Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Chapter 3: Maintenance
11 Confirm that all three files as shown in Table 3-17 are saved on the laptop in a distinct folder
that has a name noting the OLED Graphics Version number.
Table 3-17 Items that must be downloaded to Laptop and placed in the appropriate folder.
Item
Purpose
btnpanelHT
OLEDBtn
Installing OLED The OLED Button Panel will probably ship with OLED Graphics installed. If necessary, however,
Graphics from this section describes the installation of the Button Panel Controller Board OLED Graphics and the
Laptop (if Button Panel Module OLED Graphics from a laptop via a USB cable connection.
necessary)
ESD: Observe all appropriate safety and ESD precautions listed in Preventing ESD on page 1-5 i of
Chapter 1.
3 If you are installing the Button Panel onto a game with an Ethernet/USB Cover,
Figure 3-112 (B), reference the Technical Service Bulletin 16-020293-xx: CPU-NXT Enclosure
Ethernet/USB Covers for the steps to access the USB Port.
4 Turn the game ON at the Power Switch in order to power the OLED Button Panel during the
OLED Graphics installation.
5 On the laptop, open the WMS_USBTestCommTool_Vx_xx_setup.exe zip file that was
downloaded earlier.
June 2010
the
installation
file
3-67
(also
called
7 Complete the Installation Wizard sequence by hitting Next each time you are prompted,
Figure 3-113 (A).
8 When the Installation Wizard sequence is completed, locate the file WMS USB Test Comm
Tool on the Desktop folder of the laptop. The icon for this file is shown in Figure 3-114.
Figure 3-114 WMS USB Test Comm Tool icon.
If you are unable to locate the WMS USB Test Comm Tool icon or file in the Desktop folder
of the laptop, then the network settings of the laptop have caused the file to be saved in an
alternate location. Search the hard drive of the laptop for the file name WMS USB Test
Comm Tool to locate the file.
16-026146-00
3-68
Chapter 3: Maintenance
9 Start the WMS USB Test Comm Tool program and select Agree when prompted.
The Main Test Program window displays, Figure 3-115.
Figure 3-115 Main Test Program window.
June 2010
3-69
10 Verify that the Product ID (hex) drop-down menu is set to 000b, Figure 3-115 (A), and select
Connect, Figure 3-115 (B).
Figure 3-116 Verify Product ID (hex) and select Connect.
16-026146-00
3-70
Chapter 3: Maintenance
11 View the Status field in the Main Test Program window and determine the following:
If...
Then...
the laptop is not communicating with the Button Panel and the USB or
Power Cable is likely disconnected or damaged. Complete the following
steps to find and address the error:
1 Check the connections of the 24V Power Cable and USB cable to the
Button Panel PCB.
5
6
7
8
9
Check the entire length of the 24V Power Cable for damage.
Replace the USB cable.
Replace the 24V Power Cable.
Replace the Button Panel, as the Button Panel PCB may be damaged.
Try to connect to the Button Panel with another laptop.
June 2010
3-71
12 Select Firmware Download from the drop-down menu, even if that selection is already
highlighted, Figure 3-117 (A).
The Firmware Download window, Figure 3-118, displays.
Figure 3-118 Firmware Download Window.
16-026146-00
3-72
Chapter 3: Maintenance
14 When prompted, select the file btnpanelHT that was downloaded earlier to the laptop and
saved to an appropriate folder.
The status is displayed in the yellow banner as the existing Button Panel Controller Board
OLED Graphics are erased, Figure 3-119 (A), and the new OLED Graphics are installed. When
the installation is complete, the banner turns green, Figure 3-119 (B).
Figure 3-119 Firmware Download Window.
15 Once the Button Panel Control Board is installed, select Download Button Firmware (ALL
Buttons), Figure 3-119 (C).
June 2010
3-73
16 When prompted, select the file OLEDBtn that was downloaded earlier to the laptop and saved
to an appropriate folder.
The status is displayed in the yellow banner as the existing Button OLED Graphics are erased,
Figure 3-120 (A), and the new OLED Graphics are installed.
Figure 3-120 Firmware Download Window.
17 When the installation is complete, the banner turns green, Figure 3-120 (B), and the OLED
Graphics versions are displayed for the controller and each button position. Verify that the
version is correct for the controller and each button.
18 Close the WMS USB Test Comm Tool program.
19 Turn the game OFF at the Power Switch.
16-026146-00