Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
CODE: 00ZAR275//A1E
MODEL
AR-235
AR-275
CONTENTS
Parts marked with are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
CAUTION
This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard and IEC825. This means that this
machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eyes retina, there is the danger of spot
damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts.
2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical
system.
4) The middle frame contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
Warning!
This product is a class A product.
If it is operated in households, offices or similar surroundings, it can produce radio interferences at other
appliances, so that the user has to take adequate countermeasures.
VAROITUS!
LASER KLASSE 1
LUOKAN 1 LASERLAITE
VARNING
OM APPARATEN ANVNDS P ANNAT STT N I
DENNA BRUKSANVISNING SPECIFICERATS, KAN
ANVNDAREN UTSTTAS FR OSYNLIG
LASERSTRLNING, SOM VERSKRIDER GRNSEN
FR LASERKLASS 1.
KLASS 1 LASERAPPARAT
CAUTION
INVISIBLE LASER RADIATION,
WHEN OPEN AND INTERLOCKS DEFEATED. AVOID
EXPOSURE TO BEAM.
VARO !
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEFFNET UND
SICHERHEITSVERRIEGELUNG BERBRCKT. NICHT
DEM STRAHL AUSSETZEN.
VARNING !
ADVARSEL
USYNLIG LASERSTRLNING VED BNING, NR
SIKKERHEDSBRYDERE ER UDE AF
FUNKTION. UNDG UDSAETTELSE FOR
STRLNING.
Laserstrahl
CLASS 1
LASER PRODUCT
LASER KLASSE 1
CONTENTS
[1] NOTE FOR SERVICING
1. Warning for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
5. Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6. PWB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
7. Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
[7] ADJUSTMENTS, SETTING
1. List of adjustment items . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
2. Copier adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
A. Process section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
B. Mechanism section . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
C. Image density (exposure) adjustment . . . . . . . . . . . . . .7-9
[8] SIMULATION
F. Fusing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3. Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5
G. DRIVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
4. Safety and environmental protection standards. . . . . . . . . 3-4
5. Environment conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
[4] CONSUMABLE PARTS
1. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
A. SEC/LAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
B. SECL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
C. Europe affiliates/East Europe/SEEG/SUK/SCA/
SCNZ/SEA/SEES/SEZ/SEIS/SEB/SEN/SEF/SMEF/
Russia/Middle East/Africa/CIS . . . . . . . . . . . . . . . . . . . 4-3
I. PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-13
[11] OTHERS
10) When replacing the lithium battery of the PWB, use a specified one
only.
If a battery of different specification is used, it may be broken,
causing breakdown or malfunction of the machine.
11) When carrying a unit with PWB or electronic parts installed to it, be
sure to put it in an anti-static-electricity bag.
It may cause a breakdown or malfunctions.
Do not insert the power plug with dust on it into a power outlet.
It may cause a fire or an electric shock.
7) Do not put a receptacle with water in it or a metal piece which may
drop inside the machine.
It may cause a fire or an electric shock.
8) With wet or oily hands, do not touch the power plug, do not insert
the telephone line jack, do not operate the machine, or do not perform servicing.
It may cause an electric shock.
OP-UP cassette
OP interface PWB
CN140
CN129
CN103
CN104
Pout Gate
Solenoid
CN131
CN126
CN118
CN28
Pout 2 Ssensor
Fuser-Lamp
THERMISTER
Fuser Unit
OP interface PWB
OP-LO cassette
Sol
Drum Initial
Sensor
Paper Remove
PPD1H(PIN):Paper IN
Sensor
Paper Out
Duplex
Duplex-Motor
Shifter-Motor
Sensor
HP
Shifter
SPF-DupSO
Pout Sensor
SPF-pressure
release SOL
SPF-Motor
CN123
CN115
MAIN-Motor
Copy-Lamp
Heater
Defog
AB
FAX-OP-PWB
OPERATION PANEL
CN132
INCH
Coin
Vender
COPY-OP-PWB
LCD
CN108
CCD-PWB
IMC PWB
Sensor
Mirror HP
Cn130
(AB Area ONLY)
SPF-CON-PWB
Sensor
CN125
(INCH Area ONLY)
L2
CN139
Cover
CN136
L1
CN134
Scanner
CN111
D-Sub 25pin
InterLock
Switch
APC-PWB
LSU-PWB
D-Sub 9pin
MCU-PWB
CN117
D-Sub 15pin
BD-Sensor
BD-PWB
HVU
Power Unit
Power Supply
(CE Only)
Reactor
PS-SW
PS Cooling Fan
(Japan Only)
Defog Heater
(Optional)
PCL PWB
(Optional)
Staple HP sensor
Stapler
FAX PWB
JAM process PG
open/close sensor
Mother PWB
Down-Load-CON
Option interface
PWB
Polygon-Motor
Toner-Motor
(include CRSM)
UNIT
DEV
CN135
CN107
CN112
SPF-PSOL
CN106
SPF PS Sens
CN110
CN121
Mirror-Motor
CN109
SPF-SEN-PWB
CN102
TRAYPAPER
SENSOR
FINISHER PWB
1. Structure
A. Hardware
Block diagram
Model
AR-VR3
AR-RP3
AR-SP4
AR-D11
AR-D12
AR-TR3
AR-FN5
AR-FX4
Platen cover
Reversing single pass feeder
Single pass feeder
500-sheet paper feed unit
2X500-sheet paper feed unit
Job separator tray kit
Finisher
Facsimile expansion kit
Fax memory
2MB
4MB
8MB
AR-MM5
AR-MM6
AR-MM7
AR-P11
Y
Y
Y
Y
Y
Y
Y
Y
AR-NC5J
AR-NS2
AR-PF1
AR-PK1
Y
Y
Y
Y
Y
Y
Y
Y
NOTE
When the printer board is set up on the machine, the function of duplex
can be automatically detected on printer mode.
For details of the options, refer to the Service Manual of each option.
(2) Options
AR-235/275
AR-D12
2X500-sheet paper feed unit
AR-TR3
Job separator tray kit
AR-P11
Printer expansion kit
AR-NC5J
Print server card
Kingston Technology
Product name
DM864VS65804X-7AG
DM864VS65804X-75G
DM1665VS65804X-7AG
DM1665VS65804X-75G
KVR100X64C2/64
KVR133X64C3/128
Capacity
AR-VR3
Platen cover
AR-RP3
Reversing single pass feeder
AR-SP4
Single pass feeder
AR-D11
500-sheet paper feed unit
AR-FN5
Finisher
AR-MM5/MM6/MM7
2/4/8MB Fax memory
AR-NS2
Network scanner expansion kit
AR-PF1
Bar code font kit
AR-PK1
PS3 expansion kit
AR-FX4
Facsimile expansion kit
Maker
Viking Components
64MByte
128MByte
64MByte
128MByte
Product name
VIK4642CL2
VIK8641CL2
VIK6642CL2
Capacity
32MByte
64MByte
128MByte
[3] SPECIFICATIONS
1. Basic specifications
(1) Type
Machine Type
Desktop type
(4) Weight
AR-235/275
About 55.95 kg
42.5 kg
Packaged
Copier body
Magnification
precision
Normal
Document Size
After turned on
Recovery from power-save mode
Recovery from paper jam
Under 40 seconds
Under 10 seconds
10 sec.
B. Copy mode
(1) Document size
A3 paper (11" 17")
Independent
magnification width
A. Common operation
Auto mode
Character mode
Text/Photo mode
Photo mode
Super Photo mode
2. Operation specifications
A3
B4
A4 (Horizontal feed)
A4 (Vertical feed)
B5 (Horizontal feed)
B5 (Vertical feed)
11" 17"
8-1/2" 14"
8-1/2" 13"
8-1/2" 11" (Horizontal
feed)
8-1/2" 11" (Vertical
feed)
A5/INV
AR-235
600 dpi 1200 dpi
12
7.5
14
8.5
23
13.5
16
9
23
13.5
18
10.5
12
7.5
13
8
14
8.5
AR-275
600 dpi 1200 dpi
15
7.5
17
8.5
27
13.5
18
9
27
13.5
21
10.5
15
7.5
16
8
17
8.5
23
13.5
27
13.5
16
18
23
13.5
27
13.5
AR-235
600 dpi 1200 dpi
12
7.5
14
8.5
23
13.5
16
9
23
13.5
18
10.5
12
7.5
13
8
14
8.5
AR-275
600 dpi 1200 dpi
15
7.5
17
8.5
27
13.5
18
9
27
13.5
21
10.5
15
7.5
16
8
17
8.5
23
13.5
27
13.5
16
18
23
13.5
27
13.5
AR-235/275 SPECIFICATIONS - 1
3. Engine specifications
AR-235
600 dpi 1200 dpi
12
7.5
14
8.5
23
13.5
16
9
23
13.5
18
10.5
12
7.5
13
8
14
8.5
AR-275
600 dpi 1200 dpi
15
7.5
17
8.5
27
13.5
18
9
27
13.5
21
10.5
15
7.5
16
8
17
8.5
23
13.5
27
13.5
16
18
23
13.5
27
13.5
Paper kind
Special paper
Paper size
selection
Slide switch
Cassette
attachment/
detachment
Remarks
c. Zoom method
Main scanning
direction
Sub scanning direction
Capacity
Paper weight
Document Size
Paper kind
Read
Main scanning direction
Basic
Virtual
resolution
resolution
400 dpi
Write
Main scanning direction
Basic
Virtual
resolution
resolution
600 dpi
1200 dpi
Center
3.2 line/mm
3.6 line/mm
5.0 line/mm
5.0 line/mm
5.0 line/mm
AB Series: A3 to A6R
Inch Series: 11"17" to 8.5"5.5"
Cassette section: empty detection only available
Manual paper feed section: empty detection only
available
Corners
2.8 line/mm
3.2 line/mm
4.5 line/mm
4.5 line/mm
4.5 line/mm
Yes
Size detection
Guide display
When poor image quality is resulted by the use of OHP sheet, adjust
e. Gradation
Read
Write
5002+100
d. Resolution
Copy magnification
ratio
25% to 49%
50% to 69%
70% to 94%
95% to 105%
106% to 141%
142% to 400%
Single-side copy
256 gradations
2 gradations
c. Simultaneous wrapping
Setting manual book
d. Function
This exit tray is set up above main exit tray, and can separate copier
exit, printer exit and FAX exit.
AR-235/275 SPECIFICATIONS - 2
e. Many of tray
1 (this tray can not set up more than 2)
f. Separator system
b. Scanning area
CENTER
AB system
Inch system
AB system
Inch system
A3 to A6
11 x 17 to 8.5 x 5.5
A3 to A6
11 x 17 to 8.5 x 5.5
i. Paper pass
center (same as main unit)
j. Exit area/finishing
Upper exit tray (Job separator tray)
Lower exit tray (main machine exit tray)
Face down
Face down
k. Power supply
Power supply
Power consumption
l. Method of movement
with original motor (not with main machine)
m. Machine weight
0.6 kg
n. Exit capacity
Upper exit tray (Job separator)
Lower exit tray (main machine exit tray)
100 sheets
500 sheets (550 sheets)
Yes
No
Xenon
1.5 kV
p. Concept of function
Upper exit tray (Job separator)
Type
Drive voltage
Type
(1) Resolution
FAX/Printer (This setting can be
done by users.)
Copy/Printer/FAX (This setting can
be done by users.)
(2) Gradation
2 gradations
q. Reliance
MCBJ
MCBF
216 mm
60k
10k
r.p.m.
Mirror surfaces
Laser power
Laser beam size
Laser wave length
Imaging speed
(1) Type
Photo
conductor
Flat-bed type/monochrome
Toner
Type
LIFE
Type
LIFE
(3) Resolution
Main scanning direction
Basic
Virtual
resolution
resolution
400 dpi
(4) Gradation
28,800 rpm
6 faces
0.4mW/600dpi, 0.2mW/1200dpi
60 (Main scan) x 70 (Sub scan)
785nm
Charge
Transfer
Exposure
Developing
AR-235/275 SPECIFICATIONS - 3
System
Voltage
System
Voltage
Blade
5. Environment conditions
F. Fusing
Type
Voltage
Power
consumption
Fusing temperature
Heat roller
Pressure roller
Separation system
Heat roller
Halogen lamp
100V
1000W
G. DRIVE
Drive section
Main motor
Motor
DC brushless motor
Humidity (%)
Type
Lamp
Temperature (C)
EnergyStar
Standard name
S mark
VCCI class A
VCCI class B
Country name
Japan
Japan
Taiwan
World-wide
Humidity (%)
Item
Safety
standards
Radio wave
noise standard
Temperature (C)
Humidity (%)
Operating
On standby
Temperature (C)
AR-235/275 SPECIFICATIONS - 4
20 to 25C
655%RH
10
10
10
Life
25K (10)
50K (10)
Model name
Remarks
AR-270MT Life setting by A4 (8.5"11") 6% document
MT=NT*10
AR-270MD MD=ND*10
1
1
1
2
4
50K
150K
AR-270DR
AR-270UH
1
4
300K
AR-270LH
100K
AR-270KA1
2
2
1
10
10
1
50K (10)
50K (10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
3 3000 staples
3
1
100K
1
100K
1
150K
AR-SC1
AR-270TX
AR-270IR
AR-270FU
* The other maintenance parts than the above are supplied as service parts.
B. SECL
No.
Item
Content
1 Toner CA (black) w/IC Toner
Vinyl bag
2 Developer
Developer
(Developer; Net weight
500g)
3 Drum kit
Drum
4 Upper heat roller kit
Upper Heat Roller
Fusing gear
Upper heat roller bearing
Fusing separation pawl
(upper)
5 Lower heat roller kit
Lower Heat Roller
Fusing separation pawl
(lower)
Fusing busing (lower)
6 100K PM kit
Drum Separation Unit
Transfer roller unit
DV blade
Side seal F
Side seal R
7 MC unit
MC unit
8 Cleaner Blade
Cleaner Blade
9 Drum frame unit
Drum frame unit
10
10
10
Life
25K (10)
50K (10)
Model name
Remarks
AR-270MT Life setting by A4 (8.5"11") 6% document
MT=NT*10
AR-270MD MD=ND*10
1
1
1
2
4
50K
150K
AR-270DR
AR-270UH
1
4
300K
AR-270LH
100K
AR-270KA
2
2
1
1
1
1
10
10
1
50K (10)
50K (10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
* The other maintenance parts than the above are supplied as service parts.
10
10
10
Life
25K (10)
50K (10)
Model name
Remarks
AR-270LT Life setting by A4 (8.5"11") 6% document
LT=T*10
AR-270LD LD=DV*10
1
1
1
2
4
50K
150K
AR-270DM
AR-270UH
1
4
300K
AR-270LH
100K
AR-270KA
2
2
1
1
1
1
10
10
1
50K (10)
50K (10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
3 3000 staples
3
1
100K
1
100K
1
150K
AR-SC1
AR-270TX
AR-270IR
AR-270FU
* The other maintenance parts than the above are supplied as service parts.
D. Special country/Taiwan
No.
Item
Content
1 Toner CA (black) w/IC Toner
Vinyl bag
2 Developer
Developer
(Developer; Net weight
500g)
3 Drum kit
Drum
4 Upper heat roller kit
Upper Heat Roller
Fusing gear
Upper heat roller bearing
Fusing separation pawl
(upper)
5 Lower heat roller kit
Lower Heat Roller
Fusing separation pawl
(lower)
Fusing busing (lower)
6 100K PM kit
Drum Separation Unit
Transfer roller unit
DV blade
Side seal F
Side seal R
7 MC unit
MC unit
8 Cleaner Blade
Cleaner Blade
9 Drum frame unit
Drum frame unit
10
10
10
Life
25K (10)
50K (10)
Model name
Remarks
AR-270CT Life setting by A4 (8.5"11") 6% document
CT=ST*10
AR-270CD CD=SD*10
1
1
1
2
4
50K
150K
AR-270DR
AR-270UH
1
4
300K
AR-270LH
100K
AR-270KA
2
2
1
1
1
1
10
10
1
50K (10)
50K (10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
3 3000 staples
3
1
100K
1
100K
1
150K
AR-SC1
AR-270TX
AR-270IR
AR-270FU
* The other maintenance parts than the above are supplied as service parts.
10
10
10
Life
25K (10)
50K (10)
Model name
Remarks
AR-270CT Life setting by A4 (8.5"11") 6% document
CT=ST*10
AR-270CD CD=SD*10
1
1
1
2
4
50K
150K
AR-270DR
AR-270UH
1
4
300K
AR-270LH
100K
AR-270KA
2
2
1
1
1
1
10
10
1
50K (10)
50K (10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
3 3000 staples
3
AR-SC1
* The other maintenance parts than the above are supplied as service parts.
3. Environment conditions
<TD cartridge>
Serial number
(0001-9999)
Destination
Unit version
Production
month
1
January
September
October
November
December
9
0
X
Y
Humidity (%)
Temperature (C)
Humidity (%)
Label position
<Drum>
The laser print indicates the date (year, month, day) of production.
Temperature (C)
Humidity (%)
Use environment
conditions
Temperature (C)
If power is turned don without removing the fixing pin, it will be diffi-
TD cartridge lock
release lever
2) Hold the paper pressure plate and turn the fixing pin in the arrow
direction.
3) Remove the developer tank from the developer cartridge.
3) Store the removed fixing pin and the fixing screw which was
removed in the above procedure, together in the specified storage
place in the tray.
Hook
Fixing pin
Shake the developer bag enough before opening it.
Check to insure that the hook is engaged in two positions.
Screen display
3) On the screen, all trays are indicated and the previously selected
tray is highlighted. Use the Up/Down key to select the tray desired.
Shutter
Screen display
Tape
Knob
Do not hold the shutter lever when shaking.
2) Press the lock release lever, and insert the unit completely into the
copier along the guide groove. Then fix the blue screw and the
locking screw.
installing.
4) After selecting the tray, press the Right cursor key to move to the
paper size selection box on the right side of the screen (the highlighted size is the previously selected size). Use the Up/Down key
to select the desired paper size.
5) After selecting the paper size, press the Left cursor key to return to
the left side of the screen. At that time, the selected tray indicates
the paper size selected above.
3) Take off the tape, and remove the shutter from the toner cartridge.
6) After the Start key is pressed, if the fed paper is different in size
from the setting, the machine makes copy and then stops running
with the mode retained. The following message appears for six
seconds. the Start LED is ON): The tray set EXTRA size is not
available for this specification.
Message (C449)
2) To select the paper size from the operation panel, press the Special Function key and choose "Paper Size Enter" from the function
menu to open the paper size enter screen.
2
3
4
5
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Name
Platen cover (optional)
Paper output tray
Front cover
Paper trays
Power switch
Handles
Operation panel
Original table
Upper exit area cover
Side cover
Side cover handle
Bypass tray guides
Bypass tray
Bypass tray extension
Function/Operation
Place the original on the original table and close the platen cover before copying starts.
Finished copies are deposited in the paper output tray.
Open to remove misfeeds and for copier servicing.
Each tray holds 500 sheets of copy paper.
Press to turn copier power on and off.
Use to move the copier.
All copier controls are located here for easy operation.
Place the document to be copied here.
Open to remove misfeeds when an optional job separator tray kit or finisher is installed.
Open to remove misfeeds.
Lift and pull to open the side cover.
Adjust to the width of the copy paper.
Special papers (including transparency film) and copy paper can be fed from the bypass tray.
Pull out when feeding large paper such as 8-1/2" x 14" and 11" x 17".
2. Internal
2
3
4
5
No.
1
2
3
4
5
Name
Toner cartridge lock release lever
Toner cartridge
Paper guide
Fusing unit release levers
Roller rotating knob
Function/Operation
Use to unlock the toner cartridge.
Contains toner.
Open to remove misfed paper.
Lower to remove misfed paper.
Turn to remove misfed paper.
3. Operation panel
A. Key position
(U.S.A., Canada)
1
12
13 14
15
16
17
18
5 6
19 20
21
22
10
11
23
No.
1
Name
COPY key and indicator
Function/Operation
Press to select the COPY mode.
Press and hold during standby to display the total output count. Quantity of toner remaining is also displayed.
Displays information to assist the operator.
Press to return the display to the previous screen.
Press to display the detailed description when [i] is displayed at the upper right of the display.
Press to check the settings of selected functions or the status of reserved output jobs.
Press to register the selected setting.
Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are
made.
Used to select the desired copy quantity.
Interrupts a copy run.
