Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1.1
AVERAGES
Consider a waveform xT such as the one shown that has finite duration:
Mathematically, area is simply the definite integral, so we can equate the two areas:
1
T
xT (t )dt
0
If xT(t) is formed by combining simple shapes, such as rectangles, triangles or trapezia, then it is not
necessary to carry out the integration; it is probably simpler to interpret the integral as the area
under the xT(t) curve
The process of "taking the average" is an operator; it accepts a waveform and produces a constant:
the average value
It can be shown that this operator is linear, ie:
for any two waveforms x(t) and y(t) and any pair of numbers a and b
We also note that the average of a constant is the constant itself, that is,
We can perform an important simplification for the average value of a periodic waveform
In this case, the average over a very long time interval is the same as the average over one period
because the waveform repeats itself; hence we can integrate just over one period from t = 0 to T0:
Hence, we can find the area enclosed by one period of the waveform and divide by the period to
find the average value
1.2
The average value over one period can be seen to be zero because the areas above and below the
horizontal axis having equal magnitude and their signs are positive and negative, respectively
Thus, the net area over one full period is zero
Because sin(t + ) = cos(t + 90), we see that its average is also zero; in fact, the average of
any sinusoid-with any frequency and with any phase-is zero
Another waveform whose average we will encounter is the square of the general sinusoid, one
period of which is shown:
We can now apply the property of linearity and our knowledge of the average of a constant and of a
general sinusoid as follows:
2
2.1
Basic expression
Now we can determine the average power absorbed by a general 2-terminal load for the case of
sinusoidal voltages and currents:
We assume that the load consists of any combination of the circuit elements we have studied thus
far: resistors, inductors, capacitors, dependent sources, and/or independent sources
We assume, however, that each of the independent sources (if there are any) is sinusoidal at the
frequency
We allow the voltage to have, the general phase angle
If the entire circuit in which the load is connected, including the load itself, is stable, then after
some time has passed the current will be a sinusoidal waveform the circuit will be operating in the
AC steady state
Then the current will have some phase angle, which we have shown as + ; thus, is zero when
the phase of the current is exactly the same as that of the voltage
If > 0, we say the current leads the voltage; if < 0, we say the current lags the voltage
We show one complete period of both v(t) and i(t) for the case in which = 90
The crest, or peak, of the current waveform comes after or lags the crest of the voltage
waveform
3
The instantaneous power absorbed by the load in the above set-up is given by:
The average power is the average value of the instantaneous power:
We can apply the trigonometric identity:
wirh
x = t + + and y = t +
The constant cos() is called the power factor; it is usually written P F; the adjective leading or
lagging is added to indicate the sign of
Example 18
Find the power absorbed by the following circuit for values of the voltage source phase angle =
0, 90, and 90.
Solution
We first convert to phasor form:
We now find I
An application of KVL and Ohm's law gives
For = 0, I = 0
For = 90:
For = 90:
For = 0, Im = 0 A, so P = 0 W
For = 90, Im = 3 A and = 90, P = (1/2)VmImcos() = (1/2) 12 V 3 A cos(900) = 0 W
For = 90, Im = 3 A also, and = 0; thus, P = (1/2) 12 V 3 A cos(0) = 18 W.
Notice that for = 90, the average power is zero even though neither the current nor the voltage is
zero
2.2
Now let's look at the power consumed by our three basic 2-terminal elements: the resistor, the
capacitor, and the inductor:
We assume that:
V = Vm
I = Im +
V
V Vm
= m
=
Z ( j )
R
R
Im =
Vm
R
=0
1
V2
P = Vm Im cos = m
2
2R
V
V
V
= m = m 90
Z ( j ) L90 L
Vm
= 90
L
1
P = Vm Im cos = 0
2
Im =
Z ( j ) =
I=
1
1
=
90
jC C
V
= CVm90
Z ( j )
= 90
Im = CVm
1
P = Vm Im cos = 0
2
Unlike the resistor, the ideal inductor and the ideal capacitor do not dissipate any power; they are
sometimes referred to as lossless elements
2.3
We assume that v(t) = Vmcos(t) V and look at the AC steady-state currents indicated and the
power absorbed by each of the elements:
We use phasor techniques to solve for the forced response
Resistor current is IR = (Vm0)/R = Vm/R, so the time-domain steady-state response is:
Notice that the resistor power is always positive the resistor only absorbs power
Also, notice that the period of the power waveform is one-half the period of the voltage (and
current).
