Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
S2
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname S2
S2(config)#banner motd #Welcome Authorized Users Unauthorized
access prohibited!#
S2(config)#enable secret class
S2(config)#line vty 0 4
S2(config-line)#password cisco
S2(config-line)#login
S2(config-line)#exit
S2(config)#service password-encryption
S2(config)#ip default-gateway 172.17.99.1
S2(config)#
S3
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname S3
S3(config)#banner motd #Welcome Authorized Users Unauthorized
access prohibited!#
S3(config)#enable secret class
S3(config)#line vty 0 4
S3(config-line)#password cisco
S3(config-line)#login
S3(config-line)#exit
S3(config)#service password-encryption
S3(config)#ip default-gateway 172.17.99.1
S3(config)#
Paso 2. Configurar la interfaz VLAN de administracin en S1, S2 y S3.
Crear y habilitar la interfaz VLAN 99 en cada switch. Utilice la tabla de direccionamiento para la
configuracin de direcciones.
S1
S1(config)#int vlan 99
S1(config-if)#ip address 172.17.99.31 255.255.255.0
S1(config-if)#exit
S1(config)#
S2
S2(config)#int vlan 99
S2(config-if)#ip address 172.17.99.32 255.255.255.0
S2(config-if)#exit
S2(config)#
S3
S3(config)#int vlan 99
S3(config-if)#ip address 172.17.99.33 255.255.255.0
S3(config-if)#exit
S3(config)#
Paso 3. Verificar los resultados.
Su porcentaje de finalizacin debe ser del 13%. Si no, haga clic en Verificar resultados para ver qu
componentes requeridos an no se han completado.
Tarea 2: Configurar VTP
Paso 1. Configurar el modo VTP en los tres switches.
Configure S1 como el servidor. Configure S2 y S3 como clientes.
S1
S1(config)#vtp mode server
Setting device to VTP SERVER mode.
S1(config)#
S2
S2(config)#vtp mode client
Setting device to VTP CLIENT mode.
S2(config)#
S3
S3(config)#vtp mode client
Setting device to VTP CLIENT mode.
S3(config)#
Paso 2. Configurar el nombre de dominio VTP en los tres switches.
Use CCNA como el nombre de dominio VTP.
S1
S1(config)#vtp domain CCNA
Changing VTP domain name from NULL to CCNA
S1(config)#
S2
S2(config)#vtp domain CCNA
Changing VTP domain name from NULL to CCNA
S2(config)#
S3
S3(config)#vtp domain CCNA
Changing VTP domain name from NULL to CCNA
S3(config)#
Paso 3. Configurar la contrasea de dominio VTP en los tres switches.
Su porcentaje de finalizacin debe ser del 44%. Si no, haga clic en Verificar resultados para ver qu
componentes requeridos an no se han completado.
Tarea 4: Configurar las VLAN
Paso 1. Crear las VLAN en S1.
Crear y nombrar las siguientes VLAN en S1 solamente. VTP anuncia las nuevas VLAN a S2 y S3.
VLAN 10 Facultad / Personal
VLAN 20 Estudiantes
VLAN 88 Wireless (Guest)
VLAN 99 Gestin y predeterminado
S1
S1(config)#vlan 10
S1(config-vlan)#name
S1(config-vlan)#exit
S1(config)#vlan 20
S1(config-vlan)#name
S1(config-vlan)#exit
S1(config)#vlan 88
S1(config-vlan)#name
S1(config-vlan)#exit
S1(config)#vlan 99
S1(config-vlan)#name
S1(config-vlan)#exit
S1(config)#
Faculty/Staff
Students
Wireless(Guest)
Management&Default
99 Management&Default active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
S3
S3#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------------------------------------1 default active Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gig1/1, Gig1/2
10 Faculty/Staff active
20 Students active
88 Wireless(Guest) active
99 Management&Default active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
Paso 3. Verificar los resultados.
Su porcentaje de finalizacin debe ser del 54%. Si no, haga clic en Verificar resultados para ver qu
componentes requeridos an no se han completado.