2
3
4
5
6
7
Display
BACK key
Information key
JOB STATUS key
OK key
Copy quantity display
8
9
10
11
Numeric keys
INTERRUPT key and
indicator
CLEAR ALL key
START key and indicator
12
13
14
15
16
EXPOSURE key
PAPER SELECT key
COPY RATIO key
AUTO IMAGE key
2-SIDED COPY key
17
OUTPUT key
18
19
20
21
22
PROGRAM/READ END
key
CLEAR key
23
Clears all selected settings and returns the copier to the initial settings.
Copying is possible when the indicator is on.
Press to start copying.
Used to select the exposure modes: AUTO, TEXT, TEXT/PHOTO, PHOTO or SUPER PHOTO.
Used to manually select a paper tray.
Press to select a reduction or enlargement copy ratio.
Press for automatic copy ratio selection.
Press to select the 1-sided to 1-sided, 1-sided to 2-sided, 2-sided to 1-sided* or 2-sided to 2-sided* copy mode.
*To select the 2-sided to 1-sided or 2-sided to 2-sided copy mode, an optional RSPF must be installed.
Press to select the sort, group or staple sort* mode.
*To select the staple sort mode, an optional finisher must be installed.
Press to select special functions.
Press to move the highlighted item in the display.
Press to close an open account.
Use as part of numeric keys to enter copy quantity.
Press during a continuous copy run to display the number of copies completed in the current run.
Press to select the job memory mode.
Press to finish scanning of originals and to start copying when copying from the original table.
Press to clear the copy quantity display or press during a copy run to terminate copying.
B. LCD panel
(U.S.A., Canada)
1
No.
1
2
Name
Exposure display
Message display
3
4
Function/Operation
Indicates the selected exposure mode.
Messages are displayed regarding
copier status and operation.
The original paper size is displayed.
Displays the copy ratios for reductions
or enlargements.
Displays the selected paper size.
When "AUTO" is displayed, paper size
matching the original and copy ratio
will be automatically selected.
The selected paper feed location is
highlighted.
5. Sensor
2
3
1
1
18
2
29
17
28
27
5
6
7
26
10
11
12
13
14
8
9
25
10
14
13
12
17
24
16
11
30
23
18
22
21
15
No.
1
2
3
4
Name
Mirror motor
Shifter motor
Paper exit gate
switching solenoid
Duplex motor
Cooling fan
6
7
8
Main motor
PS clutch
Manual paper feed
solenoid
Manual paper feed
clutch
Paper feed transfer
clutch
Paper feed clutch
Cassette lift-up motor
Paper feed solenoid
9
10
11
12
13
14
17
18
15
16
20
Code
MIRM
SFTM
PGSOL
DPXM
TFAN
MM
PSRSOL
HPSOL
PCL1H
LUM1H
PCS1H
TM
PREMS
OL
PSFAN
Toner supply
Separation pawl
operation solenoid
Cools the inside of the
unit.
15
16
No
.
1
Name
19
Code
DSIN0
MHPS
3
4
Document cover
sensor
Document size sensor
POUT
SFTHP
Thermostat
10
HPIN
11
CSS1
12
13
14
15
16
17
18
OCCOVER
DSIN3
PDPX
RTHIN
HPEMPTY
HPWS
HPTRAY2
HPTRAY1
HPSIZE2
HPSIZE1
Function and
operation
Document size
detection
Mirror (scanner)
home position
detection
Document cover
open/close detection
Document size
detection
1st paper exit
detection
Shifter home position
sensor detection
Paper exit detection
Fusing temperature
detection
Abnormal high
temperature detection
in the fusing section
Sensor of paper entry
from the manual
paper feed tray, the
2nd/multi-stage desk,
or the DUP
1st cassette (paper
tray) empty detection
Manual feed paper
empty detection
2nd cassette (paper
tray) empty detection
Manual feed paper
width detection
Manual feed tray
position detection
Manual feed tray
position detection
Manual feed paper
length detection
Manual feed paper
length detection
No
.
19
Name
Code
Door switch
SW24V
20
21
22
23
24
25
26
27
28
29
LUD1H
PAP1H
TRAYPAPER
POUTCOV
30
POUT2
PFULL2
Function and
operation
Front door and side
door open/close
detection
Side door open/close
detection
2nd cassette paper
pass
2nd cassette paper
upper limit detection
7. Section
1 2
6
23
8
9
10
11
12
13
14
16
17
18
19
22
No.
1
2
Name
Copy lamp
Copy lamp unit
LSU unit
Lens unit
MC holder unit
6
7
8
10
11
12
13
Drum unit
DUP transport follower
roller
DUP transport roller
Transport roller
14
Resist roller
15
16
17
1
2
3
11
6
10
18
No.
1
2
3
4
5
6
Name
Inverter PWB
CCD PWB
Option connector PWB
IMC PWB
MCU PWB
Mother board
7
8
9
10
11
6. PWB unit
19
20
Image process
Main unit control
Connection with FAX PWB and
PCL PWB
2nd tray control
For the copy operation
LCD control
For the FAX operation
AC power input/DC voltage
control
21
22
23
15
21 20
Section
Process section
Mechanism section
Adjustment item
Developing doctor gap adjustment
MG roller main pole position adjustment
Developing bias voltage adjustment
Grid bias voltage adjustment (High mode)
Grid bias voltage adjustment (Low mode)
OC image lead edge position/Sub scanning
magnification ratio/Original offset auto adjustment
Print start position adjustment
SPF image lead edge position adjustment
Rear edge void adjustment
Paper off center adjustment
Left edge void area adjustment
Main scanning direction (FR direction) distortion
balance adjustment
(1)
(2)
(3)
(4)
(5)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
Image density
(exposure) adjustment
(1)
2. Copier adjustment
SIM46-2
<Adjustment specification>
Developing doctor gap
A. Process section
+0.1mm
+0.15mm
1.55-0.2mm
150mm
20mm
3) Hold the string and bring the needle close to the MG roller horizontally. (Do not use paper clip, which is too heavy to make a correct
adjustment.) (Put the developing unit horizontally for this adjustment.)
10mm
10mm
R
20mm
DG:1.5 -+0.1
0.15
C
4) Do not bring the needle into contact with the MG roller, but bring it
to a position 2 or 3mm apart from the MG roller. Mark the point on
the MG roller which is on the extension line from the needle tip.
5) Measure the distance from the marking position to the top of the
doctor plate of the developing unit to insure that it is 18mm.
If the distance is not within the specified range, loosen the fixing
screw A of the main pole adjustment plate, and move the adjustment plate in the arrow direction to adjust.
DG:1.55 -+0.15
0.2
F
DG:1.5 -+0.1
0.15
3) Tighten the developing doctor fixing screw.
4) Check the clearance of the developing doctor. If it is within the
specified range, then fix the doctor fixing screw with screw lock.
When inserting a thickness gauge, be careful not to scratch the
AR-235/275 ADJUSTMENTS - 1
2) After selecting the mode, enter the adjustment value and press the
[OK] key.
3) Output will be made for 30 sec.
<Adjustment specification>
Display items
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
AE
Character
Character/Photo
Photo
Super photo
Toner save
Setting
range
1-8
Default
4 (426)
5 (450)
5 (450)
5 (450)
3 (400)
2 (375)
B. Mechanism section
Content
COPY
426
450
450
2) After selecting the mode, enter the adjustment value and press the
[OK] key.
3) Output will be made for 30 sec.
Set the
test chart
<Adjustment specification>
Display items
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
Content
AE
Character
Character/Photo
Photo
Super photo
Toner save
Installation
range
200-550
Default
426 (426V)
450 (450V)
450 (450V)
450 (450V)
400 (400V)
376 (376V)
2) After selecting the mode, enter the adjustment value and press the
[OK] key.
3) Output will be made for 30 sec.
<Adjustment specification>
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
Display items
3) Make a copy.
Content
AE
Character
Character/Photo
Photo
Super photo
Toner save
Setting
range
1-8
Default
4 (555V)
5 (580V)
5 (580V)
5 (580V)
3 (530V)
2 (505V)
(Input screen)
(Executing screen)
Display
items
1:TRAY1
2:OPTION
3:MANUAL
4:DUPLEX
Content
1st cassette
Option cassette
Manual feed
Back print
Setting
range
0-99
1-99
Default
53
AR-235/275 ADJUSTMENTS - 2
<Adjustment specification>
Adjustment
mode
SPF image
lead edge
position
SIM
Set value
Spec value
50-6
1 step:
0.127mm
shift
Setting
range
1 99
10
A4 (8.5" x 11")
Fit the print edge with the paper edge, and perform the lead
edge adjustment.
Example:99 5/0.127 = 99 39.4 = about 59
FIf the set value is not obtained from the above formula, perform the fine adjustment.
3) Execute SIM 50-1-2 to adjust the main cassette lead edge void.
1 step of the set value corresponds to about 0.127mm shift.
Calculate the set value from the formula below.
B/0.127 (mm) = Lead edge void adjustment value <B: Lead edge
void (mm)>
2.5mm
5
10
Scale image
SIM
50-12
50-5
Set value
B/0.127
99 H/0.127
Spec value
Lead edge void:
1 to 4mm
Image loss: 3mm
or less
Setting
range
1 99
4) Execute SIM 50-1 and set the density mode to DEN-B. The currently set adjustment value is displayed.
5) Enter the set value and press the start key.
The correction value is stored and a copy is made.
<Adjustment specification>
Adjustment
mode
Rear edge
void
SIM
Set value
1 step: 0.127mm
shift
50-1-6
Spec
value
4mm or
less
Setting
range
1 99
Since the printed copy is used as a test chart, put the scale in
paralleled with the edge lines.
AR-235/275 ADJUSTMENTS - 3
(Input screen)
(Executing screen)
Display
Setting
Content
Default
items
range
1:BYPASS Manual feed
1-99
50
2:TRAY1
1st cassette
3:TRAY2
2nd cassette
4:TRAY3
3rd cassette
5:TRAY4
4th cassette
6:DUPLEX Back print
Setup of various copy conditions: Similar to the normal copy mode.
<Adjustment specification>
Adjustment
mode
Left edge void
Second
print surface
off-center
SIM
50-10
-2
50-10
-6
Set value
Add 1: 0.127mm
shift to R side.
Reduce 1:
0.127mm shift to L
side.
Spec value
Single:
Center
2.0mm
Duplex:
Center
2.5mm
50-18
Set value
1 step: 0.127mm
shift
1)
Setting
range
1 99
1)
1)
2)
3)
1)
4)
5)
copy.
3) Execute SIM 50-1.
Select the mode with the arrow keys, enter the adjustment value
with the 10-key, and press the [OK] key.
Pressing the [START] key makes a print.
Pressing the [RETURN] key returns to the mode selection.
(Input screen)
(Executing screen)
Display items
Content
Setting
range
1 99
(Initial screen)
Spec
value
0.5 4mm
<Adjustment specification>
Adjustment
mode
Paper off
center
SIM
Setting
range
1-99
Default
43
1-99
18
1-99
18
1-99
18
1-99
18
1-99
1-99
30
50
1-99
18
1-99
18
1-5
AR-235/275 ADJUSTMENTS - 4
3) Manually turn the mirror base drive pulley and bring No. 2/3 mirror
base unit into contact with the positioning plate.
At that time, if the front frame side and the rear frame side of No. 2/
3 mirror base unit are brought into contact with the positioning
plate at the same time, the mirror base unit parallelism is proper.
6) Put No. 2/3 mirror base unit on the positioning plate again, push
the projections on the front frame side and the rear frame side of
the copy lamp unit to the corner frame, and tighten the wire fixing
screw.
4) Loosen the set screw of the scanner drive pulley which is not in
contact with No. 2/3 mirror base unit positioning plate.
5) Without moving the scanner drive pulley shaft, manually turn the
scanner drive pulley until the positioning plate is brought into contact with No. 2/3 mirror base unit, then fix the scanner drive pulley.
La
Paper exit
direction
Original
Copy
AR-235/275 ADJUSTMENTS - 5
3) Measure the width of the black background at the lead edge and at
the rear edge.
Original
Copy A
Copy B
Parallel line
Parallel line
10mm
10mm
10mm
10mm
White paper
2) Make a normal (100%) copy of the test sheet on A3 (11" x 17")
paper. (Fit the paper edge and the glass holding plate edge.)
3) Measure the distances (La, Lb, Lc, Ld) at the four corners as
shown below.
La
Lc
Rear side
A
Paper exit
direction
Front side
Lb
Ld
4) Move the mirror base B rail position up and down (in the arrow
direction) to adjust.
<Adjustment specification>
La = Lb
6) Execute the main scanning direction (FR) distortion balance
adjustment previously described in 2) again.
AR-235/275 ADJUSTMENTS - 6
When La > Lb
Shift the mirror base B rail upward by the half of the difference of
LaLb.
When La < Lb
Shift the mirror base B rail downward by the half of the difference
of LbLa.
Example: When La = 12mm and Lb = 9mm, shift the mirror base
B rail upward by 1.5mm.
When .E >.F
Shift the mirror base B rail downward by the half of the difference
of LcLd.
When Lc < Ld
When Lc < Ld, move the mirror base B on the paper feed side
upward.
When moving the mirror base rail, hold the mirror base rail with
Display
Content
The correction
value
calculated is
over 5%.
Paper jam
lamp ON
Reference line
scanning error
Major cause
Improper position of reference
width line of the reference white
plate
Improper installation of CCD unit
Defective CCD
No reference white plate
your hand.
<Adjustment specification>
La = Lb, Lc = Ld
5) After completion of adjustment, manually turn the mirror base drive
pulley, scan the mirror base A and mirror base B fully, and check
that the mirror bases are not in contact with each other.
If the mirror base rail is moved extremely, the mirror base may be in
contact with the frame or the original glass. Be careful to avoid this.
Spec value
SIM
Set value
At normal:
1.0%
48-13
Add 1:
0.05% increase
Reduce 1:
0.05% decrease
Setting
range
1 99
Since the printed copy is used as a test chart, put the scale in
paralled with the edge lines.
<Adjustment specification>
2) Set the test chart on the SPF and make a normal (100%) copy.
Adjustment
mode
Main scanning
direction
magnification
ratio
Spec value
At normal:
1.0%
SIM
48-1
Set value
Add 1: 0.1%
increase
Reduce 1: 0.1%
decrease
Setting
range
1 99
AR-235/275 ADJUSTMENTS - 7
<Adjustment specification>
Distance <
: Shift toward A.
Distance >
: Shift toward B.
<Adjustment specification>
Adjustment
mode
Sub scanning
direction
magnification
ratio (SPF mode)
Spec value
SIM
Set value
At normal:
1.0%
48-1-4
48-1-5
Add 1:
0.05% increase
Reduce 1:
0.05% decrease
Setting
range
1 99
2) Make a normal copy from the manual paper feed tray, and check
the printed copy with the test chart.
If any adjustment is required, perform the following procedure.
3) Execute SIM 50-12.
3) Keep A=125mm, and execute SIM 41-4. (Do not put paper on the
table.)
4) Check the reaction with SIM 41-1.
<Adjustment specification>
Adjustment
mode
Original off
center mode
(SPF mode)
Spec value
SIM
Set value
Single: Center
3.0mm
Duplex: Center
3.5mm
50-12
Add 1: 0.1mm
shift to R side
Reduce 1: 0.1mm
shift to L side
Setting
range
1 99
3) Slide the lens unit toward the rear side and attach it, then execute SIM.
AR-235/275 ADJUSTMENTS - 8
When the lens unit is moved, execute the OC main scanning magni-
fication ratio auto adjustment, SIM 48-1-1, SIM48-3 and the SPF
original off-center adjustment.
This adjustment is basically O.K. with SIM 63-7.
Front
Display
Lamp
AUTO
TEXT
TEXT
TEXT/
PHOTO
PHOTO
TEXT/
PHOTO
PHOTO
SUPER
PHOTO
TONER
SAVE
SUPER
PHOTO
AUTO (TS)
TEXT (TS)
TEXT
PHOTO (TS)
Exposure
level
3
3
3
3
3
3
3
Sharp Gray
Chart output
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
Set value
If too bright,
increase the
quantity
displayed on
the copy
quantity
display.
If too dark,
decrease the
quantity
displayed on
the copy
quantity
display.
Setting
range
0 99
AR-235/275 ADJUSTMENTS - 9
[8] SIMULATION
1. Operating procedures and operations
Screen
Maginification
ratio selection
A. Basic operation
Procedure
Key operation
Execution
Key
CA
Interrupt
,
,
OK
Back
CA
Interrupt
Back
Function
Cancel simulation
Sub code input screen appears.
Magnification ratio selection (1% increment)
Fixed magnification ratio setting
Shifts to the screen during operation.
Shifts to the number of times selection screen.
Cancel simulation
Sub code input screen appears.
Shifts to the magnification ratio setup menu.
# INTERRUPT C INTERRUPT
Screen
Key
Selection of
CA
the adjustment Interrupt
items
C
10-key
,
OK
Adjustment
CA
value input
Interrupt
10-key
C
OK
Back
Execution
CA
Interrupt
Back
10-key and
OK or START
INTERRUPT
CA
Selection of the main code and the sub code is set with the [START]
key.
There are two or more screens, the adjustment "Current page/Max.
page" is displayed. Press [] key (previous page) or [] key to select
a screen.
Screen
Key
Selection of the CA
adjustment
Interrupt
items
C
10-key
,
,
OK
START
Screen
Key
Counter display CA
Interrupt
,
Function
Cancel simulation
Sub code input screen appears.
Page switch (in the case of multiple pages)
Key
CA
Interrupt
,
Function
Cancel simulation
Sub code input screen appears.
Page switch (in the case of multiple pages)
Adjustment
value input
CA
C
Back
10-key
START
Execution
CA
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Adjustment item selection
Page switch (in the case of multiple pages)
The adjustment value input screen appears.
Cancel simulation
The sub code input screen appears.
Adjustment value input
Input value clear
Input final value
The adjustment item select screen appears.
Execution
Key
CA
Interrupt
C
10-key
,
OK
CA
Interrupt
Back
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Load number selection
Page switch (in the case of multiple pages)
Shifts to the screen during operation.
Cancel simulation
Sub code input screen appears.
The load selection screen appears.
Screen
Initial stage
Execution
Key
CA
Interrupt
Selection of the
C
number of times
10-key
OK
Function
Simulation cancel
Sub code input screen appears.
Input value clear
Entry of the number of times
Shifts to the magnification ration selection screen.
Key
CA
Interrupt
C
10-key
OK
CA
Interrupt
Back
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Speed number selection
Shifts to the screen during operation.
Cancel simulation
Sub code input screen appears.
The intial screen appears.
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Adjustment value input
Page switch (in the case of multiple pages)
Item switch
The adjustment value input screen appears.
Input value assured. Print one page. Shifts to
the execution screen.
Cancel simulation
Input value clear
The adjustment item selection screen appears.
Adjustment value input
Determination of the input value Print of one page
shift to the execution screen.
After the single print, the copy conditions are cleared
and the adjustment value input screen appears.
After the single print, the copy conditions are not
cleared and the adjustment value input screen
appears.
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Adjustment item selection
Page switch (in the case of multiple pages)
The adjustment value input screen appears.
Cancel simulation
Sub code input screen appears.
Adjustment value input
Input value clear
Set value check
The adjustment item selection screen appears.
Cancel simulation
Sub code input screen appears.
The adjustment value input screen appears.
Check
Key
CA
Interrupt
C
10-key
OK
CA
Interrupt
OK
Back
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Load number selection
The check screen appears.
Cancel simulation
Sub code input screen appears.
Clears and shifts to the counter select menu.
Not clears and shifts to the counter select menu.
AR-235/275 SIMULATION - 1
Key
Function
CA
Cancel simulation
Interrupt Sub code input screen appears.
Screen type
Adjustment value
input menu
Adjustment value
input menu
Adjustment value
input menu
Execution menu
Execution menu
Adjustment value
input menu
6
Used to clear.
Initial menu
Confirmation menu
Selection menu
Initial menu
Execution menu
Selection menu
10
Confirmation menu
Execution menu
Execution menu
AR-235/275 SIMULATION - 2
No.
11
Screen type
Input menu of the
number of times
Magnification ratio
and original size
setup menu
Execution menu
12
Execution menu
Input menu
1
2
3
2
3
6
7
11
2
3
1
2
3
2
7
1
6
8
Code
Main
Sub
8
1
Function
Used to check the operation of the scanner unit
and its control circuit.
Used to check the operation of sensor and
detector in the scanning (read) section and the
related circuit.
