Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
INTRODUCTION
UNIT-I
Why Alternatives?
4 to 5 million houses have to be built every year in India to wipe out the housing shortage
Majority of these houses would have to be build either in rural areas or for the
rehabilitation of slum dwellers
The gradual increase in the fuel prices
For instance a brick house of 50sq-m plinth area will consumes 5 to 6 tons of firewood
for the burning operation
To meet the demand without environmental degradation and over exploitation of natural
resources, alternative building materials are needed
SMB , hollow clay blocks, stone masonry blocks etc. are the alternative blocks which
substitute for the conventional blocks
Adoption of the alternate building blocks walling technology of construction results in
considerable amount of saving in walling cost of any type of building against
conventional blocks
Hence, this adoption of alternative building technology and alternative building materials
is best suited for developing countries.
Page 1
The primary use of energy in building materials I in the production of the building material.
For instance, bricks and tiles are produced by brining coal or firewood in kilns. Cement and lime
are again produced by heating clay and limestone using coal. Steel is also produced by using
coking coal as the fuel. In all these cases, the basic energy use in the form of thermal energy.
However, many materials also need mechanical processing through electrical energy. For
instance, pugging of clay bricks may use electricity. Grinding of raw materials and clinker in the
case of cement needs electricity.
Some materials like sand, essentially need transportation energy for procurement at site
DSCE
Page 2
Building blocks used for wall construction constitute a significant component of embodied energy
in a building. This is due to the fact that walls represent the largest volume component in a
building.
The stabilized mud Block (SMB) is produced by pressing a mixture of soil, sand and cement in a
machine. The example uses 6% cement stabilization. The Hollow Concrete Block had 7% cement
in the mixture. The steam cured block is made by pressing lime, soil and fly ash mixture and
curing in a steam chamber. Lime percentage is 10% of soil and fly ash.
Energy in Building
The total embodied energy in a building depends on the type of technologies used like RC
framed structure construction with brick in-fill walls, RC roof, Load bearing walls, Mosaic floors
etc.
Firstly, a particular building material can lead to a local environmental impact either in the
form of pollution/health or in the depletion of natural resources.
Secondly, building materials production using fossil fuel energies can cause global
environmental problems like global warming.
1. Stone
Size stone is often used for foundations and walls. Crushed stone aggregate is widely
Considerable amount of fine granite dust is generated at the site of stone extraction
The stone workers often inhale the fine dust and succumb to silicosis or tuberculosis after
Page 3
The top soil is often used for brick making, especially in the Indogangetic plains.
It is well known that the top soil is a rich source of nutrients for trees and crops and this
nutrient base is depleted by large scale brick manufacture near metropolitan cities.
2. Mangalore Tile
The extensive use of firewood for making Mangalore tiles in Coastal India has led to
deforestation in the Coastal regions.
Many a time, attempts are made to replace timber by concrete or Ferro cement.
Cement based materials cause depletion of fossil fuels and excessive carbon emissions
leading to global warming. Use of timber also alleviates global warming since the carbon in
timber is stored for a long period.
Thus, timber is a very environment friendly material, provided it can be procured without
disturbing natural forests.
Global Warming
DSCE
Page 4
The utilization of fossil fuels like coal and petroleum has been increasing steadily for more than
200 years, carbon-di-oxide in the atmosphere which was about 280 ppm at the beginning of the
Industrial Revolution, has now reached levels like 354 ppm.
The importance of buildings in the energy scenario can be understood by the fact that in the
European Union 40% of the total energy consumption is accounted for by buildings sector.
It is hence essential to explore Energy Efficient Building Alternatives. Here again, two
categories of energy efficiency need to be recognized. Firstly, the embodied energy in a building
needs to be reduced. Secondly, the energy used during the operational life of a building should be
reduced.
A building consumes far more energy during its life time than what is spent during its
construction.
Recent trends in air conditioning buildings in India can exacerbate the situation since most of the
buildings are poorly insulated and guzzle lot of energy to maintain thermal comfort.
Use of Solar Passive cooling concepts and improved thermal insulation are needed to mitigate
these problems.