The AC steady-state inductor power is:
Because the inductor and capacitor currents are so similar, let's look at the associated powers
together on the same plot:
Power flows from the capacitor to the inductor during one half-period and conversely during the
next
The two maximum values are different, in general, with the difference being supplied by the voltage
source
But let's look at the special case in which the two maxima are equal; in this case, we set (1/2)CVm2
= Vm2/(2L)
If we think of keeping the inductance and the capacitance values fixed and varying the frequency,
this will occur when
At resonance, the peak energy stored by the capacitor is equal and opposite to that stored by the
inductor
The inductor and capacitor swap this energy back and forth, and the voltage source must supply
only the energy absorbed by the resistor
The average value of energy absorbed by both the inductor and by the capacitor is zero
3
RMS VALUES
We now consider how effective AC voltages and currents are in delivering power to loads
Consider a possible experiment:
On the left, we have a general time-varying voltage source v(t) connected to a resistive load
On the right, we show a DC voltage source connected to the same load; the arrow indicates that the
voltage is adjustable
The DC voltage is adjusted so that, for some value which we will call Vrms, the average power
absorbed by the resistor is exactly the same as that absorbed in the left hand figure
We can equate the average power in the resistor in the two circuits:
We call this quantity the root-mean-square value of v(t) because we must first square v(t), then
compute the average (or mean) and then take the square root
Note that the rms value is a constant, whereas v(t) is a time-varying waveform
The rms value is a scalar measure of how effective the waveform is in delivering average power to
a load; hence rms values are often referred to as effective values
We similarly show:
In the special case in which the voltage v(t) is a sinusoid, we can write v(t) = Vmcos(t + )
We can quickly compute v 2 ( t ) = Vm2 2 , so
Similarly,
Squaring the waveform gives exactly the same waveform because 12 = 1 and 02 = 0
Thus, the average of the squared waveform is 1/2
Taking the square root, we obtain Xrms = 1/2
Because (1)2 = 1, the square of this waveform is unity, which has the average value of 1
Taking the square root gives Xrms = 1
The period of this waveform is one-half of the previous one; other than that, the computation is the
same
Thus x 2 ( t ) = 1 2 and Xrms = 1/2
In the expression x{t) = Xmcos(t + ), the value Xm is referred to as the peak value
The rms and peak values of a sinusoid are realted by:
Vrms =
Vm
2
An AC voltage of 230 Vrms will develop the same power in a resistor as a DC voltage of 230 V
applied to the same load
The peak value of the AC voltage in this case is 230 2 = 325.3 V
4
The equation we derived for average power in a load with sinusoidal voltage and current can be rewritten using rms voltage and current values:
9
Thus, we can drop the factor of 1/2 if we use rms voltage and current units
Previously, the sinusoidal voltage v(t) = Vmcos(t + ), for example, has the phasor V = Vm
In some situations, phasors are scaled by the factor of 1/2 and thus write V = Vrms where Vrms =
Vm/2
Hence, power is given by the product of the magnitudes of the voltage and current phasors time the
power factor (no factor of 1/2 is needed)
Ohm's law, V = Z ( j ) I is unaffected by using rms voltage and current since both voltage and
current peak values are divided by 2
Example 19
For the 2-terminal load shown, find the rms values of the terminal voltage, the resistor voltage, the
capacitor voltage, and the terminal current; also compute the power factor and the average power
absorbed by the load:
Solution
The peak voltage of 157 V, when divided by 2, gives an rms value of 110 V
The radian frequency of 337 rad/s corresponds to 377/(2!) = 60 Hz
The phasor equivalent (using rms phasors for the voltages and currents) is as follows:
I=
1100
1100
=
= 2253.1 Arms
3 j4 5 53.1
CONCLUSIONS
In this topic, we have considered the important topic of power in more detail than hitherto. We
began by considering the process of taking the average of a signal. We then determined expressions
for the average power in a load and considered power relationships in a resonant circuit. Finally,
we defined RMS values of voltage and current and used them to derive simpler power relationships.
11