Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
02
Date
2013-09-30
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
Contents
Contents
1 Introduction....................................................................................................................................1
1.1 Scope..............................................................................................................................................................................1
1.2 Intended Audience..........................................................................................................................................................1
1.3 Change History...............................................................................................................................................................1
2 Overview.........................................................................................................................................3
2.1 Background.....................................................................................................................................................................4
2.2 Pool Area........................................................................................................................................................................4
2.3 NRI.................................................................................................................................................................................6
2.4 NullNRI..........................................................................................................................................................................6
2.5 Non-broadcast LAI/RAI.................................................................................................................................................6
8 Feature Deployment....................................................................................................................19
8.1 Configuring Iu Flex......................................................................................................................................................19
8.1.1 Prerequisites...............................................................................................................................................................19
8.1.2 Procedure...................................................................................................................................................................19
8.1.3 Example.....................................................................................................................................................................25
8.2 Configuring Iu Flex Load Distribution Management...................................................................................................26
8.2.1 Prerequisites...............................................................................................................................................................26
8.2.2 Procedure...................................................................................................................................................................26
8.2.3 Example.....................................................................................................................................................................35
Issue 02 (2013-09-30)
ii
WCDMA RAN
Iu Flex Feature Parameter Description
Contents
9 Parameters.....................................................................................................................................37
10 Counters......................................................................................................................................90
11 Glossary.......................................................................................................................................92
12 Reference Documents...............................................................................................................93
Issue 02 (2013-09-30)
iii
WCDMA RAN
Iu Flex Feature Parameter Description
1 Introduction
Introduction
1.1 Scope
This document describes WRFD-021302 Iu Flex, including its technical principles, related
features, network impact, and engineering guidelines.
Feature change
Changes in features of a specific product version
Editorial change
Changes in wording or addition of information that was not described in the earlier version
02 (2013-09-30)
This issue includes the following changes.
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
1 Introduction
Change Type
Change Description
Parameter Change
Feature change
Added
RESERVED_SWITCH_3_
BIT32 to the RsvSwitch3
(BSC6900,BSC6910)
parameter in the SET
UALGORSVPARA
command.
Editorial change
None
None
01 (2013-04-28)
This issue does not include any changes.
Draft A (2013-01-30)
Compared with issue 01 (2012-07-20) of RAN14.0, Draft A (2013-01-30) of RAN15.0 includes
the following changes.
Change Type
Change Description
Parameter Change
Feature change
None
Editorial change
None
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
2 Overview
Overview
Iu Flex is an extended function of RAN. The 3GPP TS 23.236 defines Iu Flex as follows: "Intradomain Connection of Radio Access Network (RAN) Nodes to Multiple Core Network Nodes."
The Iu Flex (WRFD-021302 Iu Flex) brings in the concept of "pool area". A pool area contains
one or more MSC/SGSN service areas. In a pool area, the UE roams freely without changing
the serving CN node. The Iu Flex enables a RAN node to route information to different CN
nodes, implementing the load balance among MSCs or SGSNs.
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
2 Overview
2.1 Background
In the versions earlier than 3GPP R5, one RAN node is controlled by only one CN node. Such
a network structure, however, has some limitations. From the perspective of 3G traffic
distribution, the traffic volume of urban areas in the daytime constitutes a major proportion of
the total, but the traffic volume of urban areas at night decreases to a low level. The situation
may be reverse in the suburban area. Therefore, the load of CN nodes for urban and suburban
area is imbalanced.
Therefore, Iu Flex is introduced in 3GPP R5. With Iu Flex, one RAN node can be connected to
several CN nodes and these CN nodes can form a pool area. The UEs in the same pool area do
not need to change the serving CN node.
The introduction of Iu Flex avoids the imbalance of resource usage among different CN nodes
in different traffic peak hours and achieves the load balancing among several CN nodes in the
WCDMA network.
In a traditional network structure, a RAN node only needs to know whether the destination is
the CS domain or the PS domain before sending information. It does not need to discriminate
specific CN nodes because a RAN node is connected to only one CN node.
With Iu Flex, however, one RNC can connect to several MSCs/SGSNs physically, where CS
nodes and PS nodes form different pool areas. Therefore, a RAN node can send information to
different CN nodes in the CS or PS domain and achieve load balancing among several CN nodes
in the pool area.
The pool area is described as follows:
l
A pool area is a collection of one or more MSC or SGSN serving areas. One or more CN
nodes can provide services in parallel and these CN nodes share the traffic in the pool area.
Pool areas may overlap. RAN nodes belong to all the overlapping pool areas.
If a UE roams in a certain pool area, it does not need to change the serving CN node.
The Iu Flex feature enhances network reliability, achieves load balancing, and reduces UE
roaming signaling.
WCDMA RAN
Iu Flex Feature Parameter Description
2 Overview
In a pool area, the UE roams freely without changing the serving CN node. The RAN node
service area can belong to the same pool area or several pool areas.
Figure 2-1 shows an example of the pool area configurations.
Figure 2-1 Pool area configuration example
CS pool area 1: includes RAN node areas 1, 2, 5, 6, and MSC servers 1, 2, and 3, which
provide service for the RAN node areas.
CS pool area 2: includes RAN node areas 2, 3, 6, 7, and MSC servers 4, 5, and 6, which
provide service for the RAN node areas.
PS pool area 1: includes RAN node areas 1 and 5, and SGSNs 1 and 2, which provide
service for the RAN node areas.
PS pool area 2: includes RAN node areas 2, 3, 6, 7, and SGSN 3, 4, and 5, which provide
service for the RAN node areas.
NOTE
As shown in Figure 2-1, the pool areas without the Iu Flex, such as RAN node areas 4 and 8, may coexist
with the pool areas with the Iu Flex.
The pool areas of the CS and PS domains can be configured as identical pool areas, such as CS
pool area 2 and PS pool area 2, or different pool areas, such as CS pool area 1 and PS pool area
1.
Each pool area has its unique configuration of the CN node capability or number.
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
2 Overview
2.3 NRI
The Network Resource Identifier (NRI) identifies the CN node that serves a pool area. The NRI
has a flexible length from 0 bit to 10 bits. 0 bit means no Iu flex. The NRI lengths are the same
for all the CN nodes in one pool area.
In areas where pool areas overlap, the NRI identifies the CN node that serves these overlapping
pool areas. For overlapping pool areas, the NRI lengths must be configured the same for all the
nodes serving specific pool areas.
The CN nodes in the CS domain and those in the PS domain are addressed separately, so the
NRIs of the CS and PS domains are independent of each other.
The NRI is a part of the Temporary Mobile Station Identity (TMSI) for the CS domain, or of
the Packet TMSI (P-TMSI) for the PS domain. The TMSI or P-TMSI is assigned to the UE by
the serving CN node. The TMSI or P-TMSI allocation mechanism of the CN node generates
TMSIs or P-TMSIs with NRIs determined by certain bits.
The association between the NRIs and the CN nodes in the CN pool area is configured on the
RAN nodes.
In the WCDMA system, the UE provides an intra domain NAS node selector (IDNNS) in the
access stratum (AS) part of the Initial Direct Transfer message to the RAN node. The IDNNS
contains a routing parameter with a fixed length of 10 bits. This routing parameter contains the
NRI information. In addition, the IDNNS contains the identity that indicates the source of the
routing parameters. The identity can be TMSI/P-TMSI, international mobile subscriber identity
(IMSI), international mobile equipment identity (IMEI), and so on. The RAN node masks the
significant bits out of the routing parameter part of the IDNNS to determine the NRI that is used
to identify the relevant CN node. The most significant bit of the NRI corresponds to the most
significant bit of the routing parameter in the IDNNS. A routing parameter containing the identity
of IMSI is in range of 0 to 999 (calculated by (IMSI div 10) mod 1000) and is called IMSIROUTE
in this document. The association between IMSIROUTE and the CN nodes in the CN pool area
is configured on the RNC.
2.4 NullNRI
NullNRI is a special value of the NRI, which indicates that the CN node identified by the NRI
is to be offloaded. On receiving a message carrying NullNRI, the RNC starts the IDNNS function
to select an appropriate CN node. NullNRI can be unique in a Public Land Mobile Network
(PLMN) or set separately in the CS domain and PS domain.
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
NAS Node Selection Function (NNSF) is used to select an appropriate CN Node for a UE.
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
3.1 Overview
The NNSF performs the selection of a CN node and the processing of the IMSI Paging Message
in both the CS and PS domain.
In the RAN node, the NNSF selects a specific CN node (MSC server or SGSN) and routes the
initial NAS signaling message to the selected CN node.
If a CN node address configured for the NRI can be derived from the initial NAS signaling
message, the NNSF routes the message to the CN node. If no CN node address is configured for
the derived NRI or no NRI can be derived (for example, the UE indicates an identity that contains
no NRI), or the configured CN node cannot be reached, the NNSF selects an available CN node
based on load balancing and routes the message to the selected CN node.
The procedure for NNSF is as follows:
1.
2.
UE indicates the route information and sends it to the RNC in the Initial Direct Transfer
message.
3.
RNC selects the CN Node based on the routing information in the Initial Direct Transfer
message.
The first part indicates the ID type (TMSI/P-TMSI, IMSI, IMEI) used for calculating the
routing parameter.
The second part indicates the routing parameter with a fixed length of 10 bits.
2.
If the TMSI/P-TMSI information is unavailable, but the MS has the USIM/SIM card, the
coding is performed based on the IMSI. The routing parameter is derived from IMSI and
calculated as (IMSI div 10) mod 1000, where "div" means divided by and "mod" means
modulus.
3.
If the MS is not inserted with the USIM/SIM card, the coding is performed based on the
IMEI. The routing parameter is derived from IMEI and calculated as (IMEI div 10) mod
1000.
Issue 02 (2013-09-30)
WCDMA RAN
Iu Flex Feature Parameter Description
Calling and called parties follow the same way of selecting the CN node based on TMSI/PTMSI.
If the Initial Direct Transfer message indicates that this message is initiated by a mobile
originated call,
If the IMSI route of a UE is within the configured IMSI range of a CN node, the RNC
routes the UE to the CN node.
The mapping is configured on RNC by running the ADD UIMSIIDNNSCNIDMAP
command.
If the IMSI route of a UE is not configured, the RNC selects a CN node based on the
load balancing.