Used to check the operation of the SPF unit and
the related circuit.
Used to check the operation of sensors and
detectors in the SPF unit and the related circuit.
Used to check the operation of the loads in the
SPF unit and the control circuits.
Used to check the operation of sensor and
detector in the finisher and the related circuit.
Used to check the operation of the load in the
finisher and the control circuit.
Used to adjust the finisher jogger position.
Used to adjust the offset tray operations.
Used to check the operation of the shifter.
Used to check the operation of sensor and
detector in the option tray and the related circuit.
Used to check the operation of the load in the
option tray and the control circuit.
Used to check the operation of the display, LCD in
the operation panel, and control circuit.
Used to check the operation of the heater lamp
and the control circuit.
Used to check the operation of the copy lamp and
the control circuit.
Used to check the oepration of the loads (clutches
and solenoids) in the paper transport system and
the control circuit.
Used to check the operation of each fan motor and
its control circuit.
Used to set the aging operation conditions.
Used to set the cycle of intermittent aging.
Used to set the display of the warm-up time.
10
11
12
13
14
15
4
5
10
14
16
17
21
0
0
1
AR-235/275 SIMULATION - 3
Function
Used to check and adjust the operation of the
developing bias voltage in each copy mode and
the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each copy
mode and the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each copy
mode and the control circuit.
Used to check and adjust the operation of the
developing bias voltage in each printer mode and
the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each printer
mode and the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each printer
mode and the control circuit.
Used to check and adjust the operation of the
developing bias voltage in FAX mode and the
control circuit.
Used to check and adjust the operation of the main
charger grid voltage (high mode) in FAX mode and
the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (low mode) in FAX mode and
the control circuit.
Used to check and adjust the operation of the load
(motor) in the duplex section and the control
circuit.
Used to adjust the rotation speed of the duplex
motor.
Used to adjust the switch back time of the duplex
motor.
Used to check the operation of the toner motor and
its control circuit.
Used to cancel excluding the self-diag U2/PF
troubles.
Used to cancel the self-diag U2 trouble.
Used to cancel the self diag "PF" trouble.
Used to set the maintenance cycle.
Code
Main
Sub
22
1
2
4
5
7
8
9
10
11
12
24
19
1
2
3
4
5
6
7
25
10
15
1
2
26
1
2
3
5
6
10
12
Function
Used to check the counter value of each section.
Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing this
count value with the total counter value.)
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
Used to check the total trouble (self diag) history.
Used to check the ROM version of each unit
(section).
Used to display the key operator code
Used to check the number of use of the staple, the
SPF, and scanning.
Used to check the number of use of each paper
feed section. (the number of prints)
Used to check the system configulation.
FAX related counter display
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
Used to display the scanner mode counter.
Used to clear the misfeed counter, the misfeed
history, the trouble counter, and the trouble history.
(The counters are cleared after completion of
maintenance.)
Used to clear the number of use (the number of
prints) of each paper feed section.
Used to clear the number data of use of the staple,
the SPF and scanning.
Used to reset the maintenance counter.
Used to reset the developer counter. (The
developer counter of the DV unit which is installed
is reset.)
Used to reset the copy counter.
Used to clear the OPC drum (membrane
decrease) correction counter. (This simulation is
executed when the OPC drum is replaced.
Used to clear the printer print counter. (The
counter is cleared after completion of
maintenance.)
FAX related counter clear
Used to clear the scanner mode counter.
Used to check the operation of the main drive
(excluding the scanner section) amd to check the
operation of the toner concentration sensor. (The
toner concentration sensor output can be
monitored.)
Used to make the initial setting of toner
concentration when replacing developer.
Used to set options. (This simulation is used to
make option setting when an option is installed.)
Used to detect the paper size.
Used to set the specifications of the auditor.
Setting must be made depending on the use
condition of the auditor.
Used to set the count mode of the total counter
and the maintenance counter.
Used to set the specifications depending on the
destination.
Used to enter the Software Key for the Network
Scanner. (Setup is allowed only when the PCL
board is installed.
Used to input the Software Key for E-MAIL RIC.
Code
Main
Sub
26
14
18
20
22
30
35
36
37
38
46
50
54
57
60
27
30
5
1
40
2
3
41
1
2
3
4
43
44
10
1
AR-235/275 SIMULATION - 4
34
35
40
Function
Used to input the Software Key for the PS
extention kit.
Used to set enable/disable of toner save operation.
Used to set the job separator paper exit mode.
Used to set the specification (language display) for
the destination.
Used to set the operation mode for CE mark.
Used to set the mode of trouble memory.
Used to set whether to stop when the maintenance
life is reached.
Used to set whether to stop when the developer
life is reached.
Used to set whether to stop when the drum life is
reached.
Used to set whether to meet with the output
direction of images regardless of the mode when
installing the finisher.
Used to set whether to use the black/white reverse
function.
Used to set the PWM duty (brightness) at the
center value of the LCD contrast.
Used to set the model code.
Used to set enable/disable of the FAX mode key
when FAX is not installed. (When FAX is installed,
the FAX mode is enabled regardless of this setup.)
Used to set PC/MODEM communication trouble
(U7-00) detection Yes/No.
Used to enter the TAG No. of the copier.
Used to check the operation of sensors and
detectors in the sections other than the paper feed
section of the copier and the related circuit. (The
operation of sensors and detectors can be
monitored with the LCD.)
Used to check the operation of sensors and
detectors in the paper feed section and the related
circuits. (The operations of sensors and detectors
in the paper feed section can be monitored with
the LCD.)
Used to check the operation of the manual paper
feed tray paper size detector and the related
circuit. (The operation of the manual paper feed
tray paper size detector can be monitored with the
LCD.)
Used to adjust the manual paper feed tray paper
width detector detection level.
The AD conversion value of manual feed width
detection is displayed.
Used to check the document size detection photo
sensor.
Used to adjust the detection level of the document
size photo sensor.
Used to check the light reception level and the
detection level of the original size detection photo
sensor.
Used to adjust the detection level of OC 20
degrees.
Used to set the fusing temperature in each
operation mode.
Used to set the paper feed cycle for postcard.
Used to make various setups in each mode of
process control.
Used to adjust the transfer current value.
Correction temperature setup when correcting the
ambient temperature.
Used to set the rotating time before toner supply.
Code
Main
Sub
46
2
7
9
10
11
12
13 to
16
18
19
48
20
30
1
2
3
50
8
9
10
1
5
6
8
9
10
12
51
1
2
8
61
63
1
1
7
64
65
Function
Used to adjust the copy exposure level.
Used to adjust individually the copy exposure
level. (Super photo)
Used to adjust individually the copy exposure
level. (Character)
Used to adjust individually the copy exposure
level. (Character/Photo)
Used to adjust individually the copy exposure
level. (Photo)
FAX exposure level adjustment (batch)
FAX exposure level adjustment (individual)
Used to adjust the copy contrast. (Inclination)
Used to change the image quality in the exposure
mode.
Used to correct SPF exprosure.
Used to set the AE limit.
Used to adjust the copy magnification ratio (main
scanning direction, sub scanning direction).
Used to adjust the scanner magnification ratio
(main/sub scanning direction).
Used to adjust the lead edge/sub scan
magnification ratio.
FAX magnification ratio adjustment (read)
FAX magnification ratio adjustment (print)
FAX auto reduction magnification ratio (print).
Used to adjust the copy lead edge position.
Used to adjust the print image position (top
margin) on the print paper in the print mode.
Used to adjust the print image position (top
margin) on print paper in the copy mode. (SPF/
RSPF)
FAX lead edge adjustment (read)
FAX lead edge adjustment (print)
Used to adjust the print image center position.
(Adjustment can be made for each paper feed
section.)
Used to adjust the print image center position.
(Adjustment can be made for each document
mode.)
Used to adjust the OPC drum separation pawl ON
time.
Used to adjust the contact pressure of paper onto
the resist roller in each section (copier paper feed
section, duplex paper feed section, SPF paper
feed section). (When the print image position
varies greatly for the paper or when a lot of paper
jam troubles occur, the adjustment is required.)
Used to set to disable the operation of the
separation pawl of the photoconductor drum.
Used to test the operation of the LSU.
Used to check the result of shading correction.
(The shading correction data are displayed.)
Used to adjust the SPF white correction start pixel
position automatically.
This adjustment is performed after the lens unit is
replaced.
Used to check the operation of the printer function
(auto print operation).
Used to check the operation panel.
Code
Main
Sub
66
1
2
3
4
6
7
8
10
11
13
67
17
21
22
30
32
34
37
38
41
50
51
52
53
11
14
17
18
20
Function
FAX related soft SW setting
Initial set for the value of the FAX soft SW
FAX PWB memory check
Signal send mode
Printing the confidential password
Image data print
Voice Message send
Image data memory clear
300bps signals send
Send test and adjustment of the dial pulse and
DTMF signal.
DTMF signal send
FAX information print
Handset sound volume adjustment
TEL/LIU state change recognition
Receive data check
Communication time measurement display
Speaker sound volume adjustment
Time setting/check
CI signal check
FAST SRAM clear
Signal detection check
Pseudo-ringer check
SRAM backup
Used to set the Select-IN signal.
Used to check write/comparison of flash programs.
Used to clear NVRAM.
Used to clear the data area for FLASH ROM
Network Scanner Application.
Used to check the network connection when a
scanner option is installed.
3. Details
1
1-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the scanner unit and its
control circuit.
Optical (Image scanning)
Operation
AR-235/275 SIMULATION - 5
Magnification ratio
Default
Document size
Set number of times
25% to 400%
100%
Varies depending on the destination.
1 to 999 (0: Continuous operation)
1-2
Operation test/check
Purpose
Used to check the operation of sensor and detector in
Function
(Purpose) the scanning (read) section and the related circuit.
Optical (Image scanning)
Section
Operation
Item
Operation/procedure
The status of sensors and detectors in the scanner section is displayed. The active sensors and detectors are highlighted.
Sim1-2 SENSOR CHECK
MHPS
EMPS
DLS1
DLS2
DWS1
DWS2
DWS3
FGOD
DFD
RDD
OPCLS
Empty sensor
Tray length sensor (small)
Tray length sensor (large)
Tray width sensor (small)
Tray width sensor (middle)
Tray width sensor (large)
Paper feed cover sensor
Document entry detection sensor
Document exit sensor
Book sensor
Purpose
Function
(Purpose)
Section
Item
Operation/procedure (Pattern 9)
2-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the loads in the SPF
unit and the control circuits.
SPF
Operation
Operation test/check
Used to check the operation of the SPF unit and the
related circuit.
SPF
Operation
The names of the loads which can be operated are displayed. Select
the load to be checked with the 10-key.
(Initial screen)
(Executing screen)
Sim2-3 OUTPUT CHECK
1:DTM-F 4:CLH
2:DTM-R 5:GSOL
3:DFSOL 6:RSOL
EXEC
2
1:DTM-F
2:DTM-R
3:DFSOL
4:CLH
5:GSOL
6:RSOL
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
Note: Executable only when the SPF/RSPF is installed.
50% to 200%
100%
Varies depending on the destination.
Selectable only when RSPF is installed, fixed
(single) for SPF.
1 to 999 (0: Continuous operation)
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of sensor and detector in
the finisher and the related circuit.
Sorter/Finisher
Operation
Operation/procedure
2-2
Purpose
Function
(Purpose)
Section
Item
3-2
Operation test/check
Used to check the operation of sensors and detectors
in the SPF unit and the related circuit.
SPF
Operation
Operation/procedure
The operations of sensors and detectors in the SPFsection are displayed.
AR-235/275 SIMULATION - 6
INPD
FWPS
JGHP1
JGHP2
JGPD
T1OD
T1PF
PGOP
T2OD
OFHP
T2UP
T2DN
JGDSW
EVRE
STHP
READY
LSTS
NCTS
STND
T2PUD
3-6
Adjustment
Purpose
Used to adjust the finisher jogger position.
Function
(Purpose)
Sorter/Finisher
Section
Operation
Item
Operation/procedure (Pattern 4)
After the paper size is set, the side guide plate and the rear guide plate
are set.
Shifts to the specified paper size position.
(Initial screen)
(Input screen)
Sim3-6 JOGGER ADJ.
1:PAPER SIZE
2:JOGGER POS X
3:JOGGER POS Y
1
Operation test/check
Used to check the operation of the load in the finisher
and the control circuit.
Sorter/Finisher
Operation
Operation/procedure (Pattern 9)
The names of the loads which can be operated are displayed. Select
the load to be checked with the key.
(Initial screen)
(Executing screen)
Sim3-3 OUTPUT CHECK
1:JGM1
4:FM-1200
2:JGM2
5:EVM
3:FM-600 6:OFM
1/3
EXEC
2:JOGGER POS X
3:JOGGER POS Y
EXEC [ 0- 99]
EXEC [ 0- 99]
50
Content
Paper size
(1:A3, 2:A4, 3:B4, 4:B5,
5:A4R, 6:WLT, 7:LT, 8:LG,
9:FC, 10:LTR, 11:8K,
12:16K)
Side guide plate
Rear edge guide plate
Setting
range
1-12
50
Default
1-99
50
Example: When the side guide plate value is adjusted in A3, the same
adjustment is made in A4. (Value 1 in the table)
Paper size
A3
A4
B4
B5
A4R
WLT
LT
LG
FC
LTR
8K
16K
1
1
3
3
5
2
2
4
4
4
6
6
There are 6 adjustment values for the side guide plate, and 12 for the
rear guide plate. The adjustment position is determined from the table
below according to the paper size.
Display items
1:PAPER SIZE
(Executing screen)
Adjustment
Used to adjust the offset tray operations.
Operation
Operation/procedure
The finisher main motor operates for 10sec, the staple motor 5 times,
the tray lift-up motor one reciprocating operation, other motors max. 20
reciprocating operations from the home position, the solenoid repeats
500msec ON and 500msec OFF 20 times.
The staple operation motor operates only when there is no cartridge
installed.
(Initial screen)
Sim3-7 OFFSET ADJ.
1:PAPER PUSH TMG 50
2:PAPER OUT DOWN 1
3:STAPLE UP
6
1/2
AR-235/275 SIMULATION - 7
[ 34- 66]
50
EXEC [ 0- 99]
13
Display items
1:PAPER PUSH TMG
3:STAPLE UP
4:STAPLE DOWN
5:OFFSET INI.POS
Content
Installation
range
34-66
Default
Paper holder
50
descending timing in
non-staple
Used to adjust the descending timing of the
paper holder lever before lift-up operation
after paper exit or offset operation. (The
paper holder lever prevents against paper
shift in paper top surface detection and paper
stacking .)
Tray descending
0-12
1
distance after nonstaple paper exit
Used to adjust the offset tray descending
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
Tray lift distance
0-12
6
before staple paper
exit
The height of the tray standby position in
stapling is changed for that in non-stapling to
improve stacking capacity in stapling. (The
relative distance for the height of the tray
standby position in non-stapling is set.)
Tray descending
0-12
6
distance after staple
paper exit
Used to adjust the offset tray descending
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
Offset tray shift
0-99
13
position adjustment
Used to shift the offset tray to the shipment
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
(In the case of 0 - 94 (Shipment position: 13))
1) Initialize the offset tray normally.
2) The tray descends to the parameter position + 1 pulse position.
3) The tray lifts up to the specified parameter position.
(Disassembly position: 94 - 99)
1) The tray descends to the bottom.
* If there is some paper in the offset tray, the
tray cannot descend to the specified position. Check to insure that there is no paper
in the tray before execution.
(Initial screen)
(Executing screen)
1:F-R
2:HP CHECK
[Selection 2]
Reciprocating operation
Home position check
(Input/Selection screen)
Sim3-11 SHIFTER CHK
SFTHP
SFTHP:
[] key
[] key
[] key
4
4-2
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of sensor and detector in
the option tray and the related circuit.
Paper feed
Operation
Operation/procedure
The operating states of the sensor and the detector are displayed.
The active sensors and detectors are highlighted.
Sim4-2 SENSOR CHECK
PED2 LUD2 PFD2 CD2
PED3 LUD3 PFD3 CD3
PED4 LUD4 PFD4 CD4
DSWR2 DSWR3 DSWR4
PED2
LUD2
PFD2
CD2
PED3
LUD3
PFD3
CD3
PED4
LUD4
PFD4
CD4
DSWR3
DSWR2
DSWR4
Operation test/check
Used to check the operation of the shifter.
Operation
4-3
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the load in the option
tray and the control circuit.
Paper feed
Operation
Operation/procedure (Pattern 9)
Select the load to check with the 10-key.
During execution of load operation, [EXEC] is highlighted.
Pressing the [BACK] key under this state interrupts the operation.
AR-235/275 SIMULATION - 8
(Initial screen)
(Initial screen)
(Executing screen)
(Executing screen)
PRESS OK KEY
EXEC
EXEC
5-3
Operation test/check
Purpose
Used to check the operation of the copy lamp and the
Function
(Purpose) control circuit.
Optical (Image scanning)
Section
Operation
Item
Operation/procedure (Pattern 8)
Press the [OK] key.
The copy lamp lights up for 10 sec.
(Initial screen)
(Executing screen)
Sim5-3 COPY LAMP
The lift-up motor operates only when the tray is opened. (20 times)
Note: Execution is possible only when the option cassette is installed.
PRESS OK KEY
EXEC
EXEC
5
6
5-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the display, LCD in the
operation panel, and control circuit.
Operation (screen/operation)
Operation
Operation/procedure
The LCD is displayed as follows. (All LEDs are ON.)
(Initial screen)
With the upper half section highlighted,
Sim5-1 LCD/LED CHK.
contrast changes "Standard MAX MIN." in
every 2sec.
(6 sec later)
Sim5-1 LCD/LED CHK.
(6 sec later)
Sim5-1 LCD/LED CHK.
5-2
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the heater lamp and the
control circuit.
Fixing (Fusing)
Operation
Operation/procedure (Pattern 8)
Press the [OK] key.
ON/OFF operation of the heater lamp is repeated 5 times in an interval
of 500ms.
6-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the loads (clutches and
solenoids) in the paper transport system and the
control circuit.
Paper transport (Discharge/Switchback/Transport)
Operation
Operation/procedure (Pattern 9)
The names of the loads which can be operated are displayed. Select
the load to be checked with the 10-key.
(Initial screen)
(Executing screen)
Sim6-1 OUTPUT CHECK
1:LUM1
4:MPFS
2:CPFC1 5:RRC
3:CPFS1 6:PSPS
1/2
EXEC
1:LUM1
2:CPFC1
3:CPFS1
4:MPFS
5:RRC
6:PSPS
7:OGS
8:LUM2
9:CPFC2
10:CPFS2
11:TRC2
12:LUM3
13:CPFC3
14:CPFS3
15:TRC3
16:LUM4
17:CPFC4
18:CPFS4
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
The lift-up motor operates only when the tray is opened.
AR-235/275 SIMULATION - 9
7-6
6-2
Operation test/check
Purpose
Used to check the operation of each fan motor and its
Function
(Purpose) control circuit.
Others
Section
Operation
Item
Operation/procedure (Pattern 9)
The names of the loads which can be operated are displayed. Select
the load to be checked with the key.
(Initial screen)
(Executing screen)
Sim6-2 FAN MOTOR
1:VFM
2:DCFM&DCFM2
3:VFM&DCFM&DCFM2
EXEC
2
3:VFM&DCFM&DCFM2
Enter the interval aging cycle time (sec) with the 10-key pad . Refer to
7-1.
Sim7-6 INTERVAL SET
AGING INTERVAL
3
[ 1-255]
Setting/Operation test/check
Purpose
Used to set the cycle of intermittent aging.
Function
(Purpose)
Operation
Item
Operation/procedure (Pattern 1)
Setting range
Default
1-255
3
7-8
Purpose
Function
(Purpose)
Item
Setting/Operation test/check
Used to set the display of the warm-up time.
Operation
Operation/procedure
7-1
(Initial screen)
Purpose
Function
(Purpose)
Item
Setting/Operation test/check
Used to set the aging operation conditions.
(Executing screen)
Operation
1
Operation/procedure
Select with the 10-key.
4:INTERVL
5:WARMUP
6:DV CHK.
If the [CA] key is pressed at this time, count-up is interrupted to terminate the simulation. (However, warm-up is continued.)
1:AGING
2:MISFEED
3:FUSING
After completion of warming up, "WARM UP COMPLETED" is displayed and the control returns to the initial screen.
Press [CA] key, and the simulation will be terminated and copying will
be made with the set contents.