A brick vaulted building with simple Solar Passive Cooling concepts was built in a village near
Bangalore showed significant improvements in indoor climate with marginal cost.
It is perfectly feasible to build 4 to 6 storeyed than masonry buildings using bricks/blocks with
strengths in the range of 8.0 to 20.0 MPa.
Hollow-Concrete Blocks or Stabilized Mud Blocks of 8.0 MPa strength can be easily obtained
with technologies available in India.
Thus a switch over to masonry of moderate rise (4 to 6 storeys) can save 30.0 to 40% of the
embodied energy.
ENVIRNOMENTAL
FRIENDLY
AND
COST
EFFECTIVE
BUILDING
TECHNOLOGIES
Role of Transportation in Buildings
DSCE
Page 5
Transportation of building materials to the construction site contributes to the cost and embodied
energy of a building. Greater the distance of transportation, greater is the consumption of energy
and money.
An example, one can explore the issue of sand for building mortars. The city of Bangalore has
exhausted nearby sources of sand and it has to be imported from distances of more than 100 km.
Extraction of san from remote villages is also leading to rapid deterioration of roads and erosion
of river banks due to loss of protective sand cover.
In this context, if sandy soils are available locally, stabilization of the soil by lime and cement can
easily produce a mortar with a short term strength of 2.0 MPa.
Use of stones (size stones or random rubble) is quite common in South India for foundations of
walls.
Wall construction can be cost effective, if the finish of the masonry unit is so good as to eliminate
plastering.
There is often a tendency to reduce the thickness of the wall, especially in framed structures, to
achieve cost reduction.
It must be noted that a wall thickness which is less than 225 mm can lead to penetration of heat,
especially from East and West facing walls.
The marginal reduction in cost is then accompanied by significant thermal discomfort in the
interior.
Increased use of fans and coolers will also lead to greater energy consumption throughout the lie
of the building.
DSCE
Page 6
This will also permit combination of two or three different materials for cost and energy
economy. For instance, in a Jack Arch Roofing, expensive concrete is partially replaced by brick
masonry.
Use of filler slabs, where the tension zone concrete is partly replaced by SMB or brick is also cost
and energy efficient.
Use of brick domes and vaults can lead to roofing systems which reduce penetration of solar heat
into the building.
The choice of building technologies/materials depends on the climate context. For instance, hot
summer and cold winter occurs in most of North India and the buildings should use cooling
techniques in summer while retaking the heat in Winter.
Well insulated buildings are needed here. In the case of hot and Humid environment, air
circulation becomes important to eliminate the discomfort due to humidity. In situations like cool
summer and very cold winter, where the Winter is very Cold (like in Ladakh and Sub-Himalayan
Regions), use of Winter heating using Solar Energy becomes important. Concepts like Trombe
Walls which use double glazing on the Southern Walls to capture Solar heat are useful.
Use of stone, soil in place of cement mortar going for roofs out of Mangalore tiles instead of
using concrete are the basic materials of construction.
DSCE
Page 7
The use of conventional methods consumes energy less as the locally available material is used so
it saves on the time and energy on transportation.
Lime used to be final coat of paint unlike todays chemical constituent matrix in the paint.
BUILDING BLOCKS
UNIT-II
INTRODUCTION
DSCE
Masonry may be defined as a well element made by holding strong blocks together with the help
of mortar.
The blocks are usually strong in compression. Such blocks may also be referred to as masonry
units. A wide variety of materials have been used for masonry.
Use of sun dried mud, stone and burnt brick have been known since ancient times. Laterite has
also been used for wall construction in specific locations where it is available.
New materials have merged in recent times for use as masonry units. Concrete block, Hollow
bunt clay block, Stabilization mud block and stone masonry block are some of the new
alternatives.
They are igneous, sedimentary and metamorphic stones. Examples for igneous stones are granite
and basalt, examples for sedimentary stones are limestone and sandstone and examples for
metamorphic stones are marble and gneiss.
Granite has highest strength, fine grained stones are stronger than the coarse grained stones.
Metamorphic rocks like gneiss shows lower strength if the loading is perpendicular.