If the Initial Direct Transfer message indicates that this message is initiated by a mobile
terminated call (paging response), the RNC routes the UE based on the mapping between
IMSI and global CN ID received from CN. If fails, the terminated call is processed as an
originated call.
WCDMA RAN
Iu Flex Feature Parameter Description
The NNSF in the RNC temporarily stores the map between the IMSI and the Global-CNID upon reception of the paging message. When the NNSF receives the Initial Direct
Transfer message (a paging response with an IMSI), it directly forwards the paging response
to the CN node identified by this Global-CN-ID.
If a CS paging message with mobile identity type IMSI is received over the Gs interface from
the MSC, the SGSN has to contain the MSC/VLR-ID in the paging message or paging-request
message to the RNC.
Issue 02 (2013-09-30)
10
WCDMA RAN
Iu Flex Feature Parameter Description
1.
The MS accesses the network through the RAN1, and provides the IDNNS to the RAN1.
2.
The RAN1 obtains the corresponding SGSN based on the IDNNS, and then connects the
MS to the SGSN1.
3.
The SGSN1 sends its NRI to the MS when the MS access is completed.
4.
Issue 02 (2013-09-30)
11
WCDMA RAN
Iu Flex Feature Parameter Description
5.
When the MS requests to access the network though the RAN2, the MS provides the IDNNS
to the RAN2, containing the SGSN1 NRI.
6.
The RAN2 finds the SGSN1 that serves the MS originally, and then connects the MS to
the SGSN1 that serves the MS at the first time of network access.
When a UE is moving within a Pool area, the UE can be continuously served by a certain CN
node. Therefore, the location update process between the SGSNs is avoided, and the network
load is reduced.
Issue 02 (2013-09-30)
12
WCDMA RAN
Iu Flex Feature Parameter Description
5 Load Balancing
Load Balancing
Load Balancing (WRFD-021306 Iu Flex Load Distribution Management) describes how the
NNSF balances the load between the available CN nodes.
The RNC selects a CN node from the available CN nodes based on the load balancing principle.
Load balancing occurs in one of the following situations:
l
There is no CN node configured for the NRI or IMSIROUTE indicated by the UE.
Based on the load balancing principle, the RNC records the capability of each CN node which
is configured to the NORMAL state and is not in overloaded, and then selects a CN node based
on randomization function for the UE.
Assume that the RNC is connected to three MSCs in NORMAL state (identified as MSC A, B,
and C) and their available capabilities are 10, 20, and 10, respectively. Among the UEs accessing
in load balancing condition, 25% of UEs are routed to MSC A, 50% of UEs are routed to MSC
B, and 25% of UEs are routed to MSC C, according to the rules of load balancing. Other UEs
are routed to the specific CN nodes identified by the NRI.
NOTE
If a CN node whose available capacity is 0 is identified by a valid NRI and the route parameters of a UE
include the NRI, the UE will still be routed to the CN node.
Static capability
The static capability of the CN node is specified by the AvailCap(BSC6900,BSC6910) of
the ADD UCNNODE command in the RNC.
Dynamic capability
The dynamic capability reflects the real-time state of the CN node capability.
If the parameters CsInfoUpdFlag(BSC6900,BSC6910) or PsInfoUpdFlag
(BSC6900,BSC6910) in the RNC is set to ON, the CN informs the RNC of the dynamic
capability and state through the private IEs of the INFORMATION TRANSFER INDICATION
Issue 02 (2013-09-30)
13
WCDMA RAN
Iu Flex Feature Parameter Description
5 Load Balancing
message. Therefore, the data between the CN and the RNC is synchronized to realize load
balancing.
If the RNC does not receive the message about updating the dynamic capability before the CS
Information Update Protection Timer or PS Information Update Protection Timer expires, the
static capability is preferred.
NOTE
Issue 02 (2013-09-30)
14
WCDMA RAN
Iu Flex Feature Parameter Description
6 Flow Control
Flow Control
The RNC considers a CN code to be congested when either of the following occurs:
l
In non-Iu Flex networking, if a CN node is congested, the RNC reduces the load on the CN node.
For details, see Flow Control Feature Parameter Description.
In Iu Flex networking, when receiving an Initial Direct Transfer message from a UE, the RNC
forwards the message to the correct CN node based on the routing information carried in the
message. If the CN node is congested, the RNC determines whether to send the message to the
CN code based on the severity of the congestion and randomization function. If the RNC
determines not to send the message to the CN code, the RNC processes the message based on
the setting of RESERVED_SWITCH_3_BIT32 in the RsvSwitch3(BSC6900,BSC6910)
parameter in the RNC command SET UALGORSVPARA.
l
The RNC selects the CN node for the UE based on the proportion of the available capability of each CN
node in the NORMAL state.
Issue 02 (2013-09-30)
15
WCDMA RAN
Iu Flex Feature Parameter Description
7 Load Re-Distribution
Load Re-Distribution
There are situations where a network operator needs to remove load from one CN node (for
example, to perform scheduled maintenance, upgrade or load re-distribution to avoid overload),
with minimal impact on end users, or additional load on other entities, or both.
Load Re-Distribution helps to re-distribute UEs to other CN nodes. There are two ways to
implement load re-distribution:
l
Issue 02 (2013-09-30)
16
WCDMA RAN
Iu Flex Feature Parameter Description
7 Load Re-Distribution
In the first phase (a couple of Periodic LU or RAU periods long), the UEs doing Location
Update (LU), Routing Area Update (RAU), or Attach are moved to the other CN nodes in
the pool.
When the CN node receives the LU, RAU, or Attach request, it returns a new TMSI or PTMSI with a NullNRI, and a Non-broadcast LAI/RAI in the accept message.
l In the CS domain, the non-broadcast LAI will cause the UE to immediately send a new
LU request, which the RNC node will perform load balancing to route the UE to a new
MSC server due to the NullNRI.
l In the PS domain, the non-broadcast RAI will cause the UE to send a new RAU request.
The periodic routing area update timer is set to a sufficiently low value in the accept
message to reduce the time to trigger the RAU. Shortly after that, the UE sends a new
RAU request, which the RNC node will perform load balancing to route the UE to a
new SGSN due to the NullNRI.
2.
In the second phase (PS domain specific), the SGSN requests all UEs trying to set up PDP
Contexts to detach and reattach. When they reattach, the SGSN moves them as described
in the first phase.
3.
The third phase includes scanning the remaining UEs and initiating the movement of them
to other CN nodes.
In the PS domain, the UEs are requested to detach and reattach, which will cause them to
be moved.
In the CS domain, a new TMSI is allocated to the UEs performing the TMSI re-allocation
procedure (with NullNRI and non-broadcast LAI) so that an LU is triggered, which will
cause them to be moved.
The RNC selects CN node based on the CN state for load re-distribution. The CN state is
negotiated between CN and RAN. The state of CN should be specified in the RNC by the
parameterCNLoadStatus(BSC6900,BSC6910). The state for a CN node can be NORMAL,
OFFLOAD, INHIBITED or BLOCKED.
The principle for selecting a CN node for load re-distribution is as follows:
l
The UEs being moved from one CN node are prevented from registering in the same CN
node again or in a CN node that is overloaded.
The RNC ensures that the movements do not overload the network and the RNC can handle
the situations where several CN nodes are overloaded simultaneously.
Issue 02 (2013-09-30)
17
WCDMA RAN
Iu Flex Feature Parameter Description
7 Load Re-Distribution
For multi-operator core network (MOCN) network sharing, re-distribution is always done within
the same CN operator. This is ensured by each CN operator using its own unique NullNRI. The
RNC is pre-configured with the NullNRIs for different CN operators, and it uses the NullNRI
to select a CN node within the same CN operator.
When the CN is in BLOCKED state and other CNs are in NORMAL state, the UEs that
are routed to this CN node cannot access the CN and will be routed to other CNs. However,
the UE can still access the CN node if the UE is responding to the paging message from
this CN node.
When the CN is in BLOCKED state and other CNs are in INHIBITED state or in
OFFLOAD state or are disconnected or are overloaded, the UEs can still access the CN
node.
Issue 02 (2013-09-30)
18
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
Feature Deployment
8.1.1 Prerequisites
l
Dependencies on Hardware
This feature does not depend on the hardware.
License
The license " IU FLEX" on the RNC side has been activated. For details about the license
items and how to activate the license, see License Management Feature Parameter
Description.
Others
The MSC and the serving GPRS support node (SGSN) support this feature.
8.1.2 Procedure
Activation (Using MML Commands)
1.
Run the RNC MML command SET UOPERATORCFGPAR. In this step, set Feature
Supporting Mode of CS Domain to SUPP_IUFLEX, set Feature Supporting Mode of PS
Domain to SUPP_IUFLEX, and set Length of CS NRI in bits and Length of PS NRI in
bits to appropriate values.
2.
Configure the Iu interface transmission between RNC and multiple core networks (CNs)
by referring to "Configuring the Interfaces" in RNC UMTS Initial Configuration Guide.
3.
Run the RNC MML command ADD UCNNODE to add multiple CN nodes for an operator
according to the network plan.
Issue 02 (2013-09-30)
19
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
NOTE
The CNId of the same PLMN cannot be the same,even the different CN domain. The setting of
CNId must be consistent between the RNC and CN. If CNId on the CN is set to 5, CNId on the
RNC must also be set to 5.
4.
Run the RNC MML command ADD UNRIGLBCNIDMAP. In this step, set Cn Operator
Index, CN node ID, and Network resource identity to configure the mapping
relationships between NRI and CN nodes.
5.
After configuring the mapping relationships, the RNC routes the UE whose IMSI is within the
IMSI range to the specified CN. To ensure load balance among CN nodes, the IMSI range
mapped to each CN node must match the capacity of the CN node.