When selected without setup, the selected value is registered and
highlighted. When selected with previous setup, the previous setup is
canceled and it is displayed normally.
This setting is canceled by power OFF.
Note: In SIM 7-1, pressing [CA] key terminates the simulation and the
machine enters the aging mode without resetting. Therefore, to
perform "4. Intermittent setup," the intermittent cycle must be set
with SIM 7-6 in advance.
Reset is not performed when the machine enters the aging
mode.
8
8-1
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the
developing bias voltage in each copy mode and the
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Developer/Toner hopper
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-1 DV BIAS
1:AE
2:TEXT
3:TEXT/PHOTO
1/2
AR-235/275 SIMULATION - 10
COPY
426
450
450
Display items
Installation
range
200-550
Content
Default
1:AE
AE ()
426 (426V)
2:TEXT
Character
450 (450V)
3:TEXT/PHOTO
Character/Photo
450 (450V)
4:PHOTO
Photo
450 (450V)
5:SUPER PHOTO Super photo
400 (400V)
6:TONER SAVE
Toner save
376 (376V)
() Linked with the destinations of SIM 26-6.
Linked with the auto exposure mode of SIM 46-19-1.
The minimum increment is 2V.
The result of (Set value 199) / 2 is stored in the EEPROM.
When reading a value from the EEPROM, the value of (EEP value *2)
+ 200 is used as the set value.
Therefore, the set value entered must be an even number. If an odd
number is entered the entered odd number + 1 is displayed after
pressing [OK] key.
8-3
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each copy mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Section
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
Purpose
Function
(Purpose)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of 25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-3 MHV(L) COPY
1:AE
3
2:TEXT
5
3:TEXT/PHOTO
5
1/2
EXEC [ 1- 8]
EXEC [ 1- 8]
8-2
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each copy mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of 25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-2 MHV(H) COPY
1:AE
3
2:TEXT
5
3:TEXT/PHOTO
5
1/2
Display items
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
EXEC [ 1- 8]
EXEC [ 1- 8]
Content
AE ()
Character
Character/Photo
Photo
Super photo
Toner save
Setting
range
1-8
Default
4 (555V)
5 (580V)
5 (580V)
5 (580V)
3 (530V)
2 (505V)
Set value
480
505
530
555
580
605
630
655
Grid High
480V
505V
530V
555V
580V
605V
630V
655V
Display items
Content
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
AE ()
Character
Character/Photo
Photo
Super photo
Toner save
Setting
range
1-8
Default
4 (425V)
5 (450V)
5 (450V)
5 (450V)
3 (400V)
2 (375V)
Set value
480
505
530
555
580
605
630
655
Grid High
480V
505V
530V
555V
580V
605V
630V
655V
Grid Low
350V
375V
400V
425V
450V
475V
500V
525V
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to 480V (pattern 1), the
grid low voltage is 350V.
8-10
Grid Low
350V
375V
400V
425V
450V
475V
500V
525V
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the
developing bias voltage in each printer mode and the
control circuit.
Image process (Photoconductor/Developping/
Transfer/Cleaning)
Developer/Toner hopper
Operation/procedure (Pattern 4)
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to 480V (pattern 1), the
grid low voltage is 350V.
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-10 DV BIAS
1:DENS1(600)
2:DENS2(600)
3:DENS3(600)
1/4
AR-235/275 SIMULATION - 11
PRT
400
450
450
Display items
Installation
range
200-550
Content
Default
1:DENS1(600)
Density 1 (600dpi)
400 (400V)
2:DENS2(600)
Density 2 (600dpi)
450 (450V)
3:DENS3(600)
Density 3 (600dpi)
450 (450V)
4:DENS4(600)
Density 4 (600dpi)
450 (450V)
5:DENS5(600)
Density 5 (600dpi)
500 (500V)
6:TS(600)
Toner save (600dpi)
350 (350V)
7:DENS1(1200)
Density 1 (1200dpi)
300 (300V)
8:DENS2(1200)
Density 2 (1200dpi)
350 (350V)
9:DENS3(1200)
Density 3 (1200dpi)
376 (376V)
10:DENS4(1200) Density 4 (1200dpi)
426 (426V)
11:DENS5(1200) Density 5 (1200dpi)
500 (500V)
The minimum increment is 2V.
The result of (Set value 199) / 2 is stored in the EEPROM.
When reading a value from the EEPROM, the value of (EEP value *2)
+ 200 is used as the set value.
Therefore, the set value entered must be an even number. If an odd
number is entered the entered odd number + 1 is displayed after
pressing [OK] key.
8-11
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each printer mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of 25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-11 MHV(H) PRT
1:DENS1(600)
3
2:DENS2(600)
5
3:DENS3(600)
5
1/4
EXEC [ 1- 8]
EXEC [ 1- 8]
Display items
Content
1:DENS1(600)
2:DENS2(600)
3:DENS3(600)
4:DENS4(600)
5:DENS5(600)
6:TS(600)
7:DENS1(1200)
8:DENS2(1200)
9:DENS3(1200)
10:DENS4(1200)
11:DENS5(1200)
Density 1 (600dpi)
Density 2 (600dpi)
Density 3 (600dpi)
Density 4 (600dpi)
Density 5 (600dpi)
Toner save (600dpi)
Density 1 (1200dpi)
Density 2 (1200dpi)
Density 3 (1200dpi)
Density 4 (1200dpi)
Density 5 (1200dpi)
NO.
1
2
3
4
5
6
7
8
Grid High
480V
505V
530V
555V
580V
605V
630V
655V
Set value
480
505
530
555
580
605
630
655
Installation
range
1-8
Default
5 (580V)
5 (580V)
5 (580V)
5 (580V)
7 (630V)
3 (530V)
1 (480V)
3 (530V)
4 (555V)
5 (580V)
7 (630V)
Grid Low
350V
375V
400V
425V
450V
475V
500V
525V
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to 480V (pattern 1), the
grid low voltage is 350V.
8-12
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each printer mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of 25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-12 MHV(L) PRT
1:DENS1(600)
3
2:DENS2(600)
5
3:DENS3(600)
5
1/4
Display items
EXEC [ 1- 8]
EXEC [ 1- 8]
Content
1:DENS1(600)
2:DENS2(600)
3:DENS3(600)
4:DENS4(600)
5:DENS5(600)
6:TS(600)
7:DENS1(1200)
8:DENS2(1200)
9:DENS3(1200)
10:DENS4(1200)
11:DENS5(1200)
Density 1 (600dpi)
Density 2 (600dpi)
Density 3 (600dpi)
Density 4 (600dpi)
Density 5 (600dpi)
Toner save (600dpi)
Density 1 (1200dpi)
Density 2 (1200dpi)
Density 3 (1200dpi)
Density 4 (1200dpi)
Density 5 (1200dpi)
NO.
1
2
3
4
5
6
7
8
Grid High
480V
505V
530V
555V
580V
605V
630V
655V
Set value
480
505
530
555
580
605
630
655
Installation
range
1-8
Default
5 (450V)
5 (450V)
5 (450V)
5 (450V)
7 (500V)
3 (400V)
1 (350V)
3 (400V)
4 (425V)
5 (450V)
7 (500V)
Grid Low
350V
375V
400V
425V
450V
475V
500V
525V
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to 480V (pattern 1), the
grid low voltage is 350V.
8-13
Purpose
Function
(Purpose)
Section
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
Adjustment/Operation test/check
Used to check and adjust the operation of the
developing bias voltage in FAX mode and the control
circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Developer/Toner hopper
Operation/procedure (Pattern 3)
Enter the adjustment value and press the [OK] key, and output operation is performed for 30sec.
AR-235/275 SIMULATION - 12
(Initial screen)
(Initial screen)
(Executing screen)
(Executing screen)
EXEC [ 1- 8]
EXEC [ 1- 8]
Setting range
Default
1-8
5
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (high mode) in FAX mode and the
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 3)
Enter the adjustment value and press the [OK] key, and output operation is performed for 30sec.
(Initial screen)
(Executing screen)
Sim8-14 MHV(H) FAX
FAX
5
EXEC [ 1- 8]
EXEC [ 1- 8]
Setting range
Default
1-8
5
NO.
Set value
Grid High
Grid Low
1
480
480V
350V
2
505
505V
375V
3
530
530V
400V
4
555
555V
425V
5
580
580V
450V
6
605
605V
475V
7
630
630V
500V
8
655
655V
525V
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to 480V (pattern 1), the
grid low voltage is 350V.
9
9-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check and adjust the operation of the load
(motor) in the duplex section and the control circuit.
Duplex
Operation
Operation/procedure (Pattern 9)
NO.
1
2
3
4
5
6
7
8
Set value
480
505
530
555
580
605
630
655
Grid High
480V
505V
530V
555V
580V
605V
630V
655V
Grid Low
350V
375V
400V
425V
450V
475V
500V
525V
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to 480V (pattern 1), the
grid low voltage is 350V.
8-15
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (low mode) in FAX mode and the
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 3)
Enter the adjustment value and press the [OK] key, and output operation is performed for 30sec.
1:DMF600
2:DMF1200
3:DMR600
4:DMR1200
9-4
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to adjust the rotation speed of the duplex motor.
Duplex
Operation
Operation/procedure (Pattern 1)
Set the rotation speed of the duplex motor.
Sim9-4 MOTOR SPEED
MOTOR SPEED
3
[ 1- 13]
Setting range
Default
AR-235/275 SIMULATION - 13
1-13
3
9-5
16
Adjustment
Purpose
Used to adjust the switch back time of the duplex
Function
(Purpose) motor.
Operation/procedure (Pattern 2)
Set the switch back time of the duplex motor.
(Initial screen)
(Input screen)
Sim9-5 SW BACK TIME
1:600dpi
50
2:1200dpi
50
1
Display items
1:600dpi
2:1200dpi
16-0
Clear/Cancel (Trouble etc.)
Purpose
Used to cancel the self-diag U2 trouble.
Function
(Purpose)
Trouble
Error
Item
Operation/procedure (Pattern 6)
When the [OK] key is pressed, the trouble is canceled.
(Initial screen)
(Process check screen)
[ 18- 76]
Installation range
18-76
50
Default
50
50
10
PRESS OK KEY
17
10-0
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the toner motor and its
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Developer/Toner hopper
Operation
Operation/procedure (Pattern 8)
Press the [OK] key and operate the toner motor for 30 sec.
Pressing the [INTERRUPT] key interrupts the operation, and the display returns to the main code entry screen.
(Initial screen)
(Executing screen)
Sim10 TONER MOTOR
PRESS OK KEY
17-0
Purpose
Function
(Purpose)
Item
Error
Operation/Procedure (Pattern 6)
When the [OK] key is pressed, the trouble is canceled.
(Initial screen)
(Execution check screen)
Sim17 TROUBLE CLEAR
PF TROUBLE CLEAR
PRESS OK KEY
EXEC
21
EXEC
21-1
Purpose
Function
(Purpose)
Item
14
14-0
Purpose
Function
(Purpose)
Item
Error
Operation/procedure (Pattern 6)
When the [OK] key is pressed, the trouble is canceled.
(Initial screen)
(Process check screen)
Sim14 TROUBLE CLEAR
TROUBLE CLEAR
(WITHOUT U2,PF)
PRESS OK KEY
Setting
Used to set the maintenance cycle.
Specifications
Counter
Operation/procedure (Pattern 1)
Enter the adjustment value and press the [OK] key.
Sim21-1 CYCLE SET.
MAINTE CYCLE
0
(0:5K 1:12.5K
2:25K 3:50K 4:FREE)
[ 0- 4]
0
Item
0
1
2
3
4
Content
5K
12.5K
25K
50K
FREE
AR-235/275 SIMULATION - 14
Setting range
0-4
Default
3
22
22-1
Adjustment/setting/operation data output/check
(display/print)
Used to check the counter value of each section.
Purpose
Function
(Purpose)
Counter
Item
Operation/procedure
Counter is displayed.
Sim22-1
TOTAL
MAINTE
DEVE
DRUM
COUNTER 1/3
: nnnnnnn
: nnnnnnn
: nnnnnnn
: nnnnnnn
Total
Maintenance
Developer counter
Drum counter
Copy counter
Printer counter
TOTAL
MAINTE
DEVE
DRUM
COPY
PRINTER
IMC
DUPLEX
IMC counter
Duplex counter
OTHERS
FAX SEND
FAX RCV
22-2
Purpose
Function
(Purpose)
Item
Operation/procedure
Counter data is displayed.
Sim22-2
JAM
SPF JAM
TROUBLE
JAM/TROUBLE
: nnnnnnn
: nnnnnnn
: nnnnnnn
JAM
SPF JAM
TROUBLE
JAM counter
SPF JAM counter
Trouble counter
Function
(Purpose)
Item
Jam contents
1st cassette pick-up miss
2nd cassette pick-up miss
3rd cassette pick-up miss
4th cassette pick-up miss
Multi manual feed pick-up miss
Paper-in sensor lead edge jam
Paper-in sensor rear edge jam
Paper-in sensor reverse jam
Duplex sensor lead edge jam
Duplex sensor rear edge jam
Upper stage paper exit lead edge jam
Upper stage paper exit rear edge jam
Lower stage paper exit lead edge jam
Lower stage paper exit rear edge jam
Abnormality between PS papers.
2nd paper pass lead edge jam
2nd paper pass rear edge jam
3rd paper pass lead edge jam
3rd paper pass rear edge jam
4th paper pass lead edge jam
4th paper pass rear edge jam
Duplex short scale error
Duplex long scale error
Duplex print remain (double feed) jam
Finisher paper entry jam
Finisher escape tray jam
Finisher offset tray jam
Finisher staple tray jam
22-4
Adjustment/setting/operation data output/check
(display/print)
Used to check the total trouble (self diag) history.
Purpose
Function
(Purpose)
Trouble
Item
Operation/procedure
The trouble error codes are displayed in the sequence of the latest one
first. Max. 40 items of information are stored. (Older ones are deleted
in sequence.) The machine condition can be estimated by this data.
Sim22-4 TROUBLE 1/4
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
22-3
Purpose
Display items
1ST_PICK
2ND_PICK
3RD_PICK
4TH_PICK
HND_PICK
PIN_TOP
PIN_END
PIN_DUP
DPX_TOP
DPX_END
UPO_TOP
UPO_END
LPO_TOP
LPO_END
PS
2ND_TOP
2ND_END
3RD_TOP
3RD_END
4TH_TOP
4TH_END
DPX_SHORT
DPX_LONG
DPX_DBLFD
FIN_PIN
FIN_ESC
FIN_OFST
FIN_STPL
Operation/procedure
The misfeed history is displayed in the sequence of recentness by the
name of sensors and detectors. Max. 40 items of information can be
stored in memory. (The old ones are deleted sequentially.) The trouble
section may be determined by the data.
Sim22-3 JAM HIS.1/5
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
22-5
Purpose
Function
(Purpose)
Item
Adjustment/Setting/Check
Used to check the ROM version of each unit (section).
Software
Operation/procedure
ROM and CPU data of each section are displayed.
Sim22-5
S/N
MCU
IMC
OPE
ROM VER.1/2
:0000000000
:00.00
:00.00
:00.00
[Display example]
ROM version 1.250 [1.25] (upto 2 decimal places)
The display of the protocol monitor and the soft SW follows this display.
S/N
MCU
IMC
OPE
AR-235/275 SIMULATION - 15
PRINTER
NIC
FINISHER
FAX
PRINTER
NIC
FINISHER
FAX
22-7
Sim22-10 SYSTEM 1/4
SPEED : XXXXXXX
DF
: XXXXXXX
OUTPUT : XXXXXXX
CASETTE1: XXXXXXX
22-8
Purpose
Function
(Purpose)
Item
Operation/procedure
SPF
SCAN
STAPLE
ORG./STAPLE
: nnnnnnn
: nnnnnnn
: nnnnnnn
SPF counter
Scan counter
Stapler counter
22-9
Purpose
Function
(Purpose)
Section
Item
Display items
23CPM/25CPM/27CPM
NONE/[1: SPF]/[2: RSPF]
NONE/[3: Finisher]/[4: Job separator]
NONE/[5: One-step paper feed unit]
NONE/[6: Two-step paper feed unit]
NONE/Expansion memory capacity (MB)
NONE/[7: PCL]
NONE/[8: PS3]
NONE/[9: NIC]
NONE/[10: SCANNER]
NONE/[11: FAX]
NONE/Memory capacity (MB)
NONE/[12: Handset]
Display items
SPEED
DF
OUTPUT
CASETTE1
CASETTE2
IMC MEM
PCL
PS3
NIC
SCANNER
FAX
FAX MEM
HAND SET
No.
Item
1
2
3
4
5
6
7
8
9
10
11
12
SPF
RSPF
Finisher
Job separator
1 tray paper feed unit
2 tray paper feed unit
PCL
PS3
NIC
SCANNER
FAX
Handset
Model code
AR model
DM model
AR-SP4
DM-SP2
AR-RP3
DM-RP1
AR-FN5
DM-FN1
AR-TR3
STANDARD
AR-D11 (*1)
DM-DE3 (*1)
AR-D12 (*1)
DE-DE4 (*)
AR-P11
STANDARD
AR-PK1
STANDARD
AR-NC5J
STANDARD
AR-NS2
DM-NS1
AR-FX4
DM-FX2
AR-HN4
Operation/procedure
The data shows the use frequency of each paper feed section.
Sim22-9
BYPASS
TRAY1
TRAY2
TRAY3
BYPASS
TRAY1
TRAY2
Purpose
Function
(Purpose)
FEED
1/2
: nnnnnnn
: nnnnnnn
: nnnnnnn
: nnnnnnn
Function
(Purpose)
Item
Adjustment/Setting/Check
FAX related counter display
Operation/procedure
TRAY3
TRAY4
Tray 3 counter
Tray 4 counter
22-10
Purpose
22-11
Purpose
Function
(Purpose)
Option
Operation/procedure
The detected machine composition is displayed.
Section
Item
Operation/procedure
Fourty SPF JAM history datas are displayed sequentially from the latest.
AR-235/275 SIMULATION - 16
(Initial screen)
Sim22-12 SPF JAM1/5
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
Display items
PI_TOP
PI_END
PO_TOP
PO_END
JAM_REV
ORG_SHORT
ORG_LONG
1:BYPASS
2:TRAY1
3:TRAY2
Jam contents
SPF paper-in lead edge jam
SPF paper-in rear edge jam
SPF paper-out lead edge jam
SPF paper-out rear edge jam
SPF duplex reversion jam
SPF short scale error
SPF long scale error
Function
(Purpose)
Item
4:TRAY3
5:TRAY4
Tray 3 counter
Tray 4 counter
24-3
Data clear
Purpose
Used to clear the number data of use of the staple, the
Function
(Purpose) SPF and scanning.
Counter
Item
Operation/procedure (Pattern 7)
22-19
Purpose
(Check screen)
Operation/procedure
Counter data is displayed.
1:SPF
2:SCAN
3:STAPLE
SPF counter
Scan counter
Stapler counter
24-4
SCANMODE
Purpose
Function
(Purpose)
Item
Data clear
Used to reset the maintenance counter.
Counter
24
Operation/procedure (Pattern 6)
24-1
Purpose
Function
(Purpose)
Item
Data clear
Used to clear the misfeed counter, the misfeed history,
the trouble counter, and the trouble history. (The
counters are cleared after completion of maintenance.)
Counter
Operation/procedure (Pattern 7)
Each counter is cleared individually. (The history of each counter is
deleted when clearing)
(Initial screen)
(Check screen)
Sim24-1 COUNTER CLR
1:JAM
2:SPF JAM
3:TROUBLE
2
1:JAM
2:SPF JAM
3:TROUBLE
PRESS OK KEY
24-5
Purpose
Function
(Purpose)
Section
Item
Data clear
Used to reset the developer counter. (The developer
counter of the DV unit which is installed is reset.)
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Developer/Toner hopper
Counter
Developer
Data clear
Used to clear the number of use (the number of prints)
of each paper feed section.
Paper feed
Counter
Operation/procedure (Pattern 7)
Operation/procedure (Pattern 6)
24-2
Purpose
Function
(Purpose)
Section
Item
(Check screen)
(Check screen)
PRESS OK KEY
24-6
Purpose
Function
(Purpose)
Item
AR-235/275 SIMULATION - 17
Data clear
Used to reset the copy counter.
Counter
Copier
Operation/procedure (Pattern 6)
Operation/procedure (Pattern 6)
PRESS OK KEY
The scanner mode counter and the number of send of the scanner are
cleared.