Tarea 5: Asignar VLAN a puertos
Paso 1. Asignar las VLAN para acceder a los puertos en S2 y S3.
Asigne los puertos de acceso de PC a VLAN:
VLAN 10: PC1
VLAN 20: PC2
Asigne los puertos de acceso del router inalmbrico a la VLAN 88.
S2
S2(config)#int fa 0/11
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 10
S2(config-if)#int fa 0/18
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 20
S2(config-if)#int fa 0/7
S2(config-if)#switchport mode access
99 Management&Default active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
Paso 3. Verificar los resultados.
Su porcentaje de finalizacin debe ser del 61%. Si no, haga clic en Verificar resultados para ver qu
componentes requeridos an no se han completado.
Tarea 6: Configurar STP
Paso 1. Asegrese de que S1 sea el puente raz para todas las instancias del rbol de expansin.
Utilice prioridad 4096.
S1
S1(config)#spanning-tree vlan 1,10,20,88,99 priority 4096
Paso 2. Verificar que S1 sea el puente raz.
S1#sh spanning-tree
VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 4097
Address 0040.0B60.D3DB
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 4097 (priority 4096 sys-id-ext 1)
Address 0040.0B60.D3DB
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 20
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------------------------------------Fa0/1 Desg FWD 19 128.1 P2p
Fa0/2 Desg FWD 19 128.2 P2p
Fa0/3 Desg FWD 19 128.3 P2p
Fa0/4 Desg FWD 19 128.4 P2p
Fa0/5 Desg FWD 19 128.5 P2p
VLAN0010
Spanning tree enabled protocol ieee
Root ID Priority 4106
Address 0040.0B60.D3DB
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 4106 (priority 4096 sys-id-ext 10)
Address 0040.0B60.D3DB
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 20
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------------------------------------Fa0/1 Desg FWD 19 128.1 P2p
Fa0/2 Desg FWD 19 128.2 P2p
Fa0/3 Desg FWD 19 128.3 P2p
Fa0/4 Desg FWD 19 128.4 P2p
Fa0/5 Desg FWD 19 128.5 P2p
VLAN0020
Spanning tree enabled protocol ieee
Root ID Priority 4116
Address 0040.0B60.D3DB
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 4116 (priority 4096 sys-id-ext 20)
Address 0040.0B60.D3DB
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 20
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------------------------------------Fa0/1 Desg FWD 19 128.1 P2p
Fa0/2 Desg FWD 19 128.2 P2p
Fa0/3 Desg FWD 19 128.3 P2p
Fa0/4 Desg FWD 19 128.4 P2p
Fa0/5 Desg FWD 19 128.5 P2p
VLAN0088
Spanning tree enabled protocol ieee
Root ID Priority 4184
Address 0040.0B60.D3DB
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 4184 (priority 4096 sys-id-ext 88)
Address 0040.0B60.D3DB
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 20
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------
R1(config)#interface fa0/1.88
R1(config-subif)#encapsulation dot1Q 88
R1(config-subif)#ip address 172.17.88.1 255.255.255.0
R1(config-subif)#exit
R1(config)#interface fa0/1.99
R1(config-subif)#encapsulation dot1Q 99 native
R1(config-subif)#ip address 172.17.99.1 255.255.255.0
R1(config-subif)#exit
Paso 2. Verificar los resultados.
Su porcentaje de finalizacin debe ser del 79%. Si no, haga clic en Verificar resultados para ver qu
componentes requeridos an no se han completado.
Tarea 8: Configurar Conectividad Inalmbrica
Paso 1. Configure el direccionamiento IP para WRS2 y WRS3.
Configurar ajustes de LAN y luego direccionamiento esttico en las interfaces de Internet tanto para
WRS2 y WRS3 utilizando las direcciones de la topologa.
Nota: Un error en Packet Tracer puede evitar que la asignacin de la direccin IP esttica en primer
lugar. Una solucin para este problema es configurar los ajustes de LAN primero bajo para
configuracin de red. Guarde los ajustes. A continuacin, configure la informacin de IP esttica
bajo Internet Tipo de conexin y guardar los ajustes de nuevo.