When configuring the feature on the CME, you must configure a single configuration first, and then perform
batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
Issue 02 (2013-09-30)
SN
MO
NE
Parameter Name
Parameter ID
Configurable
in CME Batch
Modification
Center
UOPERA
TORCFG
PARA
RNC
Feature Supporting
Mode of CS Domain
CsNriCfgMode
(BSC6900,
BSC6910)
No
20
WCDMA RAN
Iu Flex Feature Parameter Description
SN
MO
8 Feature Deployment
NE
Parameter Name
Parameter ID
Feature Supporting
Mode of PS Domain
PsNriCfgMode
(BSC6900,
BSC6910)
Issue 02 (2013-09-30)
UCNNOD
E
RNC
Length of CS NRI in
bits
CSNRILength
(BSC6900,
BSC6910)
Length of PS NRI in
bits
PSNRILength
(BSC6900,
BSC6910)
Cn Operator Index
CnOpIndex
(BSC6900,
BSC6910)
CN node ID
CNId
(BSC6900,
BSC6910)
CN domain ID
CNDomainId
(BSC6900,
BSC6910)
DSP index
Dpx
(BSC6900,
BSC6910)
CN protocol version
CNProtclVer
(BSC6900,
BSC6910)
CNLoadStatus
CNLoadStatus
(BSC6900,
BSC6910)
AvailCap
AvailCap
(BSC6900,
BSC6910)
Iu transfers bearer
type
TnlBearerType
(BSC6900,
BSC6910)
Switch3GPP25415
CR0125
Switch3GPP25
415CR0125
(BSC6900,
BSC6910)
Configurable
in CME Batch
Modification
Center
No
21
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
SN
MO
NE
Parameter Name
Parameter ID
Configurable
in CME Batch
Modification
Center
UNRIGL
BCNIDM
AP
RNC
Cn Operator Index
CnOpIndex
(BSC6900,
BSC6910)
No
CN node ID
CNId
(BSC6900,
BSC6910)
Network resource
identity
NRI
(BSC6900,
BSC6910)
Minimum of IMSI
route parameter in
IDNNS
ImsiRtMin
(BSC6900,
BSC6910)
Maximum of IMSI
route parameter in
IDNNS
ImsiRtMax
(BSC6900,
BSC6910)
Cn Operator Index
CnOpIndex
(BSC6900,
BSC6910)
CN node ID
CNId
(BSC6900,
BSC6910)
UIMSIID
NNSCNI
DMAP
RNC
No
Verification Procedure
1.
2.
According to the mapping relationships between IMSI ranges and CN nodes and the load
balance algorithm, the RNC selects a CN node for the UE, and the UE registers successfully.
3.
Then, if the UE initiates a service, the RNC routes the UE to the corresponding CN node
according to the mapping relationships between NRI and CN nodes.
Run the RNC MML command RMV UNRIGLBCNIDMAP to remove NRI and all of CN
Node Mapping Information.
2.
Run the RNC MML command RMV UCNNODE to remove CN Node (Keep one CN
Node).
3.
(Optional) Run the RNC MML command RMV UIMSIIDNNSCNIDMAP to remove the
mapping relationships between IMSIROUTE and CN nodes.
Issue 02 (2013-09-30)
22
WCDMA RAN
Iu Flex Feature Parameter Description
4.
8 Feature Deployment
Run the RNC MML command SET UOPERATORCFGPARA to deactivate this feature.
In this step, set Feature Supporting Mode of CS Domain to SUPP_NONE, set Feature
Supporting Mode of PS Domain to SUPP_NONE.
When configuring the feature on the CME, you must configure a single configuration first, and then perform
batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
MO
SN
MO
NE
Paramete
r Name
Paramete
r ID
Configur
able in
CME
Batch
Modifica
tion
Center
UNRIGLBCNIDMAP
NOTE
Delete the MO
configuration.
Issue 02 (2013-09-30)
RN
C
Cn Operator Index
CnOpI
ndex
(
BSC69
00,
BSC69
10)
No
23
WCDMA RAN
Iu Flex Feature Parameter Description
SN
MO
8 Feature Deployment
SN
MO
NE
Paramete
r Name
Paramete
r ID
Configur
able in
CME
Batch
Modifica
tion
Center
UCNNODE
NOTE
Delete the MO
configuration.
UIMSIIDNNSCNIDMAP
RN
C
RN
C
CN node ID
CNId
(
BSC69
00,
BSC69
10)
Network resource
identity
NRI
(
BSC69
00,
BSC69
10)
Cn Operator Index
CnOpI
ndex
(
BSC69
00,
BSC69
10)
CN node ID
CNId
(
BSC69
00,
BSC69
10)
ImsiRt
Min
(
BSC69
00,
BSC69
10)
NOTE
Delete the MO
configuration.
Issue 02 (2013-09-30)
No
No
24
WCDMA RAN
Iu Flex Feature Parameter Description
SN
MO
8 Feature Deployment
SN
MO
NE
Paramete
r Name
Paramete
r ID
Configur
able in
CME
Batch
Modifica
tion
Center
UOPERATORCFGP
ARA
RN
C
ImsiRt
Max
(
BSC69
00,
BSC69
10)
Cn Operator Index
CnOpI
ndex
(
BSC69
00,
BSC69
10)
CN node ID
CNId
Feature Supporting
Mode of CS Domain
CsNriC
fgMode
(
BSC69
00,
BSC69
10)
Feature Supporting
Mode of PS Domain
Set this parameter to
SUPP_NONE
No
PsNriC
fgMode
(
BSC69
00,
BSC69
10)
8.1.3 Example
//Activating Iu Flex
//Configuring the RNC supporting Iu Flex with Length of CS NRI in bits and Length
of PS NRI in bits set to appropriate values
Issue 02 (2013-09-30)
25
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
8.2.1 Prerequisites
l
Dependencies on Hardware
This feature does not have any special requirements for hardware.
License
The license "Enhanced Iu Flex" on the RNC side has been activated. For details about the
license items and how to activate the license, see License Management Feature Parameter
Description.
Other Prerequisites
The CN supports dynamic capacity management and load redistribution.
8.2.2 Procedure
Activation (Using MML Commands)
l
1.
Run the RNC MML command MOD UCNNODE. In this step, set Capability of CN
Node to an appropriate value. The RNC performs load balancing between CN nodes based
on the configured CN capacities.
Issue 02 (2013-09-30)
26
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
1.
Load balancing in dynamic capacity mode takes effect only when the RNC is connected to
Huawei CN and the preceding switches related to Iu Flex are turned on.
1.
Run the RNC MML command MOD UCNNODE. In this step, set Status of CN Node to
OFFLOAD.
2.
Run the RNC MML command SET UOPERATORCFGPARA. In this step, set NullNRI
VALUE to an appropriate value based on the network plan.
1.
Run the RNC MML command MOD UCNNODE. In this step, set Status of CN Node to
NORMAL and select the IUFLEX_NOT_SEL_BLOCK_SWITCH(IUFLEX NOT
SEL BLOCK SWITCH) check box under the parameter PROCESS SWITCH.
When configuring the feature on the CME, you must configure a single configuration first, and then
perform batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
1.
2.
(Optional) Modify objects in batches on the CME. (CME batch modification center)
on the CME to start the batch modification
To modify objects in batches, click
wizard. For instructions on how to perform a batch modification through the CME
batch modification center, press F1 on the wizard interface to obtain online help.
Issue 02 (2013-09-30)
27
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
SN
MO
NE
Paramete
r Name
Paramete
r ID
Configur
able in
CME
Batch
Modificat
ion
Center
UCNNOD
E
RNC
Capability
of CN
Node
AvailCap
(BSC6900,
BSC6910)
No
When configuring the feature on the CME, you must configure a single configuration first, and then
perform batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
1.
2.
(Optional) Modify objects in batches on the CME. (CME batch modification center)
on the CME to start the batch modification
To modify objects in batches, click
wizard. For instructions on how to perform a batch modification through the CME
batch modification center, press F1 on the wizard interface to obtain online help.
Table 8-4 Parameters to be set on the CME
SN
MO
NE
Paramete
r Name
Paramete
r ID
Configur
able in
CME
Batch
Modificat
ion
Center
UOPERA
TORCFG
PARA
RNC
Feature
Supporting
Mode of
CS Domain
CsNriCfg
Mode
(BSC6900,
BSC6910)
No
Set this
parameter
to
SUPP_IUF
LEX
Issue 02 (2013-09-30)
28
WCDMA RAN
Iu Flex Feature Parameter Description
SN
8 Feature Deployment
MO
NE
Paramete
r Name
Paramete
r ID
Feature
Supporting
Mode of PS
Domain
PsNriCfg
Mode
(BSC6900,
BSC6910)
Configur
able in
CME
Batch
Modificat
ion
Center
Set this
parameter
to
SUPP_IUF
LEX
CS
Informatio
n Update
Switch
CsInfoUpd
Flag
(BSC6900,
BSC6910)
Set this
parameter
to ON
PS
Informatio
n Update
Switch
PsInfoUpd
Tmr
(BSC6900,
BSC6910)
Set this
parameter
to ON
l
When configuring the feature on the CME, you must configure a single configuration first, and then
perform batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
1.
2.
(Optional) Modify objects in batches on the CME. (CME batch modification center)
on the CME to start the batch modification
To modify objects in batches, click
wizard. For instructions on how to perform a batch modification through the CME
batch modification center, press F1 on the wizard interface to obtain online help.
Issue 02 (2013-09-30)
29
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
MO
NE
Paramet
er Name
Parameter
ID
Configur
able in
CME
Batch
Modifica
tion
Center
UCNNO
DE
RNC
Status of
CN Node
CNLoadSta
tus
(BSC6900,
BSC6910)
No
NullNRI
(BSC6900,
BSC6910)
No
Set this
paramete
r
OFFLOA
D
2
UOPER
ATORC
FGPAR
A
RNC
NullNRI
VALUE
When configuring the feature on the CME, you must configure a single configuration first, and then
perform batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
1.
2.
(Optional) Modify objects in batches on the CME. (CME batch modification center)
on the CME to start the batch modification
To modify objects in batches, click
wizard. For instructions on how to perform a batch modification through the CME
batch modification center, press F1 on the wizard interface to obtain online help.
Issue 02 (2013-09-30)
30
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
MO
NE
Parameter Name
Parameter
ID
Config
urable
in
CME
Batch
Modif
ication
Center
UCNN
ODE
RN
C
Status of CN Node
CNLoadSta
tus
(BSC6900,
BSC6910)
No
PROCESSS WITCH
Set this parameter to
IUFLEX_NOT_SEL_BLOCK_S
WITCH-1
PROCESS
SWITCH
(BSC6900,
BSC6910)
Verification Procedure
l
1.
Run the RNC MML command DSP UCNNODE to query the capacity ratio of CN nodes.
2.
Check the following performance counters on the M2000 to verify that the RNC performs
load balancing based on the preconfigured CN capacity:
1.
Run the RNC MML command DSP UCNNODE to query the capacity ratio of CN nodes.
2.
On the RNC LMT, choose Trace > UMTS Services to initiate Uu and Iu interface message
tracing.
3.
