION BANK
UNIT I-BASICS OF OPERATIONAL AMPLIFIERS
PART-A
1. What is an integrated circuit?(A/M 2010)
2. What current mirror and its advantages?(A/M 2010)
3.Define slew rate and CMRR.(N/D 2010,A/M 2011,N/D 2011,A/M 2014)
4.Why are active loads preferred than passive loads in the input stage of the
amplifier?(N/D 2010)
5.Name the different methods used in the fabrication of integrated circuits.(A/M
2011,N/D 2012)
6.Define current mirror with magnification.(N/D 2011)
7.What are the two requirements to be met for a current source?(M/J 2012)
8.List the various methods of realizing high input resistance in a differential
amplifier?(M/J 2012)
9.What is the maximum undistorted amplitude, that a sine wave input of 10khz can
produce at the output of op-amp whose slew rate is 0.5V/s?(N/D 2012)
10.State the limitations of discrete circuits.(M/J 2013)
11.Why do we use aluminum for metallization?(M/J 2013)
12.State the advantages of integrated circuits over discrete components.(N/D
2013,A/M 2014)
13.Define offset voltage of an operational amplifier.(N/D 2013)
14.What are the applications of current source?
15.Define voltage references and voltage regulator.
16.What is an line regulation?
17.What is an load regulation?
18.Define Ripple Rejection Ratio(RRR)
PART-B
1.Define CMRR.Draw thecircuit of an OP-AMP differential amplifier and give the
expression for CMRR.(8)(A/M 2010)
2.Define slew rate.Explain the cause of slew rate and derive for slew rate of an opamp voltage follower.(8)(A/M 2010)
3.Draw the circuit diagram of the output stage of the IC741 OPAMP and explain its
operation with clearly indicating the protection mechanisms indicated.(16)(N/D
2010)
4.With a neat circuit diagram and with necessary equations explain the concept of
widlar current source used in op-amp circuit.(10)(A/M 2011,N/D 2011)
5.For the non-inverting op-amp shown in fig below,find the output voltage V0. (6)
(A/M 2011,N/D 2011)
PART-b
1.Desgin a first order low-pass filter for cut-off frequency of 2KHZ and pass band of
2.(8)(A/M 2010)
2.Explain a positive clipper circuit using op-amp and diode with neat diagrams.(8)
(A/M 2010)
3.Draw and explain a simple op-amp differentiator. Mention its limitations.Explain
with a neat diagram how it can be overcome in practical differentiator.(8)(A/M
2010,M/J 2012)
4.With relevant circuits,explain the following applications of OPAMP.(16)(N/D 2010)
(i) Voltage to current converters.
(ii) Multiplier
5.Explain the steps involved in the design of a bandpass filter using OPAMP.(8)(N/D
2011)
6.Write a note on Schmitt trigger. (8)(N/D 2011,N/D 2013,M/J 2012)
7.With neat circuit diagramand mathematical expressions,explain the operation of
the following op-amp applications.
(i) Scale changer (ii)Voltage follower (iii)Non-inverting adder (iv)Integrator
(A/M 2011,N/D 2012)
(16)
8.With the help of circuits and necessary operations explain log and antilog
computations are performed using IC 741.(16)(A/M 2011,N/D 2012,A/M 2014)
9.Explain the working of Instrumentation amplifier (8).(N/D 2013,M/J 2013,N/D
2011)
10.Explain the working of (i)Precision Full wave rectifier (ii) Integrator (16).(N/D
2013)
11. Draw and explain the circuit of a voltage to current converter if the load is
(i)Floating (ii)Grounded (8)(M/J 2012)
12.Design a OP-AMP based second order low-pass filter for cut-off frequency of
2KHZ 8)(M/J 2012,N/D 2011)
13.With neat diagram explain the applications of op-amp as precision
rectifier,clipper and clamper.(16)(A/M 2014)
PART-b
1.Wih a neat diagram explain the variable transconductance technique in analog
multiplier and give its output equation.(8)(A/M 2010,A/M 2013)
2.Briefly explain the working of voltage controlled oscillator.equation.(8)(A/M 2010)
3.What are the important building block of phase locked loop(PLL)explain its
working?(16)(A/M 2010,N/D 2013)
4. Draw the block diagram of VCO and explain its operation.Also derive the
frequency of oscillator.(10)(A/M 2011,N/D 2010,N/D 2012)
5.Draw the circuit of a PLL used as AM detector,FM dectector and frequency
synthesizer and explain its operation.(16) (A/M 2011,M/J 2012,A/M 2014,N/D
2012)
6.List and define the various performance parameters of a multiplier IC(6)(M/J 2012)
(6)(N/D 2011)
the
PART-B
1.Explain the working of R-2R ladder DAC.(8).(A/M 2010,A/M 2011,(M/J 2012,(A/M
2014,(N/D 2012),(N/D 2013)
2.What is a sample and hold circuit?Briefly explain its construction and application.
(8).(A/M 2010,(N/D 2010)
3.Explain the working of successive approximation ADC.(8).(A/M 2010,.(A/M
2011,N/D 2010),(N/D 2012)(N/D 2013)
4.Explain the operation of a weighted resistor type D/A converter.(8).(A/M 2011,
(A/M 2014),(N/D 2012)(N/D 2013)
5.Explain the oversampling A/D converter with functional block diagram.(8).(A/M
2011),(N/D 2012)
6.With neat circuit diagram and waveform of output explain the working of dual
slope A/D converter.(10)(M/J 2012,M/J 2013,N/D 2010)(N/D 2013)
7.Draw the block diagram and explain the working of
(16)(M/J 2013)
PART-B
1.HOow is voltage regulators classified?Explain a series voltage regulator.(8)(A/M
2010)