(Initial screen)
(Process check screen)
Sim24-15 COUNTERCLR
SCANNER MODE
COUNTER CLEAR
Sim24-15 COUNTERCLR
SCANNER MODE
COUNTER CLEAR
PRESS OK KEY
24-7
Purpose
Function
(Purpose)
Section
Item
Data clear
Used to clear the OPC drum (membrane decrease)
correction counter. (This simulation is executed when
the OPC drum is replaced.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Photo conductor
Counter
Operation/procedure (Pattern 6)
Press the [OK] key.
(Initial screen)
(Check screen)
PRESS OK KEY
25
25-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the main drive
(excluding the scanner section) and to check the
operation of the toner concentration sensor. (The toner
concentration sensor output can be monitored.)
DRIVE
Operation
Operation/procedure
The operation of the drive system is checked.
Toner density control sensor value is displayed.
Select the mode with the 10-key and press the [OK] key, and the main
motor will rotate and the toner concentration control sensor value will
be displayed.
24-9
Purpose
Function
(Purpose)
Section
Item
Data clear
Used to clear the printer print counter. (The counter is
cleared after completion of maintenance.)
Printer
Counter
Printer
Operation/procedure (Pattern 7)
After execution, interruption cannot be made for about 7 sec. ([CA] key,
[INTERRUPT] key, and [BACK] key are invalid.)
(Initial screen)
(Executing screen)
Sim25-1 MAIN MOTOR
1:600dpi
2:1200dpi
1:PRINTER
2:IMC
3:DUPLEX
4:OTHERS
EXEC
25-2
Purpose
Function
(Purpose)
Section
Printer counter
IMC counter
DUPLEX counter
The other counters
Setting
Used to make the initial setting of toner concentration
when replacing developer.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Developer/Toner hopper
Operation/procedure
1) Open the cover.
24-10
Purpose
Function
(Purpose)
Adjustment/Setting/Check
FAX related counter clear
Operation/procedure
24-15
EU error occurs when the finally calculated toner concentration reference value is 179 or greater.
Purpose
Function
(Purpose)
Item
Data clear
Used to clear the scanner mode counter.
Sampling is made 54 times every 600ms, and the average of the last
three times in the last 1.8sec of 3min is stored.
EL error occurs when the finally calculated toner concentration reference value is 77 or smaller.
Counter
AR-235/275 SIMULATION - 18
(Initial screen)
(Executing screen)
26
26-1
[128]
Setting
Purpose
Used to set options. (This simulation is used to make
Function
(Purpose) option setting when an option is installed.)
Specifications
Option
Item
Operation/procedure (Pattern 1)
PRESS OK KEY
EXEC
EXEC
Error content:
Set value
0
1
Connection option
None (default)
Job separator provided.
26-2
Purpose
Function
(Purpose)
Section
Item
Setting
Used to detect the paper size.
Paper feed
Specifications
Operation/procedure (Pattern 2)
Used to set the automatic size detection.
Setting to detect B4/Legal as FC
0: B4 legal is detected as B4 legal.
1: B4 legal is detected as FC.
2:A4<->LT
This setup detects Letter as A4 in the inch series and
A4 as Letter in the AB series.
0: Detection disable
1: Detection valid
(Initial screen)
(Input screen)
1:B4/LG,FC
Error content:
"EL ERROR"
Error content:
Document
table/SPF
Set value
0
1
Setup
Detection invalid
Detection valid
Remarks
Default
Document size
AB series (Japan)
FC (8.5 x 13)
LG (8.5 x 14)
B4
FC (8.5 x 13)
LG (8.5 x 14)
B4
FC (8.5 x 13)
LG (8.5 x 14)
B4
Set value
0
1
(Invalid)
(Valid)
B4
B4
B4
B4
B4
B4
B4
FC (8.5 x 13)
B4
FC (8.5 x 13)
B4
FC (8.5 x 13)
LG (8.5 x 14) FC (8.5 x 13)
LG (8.5 x 14) FC (8.5 x 13)
WLT (11 x 17) WLT (11 x 17)
Inch series
Machine paper
feed cassette
Manual paper
feed tray
AB series
Paper
[ 0- 1]
All destinations
Japan (AB series)
AB series
Inch series
AR-235/275 SIMULATION - 19
FC (8.5 x 13)
LG (8.5 x 14)
B4
FC (8.5 x 13)
LG (8.5 x 14)
B4
FC (8.5 x 13)
LG (8.5 x 14)
B4
LG (8.5 x 14)
LG (8.5 x 14)
B4
LG (8.5 x 14)
LG (8.5 x 14)
B4
LG (8.5 x 14)
LG (8.5 x 14)
B4
LG (8.5 x 14)
LG (8.5 x 14)
B4
FC (8.5 x 13)
FC (8.5 x 13)
B4
FC (8.5 x 13)
FC (8.5 x 13)
B4
Setup
Detection invalid
Detection valid
Remarks
Default
Document
table/SPF
Destination
AB series
Inch series
Paper
Machine paper
feed cassette
Manual paper
feed tray
A4
LT (8.5 x 11)
A4
LT (8.5 x 11)
Set value
0
1
(Invalid)
(Valid)
A4
LT (8.5 x 11)
A4
LT (8.5 x 11)
LT (8.5 x 11)
A4
LT (8.5 x 11)
A4
Document size
All destinations
All destinations
26-3
Purpose
Function
(Purpose)
Section
Item
26-6
Setting
Used to set the specifications of the auditor. Setting
must be made depending on the use condition of the
auditor.
Auditor
Specifications
Purpose
Function (Purpose)
Item
Setting
Used to set the specifications depending on
the destination.
Specifications
Destination
Operation/procedure (Pattern 1)
Select the destination.
Operation/procedure (Pattern 1)
Sim26-6 DESTINATION
DESTINATION
0
(0:JAPAN 1:SEC
2:SECL 3:SEEG 4:SUK
1/3 [ 0- 13]
0
Display
items
0:P10
1:VENDOR
2:OTHER
Content
Built-in auditor mode
Coin vendor mode
Others
Setting
range
0-2
Default
0
26-5
Purpose
Function
(Purpose)
Item
Setting
Used to set the count mode of the total counter and the
maintenance counter.
Specifications
Counter
Operation/procedure (Pattern 2)
Used to set the count up number (1 or 2) when an A3/WLT paper
passes through.
For the drum counter and the developer counter, double count is
employed unconditionally.
(Target counter selection)
1:TOTAL COUNTER
2:MAINTE COUNTER
Total
Maintenance
Single count
Double count
Setting range
Default
(Initial screen)
1-2
2
(Input screen)
Display
items
0:JAPAN
1:SEC
2:SECL
3:SEEG
4:SUK
5:SCA
6:SEF
7:INEG
8:ABEG
9:INEF
10:ABEF
11:CHINESE
12:TAIPEI
13:SEEG2
Content
Japan
SEC
SECL
SEEG
SUK
SCA
SEF
EX inch series
EX AB series
EX inch series (FC)
EX AB series (FC)
China
Taiwan
SEEG2
Setting
range
0-13
Default
0
26-10
Function
(Purpose)
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the NETWORK soft key and press the [OK]
key, and the collating result is displayed with OK or NG.
When "0" is entered to the soft key, it is treated as a trial setup.
(Initial screen)
(In case of OK)
(In case of NG)
Sim26-10 SCANNERKEY
SCANNER KEY ON
-------------------
AR-235/275 SIMULATION - 20
Sim26-10 SCANNERKEY
SCANNER KEY OK
-------------------
Sim26-10 SCANNERKEY
SCANNER KEY NG
----------
26-20
Used to set the job separator paper exit mode.
Function
(Purpose)
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
26-12
Function
(Purpose)
Operation/procedure
[ 0- 1]
Display
items
0:OFF
1:ON
Content
Paper is discharged to No. 1
paper exit port.
Used to discharge paper to the
job separator tray (No. 2 paper
exit port).
Setting
range
0-1
Default
0
Purpose
Function
(Purpose)
Item
26-22
Setting
Used to set the specification (language display) for the
destination.
Specifications
Operation/procedure (Pattern 1)
Select the language to be used according to the table below.
Operation/procedure
Setting
Used to set enable/disable of toner save operation.
Specifications
Sim26-22 LANGUAGE
LANGUAGE
0
(0:JAPANESE
1:ENG.US 2:ENG.UK
1/3 [ 0- 19]
0
Display items
0:JAPANESE
1:ENG.US
2:ENG.UK
3:FRENCH
4:GERMAN
5:ITALY
6:DUTCH
7:SWEDISH
8:SPANISH
9:PORTUGUESE
10:TURKISH
11:GREEK
12:POLISH
13:HUNGARIAN
14:CZECHOSLOVAK
15:RUSSIAN
16:FINNISH
17:NORWEGIAN
18:DANISH
19:CHINESE
Setting
range
0-19
Default
0
Operation/procedure (Pattern 1)
26-30
Input the set value with the 10-key and press the [OK] key.
Purpose
Function
(Purpose)
Item
Setting
Used to set the operation mode for CE mark.
Specifications
Operation/procedure (Pattern 1)
[ 0- 1]
Display
items
0:OFF
1:ON
Input the set value with the 10-key and press the [OK] key.
Content
Disable
Enable
Setting
range
0-1
Sim26-30 CE MARK
CE MARK CONTROL 0
(0:OFF 1:ON)
[ 0- 1]
Note
AR-235/275 SIMULATION - 21
Display items
Setting range
0-1
0:OFF
1:ON
Default
Japan, SEC, SECL,
SCA, SEF, Taiwan
0
26-38
Others
1
26-35
Setting
Purpose
Used to set whether to stop when the drum life is
Function
(Purpose) reached.
Operation
Item
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Setup
Purpose
Used to set the mode of trouble memory.
Function
(Purpose)
Specifications
Item
Operation/procedure (Pattern 1)
Display item
0:ONCE
Purpose
Function
(Purpose)
Set range
0-1
Default
0
Operation/procedure (Pattern 1)
[ 0- 1]
Display items
0:OFF
1:ON
Content
Setting No
Setting Yes
Sim26-36 MAINTESTOP
MAINTENANCE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1]
0
Setting range
0-1
Purpose
Function
(Purpose)
Item
Default
1
Setting
Used to set whether to use the black/white reverse
function.
Operation
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Sim26-50 B/W REV.
B/W REVERSE
0
(0:ON 1:OFF)
26-37
Setting
Used to set whether to stop when the developer life is
reached.
Operation
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Sim26-37 DEVE. STOP
DEVE. LIFE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1]
0
Display items
0:STOP
1:NON STOP
Content
Stop
Non stop
Default
0
26-50
Purpose
Function
(Purpose)
Item
Setting range
0-1
Input the set value with the 10-key and press the [OK] key.
Content
Stop
Non stop
Item
Setting
Used to set whether to meet with the output direction of
images regardless of the mode when installing the
finisher.
Operation
Input the set value with the 10-key and press the [OK] key.
Setting
Used to set whether to stop when the maintenance life
is reached.
Operation
Display items
0:STOP
1:NON STOP
Default
0
Operation/procedure (Pattern 1)
26-36
Purpose
Function
(Purpose)
Item
Setting range
0-1
26-46
Content
When two or more troubles
occur, only one is registered.
All the troubles occurred are
registered.
1:ANY
Content
Stop
Non stop
Sim26-35 TROUBLE
TROUBLE MODE
0
(0:ONCE 1:ANY)
[ 0- 1]
Display items
0:STOP
1:NON STOP
[ 0- 1]
Display
items
0:ON
1:OFF
Content
Enable
Disable
Setting
range
0-1
Default
0
26-54
Purpose
Function
(Purpose)
Item
Setting
Used to set the PWM duty (brightness) at the center
value of the LCD contrast.
Operation
Operation/procedure (Pattern 1)
Setting range
0-1
Default
0
Input the set value with the 10-key and press the [OK] key, and the
LCD contrast will be immediately changed and displayed.
Sim26-54 LCD DUTY
LCD PWM DUTY
0
Setting range
Default
AR-235/275 SIMULATION - 22
30-70
50
Operation/procedure (Pattern 1)
26-57
Input the set value with the 10-key and press the [OK] key.
Setting
Purpose
Used to set the model code.
Function
(Purpose)
Operation
Item
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Display
items
0:OFF
Sim26-57 MACHINE
MACHINE CODE
1
(1:AR-235
2:AR-255S
1/5 [ 1-10]
1
Content
In case of the communication
trouble, U7-00 is not displayed.
In case of the communication
trouble, U7-00 is displayed.
1:ON
Display items
Setting range
1-10
1:AR-235
2:AR-255S
3:AR-255P
4:AR-255F
5:AR-255FP
6:AR-275
7:AR-N275
8:DM-2305
9:DM-2515
Default
1
Purpose
Function
(Purpose)
Item
Setting
Used to enter the TAG No. of the copier.
Data
Operation/procedure
Current memory is displayed in PRESENT column.
Enter a value (max. 8 digits) with the 10-key, and press the [OK] key.
The input number is displayed instead of "NEW".
Item
Default
27-5
10:DM-2705
Purpose
Function
(Purpose)
Setting
range
0-1
Setting
Used to set enable/disable of the FAX mode key when
FAX is not installed. (When FAX is installed, the FAX
mode is enabled regardless of this setup.)
Operation
Operation/procedure (Pattern 1)
30
Input the set value with the 10-key and press the [OK] key.
This setup varies in connection with SIM 26-6 (Destination setup).
Purpose
Function
(Purpose)
Display
items
0:ON
1:OFF
30-1
Content
Effective (The
message with FAX
uninstalled is
displayed.)
Disable (Error Beep)
Setting
range
0-1
Default
JAPAN,
SEC, SECL, Others
SUK, SCA
0
1
Section
Item
Operation test/check
Used to check the operation of sensors and detectors
in the sections other than the paper feed section of the
copier and the related circuit. (The operation of
sensors and detectors can be monitored with the
LCD.)
Others
Operation
Operation/procedure
The operating conditions of sensors and detectors in the different sections than the paper feed section of the machine are displayed. The
active sensors and detectors are highlighted.
Sim30-1 MAIN SENSOR
PPD1H PPD1L PPD2
POD1 DVCH DRST
DSWR1 SFTHP POD2
TOPF DSWR0 LOEMP
27
27-1
Purpose
Function
(Purpose)
Section
Item
Setting
Used to set PC/MODEM communication trouble (U700) detection Yes/No.
Communication (RIC/MODEM)
Specifications
Operation mode
(Common)
PPD1H
PPD1L
PPD2
POD1
DVCH
DRST
DSWR1
SFTHP
POD2
TOPF
DSWR0
LOEMP
AR-235/275 SIMULATION - 23
40-2
30-2
Operation test/check
Used to check the operation of sensors and detectors
in the paper feed section and the related circuits. (The
operations of sensors and detectors in the paper feed
section can be monitored with the LCD.)
Paper feed
Section
Operation
Item
Operation/procedure
Purpose
Function
(Purpose)
Adjustment
Purpose
Used to adjust the manual paper feed tray paper width
Function
(Purpose) detector detection level.
Paper feed
Section
Operation
Item
Operation/procedure
1) Set A3/W Letter and fit the guide, then press the [OK] key.
2) Set A4R/LetterR and fit the guide, then press the [OK] key.
When the intermediate position adjustment is not performed, press
the [OK] key without changing the guide position.
3) Set to A5R/INVOICE R and fit the guide, then press the [OK] key.
When the intermediate position adjustment is not performed, press
the [OK] key without changing the guide position.
4) Narrow the guide at minimum, press the [OK] key.
5) Set the paper detection width (+), and press the [OK] key.
6) Set the paper detection width (), and press the [OK] key.
PED1
LUD1
CD1
PED2
LUD2
CD2
PFD2
DSWR2
MPED
MPLS1
MPLS2
MPLD1
MPLD2
If "FAILED" is displayed in procedure 1), 2), 3), or 4), it is NG of adjustment. Repeat the adjustment.
(Maximum position setting
screen: AB series)
Sim40-2 MB SENSOR
A3 PAPER SET
Sim40-2 MB SENSOR
WLT PAPER SET
PRESS OK KEY
PRESS OK KEY
Sim40-2 MB SENSOR
LTR PAPER SET
PRESS OK KEY
PRESS OK KEY
Width detection size of the manual feed tray (one of them is displayed.)
A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA
(At detection, highlighted)
If the intermediate position adjustment is not performed, press the
[OK] key without changing the guide position.
40
40-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the manual paper feed
tray paper size detector and the related circuit. (The
operation of the manual paper feed tray paper size
detector can be monitored with the LCD.)
Paper feed
Operation
Operation/procedure
The status of sensors and detectors in the manual paper feed section
is displayed. The active sensors and detectors are highlighted.
Sim40-2 MB SENSOR
A5R PAPER SET
Sim40-2 MB SENSOR
INVR PAPER SET
PRESS OK KEY
PRESS OK KEY
Sim40-1 MB SENSOR
MPLS1 MPLS2 MPLD1
MPLD2 A3/A4 INV/LTR
B5/B4 LT/WLT A5/A4R
B5R POSTCARD EXTRA
MPLS1
MPLS2
MPLD1
MPLD2
Sim40-2 MB
PAPER +
MID-L ADJ.
MID-S ADJ.
[ 1-
SENSOR
60
ON
ON
99]
60
Width detection size of the manual feed tray (one of them is displayed.)
A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA
AR-235/275 SIMULATION - 24
Sim40-2 MB SENSOR
PAPER +
60
PAPER 40
COMPLETE
LON SON
(Executing screen)
(Initial screen)
Sim41-2 PD SENSOR
PRESS OK KEY
EXEC
OCSW
40-3
Adjustment
Purpose
The AD conversion value of manual feed width
Function
(Purpose) detection is displayed.
Paper feed
Section
Operation
Item
Operation/procedure
The AD conversion value of manual feed width detection is displayed.
41-3
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the light reception level and the
detection level of the original size detection photo
sensor.
Others
Operation
Operation/procedure
Sim40-3 MB SENSOR
AD CONVERT VALUE
[123]
41
OCSW
41-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the document size detection photo
sensor.
Others
Operation
Operation/procedure
The operation status of the sensors and detectors in the original size
detection section are displayed. The active sensors and detectors are
highlighted.
Sim41-1 PD SENSOR
OCSW PD1 PD2
PD3 PD4 PD5
1 to 5
PD sensor detection
level
Adjustment
Used to adjust the detection level of OC 20 degrees.
Others
Operation
Operation/procedure
Set the OC cover at 20 degrees detection and press the [OK] key.
(Initial screen)
OCSW
PD1 to 5
Purpose
Function
(Purpose)
Section
Item
Sim41-4 20 SENSOR
41-2
Adjustment
Used to adjust the detection level of the document size
photo sensor.
Others
Operation
Operation/procedure
(Executing screen)
1 to 5
PD sensor
detection level
AR-235/275 SIMULATION - 25
43
Display items
Content
ENVIRONMENT ADJ.
Environmental correction
Valid/Invalid
(0: Environmental
correction invalid
1: Environmental
correction valid)
43-1
Setting
Purpose
Used to set the fusing temperature in each operation
Function
(Purpose) mode.
Fixing (Fusing)
Section
Operation
Item
Operation/procedure (Pattern 2)
After the mode selection, enter the adjustment value and press the
[OK] key.
(Initial screen)
(Input screen)
Sim43-1 FUSER TEMP.
1:600dpi
185
2:1200dpi
160
3:POST CARD
185
2
Display items
1:600dpi
2:1200dpi
3:POST CARD
Setting range
155-190
140-190
155-190
44-34
Adjustment
Purpose
Used to adjust the transfer current value.
Function
(Purpose)
Operation/procedure
When changing +V2, check with +V1 unchanged. If there is any trouble
in the half tone image of graphics, keep the relationship between +V1
and +V2 at the default and change it.
Default
185
160
185
When the image quality is deteriorated because the user selects the
OHP mode and use other than the recommended OHP, decrease the
transfer current to adjust deterioration of black background picture
quality. If some of characters are not printed, increase the transfer current.
43-10
Purpose
Function
(Purpose)
Section
Item
Default
[140-190] 160
Content
600dpi
1200dpi
Postcard
Setting
range
0-1
Setting
Used to set the paper feed cycle for postcard.
Paper feed
Operation
Operation/procedure (Pattern 1)
(Initial screen)
Sim44-34
1:+V1
2:+V2 F
3:+V2 R
1/4
(Input/Executing screen)
TC ADJ.
(600) 20
(600) 20
(600) 18
Sim44-34 TC ADJ.