Check the traced messages. If the CN sends the RNC an INFORMATION TRANSFER
INDICATION message, the dynamic CN capacity ratio is updated and used. If the CN
does not send any INFORMATION TRANSFER INDICATION message to the RNC,
the static CN capacity ratio is used.
4.
Check the following performance counters on the M2000 to verify that the RNC performs
load balancing based on the dynamic CN capacity ratio:
Issue 02 (2013-09-30)
31
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
1.
On the RNC LMT, choose Trace > UMTS Services to initiate Uu and Iu interface message
tracing.
2.
3.
Set SGSN1 to the OFFLOAD state and SGSN2 to the NORMAL state on the RNC.
4.
5.
Power on the UE and the UE makes an attach request. Check the traced Iu interface
messages. The expected result is as follows:
l The RNC routes the RRC_INIT_DIRECT_TRANSFER message to SGSN1 based
on NULL NRI. The attach reception message from SGSN1 contains NULL NRI and
non-broadcasting location areas.
l After receiving the non-broadcasting location areas, the UE sends a new routing area
update (RAU) request and contains NULL NRI in the
RRC_INIT_DIRECT_TRANSFER message. The RNC routes the
RRC_INIT_DIRECT_TRANSFER message to SGSN2, of which the state is not
OFFLOAD, based on NULL NRI.
1.
On the RNC LMT, choose Trace > UMTS Services to initiate Uu and Iu interface message
tracing.
2.
3.
Set SGSN1 to the BLOCK state and SGSN2 to the NORMAL state on the RNC.
4.
1.
Run the RNC MML command SET UOPERATORCFGPARA. In this step, set CS
Information Update Switch to OFF and PS Information Update Switch to OFF.
Issue 02 (2013-09-30)
32
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
1.
Run the RNC MML command MOD UCNNODE. In this step, set Status of CN Node to
NORMAL.
1.
Run the RNC MML command MOD UCNNODE. In this step, set Status of CN Node to
NORMAL and deselect the IUFLEX_NOT_SEL_BLOCK_SWITCH(IUFLEX NOT
SEL BLOCK SWITCH) check box under the parameter PROCESS SWITCH.
When configuring the feature on the CME, you must configure a single configuration first, and then
perform batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
1.
2.
(Optional) Modify objects in batches on the CME. (CME batch modification center)
on the CME to start the batch modification
To modify objects in batches, click
wizard. For instructions on how to perform a batch modification through the CME
batch modification center, press F1 on the wizard interface to obtain online help.
Table 8-7 Parameters to be set on the CME
SN
MO
NE
Parameter Name
Paramet
er ID
Config
urable
in
CME
Batch
Modifi
cation
Center
UOPERATOR
CFGPARA
RN
C
CS Information Update
Switch
CsInfoU
pdFlag
(
BSC6900
,
BSC6910
)
No
Issue 02 (2013-09-30)
33
WCDMA RAN
Iu Flex Feature Parameter Description
SN
8 Feature Deployment
MO
NE
Parameter Name
Paramet
er ID
PS Information Update
Protection Timer
PsInfoU
pdTmr
(
BSC6900
,
BSC6910
)
Config
urable
in
CME
Batch
Modifi
cation
Center
When configuring the feature on the CME, you must configure a single configuration first, and then
perform batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
1.
2.
(Optional) Modify objects in batches on the CME. (CME batch modification center)
on the CME to start the batch modification
To modify objects in batches, click
wizard. For instructions on how to perform a batch modification through the CME
batch modification center, press F1 on the wizard interface to obtain online help.
Table 8-8 Parameters to be set on the CME
SN
MO
NE
Paramete
r Name
Paramete
r ID
Configur
able in
CME
Batch
Modificat
ion
Center
UCNNOD
E
RNC
Status of
CN Node
CNLoadSt
atus
(BSC6900,
BSC6910)
No
Set this
parameter
to
NORMAL
Issue 02 (2013-09-30)
34
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
When configuring the feature on the CME, you must configure a single configuration first, and then
perform batch modifications if required.
You must perform a single configuration for a parameter before batch modifications of the parameter. You
are advised to perform batch modifications before logging out of the parameter setting interface.
1.
2.
(Optional) Modify objects in batches on the CME. (CME batch modification center)
To modify objects in batches, click
on the CME to start the batch modification
wizard. For instructions on how to perform a batch modification through the CME
batch modification center, press F1 on the wizard interface to obtain online help.
Table 8-9 Parameters to be set on the CME
SN
MO
NE
Paramete
r Name
Paramete
r ID
Configur
able in
CME
Batch
Modificat
ion
Center
UCNNOD
E
RNC
Status of
CN Node
CNLoadSt
atus
(BSC6900,
BSC6910)
No
Set this
parameter
to
NORMAL
PROCESS
S WITCH
Set this
parameter
to
IUFLEX_
NOT_SEL
_BLOCK_
SWITCH0
PROCESS
SWITCH
(BSC6900,
BSC6910)
8.2.3 Example
//Activating Iu Flex Load Distribution Management
//Configuring Load balancing in static capacity mode
Issue 02 (2013-09-30)
35
WCDMA RAN
Iu Flex Feature Parameter Description
8 Feature Deployment
Issue 02 (2013-09-30)
36
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameters
NE
MML
Command
Feature ID
Feature Name
Description
RsvSwitch3
BSC6900
SET
UALGORSVP
ARA
None
None
Meaning:RRM
algorithm
reserved U32
Switch Para 3.
The 32-bit
parameter is
reserved for
further change
request use.
Disuse
statement: This
parameter is
used
temporarily in
patch versions
and will be
replaced with a
new parameter
in later versions.
The new
parameter ID
reflects the
parameter
function.
Therefore, this
parameter is not
recommended
for the
configuration
interface.
Issue 02 (2013-09-30)
37
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
GUI Value
Range:RESER
VED_SWITCH
_3_BIT1,
RESERVED_S
WITCH_3_BIT
2,
RESERVED_S
WITCH_3_BIT
3,
RESERVED_S
WITCH_3_BIT
4,
RESERVED_S
WITCH_3_BIT
5,
RESERVED_S
WITCH_3_BIT
6,
RESERVED_S
WITCH_3_BIT
7,
RESERVED_S
WITCH_3_BIT
8,
RESERVED_S
WITCH_3_BIT
9,
RESERVED_S
WITCH_3_BIT
10,
RESERVED_S
WITCH_3_BIT
11,
RESERVED_S
WITCH_3_BIT
12,
RESERVED_S
WITCH_3_BIT
13,
RESERVED_S
WITCH_3_BIT
14,
RESERVED_S
WITCH_3_BIT
15,
RESERVED_S
WITCH_3_BIT
Issue 02 (2013-09-30)
38
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
16,
RESERVED_S
WITCH_3_BIT
17,
RESERVED_S
WITCH_3_BIT
18,
RESERVED_S
WITCH_3_BIT
19,
RESERVED_S
WITCH_3_BIT
20,
RESERVED_S
WITCH_3_BIT
21,
RESERVED_S
WITCH_3_BIT
22,
RESERVED_S
WITCH_3_BIT
23,
RESERVED_S
WITCH_3_BIT
24,
RESERVED_S
WITCH_3_BIT
25,
RESERVED_S
WITCH_3_BIT
26,
RESERVED_S
WITCH_3_BIT
27,
RESERVED_S
WITCH_3_BIT
28,
RESERVED_S
WITCH_3_BIT
29,
RESERVED_S
WITCH_3_BIT
30,
RESERVED_S
WITCH_3_BIT
31,
RESERVED_S
Issue 02 (2013-09-30)
39
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
WITCH_3_BIT
32
Unit:None
Actual Value
Range:RESER
VED_SWITCH
_3_BIT1,
RESERVED_S
WITCH_3_BIT
2,
RESERVED_S
WITCH_3_BIT
3,
RESERVED_S
WITCH_3_BIT
4,
RESERVED_S
WITCH_3_BIT
5,
RESERVED_S
WITCH_3_BIT
6,
RESERVED_S
WITCH_3_BIT
7,
RESERVED_S
WITCH_3_BIT
8,
RESERVED_S
WITCH_3_BIT
9,
RESERVED_S
WITCH_3_BIT
10,
RESERVED_S
WITCH_3_BIT
11,
RESERVED_S
WITCH_3_BIT
12,
RESERVED_S
WITCH_3_BIT
13,
RESERVED_S
WITCH_3_BIT
14,
RESERVED_S
Issue 02 (2013-09-30)
40
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
WITCH_3_BIT
15,
RESERVED_S
WITCH_3_BIT
16,
RESERVED_S
WITCH_3_BIT
17,
RESERVED_S
WITCH_3_BIT
18,
RESERVED_S
WITCH_3_BIT
19,
RESERVED_S
WITCH_3_BIT
20,
RESERVED_S
WITCH_3_BIT
21,
RESERVED_S
WITCH_3_BIT
22,
RESERVED_S
WITCH_3_BIT
23,
RESERVED_S
WITCH_3_BIT
24,
RESERVED_S
WITCH_3_BIT
25,
RESERVED_S
WITCH_3_BIT
26,
RESERVED_S
WITCH_3_BIT
27,
RESERVED_S
WITCH_3_BIT
28,
RESERVED_S
WITCH_3_BIT
29,
RESERVED_S
WITCH_3_BIT
30,
RESERVED_S
Issue 02 (2013-09-30)
41
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
WITCH_3_BIT
31,
RESERVED_S
WITCH_3_BIT
32
Default
Value:RESERV
ED_SWITCH_
3_BIT1-0&RES
ERVED_SWIT
CH_3_BIT2-0&
RESERVED_S
WITCH_3_BIT
3-0&RESERVE
D_SWITCH_3_
BIT4-0&RESE
RVED_SWITC
H_3_BIT5-0&R
ESERVED_SW
ITCH_3_BIT60&RESERVED
_SWITCH_3_B
IT7-0&RESER
VED_SWITCH
_3_BIT8-0&RE
SERVED_SWI
TCH_3_BIT9-0
&RESERVED_
SWITCH_3_BI
T10-0&RESER
VED_SWITCH
_3_BIT11-0&R
ESERVED_SW
ITCH_3_BIT12
-0&RESERVE
D_SWITCH_3_
BIT13-0&RES
ERVED_SWIT
CH_3_BIT14-0
&RESERVED_
SWITCH_3_BI
T15-0&RESER
VED_SWITCH
_3_BIT16-0&R
ESERVED_SW
ITCH_3_BIT17
-0&RESERVE
Issue 02 (2013-09-30)
42
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
D_SWITCH_3_
BIT18-0&RES
ERVED_SWIT
CH_3_BIT19-0
&RESERVED_
SWITCH_3_BI
T20-0&RESER
VED_SWITCH
_3_BIT21-0&R
ESERVED_SW
ITCH_3_BIT22
-0&RESERVE
D_SWITCH_3_
BIT23-0&RES
ERVED_SWIT
CH_3_BIT24-0
&RESERVED_
SWITCH_3_BI
T25-0&RESER
VED_SWITCH
_3_BIT26-0&R
ESERVED_SW
ITCH_3_BIT27
-0&RESERVE
D_SWITCH_3_
BIT28-0&RES
ERVED_SWIT
CH_3_BIT29-0
&RESERVED_
SWITCH_3_BI
T30-0&RESER
VED_SWITCH
_3_BIT31-0&R
ESERVED_SW
ITCH_3_BIT32
-0
Issue 02 (2013-09-30)
43
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RsvSwitch3
BSC6910
SET
UALGORSVP
ARA
None
None
Meaning:RRM
algorithm
reserved U32
Switch Para 3.