Strength of the granite is known for its durability. Sand stone and basalt are less durable they do
not deteriorate in time spans of the order a couple of centuries.
Laterite which is found in coastal Karnataka is an interesting building material. It is used in Bidar
region extensively.
However, when Laterite blocks of more than 190mm is used, it is possible to use blocks of
strength 2.0 2.5 MPa.
DSCE
Generally, blocks of strength much lower than 2.0 MPa is desirable to avoid.
TYPE
Granite
65-228
Page 9
70-180
Limestone
70-100
Sandstone
60-150
Basalt
80-160
Quarzite
100-145
Three types of burnt bricks may be mentioned in todays Indian context: namely the country
brick, the table moulded brick and the wire cut brick. Country bricks are made using a simple
four sided mould.
Bricks are moulded by the soft mud process where soil has a high moisture content facilitating
easier pressing. The moulding is done on level ground and the wet bricks are left on the ground to
dry. After drying the bricks are stacked in clamp and burnt using firewood or paddy husk.
In the case of table moulded bricks, a five side mould is used to shape a relatively stiffer mud into
a brick. The use of lesser moisture at the time of moulding leads to an improved shape and
strength for the brick. The wet brick is released by turning the mould upside down on a level
platform. These bricks generally have a frog on one of the bedding faces. These bricks are then
dried in shade and then burnt in a continuous kiln known as the Bulls Trench Kiln. The table
moulded brick is generally much stronger than the country brick. Strengths ranging from 3.5 MPa
to 7.0 MPa is quite common for such bricks.
.The wire cut brick is produced by a more mechanized operation. The selected soil is pugged
adequately and then extrude into a continuous slab of clay. This slab is then sliced by a wire
frame into a number of bricks. After drying, the bricks are burnt in a Hoffmanns kiln. A good
wire cut brick retains a good shape and often has strengths in the range of 10.0 MPa to 20.00
MPa. It is also a very expensive brick and is not used a widely as the table moulded brick. It must
be pointed out that a wire cut brick masonry going up to 5 storeys without using RC frames. This
can be quite cost effective compared to framed construction.
DSCE
The concrete block offers flexibility in production which is not there in brick manufacture.
Page 10
Brick manufacture comes to a grinding halt during the monsoon while concrete block making can
be carried out throughout the year.
The investment needed by way of land and capital is much less for concrete block manufacture
compared to brick making.
The presence of excessive fine and use of low percentage of cement leads to lower strength. The
hollow concrete block can be deceptive in that it may look good but can have low strengths.
Hence, it must always be carefully evaluated for strength before using it in load bearing masonry.
Sl.No.
BLOCK SIZE
2.20
2.83
2.00
1.54
2.68
Use of hollow concrete block can be quite cost effective. The lower the bulk density of hollow
concrete block is a distinct advantage in construction of 3 to 4 storeys.
They can be useful as the dead weight is low. They will probably prove useful a t places close to
the factories manufacturing them.
These are burnt high clay blocks made by a process of extrusion. The wall thickness of the hollow
block is often as low as 1.5 to 2.0 cms. They come in various sizes.
It can be seen that these give a relatively high strength when tested with load parallel to the holes.
When the blocks are laid with the holes aligned horizontally the strength is substantially less.
DSCE
These blocks usually have bulk densities in the range of 950.0 kg/m3 to 1200 kg/m3
Page 11
It is interesting to note that these blocks have a rather favorable weight/strength ratio. They can
be quite useful in planning a building with several storeys since the dead weight can be kept low.
They also offer possibilities of improved thermal comfort when the wall thickness is 200 mm or
more and then external walls are painted white (or some light colour).
It is now well known that when soils are compacted using external energy, the density of the soil
reaches a maximum value at a moisture content known as the optimum moisture content (OMC).
The value of OMC and the maximum density depends on the energy input during compaction.
It is also easy to recognize that the compressive strength of the soil, in the dry state, depends on
the density.
Thus the process of mechanical compaction can lead to densification ad strengthening of the soil.
A variety of materials can be used for stabilization namely: cement, lime and bitumen.