4:+V2 S-F(600) 22
[ 5- 30]
22
Input the set value with the 10-key and press the [OK] key.
Sim43-10 POST CARD
PICK UP CYCLE
50
[ 1- 99]
Setting range
Default
Display items
1-99
50
44
44-1
Purpose
Function
(Purpose)
Section
Item
Setting
Used to make various setups in each mode of process
control.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Operation
Operation/procedure (Pattern 1)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Sim44-1 PROCON MODE
ENVIRONMENT ADJ. 1
[ 0- 1]
600dpi +V1
600dpi +V2 front
surface
3:+V2 R (600)
600dpi +V2 back
surface
4:+V2 S-F(600)
600dpi +V2 small
size front
5:+V2 S-R(600)
600dpi +V2 small
size back
6:+V2 OHP(600)
600dpi +V2OHP
7:+V1 (1200)
1200dpi +V1
8:+V2 F (1200)
1200dpi +V2 front
surface
9:+V2 R (1200)
1200dpi +V2 back
surface
10:+V2 S-F(1200) 1200dpi +V2 small
size front
11:+V2 S-R(1200) 1200dpi +V2 small
size back
12:+V2 OHP(1200) 1200dpi +V2OHP
1:+V1 (600)
2:+V2 F (600)
50
Content
Setting
range
5-30
5-30
Default
Japan,
Others
USA
18
20
18
20
5-30
16
16
5-30
24
24
5-30
18
18
5-30
5-30
5-30
20
8
12
20
8
14
5-30
5-30
14
14
5-30
12
12
5-30
10
10
44-35
Purpose
Function
(Purpose)
Setting
Correction temperature setup when correcting the
ambient temperature.
Operation/procedure
Correction is performed when the temperature sensor installed to the
MCU indicates 15C or below.
The content of correction is to raise the DVB-Bias and Grid by 50V.
The simulation allows to vary the correction threshold value in the
range of 0 to 20C.
AR-235/275 SIMULATION - 26
If, however, the set temperature is increased, correction at a high voltage is performed in normal temperatures.
Sim44-35 ENV.ADJ.
DVB/GRID ENV TMP 15
[ 0- 20]
Setting range
Default
0-20
15C
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-7 SUPER PHOTO
1:
1.0(SHIFT) 50
2:
1.0(GAMMA) 50
3:
2.0(SHIFT) 50
1/4
50
15
44-40
Display items
Purpose
Function
(Purpose)
Setting
Used to set the rotating time before toner supply.
Operation/procedure (Pattern 1)
Enter the set value with the 10-key, and the set value will be registered.
Sim44-40 TONER
ROTATE TIME
50
[ 1- 99]
Setting range
Default
1-99
8
1:1.0(SHIFT)
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
10:5.0(GAMMA)
Content
Super photo level 1.0 (shift qty)
Super photo level 1.0 (slant)
Super photo level 2.0 (shift qty)
Super photo level 2.0 (slant)
Super photo level 3.0 (shift qty)
Super photo level 3.0 (slant)
Super photo level 4.0 (shift qty)
Super photo level 4.0 (slant)
Super photo level 5.0 (shift qty)
Super photo level 5.0 (slant)
Setting
Default
range
1-99
32
1-99
50
1-99
41
1-99
50
1-99
50
1-99
50
1-99
56
1-99
61
1-99
62
1-99
66
46
46-9
46-2
Purpose
Function
(Purpose)
Item
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the copy exposure level.
Picture quality
Density
Operation/procedure (Pattern 5)
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
(Auto adjustment)
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:AE(TS)
7:TEXT(TS)
8:TEXT/PHOTO(TS)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-9 TEXT
1:
1.0(SHIFT)
2:
1.0(GAMMA)
3:
2.0(SHIFT)
1/7
Display items
Adjustment
Used to adjust individually the copy exposure level.
(Character)
Picture quality
Density
50
50
50
50
Display items
Setting
range
1-99
Content
AE
Character
Character/Photo
Photo
Super photo
AE (TS)
Character (TS)
Character/Photo (TS)
Default
1:1.0(SHIFT)
50
Level 3.0
Level 3.0
Level 3.0
Level 3.0
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
Level 3.0
Level 3.0
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
46-7
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust individually the copy exposure level.
(Super photo)
Picture quality
Density
10:5.0(GAMMA)
11:TS 1.0(SHIFT)
12:TS 1.0(GAMMA)
Operation/procedure (Pattern 5)
13:TS 2.0(SHIFT)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
14:TS 2.0(GAMMA)
AR-235/275 SIMULATION - 27
Content
Character level 1.0 (shift
qty)
Character level 1.0 (slant)
Character level 2.0 (shift
qty)
Character level 2.0 (slant)
Character level 3.0 (shift
qty)
Character level 3.0 (slant)
Character level 4.0 (shift
qty)
Character level 4.0 (slant)
Character level 5.0 (shift
qty)
Character level 5.0 (slant)
Character (TS) level 1.0
(shift qty)
Character (TS) level 1.0
(slant)
Character (TS) level 2.0
(shift qty)
Character (TS) level 2.0
(slant)
Setting
range
1-99
Default
22
1-99
1-99
44
36
1-99
1-99
47
50
1-99
1-99
50
61
1-99
1-99
55
72
1-99
1-99
60
22
1-99
44
1-99
36
1-99
47
Display items
Content
Setting
range
1-99
Default
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
46-10
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust individually the copy exposure level.
(Character/Photo)
Picture quality
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-10 TEXT/PHOTO
1:
1.0(SHIFT) 50
2:
1.0(GAMMA) 50
3:
2.0(SHIFT) 50
1/7
50
Display items
Content
Display items
1:1.0(SHIFT)
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
10:5.0(GAMMA)
11:TS 1.0(SHIFT)
12:TS 1.0(GAMMA)
13:TS 2.0(SHIFT)
14:TS 2.0(GAMMA)
15:TS 3.0(SHIFT)
Content
Character/Photo level 1.0
(shift qty)
Character/Photo level 1.0
(slant)
Character/Photo level 2.0
(shift qty)
Character/Photo level 2.0
(slant)
Character/Photo level 3.0
(shift qty)
Character/Photo level 3.0
(slant)
Character/Photo level 4.0
(shift qty)
Character/Photo level 4.0
(slant)
Character/Photo level 5.0
(shift qty)
Character/Photo level 5.0
(slant)
Character/Photo (TS)
level 1.0 (shift qty)
Character/Photo (TS)
level 1.0 (slant)
Character/Photo (TS)
level 2.0 (shift qty)
Character/Photo (TS)
level 2.0 (slant)
Character/Photo (TS)
level 3.0 (shift qty)
Default
30
1-99
37
1-99
40
1-99
43
1-99
50
1-99
50
1-99
57
1-99
61
1-99
64
1-99
66
1-99
30
1-99
37
1-99
40
1-99
43
1-99
50
Default
Character/Photo (TS)
50
level 3.0 (slant)
17:TS 4.0(SHIFT) Character/Photo (TS)
1-99
57
level 4.0 (shift qty)
18:TS 4.0(GAMMA) Character/Photo (TS)
1-99
61
level 4.0 (slant)
19:TS 5.0(SHIFT) Character/Photo (TS)
1-99
64
level 5.0 (shift qty)
20:TS 5.0(GAMMA) Character/Photo (TS)
1-99
66
level 5.0 (slant)
Setup of various copy conditions: Similar to the normal copy mode.
16:TS 3.0(GAMMA)
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
46-11
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust individually the copy exposure level.
(Photo)
Picture quality
Density
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-11 PHOTO
1:
1.0(SHIFT)
2:
1.0(GAMMA)
3:
2.0(SHIFT)
1/4
50
50
50
50
Display items
Setting
range
1-99
Setting
range
1-99
Content
1:1.0(SHIFT)
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
10:5.0(GAMMA)
Setting
range
1-99
Default
32
50
41
50
50
50
56
61
62
66
Adjustment
FAX exposure level adjustment (batch)
Operation/procedure
Shading is performed to turn on the copy LED.
The current exposure value of "Normal character, Auto exposure"
mode is displayed.
Enter an adjustment value of 2 digits with the 10-key and press the
START key, and the entered value will be set to all the modes and the
self print will be made in the normal size.
Exposure adjustment value table
AR-235/275 SIMULATION - 28
Mode
AE
Photo
Exposure adjustment
ON
STD
(Standard
character)
Auto
Manual
Auto
Manual
Fine
Auto
(Small
Manual
character)
Auto
Manual
S-fine
Auto
(Fine)
Manual
Auto
Manual
U-fine
Auto
(Super fine)
Manual
Auto
Manual
When initializing each data: 50
Display items
OFF
ON
OFF
ON
Individual adjustment
enable
(46-13 to 16)
Character
Level 3.0
Character/Photo
Level 3.0
Photo
Level 3.0
Super photo
Level 3.0
Default
50
AE(TS)
Character (TS)
Level 3.0
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
OFF
46-19
Purpose
Function
(Purpose)
Item
Adjustment
FAX exposure level adjustment (individual)
The FAX exposure level can be adjusted separately for each mode by
specifying a sub code. Since selection of Auto/Manual and Photo ON/
OFF is allowed separately for each mode, adjustments of 14 patterns
in total can be made.
(Refer to 46-12, "Exposure adjustment table".)
Adjustment
Used to change the image quality in the exposure
mode.
Picture quality
Operation/procedure (Pattern 2)
Select the mode with the 10-key and press the [OK] key.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
Auto exposure mode
When SIM 26-6 (Destination setup) is changed from EX to Japan,
the setup value becomes 1 (Default: Japan). If, on the contrary, it is
changed from Japan to EX, the set value becomes 2 (Default: EX)
If the auto exposure mode setup value is changed, the setup value
of SIM 46-30 (AE limit setup) is reset to the default value.
(Initial screen)
(Input screen)
Mode
STD (normal character)
Fine (small character)
S-fine (super fine)
U-fine (super fine)
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-18 GAMMA SET.
1:AE
50
2:TEXT
50
3:TEXT/PHOTO
50
1/3
50
AE
ON
Operation/procedure
Purpose
Function
(Purpose)
Item
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:AE(TS)
7:TEXT(TS)
8:TEXT/PHOTO(TS)
46-13 to 16
Sub code
13
14
15
16
Setting
range
1-99
Content
OFF
Purpose
Function
(Purpose)
(Auto adjustment)
Sim46-19 AE MODE
1:AE MODE
2:AE STOP(COPY)
3:AE STOP(FAX)
1/2
1
0
0
1
Display items
1:AE MODE
(1:EXPOSURE
2:TONER)
2:AE STOP(COPY)
(0:FIXED
1:REAL TIME)
3:AE STOP(FAX)
(0:FIXED
1:REAL TIME)
4:AE STOP(SCAN)
(0:FIXED
1:REAL TIME)
5:1200dpi PHOTO
(1:SOFT
2:HARD)
Sim46-19 AE MODE
1:AE MODE
1
(1:EXPOSURE
2:TONER)
[ 1- 2]
1
Content
Auto exposure mode
(1: Priority on Image quality,
2: Priority on toner consumption)
Auto exposure STOP mode (COPY)
(0: Fixed, 1: Real-time)
Default
2
46-20
Purpose
Function
(Purpose)
Item
Adjustment
Used to correct SPF exprosure.
Picture quality
Operation/procedure (Pattern 2)
Select the mode with the 10-key and press the [OK] key.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
AR-235/275 SIMULATION - 29
(Initial screen)
(Input screen)
Display items
1:SPF EXPOSURE
2:RSPF EXPOSURE
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
[ 1- 99]
Content
SPF
RSPF
48-2
50
Setting range
1-99
Purpose
Function
(Purpose)
Section
Item
Default
50
Adjustment
Used to adjust the scanner mode magnification ratio
(main/sub scanning direction).
Image processing
Picture quality
46-30
Operation/procedure (Pattern 5)
Setting
Purpose
Used to set the AE limit.
Function
(Purpose)
Operation/procedure (Pattern 2)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
Select the mode with the 10-key and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
If SIM 26-6 (Destination setup) and SIM46-19 (Auto exposure mode)
are changed, this setup is also changed to the default value accordingly.
(Initial screen)
(Input screen)
Sim46-30 AE LIMITTE
1:AE
0
2:AE(TS)
0
1
Display items
1:AE
2:AE(TS)
Setting range
0-31
1:F-R
2:SCAN
Default
0
(Executing screen)
MAG
50
50
50
50
Display items
Sim46-30 AE LIMITTE
1:AE
0
[ 0- 31]
Sim48-2 SCANNER
1:F-R
2:SCAN
3:SPF(SIDE1)
1/2
3:SPF(SIDE1)
4:SPF(SIDE2)
Content
Main scanning magnification
ratio adjustment
Sub scanning magnification
ratio adjustment
SPF surface sub scan
magnification ratio
SPF back surface sub scan
magnification ratio
Setting
range
1-99
Default
50
48
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
48-1
Purpose
Function
(Purpose)
Section
Item
Adjustment
Used to adjust the copy mode magnification ratio (main
scanning direction, sub scanning direction).
Image processing
Picture quality
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim48-1 COPY MAG.
1:F-R(AUTO)
50
2:F-R
50
3:SCAN
50
1/2
50
1:F-R(AUTO)
4:SPF(SIDE1)
5:SPF(SIDE2)
6:DUPLEX
Adjustment
Used to adjust the lead edge/sub scan magnification
ratio automatically.
Operation
Open the OC cover, and put the lead edge/sub scan automatic adjustment chart on the OC. (Keep the OC cover open.)
Place the chart correctly on the OC reference position. (If not, a correct
adjustment cannot be made.)
If the adjustment is normally completed, the adjusted value is displayed and written into the EEPROM. In case of an abnormality, "ERR"
is displayed and the value is not written into the EEPROM.
Content
3:SCAN
Purpose
Function
(Purpose)
Item
Display items
2:F-R
48-3
Setting
range
Default
50
60
50
EXEC
Sim48-3 READ
RRC-A
OC Center
MirSpeed
PRESS OK KEY
AR-235/275 SIMULATION - 30
AUTO
[ 32]
[ 53]
[ 58]
EXEC
AUTO
[ ERR]
[ ERR]
[ ---]
EXEC
48-8
Display items
Adjustment
Purpose
FAX magnification ratio adjustment (read)
Function
(Purpose)
Related soft SW76-1 to 8, SW77-1 to 8
SW
Operation/procedure
Adjustment
range
Adjustment
unit
1 128
255%
0.1%
increment
Adjustment
FAX magnification ratio adjustment (print)
Setting
range
1-99
Default
Adjust and set FAX document read magnification ratio, read and print
the document.
Adjustment magnification ratio
Content
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
SW78-1 to 8, SW79-1 to 8
Operation/procedure
After the adjustment/setting of FAX print magnification ratio, read and
print the document.
Adjustment magnification ratio
Main scanning magnification ratio
Sub scanning magnification ratio
Adjustment
range
1 128
255%
Adjustment
unit
0.1%
increment
50-5
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the print image position (top margin) on
the print paper in the print mode.
Picture quality
Print area
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
48-10
Purpose
Function
(Purpose)
Related soft SW
Adjustment
FAX auto reduction magnification ratio (print).
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-5 PRINT EDGE
1:TRAY1
50
2:OPTION
50
3:MANUAL
50
1/2
50
SW25-1 to 4
Operation/procedure
Set the FAX auto reduction magnification ratio (0 to 15%).
Note: Executable only when the FAX is installed.
Display
items
1:TRAY1
2:OPTION
3:MANUAL
4:DUPLEX
50
50-1
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the copy lead edge position.
Picture quality
1st cassette
Option cassette
Manual feed
Back print
Setting range
Default
0-99
1-99
53
Image position
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-1 LEAD EDGE
1:RRC-A
43
2:RRC-B
18
3:RRC-MANUAL
18
1/4 [ 1- 99] 43
Content
50-6
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the print image position (top margin) on
print paper in the copy mode. (SPF/RSPF)
Picture quality
Image position
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
AR-235/275 SIMULATION - 31
(Initial screen)
(Input screen)
(Executing screen)
Adjustment
Purpose
FAX lead edge adjustment (print)
Function
(Purpose)
Related soft SW SW74-1 to 4, SW75-5 to 8
Operation/procedure
Display items
Setting
range
1-99
Content
Default
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
50-8
The adjustments on the machine side must have been normally
completed.
Purpose
Function
(Purpose)
Related soft SW
50-9
Adjustment
FAX lead edge adjustment (read)
SW44-5 to 8, SW45-5 to 8
Operation/procedure
Adjust and set FAX document read lead edge position, read and print
the document.
OC read
SPF read
E
A
B
After the adjustment/setting of FAX print lead edge position, read and
print the document.
Adjustment position
A
B
Adjustment range
43 50 57
43 50 57
Adjustment
unit
16 lines
16 dots
Purpose
Function
(Purpose)
Section
Item
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-10 PRT.CENTER
1:BYPASS
50
2:TRAY1
50
3:TRAY2
50
1/2
50
Display items
1:BYPASS
2:TRAY1
3:TRAY2
4:TRAY3
5:TRAY4
6:DUPLEX
Content
Manual feed
1st cassette
2nd cassette
3rd cassette
4th cassette
Back print
Setting range
1-99
Default
50
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
Read area
50-12
Read area
A
B
C
D
E
F
G
H
Adjustment position
Adjustment range
43 50 57 lines
43 50 57 lines
43 50 57 lines
43 50 57 lines
43 50 57 lines
43 50 57 lines
43 50 57 lines
43 50 57 lines
Adjustment
unit
8 lines
8 dots
8 lines
8 dots
8 lines
8 dots
8 lines
8 dots
Purpose
Function
(Purpose)
Section
Item
Adjustment
Used to adjust the print image center position.
(Adjustment can be made for each document mode.)
Image processing
Picture quality
Image position
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-12 ORG.CENTER
1:OC
50
2:SPF(SIDE1)
50
3:SPF(SIDE2)
50
50
AR-235/275 SIMULATION - 32
Display items
Content
Setting range
Default
1:OC
OC
1-99
50
2:SPF(SIDE1) SPF front surface
3:SPF(SIDE2) SPF back surface
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
51-1
Item
Setting
Used to set to disable the operation of the separation
pawl of the photoconductor drum.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Operation
Item
Operation/procedure (Pattern 1)
Purpose
Function
(Purpose)
Section
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
51
Purpose
Function
(Purpose)
Section
51-8
Adjustment
Used to adjust the OPC drum separation pawl ON
time.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Operation
Display items
0:ON
1:OFF
Content
Setting range
0-1
Enable
Disable
Default
0
Operation/procedure (Pattern 2)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
(Initial screen)
(Input screen)
Sim51-1 D/F TIMING
1:600dpi
50
2:1200dpi
50
2
Display items
1:600dpi
2:1200dpi
[ 1- 99]
Setting range
1-99
61
61-1
Purpose
Function
(Purpose)
Section
Item
50
Default
50
Operation test/check
Used to test the operation of the LSU.
LSU
Operation
Operation/procedure
Pressing the [OK] key performs the LSU test.
51-2
Purpose
Function
(Purpose)
Section
Item
Adjustment
Used to adjust the contact pressure of paper onto the
resist roller in each section (copier paper feed section,
duplex paper feed section, SPF paper feed section).
(When the print image position varies greatly for the
paper or when a lot of paper jam troubles occur, the
adjustment is required.)
Paper transport (Discharge/Switchback/Transport)
Operation
Used to set the LSU to ON state and check that the sync signal
(HSYNC/) is outputted or not.
After operation for 30 sec, the result is displayed. (Interruption cannot
be made for 5 sec after starting the operation.)
(Initial screen)
(Executing screen)
PRESS OK KEY
Interruption is inhibited
during execution.
During execution,
[EXEC] is highlighted.
EXEC
EXEC
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim51-2 RESIST ADJ.
1:BYPASS
50
2:TRAY1
50
3:TRAY2
50
1/3
50
COMPLETE
ERROR
EXEC
EXEC
63
63-1
Display items
1:BYPASS
2:TRAY1
3:TRAY2
4:TRAY3
5:TRAY4
6:DUPLEX
7:SPF(SIDE1)
8:SPF(SIDE2)
Content
Manual feed
1st cassette
2nd cassette
3rd cassette
4th cassette
Back print
SPF front surface
SPF back surface
Setting range
1-99
Default
50
Purpose
Function
(Purpose)
Section
Item
Operation/procedure
Pressing the [OK] key performs shading, and displays the result (center pixel).