The 32-bit
parameter is
reserved for
further change
request use.
Disuse
statement: This
parameter is
used
temporarily in
patch versions
and will be
replaced with a
new parameter
in later versions.
The new
parameter ID
reflects the
parameter
function.
Therefore, this
parameter is not
recommended
for the
configuration
interface.
GUI Value
Range:RESER
VED_SWITCH
_3_BIT1,
RESERVED_S
WITCH_3_BIT
2,
RESERVED_S
WITCH_3_BIT
3,
RESERVED_S
WITCH_3_BIT
4,
RESERVED_S
WITCH_3_BIT
5,
RESERVED_S
Issue 02 (2013-09-30)
44
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
WITCH_3_BIT
6,
RESERVED_S
WITCH_3_BIT
7,
RESERVED_S
WITCH_3_BIT
8,
RESERVED_S
WITCH_3_BIT
9,
RESERVED_S
WITCH_3_BIT
10,
RESERVED_S
WITCH_3_BIT
11,
RESERVED_S
WITCH_3_BIT
12,
RESERVED_S
WITCH_3_BIT
13,
RESERVED_S
WITCH_3_BIT
14,
RESERVED_S
WITCH_3_BIT
15,
RESERVED_S
WITCH_3_BIT
16,
RESERVED_S
WITCH_3_BIT
17,
RESERVED_S
WITCH_3_BIT
18,
RESERVED_S
WITCH_3_BIT
19,
RESERVED_S
WITCH_3_BIT
20,
RESERVED_S
WITCH_3_BIT
21,
RESERVED_S
Issue 02 (2013-09-30)
45
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
WITCH_3_BIT
22,
RESERVED_S
WITCH_3_BIT
23,
RESERVED_S
WITCH_3_BIT
24,
RESERVED_S
WITCH_3_BIT
25,
RESERVED_S
WITCH_3_BIT
26,
RESERVED_S
WITCH_3_BIT
27,
RESERVED_S
WITCH_3_BIT
28,
RESERVED_S
WITCH_3_BIT
29,
RESERVED_S
WITCH_3_BIT
30,
RESERVED_S
WITCH_3_BIT
31,
RESERVED_S
WITCH_3_BIT
32
Unit:None
Actual Value
Range:RESER
VED_SWITCH
_3_BIT1,
RESERVED_S
WITCH_3_BIT
2,
RESERVED_S
WITCH_3_BIT
3,
RESERVED_S
WITCH_3_BIT
4,
RESERVED_S
Issue 02 (2013-09-30)
46
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
WITCH_3_BIT
5,
RESERVED_S
WITCH_3_BIT
6,
RESERVED_S
WITCH_3_BIT
7,
RESERVED_S
WITCH_3_BIT
8,
RESERVED_S
WITCH_3_BIT
9,
RESERVED_S
WITCH_3_BIT
10,
RESERVED_S
WITCH_3_BIT
11,
RESERVED_S
WITCH_3_BIT
12,
RESERVED_S
WITCH_3_BIT
13,
RESERVED_S
WITCH_3_BIT
14,
RESERVED_S
WITCH_3_BIT
15,
RESERVED_S
WITCH_3_BIT
16,
RESERVED_S
WITCH_3_BIT
17,
RESERVED_S
WITCH_3_BIT
18,
RESERVED_S
WITCH_3_BIT
19,
RESERVED_S
WITCH_3_BIT
20,
RESERVED_S
Issue 02 (2013-09-30)
47
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
WITCH_3_BIT
21,
RESERVED_S
WITCH_3_BIT
22,
RESERVED_S
WITCH_3_BIT
23,
RESERVED_S
WITCH_3_BIT
24,
RESERVED_S
WITCH_3_BIT
25,
RESERVED_S
WITCH_3_BIT
26,
RESERVED_S
WITCH_3_BIT
27,
RESERVED_S
WITCH_3_BIT
28,
RESERVED_S
WITCH_3_BIT
29,
RESERVED_S
WITCH_3_BIT
30,
RESERVED_S
WITCH_3_BIT
31,
RESERVED_S
WITCH_3_BIT
32
Default
Value:RESERV
ED_SWITCH_
3_BIT1-0&RES
ERVED_SWIT
CH_3_BIT2-0&
RESERVED_S
WITCH_3_BIT
3-0&RESERVE
D_SWITCH_3_
BIT4-0&RESE
RVED_SWITC
Issue 02 (2013-09-30)
48
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
H_3_BIT5-0&R
ESERVED_SW
ITCH_3_BIT60&RESERVED
_SWITCH_3_B
IT7-0&RESER
VED_SWITCH
_3_BIT8-0&RE
SERVED_SWI
TCH_3_BIT9-0
&RESERVED_
SWITCH_3_BI
T10-0&RESER
VED_SWITCH
_3_BIT11-0&R
ESERVED_SW
ITCH_3_BIT12
-0&RESERVE
D_SWITCH_3_
BIT13-0&RES
ERVED_SWIT
CH_3_BIT14-0
&RESERVED_
SWITCH_3_BI
T15-0&RESER
VED_SWITCH
_3_BIT16-0&R
ESERVED_SW
ITCH_3_BIT17
-0&RESERVE
D_SWITCH_3_
BIT18-0&RES
ERVED_SWIT
CH_3_BIT19-0
&RESERVED_
SWITCH_3_BI
T20-0&RESER
VED_SWITCH
_3_BIT21-0&R
ESERVED_SW
ITCH_3_BIT22
-0&RESERVE
D_SWITCH_3_
BIT23-0&RES
ERVED_SWIT
CH_3_BIT24-0
&RESERVED_
SWITCH_3_BI
Issue 02 (2013-09-30)
49
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
T25-0&RESER
VED_SWITCH
_3_BIT26-0&R
ESERVED_SW
ITCH_3_BIT27
-0&RESERVE
D_SWITCH_3_
BIT28-0&RES
ERVED_SWIT
CH_3_BIT29-0
&RESERVED_
SWITCH_3_BI
T30-0&RESER
VED_SWITCH
_3_BIT31-0&R
ESERVED_SW
ITCH_3_BIT32
-0
Issue 02 (2013-09-30)
50
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PROCESSSWI
TCH
BSC6900
ADD
UCNNODE
WRFD-021304
RAN Sharing
Introduction
Package
Meaning:1)
IUFLEX_NOT_
SEL_BLOCK_
SWITCH
Whether the
RNC forwards
the INITIAL UE
MESSAGE
message to a CN
node in Iu Flex
networking
when the status
of the CN node
is NORMAL on
the RNC. 1: This
switch is turned
on. The status of
the CN node is
changed from
NORMAL to
BLOCK, and the
RNC forwards
only the
INITIAL UE
MESSAGE
message with
cause value
"paging
response" to the
CN node. 0: This
switch is turned
off. The status of
the CN node is
unchanged. 2)
REL7_QOS_H
ANDLE_SWIT
CH(Release 7
Qos Parameter
handle switch)
Whether the CN
Node need send
R7 Qos
parameter to
UE. 1:This
switch is turned
on.Element
"Higher bitrates
than 16 Mbps
MOD
UCNNODE
Issue 02 (2013-09-30)
51
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
flag" will added
to the Initial UE
Message by
RNC. 0:This
switch is turned
off.Element
"Higher bitrates
than 16 Mbps
flag" will not
added to the
Initial UE
Message by
RNC.
GUI Value
Range:IUFLEX
_NOT_SEL_BL
OCK_SWITCH
(IUFLEX_NOT
_SEL_BLOCK
_SWITCH),
REL7_QOS_H
ANDLE_SWIT
CH
(REL7_QOS_H
ANDLE_SWIT
CH)
Unit:None
Actual Value
Range:This
parameter is set
to 0 or 1
according to the
related domains.
Default
Value:IUFLEX
_NOT_SEL_BL
OCK_SWITCH
-0,
REL7_QOS_H
ANDLE_SWIT
CH-0
Issue 02 (2013-09-30)
52
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PROCESSSWI
TCH
BSC6910
ADD
UCNNODE
WRFD-021304
RAN Sharing
Introduction
Package
Meaning:1)
IUFLEX_NOT_
SEL_BLOCK_
SWITCH
Whether the
RNC forwards
the INITIAL UE
MESSAGE
message to a CN
node in Iu Flex
networking
when the status
of the CN node
is NORMAL on
the RNC. 1: This
switch is turned
on. The status of
the CN node is
changed from
NORMAL to
BLOCK, and the
RNC forwards
only the
INITIAL UE
MESSAGE
message with
cause value
"paging
response" to the
CN node. 0: This
switch is turned
off. The status of
the CN node is
unchanged. 2)
REL7_QOS_H
ANDLE_SWIT
CH(Release 7
Qos Parameter
handle switch)
Whether the CN
Node need send
R7 Qos
parameter to
UE. 1:This
switch is turned
on.Element
"Higher bitrates
than 16 Mbps
MOD
UCNNODE
Issue 02 (2013-09-30)
53
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
flag" will added
to the Initial UE
Message by
RNC. 0:This
switch is turned
off.Element
"Higher bitrates
than 16 Mbps
flag" will not
added to the
Initial UE
Message by
RNC.