Soil consisting of clay, slit and sand is the basic raw material.
It is preferable that the clay should be non-expansive, although expansive clays can also be
stabilized using a somewhat more complex procedure.
In general soils containing 10 to 15% clay and 65.0 to 70.0% sand are satisfactory for making
cement stabilized mud blocks.
Cement may be added to the tune of 6.0 to 8.0% by weight of the appropriate soil.
In case the soil has high clay content, sand or a sandy additive like quarry dust may be added to
correct the grading of the soil.
DSCE
Page 12
A combination of cement and lime can be used. For non-expansive soil and with clay content
around 15% a cement proportion of 5% and lime proportion 2% can be added for stabilization.
Lime has the advantage of combining with the clay in the soil and enhancing the long term
durability and strength.
The Process
The entire process of making a stabilized mud block may be summarized as under.
Mix sad or quarry dust to correct the clay-sand percentages in the soil.
Add cement or cement and lime in appropriate proportions and mix thoroughly in the dry
condition.
Sprinkle moisture onto the mixture and further mix thoroughly till the mixture is homogenous.
Test for optimum moisture by trying to make a ball of soil in the hand. If a ball can be made
without the soil sticking to the hand the moisture content is right.
Weight the correct amount o moist soil such that a fresh block density of 2.05 gm/cc can be
achieved. The weight depends on the volume of the finished block. In case the soil contains too
much sand and silt a density of 2.05 gm/cc may not feasible. Densities like 2.0 gm/cc or 1.95
gm/cc may be attempted.
The weighed soil is now poured into a soil compaction press like the Mardini.
The block is now pressed by operating the toggle lever, after closing the lid, the lid may then be
opened and the block ejected by again using the lever.
The ejected block is then stacked in a five or six block high stack for curing.
Sprinkling of moisture may be pursued up to 21 days to complete the block making process.
In general, it is desirable to have a block size, which is somewhat larger than the size of a brick to
achieve economy in the production of the material.
Usual sizes are 230x190z100 mm or 305x143x100mm. Blocks of thickness less than 100m can
be easily made, if necessary, by introducing thicker plates inside the mould.
DSCE
Page 13
A half block size of 230 x 108 x 100mm is also sometimes useful for corner joint, door and
window jambs, partition walls and so on.
Density and the proportion of cement added are two important parameters, which control the
strength and durability of stabilized mud blocks.
The strength is very sensitive to the dry density. As the dry density increases from 1.75 gm/cc to
1.9 g/cc the strength increases from 12.0 MPa to 2.0 Mpa.
Strength of Blocks
The SMB technology is well suited to produce a range of block strengths at the site.
As a rule a minimum wet compressive strength of 3.0 MPa is desirable for two storeyed house
constructions.
A cement percentage of 6 to 7% and a sand content of 65% and a clay content of 15% is usually
sufficient to achieve a minimum strength of 3.0 MPa.
Using higher percentages of cement, wet compressive strength in the range of 4.0 to 7.0 MPa can
be easily achieved.
A block with 7.0 MPa strength can be comfortably recommended for four storeyed load bearing
masonry.
DSCE
Page 14
It is a very simple technology involving using odd sized stones, which are shaped by a layer of
concrete surrounding the stone.
Steel moulds resting on level ground can be used to place the odd shaped stone in the centre of
the mould. Lean concrete is now poured in the space between the stone and the mould.
Block sizes of 300x200x150mm and 300x150x150mm are quite common, compressive strength
in the range of 5.0 to 10.0 MPa can be easily achieved.
This technology has been implemented in a large number of locations in India, whenever stone is
readily available.
Procurement from a location, which is hundreds of kilometers away, will often lead to expensive
wall construction.
For instance, procuring hollow clay blocks from Kerala for building in Bangalore will lead to
significant transport costs.
It is ideal if the building blocks can be obtained at distances less than 30 kms.
Bricks or Stabilized Mud Blocks which depend on soil as a resource will generally be feasible in
most locations since soils are more abundant than stones in nature.
DSCE
Page 15
DSCE
Page 16