(Initial screen)
(Executing screen)
Sim63-1 SHADING
Sim63-1 SHADING
Sim63-1 SHADING
PRESS OK KEY
EXEC
EXEC
PRESS OK KEY
EXEC
65
65-5
40
63-7
Adjustment
Used to adjust the SPF white correction start pixel
position automatically.
This adjustment is performed after the lens unit is
replaced.
Scanner
Section
Operation
Item
Operation/procedure
Purpose
Function
(Purpose)
COMPLETE
Set the SPF unit OPEN, and press the [OK] key.
[ ] indicates the order number of the pixel of the white sheet for SPF
exposure correction in the SPF position.
If the adjustment is normally completed, "COMPLETE" is displayed
and data are written into the EEPROM.
In case of an abnormality, "ERROR" is displayed and no data is written
into the EEPROM.
The SPF white correction start pixel = Displayed pixel position - 34
If the simulation is executed with the SPF unit closed, an error is
resulted.
(Initial screen)
(Executing screen)
Interruption is inhibited
Sim63-7 SPF ADJ.
Sim63-7 SPF ADJ.
during execution.
WHITE ADJUST
WHITE ADJUST
During execution,
[EXEC] is highlighted.
EXEC
PRESS OK KEY
66
66-1
Purpose
Function
(Purpose)
Adjustment/Setting/Check
FAX related soft SW setting
Operation/procedure
Display FAX software SW on LCD, and set/change those with 10-key.
Note: Executable only when the FAX is installed.
66-2
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Initial set for the value of the FAX soft SW
Operation/procedure
Sim63-7 SPF ADJ.
WHITE ADJUST
COMPLETE
[160]
PRESS OK KEY EXEC
Used to clear the FAX-related soft switches except for the line signal
adjustment value and the machine adjustment value and to set default
values (which differ depending on the country code separately
entered.)
Note: Executable only when the FAX is installed.
66-3
64
Purpose
Function
(Purpose)
64-1
Purpose
Function
(Purpose)
Section
Item
Adjustment/Setting/Check
FAX PWB memory check
Operation/procedure
Operation test/check
Used to check the operation of the printer function
(auto print operation).
Printer
Operation
Operation/procedure
Pressing the [START] key makes a print by 2 by 4 mode. After completion of printing, the menu returns to the initial menu.
Pressing the [CA] key cancels the simulation mode.
(Input screen)
(Executing screen)
Program area
Memory area
Option memory
PAGE
2. Detailed procedure
1
AR-235/275 SIMULATION - 34
Adjustment/Setting/Check
Purpose
Print the screen memory contents
Function
(Purpose)
Operation/procedure
Used to input all image data (including confidential reception data,
remote send image, not-sent image) stored in image memory of the
FAX section.
The output image is remained even after outputting.
Note: Executable only when the FAX is installed.
66-8
66-4
Purpose
Function
(Purpose)
Related soft
SW
66-7
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Signal send mode
Operation/procedure
By setting the message No., the sound message is sent to the line and
the speaker of the body. (The message is repeated until the interruption command is provided by pressing the [BACK] key.)
Operation/procedure
By setting the message No., the signal is sent to the line and the
speaker of the body. (The signal is continuously sent until the interruption command is provided by pressing the [BACK] key.)
Message
number
1
The signal send level can be selected from 0dB or the soft SW set
value. However, the level setup is not required for 01, 31 - 35, the
selection may does not appear. After completion of the mode, the signal send level is returned to the soft SW set value before execution of
the mode.
Signal
number
01
26
27 to 30
31
32
33
34
35
Other than
the above
Send signal
Signal not send
7EH Flag signal
Tone signal
Pseudo-ringer sound
([ON HOOK] key ON)
Voice message (no sound)
Under the state where the ring back
tone can be sent to the line, keep
the sound composition IC volume to
0.
Ring back tone (no sound)
Under the state where the ring back
tone can be sent to the line, keep
the G/A volume to 0.
Dial pulse (make)
Maintain the make state with
keeping the condition to be able to
send to the dial pulse line.
Dial pulse (break)
Maintain the break state with
keeping the condition to be able to
send to the dial pulse line.
FFH
Send level
Selection menu
None
Yes
Yes
None
None
2
3
4
Voice message
"Hold the line a minute, please send fax."
(TEL/FAX voice response)
"Hold the line a minute."
(TEL/FAX voice response)
"Not around here, please send fax."
(TEL/FAX voice response)
"Ding Dong"
(Sound delivered when switching to remote reception)
Adjustment/Setting/Check
Image data memory clear
Operation/procedure
Used to clear all image data (including confidential reception data)
stored in image memory of the FAX section.
None
1: 0dB
2: Soft SW
1: 0dB
2: Soft SW
Yes
66-11
Purpose
Function
(Purpose)
Adjustment/Setting/Check
300bps signals send
Operation/procedure
By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [BACK] key.)
The signal send level can be selected from 0dB or the soft SW set
value.
The signal send level is returned to the soft SW set value before execution of the mode after completion of the mode.
66-6
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Voice Message send
Number
1
2
3
Adjustment/Setting/Check
Printing the confidential password
Signal
No signal (CML ON)
11111
11110
Number
4
5
6
Operation/procedure
The confidential ID table (confidential BOX numbers, confidential BOX
names, and confidential password) is printed.
The confidential data of My company mode is printed separately.
Note: Executable only when the FAX is installed.
AR-235/275 SIMULATION - 35
Signal
00000
010101
00001
66-13
Adjustment/Setting/Check
Send test and adjustment of the dial pulse and
DTMF signal.
SW53-1 to 4 (DTMF high group end level)
SW53-5 to 8 (DTMF low group send level)
SW67-1 to 4 (DP 10PPS make time)
SW67-5 to 8 (DP 10PPS make time)
Operation/procedure
Purpose
Function
(Purpose)
Related soft SW
The send test of dial pulse and DTMF signal is performed and the
make time adjustment of dial pulse and the DTMF signal send level
adjustment are performed if necessary.
The DTMF signal of the specified dial number is delivered until the
interruption command is provided by pressing the [BACK] key.) When
another dial number is specified during delivery of the signal, the new
dial number is delivered.
The signal send level is returned to the soft SW set value before execution of the mode after completion of the mode.
Note: Executable only when the FAX is installed.
66-21
Purpose
Function
(Purpose)
Adjustment/Setting/Check
FAX information print
Operation/procedure
Used to set the make time. By performing the test, the registered
dial pulse of max. 100 digits can be sent from the line.
When "*" and "#" are included in the registered dial number, they are
disregarded and the number is not processed as a dial.
The make time set in the dial test is written into the corresponding
soft SW.
Default: 1 2 3 4 5 6 7 8 9 0
Operate the [ ] [ ] key in DP dial selection menu to switch.
(Time before pulse delivery can be changed as 2sec 4sec
8sec.)
A
B
C
D
Print information
User switch list
Soft SW list
Dump list
System error
Protocol monitor
Details
Set the signal send level to 0dB or the soft SW set value.
Used to set the high level group and the low level group of DTMF
signal send level. By executing the test, DTMF signal is sent from
the line to a recorded dial number of max. 100 digits.
The high group/low group value of the DTMF signal send level set in
the dial test is written into the corresponding soft SW.
66-22
Default: 1 2 3 4 5 6 7 8 9 * 0 #
In the PB dial select menu, press [][] keys to select.
Pressing the [CLEAR] key during the operation clears the input
value and returns to the value input menu.
Max. 100 digits can be assigned to each dial (0 - 9, *, #). While the
default value is displayed at first, a desired value can be entered and
the entered value is stored on the FAX side until the menu is canceled.
After completion of the mode, the signal send level is returned to the
soft SW set value before execution of the mode.
Make time
Break time
DTMF signal
adjustment
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
Handset sound volume adjustment
SW13-1 to 2
Operation/procedure
By selection of the sound volume number, the sound volume of the
handset can be set or changed. The set value is written into the soft
SW.
During execution of the simulation, the reply sound message for auto
selection of TEL/FAX, "Hold the line for a while," is delivered.
Sound volume number
1
2
3
Sound volume
Small
Medium
Large
Adjustment/Setting/Check
Recognize TEL/LIU state change.
Operation/procedure
66-17
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
DTMF signal send
SW53-1 to 4 (DTMF high group end level)
SW53-5 to 8 (DTMF low group send level)
Operation/procedure
Set the signal send level to 0dB or the soft SW set value, and specify
one dial to be delivered to.
When the relay state of the polarity reverse relay, the handset hook
switch, or the external telephone hook switch is changed, the content
of change is displayed regardless of the soft SW setup. The display of
change is kept until an interruption command is supplied by pressing
the [BACK] key.
Check signal
HS2
HS1
RHS
EXHS
Notification contents
Signal low
Signal high
ON
OFF
ON
OFF
ON
OFF
ON
OFF
66-32
Adjustment/Setting/Check
Purpose
Receive data check
Function
(Purpose)
Operation/procedure
The data received from the line are checked to insure that the following
reception data are identical to the judgment data. If identical, "OK" is
notified. If not, "NG."
A judgment is made according to the reception start data. Continuous
coincidence is required.
Receive speed
Receive data
Number of judgment data
300bps
00
100
1
2
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
Communication time measurement display
Operation/procedure
The send/receive test is performed, and the time required for send/
receive of the image data in the test is measured and displayed.
Measuring
range
Send
Receive
Communication
: Memory send
means
: Normal Character
Picture quality
: Lighter
Density
: ON
ECM
: OFF
Sender information
From flag reception before sending of
image data until sending of RCP frame
From flag reception before reception of
image data until reception of RCP frame
Used to make communication not in a
simulation process but in the normal screen
and measure the time.
Enter the simulation for communication time
check and check the time.
msec
NS
NS
S
S
M
M
L
L
Sound
volume
Pattern
01 to 35
01 to 35
Call sound
Lline monitor sound
(Test sound :
Communication
signal sound)
On hook
(Test sound :
Communication
signal sound)
Read complete
sound
Communication
end sound
DTMF signal send
sound
Setting
Disable
01 to 35
NS
01 to 35
NS
01 to 35
NS
01 to 35
1
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
2
M
M
M
M
M
VR set value
3 4 5 6
L
L
L
L
M
M
M
M
L
L
L
M
M
M
L
L
M
M
L
M
S
S
S
S
M
M
M
M
Sound
7 volume 1
20
21
22
23
L
24
25
26
27
L
28
29
30
L
31
32
L
33
L
34
35
2
S
S
S
S
S
S
VR set value
3 4 5 6
M L
M
L
M
M L
M
M
S M L
S M
L
S M
S
M L
S
M
S
M
S M L
S M
S
M
S M
L
L
L
L
L
L
L
L
L
L
L
L
66-37
Purpose
Function
(Purpose)
Related soft SW
SW10-1
Sound kinds
(Test sound)
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Speaker sound volume adjustment
SW 86-1, 2 (call sound)
SW 85-1, 2 (line monitor sound)
SW 84-1, 2 (on hook)
SW 88-1, 2 (read end sound)
SW 89-1, 2 (communication end sound)
SW 87-1, 2 (DTMF send sound)
SW75-1, 2 (send end sound length)
SW75-3, 4 (receive end sound length)
Operation/procedure
The following test sound is delivered to the line and the speaker to
adjust the sound kind and volume.
The send level to the line is the set value of soft SW.
The set values of the selected sound kind and volume are written to
each soft SW.
Adjustment/Setting/Check
Time setting/check
Operation/procedure
Read/write the time (year, month, day, min., sec.) on RTC of FAX
PWB.
Note: Executable only when the FAX is installed.
66-41
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
CI signal check
SW12-6 to 7, SW55-1 to 7
Operation/procedure
The call signal from CI pin is detected to deliver the call sound to the
line and the speaker. The volume of call sound follows the soft SW.
Signal detection and delivery of pseudo-call sound at detection are
executed until the interruption command is provided by pressing the
[BACK] key.
Note: Executable only when the FAX is installed.
AR-235/275 SIMULATION - 37
66-50
Japan only
Note
Adjustment/Setting/Check
Purpose
FAST SRAM clear
Function
(Purpose)
Operation/procedure
66-53
Purpose
Function (Purpose)
Adjustment/Setting/Check
SRAM backup
Operation/procedure
Used to save the SRAM data to the expanded memory and read it.
66-51
Purpose
Function
(Purpose)
Related soft SW
When reading, however, the current FAX software version and the
header FAX software version are collated together. If they are not identical, reading cannot be performed.
Adjustment/Setting/Check
Signal detection check
1. Back-up targets
SW13-3, 4 (call sound volume)
SW32-1 to 4 (Distinctive Ring)
SW12-6, 7 (CI detection pattern)
(00:4 Sine wave 10:3 Sine wave 01:2 Sine wave)
SW26-3, 4 (speaker volume)
SW35-3, 4 (CI extinction maximum OFF time)
SW51-7, 8 (BT detection cycle)
SW52-1, 2 (BT/DT detection level)
SW55-1 to 7 (detection possible time of CI
signal)
SW56-5, 6 (DT, BT filter efficiency)
SW56-7 (DP, BT detection level)
Operation/procedure
The detection test of signals is performed and the test result is displayed.
1. Detected signal
Detected in off-hook.
Detected in off-hook.
2. Display combination
Combination
CI, CNG, FNET
CED, CNG, BusyTone, DTMF
CED, Flag, BusyTone
CED, Flag, DialTone
CED, Flag, SDT
Hook state
On hook
Off hook
2. Internal process
SRAM stack processing
1) Used to check if the installed expansion memory is ready to use.
If an expanded memory is available, write the target data of the
SRAM.
2) After completion of writing, management information is written to
the management information block.
3) For the management information, refer to the table below.
However, the FAX program version No. area is written into the data
version no. area (FFF0 - FFFF).
Lowest
address
A
B
C
D
E
Target data
0000 to
FFAF
FFB0 to
FFCF
FFD0 to
FFDF
FFE0 to
FFEF
FFF0 to
FFF1
FFF2 to
FFF3
FFF4 to
FFF7
FFF8 to
FFFB
FFFC to
FFFF
Area name
Expanded
memory
Upper 2MB
Content
Reserved
TEST pattern
ROM data
name
Data version
No.
Write
complete FLG
SRAM clear
flag
Start address
End address
SUM
TEST pattern
*Reference
REGISTRATION
ASCII 16 Byte
ASCII 16 Byte
FAX program
version No.
ERASE=H'FFFF
Completion=H'0000
Clear/No=H'0000
Clear/Yes=H'0001
Data start address
Invalid
*TEST pattern
Adjustment/Setting/Check
Pseudo-ringer check
Operation/procedure
The pseudo-ringer sound is provided in both of the main speaker
and the external telephone.
Holding the handset or the external telephone set stops the bell.
Hanging it restarts ringing. This operation is continued until the interruption command is supplied by pressing the [BACK] key.
The LCD displays the TEL/LIU status, indicating the HOOK condition.
During sending the pseudo-ringer, RBT (Ring Back Tone) is delivered to the line.
The bell is ON for 1sec and OFF for 2sec. When off-hooking with the
bell ON, the HOOK detection at pseudo-ringer ringing can be
checked. When off-hooking with the bell OFF, the HOOK detection
before pseudo-ringer ringing can be checked.
Address
FFB0
FFB2
FFB4
FFB6
FFB8
FFBA
Date
0001
0002
0004
0008
0010
0020
Address
FFBC
FFBE
FFC0
FFC2
FFC4
FFC6
Date
0040
0080
0100
0200
0400
0800
Address
FFC8
FFCA
FFCC
FFCE
Date
1000
2000
4000
8000
AR-235/275 SIMULATION - 38
COMPLETE
FAILED
(Flash Device)
(Processing state)
PROGRAM
RECEIVE
BOOTROM
ERASE
PS KANJI FONT
WRITE
ESC/P KANJI FONT
VERIFY
OPTION FONT
Press the [CA] key to cancel the simulation and reset.
Note: Executable only when the PCL is installed.
67-17
Function (Purpose)
Operation/procedure (Pattern 7)
67
67-11
Purpose
Function (Purpose)
If there is no abnormality after Clear operation, "COMPLETE" is displayed. If there is any abnormality, "ERROR" is displayed.
(Initial screen)
(Process check screen) (Executing screen)
Setting
Used to set the Select-IN signal.
Operation/procedure (Pattern 1)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Sim67-11 SELECT-IN
SELECT-IN SIGNAL 0
(0:ON 1:OFF)
[ 0- 1]
Setting range
Default
PRESS OK KEY
NOW DOING...
0-1
0
COMPLETE
PRESS OK KEY
ERROR
PRESS OK KEY
67-14
67-18
Function (Purpose)
Function (Purpose)
Operation/procedure
Operation/procedure (Pattern 7)
Download PCL.
Pressing the [OK] key displays "Please Send Data" "Ready" and the
data is sent from the PC under the MS-DOS command of FCOPY and
the file name.
Press the [OK] key again to clear. Press the [BACK] key to interrupt
clearing.
Used to overwrite and check the flash device while displaying its process status.
After completion, the result is displayed.
(It takes a little time to display READY.)
If there is no abnormality after Clear operation, "COMPLETE" is displayed. If there is any abnormality, "ERROR" is displayed.
(Initial screen)
(Process check screen) (Executing screen)
Sim67-18 APP. CLR.
APP. DATA CLEAR
PRESS OK KEY
NOW DOING...
COMPLETE
PRESS OK KEY
ERROR
PRESS OK KEY
AR-235/275 SIMULATION - 39
67-20
Function (Purpose)
Operation/procedure
The network scanner is checked.
When [OK] key is pressed, "Please Send Data" and "READY" are displayed, and then ftp is booted from MS-DOS.
Put the file name, and data are transmitted from the PC.
The process is displayed. Check the display.
After completion, the result is displayed.
(It takes a little time to display READY.)
(1)
(2)
Sim67-20 SCAN TEST
PRESS OK KEY
(3)
Sim67-20 SCAN TEST
TEST DATA
RECEIVE
COMPLETE
ERROR
(TEST DATA)
TEST DATA
(Process status)
RECEIVE
TESTING
Pressing [CA] key cancels the simulation resets the operation.
Note: Executable only when PCL and NIC are installed.
AR-235/275 SIMULATION - 40
F1
F2
F5
F6
02
10
11
12
00
01
06
08
11
15
02
04
02
00
10
80
81
82
84
88
99
Trouble
detection
Trouble contents
IMC board communication trouble
IMC board trouble
IMC ASIC error
IMC CODEC error
IMC board flash ROM error
IMC board Work RAM error
IMC board Page Memory error
IMC board image compression store
memory error
IMC board smoothing IC error
IMC PWB communication trouble
(protocol)
IMC PWB communication trouble (Parity)
IMC PWB communication trouble
(Overrun)
IMC PWB communication trouble
(Framing)
IMC PWB communication trouble (Timeout)
LSU trouble
Shading trouble (black correction)
Shading trouble (white correction)
Shading trouble
Finisher communication trouble
Finisher jogger shift trouble
Finisher shift motor abnormality
Finisher staple shift motor trouble
Pusher motor trouble
Finisher elevator motor trouble
Toner supply failure
Identification error
Model error
Type error
Destination error
Data abnormality
Misc error
Copy lamp lighting abnormality
F6-**: MCU-FAX communication trouble
FAX control PWB trouble
FAX control PWB communication trouble
(Protocol)
FAX control PWB communication trouble
(Parity)
FAX control PWB communication trouble
(Over-run)
FAX control PWB communication trouble
(Framing)
FAX control PWB communication trouble
(Timeout)
Machine-FAX board language error
Trouble
code
Main Sub
code code
F9
00
10
80
81
MCU
82
84
88
H2
H3
H4
H5
L1
L3
L4
L6
L8
U2
FIN
U7
U9
99
00
00
00
01
02
00
00
01
11
10
01
04
11
12
20
40
00
00
80
81
82
84
88
MCU
CE
99
00
01
02
03
04
05
EE
EL
EU
PF
00
Trouble contents
F9-**: MCU-PRT communication trouble
Printer PWB trouble
Printer PWB communication trouble
(Protocol)
Printer PWB communication trouble
(Parity)
Printer PWB communication trouble
(Overrun)
Printer PWB communication trouble
(Framing)
Printer PWB communication trouble
(Timeout)
Machine-PCL board language error
Thermistor open detection
Heat roller abnormally high temperature
Heat roller abnormally low temperature
5 continuous T10D(T20D) not-reaching
JAM
Fusing thermistor abnormality
Scanner feed trouble
Scanner return trouble
Main motor lock
Shifter motor trouble
Polygon motor lock trouble
Zero cross detection error
EEPROM communication error
Counter check sum error
Adjustment value check sum error
Machine speed code data error
CRUM chip communication error
RIC communication trouble
U9-**: MCU-OPE communication trouble
Operation control PWB communication
trouble (Protocol)
Operation control PWB communication
trouble (Parity)
Operation control PWB communication
trouble (Overrun)
Operation control PWB communication
trouble (Framing)
Operation control PWB communication
trouble (Time-out)
Operation panel language error
The other communication error has
occurred.