GUI Value
Range:IUFLEX
_NOT_SEL_BL
OCK_SWITCH
(IUFLEX_NOT
_SEL_BLOCK
_SWITCH),
REL7_QOS_H
ANDLE_SWIT
CH
(REL7_QOS_H
ANDLE_SWIT
CH)
Unit:None
Actual Value
Range:This
parameter is set
to 0 or 1
according to the
related domains.
Default
Value:IUFLEX
_NOT_SEL_BL
OCK_SWITCH
-0,
REL7_QOS_H
ANDLE_SWIT
CH-0
Issue 02 (2013-09-30)
54
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
NRI
BSC6900
ADD
UNRIGLBCNI
DMAP
WRFD-021302
Iu Flex
WRFD-021311
MOCN
Introduction
Package
Meaning:Identifying a Network
resourse: 1. The
NRI numbers of
CS domain and
PS domain are
independent
from each other.
2. If multiple
pool areas
overlap, the NRI
uniquely
identify all the
CN nodes
connected to it.
3. A CN node
can have
multiple NRIs.
In one pool area,
however, an
NRI can only
correspond to
one CN node.
An NRI
uniquely
identifies a CN
node that serves
a pool area. The
value range of
NRI is variable.
The value range
depends on the
scale of a CN
domain and
expansion
requirements.
The maximum
number of NRIs
is 1,024. For
example, a CS
domain has a
maximum of 16
nodes. In this
case, Length of
CS NRI in bits is
set to 4, which
indicates that an
NRI is
RMV
UNRIGLBCNI
DMAP
Issue 02 (2013-09-30)
55
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
represented by
four binary
digits.
Therefore, the
value range of
NRI is 0 to 15.
GUI Value
Range:0~1023
Unit:None
Actual Value
Range:0~1023
Default
Value:None
Issue 02 (2013-09-30)
56
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
NRI
BSC6910
ADD
UNRIGLBCNI
DMAP
WRFD-021302
Iu Flex
WRFD-021311
MOCN
Introduction
Package
Meaning:Identifying a Network
resourse: 1. The
NRI numbers of
CS domain and
PS domain are
independent
from each other.
2. If multiple
pool areas
overlap, the NRI
uniquely
identify all the
CN nodes
connected to it.
3. A CN node
can have
multiple NRIs.
In one pool area,
however, an
NRI can only
correspond to
one CN node.
An NRI
uniquely
identifies a CN
node that serves
a pool area. The
value range of
NRI is variable.
The value range
depends on the
scale of a CN
domain and
expansion
requirements.
The maximum
number of NRIs
is 1,024. For
example, a CS
domain has a
maximum of 16
nodes. In this
case, Length of
CS NRI in bits is
set to 4, which
indicates that an
NRI is
RMV
UNRIGLBCNI
DMAP
Issue 02 (2013-09-30)
57
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
represented by
four binary
digits.
Therefore, the
value range of
NRI is 0 to 15.
GUI Value
Range:0~1023
Unit:None
Actual Value
Range:0~1023
Default
Value:None
AvailCap
BSC6900
ADD
UCNNODE
MOD
UCNNODE
WRFD-021306
WRFD-021311
Iu Flex Load
Distribution
Management
MOCN
Introduction
Package
Meaning:This
parameter is
used to
configure the
relative capacity
of each CN node
in Iu-Flex
scenarios. If a
user cannot
select a CN node
based on the
NNSF, a CN
node needs to be
selected among
all the available
CN nodes
according to the
proportions
generated based
on CN node
capacity.
GUI Value
Range:0~65535
Unit:None
Actual Value
Range:
0~65535000
step:1000
Default
Value:None
Issue 02 (2013-09-30)
58
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
AvailCap
BSC6910
ADD
UCNNODE
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:This
parameter is
used to
configure the
relative capacity
of each CN node
in Iu-Flex
scenarios. If a
user cannot
select a CN node
based on the
NNSF, a CN
node needs to be
selected among
all the available
CN nodes
according to the
proportions
generated based
on CN node
capacity.
WRFD-021311
MOD
UCNNODE
MOCN
Introduction
Package
GUI Value
Range:0~65535
Unit:None
Actual Value
Range:
0~65535000
step:1000
Default
Value:None
CsInfoUpdFlag
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Indicat
ing whether the
CS domain
permits the CN
information to
update .
GUI Value
Range:OFF, ON
Unit:None
Actual Value
Range:OFF, ON
Default
Value:OFF
Issue 02 (2013-09-30)
59
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CsInfoUpdFlag
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Indicat
ing whether the
CS domain
permits the CN
information to
update .
GUI Value
Range:OFF, ON
Unit:None
Actual Value
Range:OFF, ON
Default
Value:OFF
PsInfoUpdFlag
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Indicat
ing whether the
PS domain
permits the CN
information to
update .
GUI Value
Range:OFF, ON
Unit:None
Actual Value
Range:OFF, ON
Default
Value:OFF
PsInfoUpdFlag
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Indicat
ing whether the
PS domain
permits the CN
information to
update .
GUI Value
Range:OFF, ON
Unit:None
Actual Value
Range:OFF, ON
Default
Value:OFF
Issue 02 (2013-09-30)
60
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNLoadStatus
BSC6900
ADD
UCNNODE
WRFD-021306
MOD
UCNNODE
MRFD-211502
Iu Flex Load
Distribution
Management
Meaning:Status
of a CN node.
The status needs
to be negotiated
with the CN and
is configured
through the
MML
command. A CN
node can be
configured with
the following
status: 1.
Normal: This
value indicates
that the UE can
access the CN
node normally.
2. Offload: If the
UE carries
"NullNRI"("SE
T
UOPERATOR
CFGPARA") in
the Initial Direct
transfer
message, the UE
cannot access
the CN node. If
the UE carries
NRI but not
"NullNRI" in the
Initial Direct
transfer
message, the UE
can access the
CN node. 3.
Inhibited: This
value indicates
that the UE
cannot access
the CN node
normally.
WRFD-021311
MOCN
Introduction
Package
IP-Based BSC
and RNC CoTransmission on
MBSC Side
GUI Value
Range:NORMA
L, OFFLOAD,
INHIBITED
Issue 02 (2013-09-30)
61
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
Unit:None
Actual Value
Range:NORMA
L, OFFLOAD,
INHIBITED
Default
Value:None
Issue 02 (2013-09-30)
62
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNLoadStatus
BSC6910
ADD
UCNNODE
WRFD-021306
MOD
UCNNODE
MRFD-211502
Iu Flex Load
Distribution
Management
Meaning:Status
of a CN node.
The status needs
to be negotiated
with the CN and
is configured
through the
MML
command. A CN
node can be
configured with
the following
status: 1.
Normal: This
value indicates
that the UE can
access the CN
node normally.
2. Offload: If the
UE carries
"NullNRI"("SE
T
UOPERATOR
CFGPARA") in
the Initial Direct
transfer
message, the UE
cannot access
the CN node. If
the UE carries
NRI but not
"NullNRI" in the
Initial Direct
transfer
message, the UE
can access the
CN node. 3.
Inhibited: This
value indicates
that the UE
cannot access
the CN node
normally.
WRFD-021311
MOCN
Introduction
Package
IP-Based BSC
and RNC CoTransmission on
MBSC Side
GUI Value
Range:NORMA
L, OFFLOAD,
INHIBITED
Issue 02 (2013-09-30)
63
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
Unit:None
Actual Value
Range:NORMA
L, OFFLOAD,
INHIBITED
Default
Value:None
CsNriCfgMode
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021304
WRFD-021311
WRFD-021302
WRFD-021306
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
Iu Flex
Iu Flex Load
Distribution
Management
Meaning:This
parameter
specifies feature
mode of
operators in the
CS domain. You
should
configure the
network
resource
identifier (NRI)
when MOCN or
Iu-Flex is
supported.
GUI Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Unit:None
Actual Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Default
Value:SUPP_N
ONE
Issue 02 (2013-09-30)
64
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CsNriCfgMode
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021304
RAN Sharing
Introduction
Package
Meaning:This
parameter
specifies feature
mode of
operators in the
CS domain. You
should
configure the
network
resource
identifier (NRI)
when MOCN or
Iu-Flex is
supported.
WRFD-021311
WRFD-021302
WRFD-021306
MOCN
Introduction
Package
Iu Flex
Iu Flex Load
Distribution
Management
GUI Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Unit:None
Actual Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Default
Value:SUPP_N
ONE
Issue 02 (2013-09-30)
65
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PsNriCfgMode
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021302
Iu Flex
WRFD-021311
MOCN
Introduction
Package
Meaning:This
parameter
specifies feature
mode of
operators in the
PS domain. You
should
configure the
network
resource
identifier (NRI)
when MOCN or
Iu-Flex is
supported.
WRFD-021306
Iu Flex Load
Distribution
Management
GUI Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Unit:None
Actual Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Default
Value:SUPP_N
ONE
Issue 02 (2013-09-30)
66
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PsNriCfgMode
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021302
Iu Flex
WRFD-021311
MOCN
Introduction
Package
Meaning:This
parameter
specifies feature
mode of
operators in the
PS domain. You
should
configure the
network
resource
identifier (NRI)
when MOCN or
Iu-Flex is
supported.
WRFD-021306
Iu Flex Load
Distribution
Management
GUI Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Unit:None
Actual Value
Range:SUPP_N
ONE,
SUPP_IUFLEX
, SUPP_MOCN,
SUPP_IUFLEX
_MOCN
Default
Value:SUPP_N
ONE
CSNRILength
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021304
WRFD-021311
WRFD-021302
WRFD-021306
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
Iu Flex
Iu Flex Load
Distribution
Management
Meaning:Netwo
rk Resource
Identity(NRI)
length for CS
domain.
GUI Value
Range:1~10
Unit:None
Actual Value
Range:1~10
Default
Value:None
Issue 02 (2013-09-30)
67
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CSNRILength
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021304
RAN Sharing
Introduction
Package
Meaning:Netwo
rk Resource
Identity(NRI)
length for CS
domain.
WRFD-021311
WRFD-021302
WRFD-021306
MOCN
Introduction
Package
Iu Flex
Iu Flex Load
Distribution
Management
GUI Value
Range:1~10
Unit:None
Actual Value
Range:1~10
Default
Value:None
PSNRILength
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021302
Iu Flex
WRFD-021311
MOCN
Introduction
Package
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Netwo
rk Resource
Identity(NRI)
length for PS
domain.
