Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
LA4440
Monolithic Linear IC
http://onsemi.com
Package Dimensions
unit : mm
Specifications
Absolute Maximum Ratings at Ta = 25C
Parameter
Symbol
Conditions
Ratings
unit
VCC max1
VCC max2
Quiescent (t=30s)
25
Operating
18
VCC (surge)
t 0.2s
50
Pd max
15
Thermal resistance
j-c
Junction-to-case
C/W
Operating temperature
Topr
20 to +75
Storage temperature
Tstg
40 to +150
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
Symbol
Conditions
VCC
RL
Ratings
unit
13.2
Stereo
2 to8
Bridge
4 to 8
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
ORDERING INFORMATION
See detailed ordering and shipping information on page 13 of this data sheet.
Semiconductor Components Industries, LLC, 2013
July, 2013
21500TH(KT)/90196RM/33194HO/8064KI/3233KI/O070KI,TS No.750-1/13
LA4440
Operating Characteristics at Ta = 25C, VCC=13.2V, RL=4, f=1kHz, Rg=600, with 1001001.5mm3 Al fin,
See specified Test Circuit.
Parameter
Symbol
Quiescent current
Icco
Voltage gain
VG
Output power
Total harmonic distortion
Input resistance
PO
THD
Conditions
THD=10%, Stereo
Ratings
min
VNO
Rr
Ch sep
Muting attenuation
ATT
VG
Unit
max
100
200
mA
49.5
51.5
53.5
dB
5.0
6.0
19
THD=10%, Bridge
PO=1W
0.1
ri
typ
1.0
30k
Rg=0
0.6
1.0
mV
Rg=10k
1.0
2.0
mV
46
dB
55
dB
VO=0dBm, VM=9V
45
40
dB
2
dB
No.7502/13
LA4440
Sample Application Circuit 1. Stereo use
No.7503/13
LA4440
Sample Application Circuit 3. Bridge amplifier 2
No.7504/13
LA4440
Voltage Gain Adjust at Stereo Mode
VG
(dB)
RNF
Rf
(dB)
RNF+RNF
Rf
+ 6dB
RNF+RNF
Rf
VG=20log R +R (dB)
NF
NF
2
where (RNF+RNF) << R5
From this formula, it is seen that connecting RNF
causes the voltage gain to be reduced at the modes of
both stereo amplifier and bridge amplifier.
No.7505/13
LA4440
(g) In case of applying audio muting in each application circuit, the following circuit is used.
6VVMVCC
Recommended VM=9V
ATT=40dB (Rg=600)
VM VBE
RO
In case of increasing the muting attenuation, resistor 5.6k is connected in series with the input, and then the
attenuation is made to be 55dB. Be careful that connecting an input capacitor causes pop noise to be increased at
the time of application of AC muting. Increased RO, CO make it possible to reduce the noise. In case of completely cutting off power IC, pin (5) is grounded, and then DC control is available and the attenuation is made to
be .
Stereo
: 20R100
Bridge No.1 : 20R100
Bridge No. 2 : 0R50
10
11
12
13
14
Function pin
CH1
NF
CH1
NF
Pre
GND
AC
Audio
Muting
DC
CH2
IN
CH2
NF
CH2
Power
GND
CH2
BS
CH2
OUT
VCC
CH1
OUT
CH1
BS
CH1
Power
GND
Pin Voltage at
quiescent mode
1.4
0.03
13.0
0.03
1.4
11.9
6.8
13.2
6.8
11.9
No.7506/13
LA4440
Characteristics at stereo amplifier mode
No.7507/13
LA4440
No.7508/13
LA4440
No.7509/13
LA4440
No.75010/13
LA4440
Characteristics at bridge amplifier mode No. 2
No.75011/13
LA4440
3. The screw to be used must have a head equivalent to the one of truss machine screw or binder machine screw defined
by JIS. Washers must be also used to protect the IC case.
4. No foreign matter such as cutting particles shall exist between heat sink and radiator fin. When applying grease on the
junction surface, it must be applied uniformly on the whole surface.
5. IC lead pins are soldered to the printed circuit board after the radiator fin is mounted on the IC.
No.75012/13
LA4440
ORDERING INFORMATION
Device
LA4440J-K-E
Package
SIP14H
(Pb-Free)
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLCs product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts.
SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any
such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.750-13/13