The print server card (AR-NC3D) is not
installed or defective.
The specified mail server or the FTP
server is not found.
The specified server does not
correspond during image transmission.
The entered account name of the FTP
server or the password is invalid.
The entered directory of the FTP server
is invalid.
Developer adjustment trouble (Overtoner abnormality)
Developer adjustment trouble (Undertoner abnormality)
RIC copy inhibit signal received
Trouble
detection
MCU
OPE
Network
Network
Network
Network
Network
Network
2. Self diagnostics
Trouble
code
Main Sub
code code
E1
00
Details of trouble
Content
Details
Cause
Check
and
remedy
10
Content
Details
Cause
Check
and
remedy
11
12
13
14
Trouble
code
Main Sub
code code
E1
15
Content
Details
Cause
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
Cause
Check
and
remedy
Remarks
JBIG IC abnormality
IMC board flash ROM error
Flash ROM abnormality on IMC board
IMC board abnormality
Replace the IMC PWB.
"When the program download is
abnormally terminated, a error may occur.
In this case, download the program again."
Program ROM abnormality
IMC board Work RAM error
IMC extended compression memory
module installation error
IMC extended compression memory
access error
IMC expanded memory module
installation trouble
IMC expanded memory module trouble
IMC expanded memory contact trouble
IMC board abnormality
Check installation of the expanded
memory module. (Spec: Added to Slot 1.)
Replace the expanded memory module.
Replace the IMC PWB.
Extend memory abnormality for
compressed image store (DIMM module)
16
Details of trouble
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
17
80
Cause
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Content
Details
Cause
Check
and
remedy
81
Content
Details
Cause
Check
and
remedy
82
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
E1
84
Details of trouble
Content
Details
Cause
Check
and
remedy
88
Content
Details
Cause
Check
and
remedy
E7
02
Content
Details
Cause
Check
and
remedy
10
Content
Details
Cause
11
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
E7
12
Details of trouble
Content
Details
Cause
Check
and
remedy
F1
00
Content
Details
Cause
Check
and
remedy
01
Content
Details
Cause
06
Check
and
remedy
Content
Details
Cause
08
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Shading trouble
White correction is not completed in the
specified number of times.
Flat cable installation failure to CCD unit
"Dirt on the mirror, lens, and reference
white plate"
Copy lamp lighting trouble
CCD unit abnormality
MCU PWB abnormality
"Clean the mirror, the lens, and the
reference white plate."
Check the copy lamp light quantity and its
operation. (SIM 5-3)
Check CCD unit.
Check MCU PWB.
Finisher communication trouble
Communication line test error occurs when
power is turned on or after the exit of a
simulation mode.
Error in Finisher communication
Connection trouble or disconnection of the
connector and harness between the body
and the finisher.
Finisher control PWB trouble
Control PWB failure
Malfunction by noises
Turn off/of the power to cancel the trouble.
Check connector/harness of
communication line
Replace the finisher control PWB.
Side guide plated home position error
The side guide plate cannot return to the
home position.
Side guide plate drive motor abnormality
Side guide plate home position sensor
abnormality
Use SIM3-3-1 to check the side guide
plate motor operation.
Offset motor trouble
When the offset motor of the finisher is
driven it does not reach the specified
position.
Offset motor abnormality
Offset motor origin sensor abnormality
Finisher PWB abnormality
Use SIM 3-3-6 to check the offset motor
operation.
Staple motor error
The staple motor cannot return to the
home position.
Staple motor abnormality
Staple motor home position sensor
abnormality
Staple unit abnormality
Use SIM 3-3-7 to check the staple motor
operation.
Trouble
code
Main Sub
code code
F1
11
Details of trouble
Content
Details
Cause
15
Check
and
remedy
Content
Details
Cause
F2
02
Check
and
remedy
Content
Details
Cause
04
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
F5
02
Content
Details
Cause
Check
and
remedy
Remarks
F6
00
Content
Details
Cause
Check
and
remedy
10
Identification error
Model error
Type error
Destination error
Data abnormality
Misc error
Identification error
When the CRUM trademark differs.
When the CRUM company code differs.
Model error
When the boot program model code does
not match with the CRUM model
information.
Type error
When the CRUM type is other than
[Genuine/Conversion/Production rotation].
Destination error
The destination of the body differs from
that of the CRUM.
Data abnormality
The initial check information includes an
erroneous value.
When the max. toner supply time is 00:
When the print hard stop is 00:
CRUM chip failure
Erroneous developing unit
Replace the CRUM chip.
Replace the developing unit
Details of trouble
Content
Details
Cause
Check
and
remedy
80
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
F6
81
Details of trouble
Content
Details
Cause
Check
and
remedy
82
Content
Details
Cause
Check
and
remedy
84
Content
Details
Cause
Check
and
remedy
88
Content
Details
Cause
Check
and
remedy
99
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
F9
00
Details of trouble
Content
Details
Cause
Check
and
remedy
10
Content
Details
Cause
Check
and
remedy
80
Content
Details
Cause
Check
and
remedy
81
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
F9
82
Details of trouble
Content
Details
Cause
Check
and
remedy
84
Content
Details
Cause
Check
and
remedy
88
Content
Details
Cause
Check
and
remedy
99
Content
Details
Cause
Check
and
remedy
H2
00
Content
Details
Cause
Check
and
remedy
Remarks
Trouble
code
Main Sub
code code
H3
00
Details of trouble
Content
Details
Cause
Check
and
remedy
H4
00
Content
Details
Cause
Check
and
remedy
H5
01
Content
Details
Cause
Check
and
remedy
02
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
L1
00
Details of trouble
Content
Details
Cause
Check
and
remedy
L3
00
Content
Details
Cause
Check
and
remedy
L4
01
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
L4
11
Details of trouble
Content
Details
Cause
Check
and
remedy
L6
10
Content
Details
Cause
Check
and
remedy
L8
01
Content
Details
Cause
Check
and
remedy
U2
04
11
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
Cause
12
Check
and
remedy
Remarks
Content
Details
Cause
Check
and
remedy
Remarks
Trouble
code
Main Sub
code code
20
U2
Details of trouble
Content
Details
Cause
Check
and
remedy
Remarks
40
Content
Details
Cause
Check
and
remedy
U7
00
Remarks
Content
Details
Cause
U9
00
Check
and
remedy
Content
Details
Cause
Check
and
remedy
80
Content
Details
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
81
U9
Details of trouble
Content
Details
Cause
82
Check
and
remedy
Content
Details
Cause
84
Check
and
remedy
Content
Details
Cause
88
Check
and
remedy
Content
Details
Cause
99
Check
and
remedy
Content
Details
Cause
CE
00
Check
and
remedy
Content
Detail
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
CE
01
Details of trouble
Content
Detail
Cause
Check
and
remedy
02
Content
Detail
Cause
Check
and
remedy
Trouble
code
Main Sub
code code
CE
05
Cause
Check
and
remedy
EE
EL
Cause
EU
Content
Detail
Cause
Check
and
remedy
04
Content
Detail
Cause
Check
and
remedy
Check
and
remedy
Content
Details
03
Content
Details
Content
Detail
Details of trouble
Cause
PF
00
Check
and
remedy
Content
Details
Cause
Check
and
remedy
R: Replace
L: Lubricate
Unit
Parts
Process unit Drum
Cleaning blade
Drum frame unit
Seal F/R
MC unit
50k
R
R
N
N
100k
R
R
N
N
150k
R
R
N
N
200k
R
R
R
N
250k
R
R
N
N
300k
R
R
N
N
Developer
DV seal
Side seal (F/R)
Upper heat roller
Lower heat roller
Upper separation pawl
Lower separation pawl
Thermistor
Upper heat roller gear
Upper heat roller bush
Lower heat roller bearing
Paper guide
Pickup roller (Multi bypass tray)
Separation sheet (Multi bypass tray)
Separation roller (Multi bypass tray)
Pickup roller (500 sheets tray)
Separation sheet (500 sheets tray)
Separation roller (500 sheets tray)
Transport roller unit
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
R
Y
R
Y
Y
R
R
N
Y
N
N
N
N
N
N
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
R
R
R
R
Y
R
R
R
Y
N
N
N
N
N
N
Ozone filter
Paper feed rollers
Gears
Dust-proof glass
R
Y
L
R
Y
L
R
Y
L
R
Y
L
R
Y
L
R
Y
L
Fusing unit
Paper feed
Transport
roller unit
Ozone filter
Others
LSU
2. Counter clear
Item
Maintenance cycle setting
Jam/trouble counter clear
Paper feed counter clear
DF/Scan/Stapler counter clear
Maintenance counter clear
Developing counter clear
Copy counter clear
Drum counter clear
Printer, other counter clear
FAX related counter clear
Scanner mode counter clear
SIM
SIM 21-1
SIM 24-1
SIM 24-2
SIM 24-3
SIM 24-4
SIM 24-5
SIM 24-6
SIM 24-7
SIM 24-9
SIM 24-14
SIM 24-15
Remarks
At maintenance
At maintenance
At drum replacement
At developer replacement
At drum replacement
Parts
(1) Drum
(2) Drum section a.
b.
c.
d.
e.
Main charger
Cleaning blade
Drum frame unit
Moquette F/R
Separation pawl
Note
Unit
B. Developing unit
Parts
(1) Developer
(2) DV seal/side seal
C. Fusing unit
(1) Upper heat roller
(2) Lower heat roller
(3) Fusing Separation Pawl (upper)
(4) Fusing Separation Pawl (lower)
(5) Thermistor
(6) Upper heat roller gear
(7) Upper heat roller bearing
(8) Lower heat roller bearing
(9) Paper guide
D. Paper feed
(1) Multi manual a. Paper feed roller/pickup
paper feed
roller
b. Separation sheet
(2) Upper 500
a. Paper feed roller
sheets tray
b. Pickup roller
paper feed
c. Separation sheet
(3) Lower 500
a. Paper feed roller
sheets tray
b. Pickup roller
paper feed
c. Separation sheet
E. Side door unit
(1) Transport roller unit
F. 1st paper exit unit (1) Paper exit roller
G. Laser unit
(1) LSU
Unit
H. Power unit
I. PWB
b. Cleaning blade
Parts
(1) Power source
(1) Option CN PWB
(2) IMC PWB
(3) MCU PWB
(4) Motherboard PWB
(5) Second interface PWB
Ozone filter
J.Others
1)
2)
4. Details
A. Process unit
(1) Drum
1)
2)
2
4)
3)
1
No.
Part name
1 Drum
Service items
Replace
Cycle
50k
Remarks
1)
4)
1)
d. Moquette F/R
2)
3)
Note: If it disturbs the blade movement, replace it and attach new one.
e. Separation pawl
Disassembly * Hold the tip of the separation pawl and remove it.
Assembly* Press the center of the separation pawl and install it.
No.
1
2
3
4
Part name
Cleaning
blade
Drum frame
unit
Service
items
Replace
Check
Replace
Moquette F/R Check
MC unit
Replace
Cycle
Separation
pawl unit
Check
Replace
50k
50k
200k
50k
50k
Remarks
50k
100k
positions.
Unit supply only
(Individual parts in the unit
can not be supplied.)
Unit supply only
(Individual parts in the unit
can not be supplied.)
B. Developing section
(1) Developer
2)
3
1)
No.
Part name
1 Developer
2 DV seal
3 DV side seal (F/R)
2
Service items
Replace
Check
Check
3
Cycle
50k
50k
50k
Remarks
C. Fusing section
1)
2)
4)
3)
1)
2)
2)
1)
1)
(1) Upper heat roller
1)
4)
3)
2)
2)
1)
2)
1)
1)
4
4)
2
4)
3)
2)
3)
2)
2)
(5) Thermistor
2) 3)
1)
4)
2) 3)
2)
1)
3
1)
1)
2)
1)
2)
2)
2)
1)
2)
3)
1)
3)
3)
3)
6
(7) Upper heat roller bearing
1)
2)
1)
8
A
5)
B
4)
3)
2)
3)
2)
2)
5)
3)
2)
3)
A
B
C
1)
1)
1)
4)
3)
2)
7)
6)
5)
2)
1)
No.
Part name
1 Upper heat roller
2
3
4
5
6
7
8
9
Service items
Cleaning
Replace
Lower heat roller
Cleaning
Replace
Upper separation pawl Cleaning
Replace
Lower separation pawl Cleaning
Replace
Thermistor
Cleaning
Upper heat roller gear Lubricate
Replace
Upper heat roller
Check
bearing
Replace
Lower heat roller
Check
bearing
Replace
Paper guide
Cleaning
Cycle
50k
150k
50k
300k
50k
150k
50k
300k
50k
50k
150k
50k
150k
50k
300k
50k
Remarks
7)
Removal*Raise the shutter arm before its removal.
2)
1)
2)
Installation*Install so that the boss of the lever arm comes into the rib
of the shutter arm.
3)
1)
2)
5)
1)
L O CK
4)
2)
OK
2
b. Separation sheet
1)
2)
3
3)
Installation*Install so that the cam transmit arm (1) comes under the
roller arm (2).
1)
2)
Slightly apply grease GP501MR (UKOG-0012QSZZ) around the
Part name
Service
items
Check
Cycle
50k
50k
50k
Remarks
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
2)
2)
1)
3)
4)
2)
3)
4)
1)
Note: With the toner cartridge installed, do not tilt or shake the developer cartridge.
2)
b. Separation sheet
2)
1)
1)
1)
3)
1)
Part name
Service
items
Check
Cycle
50k
50k
50k
Remarks
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
1)
3)
2)
1)
1)
2)
3)
2)
1
4)
2)
2
4)
1)
Check that two springs are securely inserted into the transfer roller
b. Separation sheet
unit bosses.
No.
1
Part name
Transport
roller unit
Service
items
Cleaning
Replace
Cycle
Remarks
50k
100k
2)
1)
2)
1)
Service
items
Check
Part name
Cycle
Remarks
50k
50k
50k
3)
2)
2)
1)
1)
3)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 10
1)
2)
1)
1)
2)
2)
1)
1)
1)
2)
3)
2)
1)
Remove the MCU PWB section connector.
1)
2)
1)
(1) LSU
Note: Check to confirm that the solenoid shaft is in the gate bracket,
and fix with the screw.
2)
1)
1)
1)
1)
1)
1)
2)
2)
1)
G. Laser unit
1)
3)
4)
2)
Note: Before removing the left cover, remove the No.1 cassette in
advance.
1)
I. PWB
(1) Option CN PWB
1)
2)
2)
2)
2)
2)
3)
1)
3)
1)
(2) IMC PWB
1)
H. Power unit
(1) Power source
2)
1)
1)
1)
2)
1)
1)
1)
1)
2)
2)
1)
1)
1)
1)
4)
2)
3)
2)
1)
1)
1)
2)
1)
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 14
1)
1
2)
1)
Note: Before removing the left cover, remove the No.1 cassette in
advance.
2)
2)
1)
1)
1)
1)
J. Ozone filter
1
2)
1)
1)
No.
Part name
1 Ozone filter
Service items
Replace
Cycle
50k
Remarks
[11] OTHERS
The download procedures of the main body program and the FAX program are as follows:
Personal computer
2) Main body side: Turn on the power of the main body. The machine
enters the download mode.
(Type of ROM)
(Targeted PWBs)
1
MCU-PWB
Panel-PWB
IMC-PWB
FAX-PWB
Finisher-PWB
Diagrammatic sketch for upgrade method
(Personal computer)
A
RS232C connector
(9pin or 25pin)
Download
data
5) PC side: The maintenance program asks you the file name. Specify the download file (*.dat).
MCU-PWB
Download file
leopXXXX.dat:
Collective download file (Main body, IMC, Panel, FAX, Finisher)
XXXXT: Whole release version
Operation
panel
IMC-PWB FAX-PWB
Finisher
(AR-235/275)
Note: If the download file version is older than the machine file version,
the following alert message is displayed during download.
In this case, press the OK button to interrupt the current download operation, and the next download is performed.
7) PC side: When the message below is displayed, download is
completed.
Completion message: DOWNLOAD COMPLETE
8) After-process: Terminate the maintenance program, and turn on
the power of the main body.
With the above procedures, download is completed.
AR-235/275 OTHERS - 1
2. User programs
User Program
Auditing Mode
Copies per Account
Reset Account
Account Number
Control
Account Limit
Description
Enables or disables the basic auditing mode, which controls
access to copier.
Displays the total number of copies made against account
numbers.
Resets all audit accounts or selectively resets individual
accounts.
Registers accounts, deletes accounts or changes an account
number.
Sets the maximum number of copies which can be made
against a registered account number.
Guards against trial and error entering of audit account
numbers.
Changes the key operator code number.
Default
Account Number
Security
Key Operator Number
Change
Exposure Adjust
Limit of Copies
Margin Default
Erase Adjust
Initial Conditions
Stream Feeding
Message Time
30sec
Rotation Copy
Sort Auto Select
Output Trays
Memory for Printer
Offset Function
Toner Save Mode
Auto Power Off
Auto Clear
Preheat Mode
Disable Stapler
Disable Center Tray
Counting
Disable PC/Modem
Disable Auto Power
Shut-off
Disable Beep at Key
Touch
Disable Backlight
Change
Total Count
AR-235/275 OTHERS - 2
Setting range
00000 (5 digits)
Level 3
999
5 steps
AB series: 5mm pitch (5 to 20mm),
Inch series: 1/4" pitch (1/4 to 1)
AB series: 5mm pitch (5 to 20mm),
Inch series: 1/4" pitch (1/4 to 1")
50%
60sec
10/30/60/90/120/240min
60sec
0/30/60/90/120/240sec
15min
0/1/2/5/10/15/30min
Normal (6sec)
1) Event driven type text message transmission by using MIB information of Printer control board.
NIC side.
Machine name
Machine code
Installation place
Event
Paper Jam
Toner Low
Toner Empty
Paper Empty
Service Required
PM Required
Message
Condition
! ! ! MISFEED HAS OCCURRED ! ! ! When paper/document jam has occurred. If a jam is detected when the power is
turned ON or reset, checking is made again.
! ! ! TONER SUPPLY IS LOW ! ! !
When toner LOW is detected for the first time. If toner LOW is detected when the
power is turned ON or reset, checking is made again.
! ! ! ADD TONER ! ! !
When toner empty is detected for the first time. If toner empty is detected when
the power is turned ON or reset, checking is made again.
! ! ! LOAD PAPER/XXX ! ! !
When paper empty is detected for the first time. If paper empty is detected when
the power is turned ON or reset, checking is made again. No information on the
number of steps of trays. Manual feed is not supported. When a tray empty is
detected, information of all the trays that are empty at that time is delivered.
! ! ! CALL FOR SERVICE ! ! !
When the machine enters the self-diagnosis mode. If detected when the power is
turned ON or reset, checking is made again.
! ! ! MAINTENANCE REQUIRED ! ! ! When the maintenance counter or the developer counter reaches the specified
count. If detected when the power is turned ON or reset, checking is made again.
When the controller sends two or more requests during a job, only
the last request is accepted.
Counter information
When schedule driven is set, the total counter, the copy counter, and
the printer counter are displayed in a mail address for general. These
information items are supplied from the controller MIB. The "total
counter" means the "effective paper counter" controlled by the MCU.
Timer information
For schedule drive message, the Printer controller controls transmission time by means, and transmits a mail.
Timer setup is made from the Web setup page.
VARNING
Explosionsfara vid felaktigt batteribyte.
Anvnd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera anvnt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien drfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
Trademark Acknowledgments
Microsoft Windows, MS-DOS, Windows NT, Windows 2000 are trademarks of Microsoft
Corporation in the U. S. A. and other countries.
Macintosh, Power Macintosh, Mac OS, LaserWriter, and AppleTalk are registered trademarks of
Apple Computer, Inc.
IBM, PC/ AT, and PowerPC are trademarks of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation.
PCL is a trademark of the Hewlett- Packard Company.
PostScript is a registered trademark of Adobe Systems Incorporated.
NetWare is a registered trademark of Novell, Inc.
All other trademarks and copyrights are the property of their respective owners.