GUI Value
Range:1~10
Unit:None
Actual Value
Range:1~10
Default
Value:None
PSNRILength
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021302
Iu Flex
WRFD-021311
MOCN
Introduction
Package
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Netwo
rk Resource
Identity(NRI)
length for PS
domain.
GUI Value
Range:1~10
Unit:None
Actual Value
Range:1~10
Default
Value:None
Issue 02 (2013-09-30)
68
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CnOpIndex
BSC6900
ADD
UCNNODE
WRFD-021304
MOD
UCNNODE
WRFD-020127
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
GUI Value
Range:0~3
Warning of
Disaster
Actual Value
Range:0~3
Dedicated
Carrier for Each
Operator
Default
Value:None
RMV
UCNNODE
WRFD-021311
WRFD-021304
01
WRFD-021302
Unit:None
Iu Flex
CnOpIndex
BSC6910
ADD
UCNNODE
WRFD-021304
MOD
UCNNODE
WRFD-020127
RMV
UCNNODE
WRFD-021311
WRFD-021304
01
WRFD-021302
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
GUI Value
Range:0~3
Warning of
Disaster
Actual Value
Range:0~3
Dedicated
Carrier for Each
Operator
Default
Value:None
Unit:None
Iu Flex
Issue 02 (2013-09-30)
69
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNId
BSC6900
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
MOD
UCNNODE
WRFD-021302
Meaning:Identifying a CN
Node. When the
Iu-Flex feature
is enabled, a
maximum of 32
CN nodes can be
configured in
each CN
domain, either
the CS domain
or the PS
domain. CN
nodes are
uniquely but not
necessarily
consecutively
numbered
within a RNC.
For example, set
the number of a
CN node to 0
and that of
another CN
node to 2. Note:
Although the
number of a CN
node ranges
from 0 to 4095, a
maximum of 64
CN nodes can be
configured.
RMV
UCNNODE
WRFD-021311
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~4095
Unit:None
Actual Value
Range:0~4095
Default
Value:None
Issue 02 (2013-09-30)
70
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNId
BSC6910
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
MOD
UCNNODE
WRFD-021302
Meaning:Identifying a CN
Node. When the
Iu-Flex feature
is enabled, a
maximum of 64
CN nodes can be
configured in
each CN
domain, either
the CS domain
or the PS
domain. CN
nodes are
uniquely but not
necessarily
consecutively
numbered
within a RNC.
For example, set
the number of a
CN node to 0
and that of
another CN
node to 2. Note:
Although the
number of a CN
node ranges
from 0 to 4095, a
maximum of
128 CN nodes
can be
configured.
RMV
UCNNODE
WRFD-021311
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~4095
Unit:None
Actual Value
Range:0~4095
Default
Value:None
Issue 02 (2013-09-30)
71
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNDomainId
BSC6900
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
MOD
UCNNODE
MRFD-211502
WRFD-021101
WRFD-021311
WRFD-040202
Dynamic
Channel
Configuration
Control (DCCC)
IP-Based BSC
and RNC CoTransmission on
MBSC Side
MOCN
Introduction
Package
RNC Node
Redundancy
CNDomainId
BSC6910
ADD
UCNNODE
WRFD-010101
MOD
UCNNODE
MRFD-211502
WRFD-021101
WRFD-021311
3GPP R9
Specifications
Dynamic
Channel
Configuration
Control (DCCC)
IP-Based BSC
and RNC CoTransmission on
MBSC Side
MOCN
Introduction
Package
Dpx
BSC6900
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
MOD
UCNNODE
GUI Value
Range:CS_DO
MAIN,
PS_DOMAIN
Unit:None
Actual Value
Range:CS_DO
MAIN,
PS_DOMAIN
Default
Value:None
Meaning:Identifying the type of
a CN.
GUI Value
Range:CS_DO
MAIN,
PS_DOMAIN
Unit:None
Actual Value
Range:CS_DO
MAIN,
PS_DOMAIN
Default
Value:None
Meaning:DSP
index. This
parameter
uniquely
identifies a peer
DSP.
GUI Value
Range:0~186
Unit:None
Actual Value
Range:0~186
Default
Value:None
Issue 02 (2013-09-30)
72
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
Dpx
BSC6910
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
Meaning:DSP
index. This
parameter
uniquely
identifies a peer
DSP.
MOD
UCNNODE
GUI Value
Range:0~427
Unit:None
Actual Value
Range:0~427
Default
Value:None
CNProtclVer
BSC6900
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
MOD
UCNNODE
Meaning:Protoc
ol version
supported by the
CN. This
parameter is
modified based
on the actual
protocol version
of the CN when
the CN protocol
version upgrade,
otherwise it will
cause some
features
supported by the
new protocol
version
unavailable.
GUI Value
Range:R99, R4,
R5, R6, R7, R8,
R9, R10
Unit:None
Actual Value
Range:R99, R4,
R5, R6, R7, R8,
R9, R10
Default
Value:None
Issue 02 (2013-09-30)
73
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNProtclVer
BSC6910
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
Meaning:Protoc
ol version
supported by the
CN. This
parameter is
modified based
on the actual
protocol version
of the CN when
the CN protocol
version upgrade,
otherwise it will
cause some
features
supported by the
new protocol
version
unavailable.
MOD
UCNNODE
GUI Value
Range:R99, R4,
R5, R6, R7, R8,
R9, R10
Unit:None
Actual Value
Range:R99, R4,
R5, R6, R7, R8,
R9, R10
Default
Value:None
TnlBearerType
BSC6900
ADD
UCNNODE
MOD
UCNNODE
WRFD-050301
WRFD-050409
ATM
Transmission
Introduction
Package
Meaning:The
transfers bearer
type of Iu
interface.
IP Transmission
Introduction on
Iu Interface
GUI Value
Range:ATM_T
RANS,
IP_TRANS
Unit:None
Actual Value
Range:ATM_T
RANS,
IP_TRANS
Default
Value:None
Issue 02 (2013-09-30)
74
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
TnlBearerType
BSC6910
ADD
UCNNODE
WRFD-050301
ATM
Transmission
Introduction
Package
Meaning:The
transfers bearer
type of Iu
interface.
Iu/Iur IP
Transmission
Based on
Dynamic Load
Balance
GUI Value
Range:ATM_T
RANS,
IP_TRANS
MOD
UCNNODE
WRFD-150244
Unit:None
Actual Value
Range:ATM_T
RANS,
IP_TRANS
Default
Value:None
Issue 02 (2013-09-30)
75
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
Switch3GPP254
15CR0125
BSC6900
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
Meaning:Wheth
er to enable
functions
defined in 3GPP
25.415 CR0125
during CS
services. When
this switch is
turned on, the
maximum rate
for the reverse
direction is
included in the
ACK message
specific to the Iu
UP rate control
procedure for
AMR services.
When this
switch is turned
off, the
maximum rate
for the current
direction is
included in the
previous
message. If the
parameter
setting on the
RNC side is
inconsistent
with the
parameter
setting on the
CN side,
exceptions will
occur in Iu UP
rate control
procedure,
leading to
deteriorated CS
speech
quality.For
details about the
previously
mentioned
functions, see
MOD
UCNNODE
Issue 02 (2013-09-30)
76
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
3GPP 25.415
CR0125.
GUI Value
Range:OFF, ON
Unit:None
Actual Value
Range:OFF, ON
Default
Value:None
Issue 02 (2013-09-30)
77
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
Switch3GPP254
15CR0125
BSC6910
ADD
UCNNODE
WRFD-010101
3GPP R9
Specifications
Meaning:Wheth
er to enable
functions
defined in 3GPP
25.415 CR0125
during CS
services. When
this switch is
turned on, the
maximum rate
for the reverse
direction is
included in the
ACK message
specific to the Iu
UP rate control
procedure for
AMR services.
When this
switch is turned
off, the
maximum rate
for the current
direction is
included in the
previous
message. If the
parameter
setting on the
RNC side is
inconsistent
with the
parameter
setting on the
CN side,
exceptions will
occur in Iu UP
rate control
procedure,
leading to
deteriorated CS
speech
quality.For
details about the
previously
mentioned
functions, see
MOD
UCNNODE
Issue 02 (2013-09-30)
78
WCDMA RAN
Iu Flex Feature Parameter Description
Parameter ID
NE
9 Parameters
MML
Command
Feature ID
Feature Name
Description
3GPP 25.415
CR0125.
GUI Value
Range:OFF, ON
Unit:None
Actual Value
Range:OFF, ON
Default
Value:None
CnOpIndex
BSC6900
ADD
UNRIGLBCNI
DMAP
RMV
UNRIGLBCNI
DMAP
WRFD-021304
WRFD-021311
WRFD-020127
WRFD-021304
01
WRFD-021302
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
GUI Value
Range:0~3
Warning of
Disaster
Actual Value
Range:0~3
Dedicated
Carrier for Each
Operator
Default
Value:None
Unit:None
Iu Flex
CnOpIndex
BSC6910
ADD
UNRIGLBCNI
DMAP
RMV
UNRIGLBCNI
DMAP
WRFD-021304
WRFD-021311
WRFD-020127
WRFD-021304
01
WRFD-021302
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
GUI Value
Range:0~3
Warning of
Disaster
Actual Value
Range:0~3
Dedicated
Carrier for Each
Operator
Default
Value:None
Unit:None
Iu Flex
Issue 02 (2013-09-30)
79
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNId
BSC6900
ADD
UNRIGLBCNI
DMAP
WRFD-010101
3GPP R9
Specifications
Meaning:Identifying a CN
Node. When the
Iu-Flex feature
is enabled, a
maximum of 32
CN nodes can be
configured in
each CN
domain, either
the CS domain
or the PS
domain. CN
nodes are
uniquely but not
necessarily
consecutively
numbered
within a RNC.
For example, set
the number of a
CN node to 0
and that of
another CN
node to 2. Note:
Although the
number of a CN
node ranges
from 0 to 4095, a
maximum of 64
CN nodes can be
configured.
RMV
UNRIGLBCNI
DMAP
WRFD-021311
WRFD-021302
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~4095
Unit:None
Actual Value
Range:0~4095
Default
Value:None
Issue 02 (2013-09-30)
80
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNId
BSC6910
ADD
UNRIGLBCNI
DMAP
WRFD-010101
3GPP R9
Specifications
Meaning:Identifying a CN
Node. When the
Iu-Flex feature
is enabled, a
maximum of 64
CN nodes can be
configured in
each CN
domain, either
the CS domain
or the PS
domain. CN
nodes are
uniquely but not
necessarily
consecutively
numbered
within a RNC.
For example, set
the number of a
CN node to 0
and that of
another CN
node to 2. Note:
Although the
number of a CN
node ranges
from 0 to 4095, a
maximum of
128 CN nodes
can be
configured.
RMV
UNRIGLBCNI
DMAP
WRFD-021311
WRFD-021302
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~4095
Unit:None
Actual Value
Range:0~4095
Default
Value:None
Issue 02 (2013-09-30)
81
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
ImsiRtMin
BSC6900
ADD
UIMSIIDNNSC
NIDMAP
WRFD-021304
RAN Sharing
Introduction
Package
Meaning:Minim
um of IMSI
route parameter
in Intra Domain
NAS Node
Selector
(IDNNS).
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021311
WRFD-021302
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~999
Unit:None
Actual Value
Range:0~999
Default
Value:None
ImsiRtMin
BSC6910
ADD
UIMSIIDNNSC
NIDMAP
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021304
WRFD-021311
WRFD-021302
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
Iu Flex
Meaning:Minim
um of IMSI
route parameter
in Intra Domain
NAS Node
Selector
(IDNNS).
GUI Value
Range:0~999
Unit:None
Actual Value
Range:0~999
Default
Value:None
ImsiRtMax
BSC6900
ADD
UIMSIIDNNSC
NIDMAP
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021304
WRFD-021311
WRFD-021302
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
Iu Flex
Meaning:Maxi
mum of IMSI
route parameter
in Intra Domain
NAS Node
Selector
(IDNNS).
GUI Value
Range:0~999
Unit:None
Actual Value
Range:0~999
Default
Value:None
Issue 02 (2013-09-30)
82
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
ImsiRtMax
BSC6910
ADD
UIMSIIDNNSC
NIDMAP
WRFD-021304
RAN Sharing
Introduction
Package
Meaning:Maxi
mum of IMSI
route parameter
in Intra Domain
NAS Node
Selector
(IDNNS).
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021311
WRFD-021302
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~999
Unit:None
Actual Value
Range:0~999
Default
Value:None
CnOpIndex
BSC6900
ADD
UIMSIIDNNSC
NIDMAP
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021304
WRFD-021311
WRFD-020127
WRFD-021304
01
WRFD-021302
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
GUI Value
Range:0~3
Warning of
Disaster
Actual Value
Range:0~3
Dedicated
Carrier for Each
Operator
Default
Value:None
Unit:None
Iu Flex
CnOpIndex
BSC6910
ADD
UIMSIIDNNSC
NIDMAP
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021304
WRFD-021311
WRFD-020127
WRFD-021304
01
WRFD-021302
RAN Sharing
Introduction
Package
MOCN
Introduction
Package
GUI Value
Range:0~3
Warning of
Disaster
Actual Value
Range:0~3
Dedicated
Carrier for Each
Operator
Default
Value:None
Unit:None
Iu Flex
Issue 02 (2013-09-30)
83
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNId
BSC6900
ADD
UIMSIIDNNSC
NIDMAP
WRFD-010101
3GPP R9
Specifications
Meaning:Identifying a CN
Node. When the
Iu-Flex feature
is enabled, a
maximum of 32
CN nodes can be
configured in
each CN
domain, either
the CS domain
or the PS
domain. CN
nodes are
uniquely but not
necessarily
consecutively
numbered
within a RNC.
For example, set
the number of a
CN node to 0
and that of
another CN
node to 2. Note:
Although the
number of a CN
node ranges
from 0 to 4095, a
maximum of 64
CN nodes can be
configured.
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021311
WRFD-021302
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~4095
Unit:None
Actual Value
Range:0~4095
Default
Value:None
Issue 02 (2013-09-30)
84
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNId
BSC6910
ADD
UIMSIIDNNSC
NIDMAP
WRFD-010101
3GPP R9
Specifications
Meaning:Identifying a CN
Node. When the
Iu-Flex feature
is enabled, a
maximum of 64
CN nodes can be
configured in
each CN
domain, either
the CS domain
or the PS
domain. CN
nodes are
uniquely but not
necessarily
consecutively
numbered
within a RNC.
For example, set
the number of a
CN node to 0
and that of
another CN
node to 2. Note:
Although the
number of a CN
node ranges
from 0 to 4095, a
maximum of
128 CN nodes
can be
configured.
RMV
UIMSIIDNNSC
NIDMAP
WRFD-021311
WRFD-021302
MOCN
Introduction
Package
Iu Flex
GUI Value
Range:0~4095
Unit:None
Actual Value
Range:0~4095
Default
Value:None
Issue 02 (2013-09-30)
85
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PsInfoUpdTmr
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Protec
tive timer for
synchronization
updates in the PS
domain. When
the RNC
receives
capacity
synchronization
update
instructions for
all CN nodes in
the PS domain
before the timer
expires, the
RNC updates
the local CN
node capacity
information.
Otherwise, the
RNC does not
update this
information.
GUI Value
Range:60~900
Unit:s
Actual Value
Range:60~900
Default Value:
900
Issue 02 (2013-09-30)
86
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PsInfoUpdTmr
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Protec
tive timer for
synchronization
updates in the PS
domain. When
the RNC
receives
capacity
synchronization
update
instructions for
all CN nodes in
the PS domain
before the timer
expires, the
RNC updates
the local CN
node capacity
information.
Otherwise, the
RNC does not
update this
information.
GUI Value
Range:60~900
Unit:s
Actual Value
Range:60~900
Default Value:
900
Issue 02 (2013-09-30)
87
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
NullNRI
BSC6900
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Null
network
resource
identifier (NRI),
which relates to
the non-access
stratum (NAS)
node selection
function
(NNSF). When
NullNRIOptSwi
tch is turned off
and the CN node
corresponding
to the parameter
value is
overloaded, UEs
must be
reallocated to
other CN
nodes.When
NullNRIOptSwi
tch is turned on
and the CS CN
node
corresponding
to the parameter
value is
overloaded, UEs
must be
reallocated to
other CS CN
nodes.
WRFD-021311
MOCN
Introduction
Package
GUI Value
Range:0~1023
Unit:None
Actual Value
Range:0~1023
Default
Value:None
Issue 02 (2013-09-30)
88
WCDMA RAN
Iu Flex Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
NullNRI
BSC6910
SET
UOPERATOR
CFGPARA
WRFD-021306
Iu Flex Load
Distribution
Management
Meaning:Null
network
resource
identifier (NRI),
which relates to
the non-access
stratum (NAS)
node selection
function
(NNSF). When
NullNRIOptSwi
tch is turned off
and the CN node
corresponding
to the parameter
value is
overloaded, UEs
must be
reallocated to
other CN
nodes.When
NullNRIOptSwi
tch is turned on
and the CS CN
node
corresponding
to the parameter
value is
overloaded, UEs
must be
reallocated to
other CS CN
nodes.
WRFD-021311
MOCN
Introduction
Package
GUI Value
Range:0~1023
Unit:None
Actual Value
Range:0~1023
Default
Value:None
Issue 02 (2013-09-30)
89
WCDMA RAN
Iu Flex Feature Parameter Description
10 Counters
10
Counters
Counter Name
Counter
Description
NE
Feature ID
Feature Name
67192538
VS.IU.LdBalRt
CS.IMSI
Number of
Times that CS
Load Balancing
is Performed by
IMSI Users
BSC6900
WRFD-021306
Iu Flex Load
Distribution
Management
67192539
VS.IU.LdBalRt
CS.InValidNRI
Number of
Times that CS
Load Balancing
is Performed by
TMSI Users
Due to Invalid
NRI
BSC6900
WRFD-021306
Iu Flex Load
Distribution
Management
67192540
VS.IU.LdBalRt
CS.IMEI
Number of
Times that CS
Load Balancing
is Performed by
IMEI Users
BSC6900
WRFD-021306
Iu Flex Load
Distribution
Management
67192541
VS.IU.Load.Ro
utePS.IMSI
Number of
Performed PS
Load Balancing
by IMSI Users
BSC6900
WRFD-021306
Iu Flex Load
Distribution
Management
67192542
VS.IU.Load.Ro
utePS.NRI
Number of
Performed PS
Load Balancing
by TMSI Users
Due to Invalid
NRI
BSC6900
WRFD-021306
Iu Flex Load
Distribution
Management
Issue 02 (2013-09-30)
90
WCDMA RAN
Iu Flex Feature Parameter Description
10 Counters
Counter ID
Counter Name
Counter
Description
NE
Feature ID
Feature Name
67192543
VS.IU.Load.Ro
utePS.IMEI
Number of
Performed PS
Load Balancing
by IMEI Users
BSC6900
WRFD-021306
Iu Flex Load
Distribution
Management
67192538
VS.IU.LdBalRt
CS.IMSI
Number of
Times that CS
Load Balancing
is Performed by
IMSI Users
BSC6910
WRFD-021306
Iu Flex Load
Distribution
Management
67192539
VS.IU.LdBalRt
CS.InValidNRI
Number of
Times that CS
Load Balancing
is Performed by
TMSI Users
Due to Invalid
NRI
BSC6910
WRFD-021306
Iu Flex Load
Distribution
Management
67192540
VS.IU.LdBalRt
CS.IMEI
Number of
Times that CS
Load Balancing
is Performed by
IMEI Users
BSC6910
WRFD-021306
Iu Flex Load
Distribution
Management
67192541
VS.IU.Load.Ro
utePS.IMSI
Number of
Performed PS
Load Balancing
by IMSI Users
BSC6910
WRFD-021306
Iu Flex Load
Distribution
Management
67192542
VS.IU.Load.Ro
utePS.NRI
Number of
Performed PS
Load Balancing
by TMSI Users
Due to Invalid
NRI
BSC6910
WRFD-021306
Iu Flex Load
Distribution
Management
67192543
VS.IU.Load.Ro
utePS.IMEI
Number of
Performed PS
Load Balancing
by IMEI Users
BSC6910
WRFD-021306
Iu Flex Load
Distribution
Management
Issue 02 (2013-09-30)
91
WCDMA RAN
Iu Flex Feature Parameter Description
11 Glossary
11
Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
Issue 02 (2013-09-30)
92
WCDMA RAN
Iu Flex Feature Parameter Description
12 Reference Documents
12
Reference Documents
1.
2.
3.
Issue 02 (2013-09-30)
93