Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
Norhisham Bin
Isnin
Turn-up Guide
2.0
Released
July 22, 2014
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
TABLE OF CONTENTS
1
PREFACE.........................................................................................4
COMPATIBILITY...............................................................................4
CONVENTIONS................................................................................4
PRE-CONFIGURATION STEPS............................................................4
4.1
EXTERNAL ALARM
CABLING................................................................................4
4.2
CONNECT
7360FX ISAM
TO THE
VIA
CRAFT TERMINAL..........................................6
RESET
5.2
5.3
CONFIGURE
5.4
5.5
5.6
CONFIGURE
5.7
CONFIGURE SYSTEM IP
5.8
5.9
5.10 CONFIGURE
UPLINK PORTS..................................................................................7
MANAGEMENT
VLAN........................................................................8
ADDRESS........................................................................8
TELNET
THE
ON UPLINK PORTS.............................................................10
SNMP
COMMUNITIES................................................................11
THE CONFIGURATION...............................................................................12
5.22 CONFIGURE
DEFAULT
SOFTWARE
FOR DIFFERENT
ONT
TYPES..................................12
6.2
6.3
CREATE PBIT
6.4
6.5
TO
TC MAPPING PROFILES.............................................................16
FOR
IPTV SERVICE..............................................16
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
6.6
6.7
6.8
6.9
THE
PON
PORTS.................................................................................24
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
WITH
DEFAULT
SETTING.....................................................25
ON
ONT)...........................................28
ON
RGW MAXIS_VOBB)........................29
SERVICE TERMINATION..................................................................30
8.1
8.2
8.3
8.4
8.5
8.6
ON
RGW..................................................................30
ON
ONT UNI.........................................................30
ON
ONT)..........................................................30
DISPLAY
9.2
SHOW
9.3
SHOW
THE STATUS OF
LT
9.4
SHOW
THE STATUS OF
NT-A
9.5
FORCED NT SWITCH-OVER
9.6
SHOW
10
THE STATUS OF
CARD,
PON, ONT
AND
AND
UNI
PORT...................................32
NT-B REDUNDANCY...........................................32
AND RESET
DHCP
GPON.....................................................32
NT-BS
SESSION AND
CTRL-STATUS...................................32
MAC
LEARNING...................................32
DOCUMENT HISTORY..................................................................33
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
Preface
This document describes the process of configuring a 7360FX ISAM (FX-8)
for use in Telekom Malaysia network.
Compatibility
This document supports the configuration of the 7360FX ISAM (FX-8) with
the following release: ISAM R4.6.01a or higher
Conventions
The following conventions are used throughout this document:
Courier New font: denotes to be entered commands, and their output.
The # prompt denotes login as root
The > prompt denotes login as normal user
Bold italics Arial font: denotes GUI actions (menu selections or buttons).
4
4.1
Pre-configuration steps
External Alarm cabling
CO Alarm
The external alarm cable is a cable with 1 DSUB-15 connector (code 3FE
60640 GA; length 10 m)
Below shows how the cable must be connected to the FX-8 subrack
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
Note: The twisted pairs are used to link the A-wire and B-wire of each
signal, for example, the blue-white twisted pair is used for Miscellaneous
Alarm 1A wire and B wire respectively.
Note: The input alarms are implemented using Normally Closed (NC) relays
(i.e. closed when no power is applied). The output alarms are indicated by a
short circuit.
Note: The following applies for the external CO alarm signals:
Maximum current drain is 100 mA
Voltage is determined by supply voltage (48 or 60 V)
The BATRET voltage of the Alarm wire is different from the BATRET
voltage of the power plant (due to the voltage drop in the feeding cables).
It is strongly advised to add extra inline 100 mA fuses in the BATRET
connections to comply in a safe way with the maximum current drain of 100
mA in the BATRET wire.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
4.2
Sign
al
Description
RI_DS
R
DCD
DTR
EG
RXD
TXD
CTS
RTS
Data-Set-Ready
Data-Carrier-Detect
Data-Terminal-Ready
Signal Ground
Receive-Data
Transmit-Data
Clear-To-Send
Request-To-Send
Pin
Type
1
2
3
4
5
6
7
8
O
O
I
Ref
O
I
O
I
Open HyperTerminal (or equivalent) and setup the serial connection with
following parameters:
Choose C to enter the TL1. The factory username and password are:
Username = isadmin
Password = i$@mad-
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
Note: The bold part needs to be replaced by the actual value found on the
node information sheet
5.6 Configure management VLAN
Assign the management VLAN to Link Aggregation Group.
configure service vpls 200 customer 1 v-vpls vlan 200 create
configure service vpls 200 description "Management vlan"
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
configure system security radius policy TMPolicy servers 1 authserver name:TMAuth1 auth-router-inst base priority 1 acc-server
name:TMAcc1
configure system security radius policy TMPolicy servers 2 authserver name:TMAuth2 auth-router-inst base priority 2 acc-server
name:TMAcc2
configure system security radius operator-policy name:TMPolicy
configure system security domain TMDomain authenticator
radius:TMPolicy sess-timeout 10
configure system security conn-profile TMRadiusConn version 1
domain-name TMDomain reject-inv-domain
configure system security conn-policy conn-profile-name
TMRadiusConn
Note: The bold part needs to be replaced by the actual value found on the
node information sheet
5.21 Plan all inserted cards
Configure cards in the system
configure equipment slot lt:1/1/[1...16] planned-type nglt-c
unlock
5.22 Configure default Software for different ONT types
Download the desired ONT software to the OLT ONT software directory as
per below:
/pub/OntSw/Download/FE54799AOCI95
Provision the software that will be used when new ONTs are connected.
For I-240G-T:
configure equipment ont sw-ctrl 1 hw-version 3FE55142* plnd-swver-conf 3FE54799AOCI95 plnd-sw-version 3FE54799AOCI95 swdwload-ver 3FE54799AOCI95
6
6.1
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
0 committed-burst-size
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
committed-burst-size 0
singletokenbucketgpon
configure qos profiles
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
6.4
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
6.7
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
6.9
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
7
7.1
7.2
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
7.4
7.5
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
7.7
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
configure bridge port 1/1/5/1/10/voip vlan-id 400 tag singletagged vlan-scope local
configure bridge port 1/1/5/1/10/voip pvid 400
configure voice ont service 1/1/5/1/10/1 conf-method ftp ftpuser-name ontftp ftp-passwd ont123 ftp-serv-ip-addr
172.16.254.10 dhcp enabled voip-mode sip1 voip-dscp 46 conffile-name sip/d/pub/TM_9043-44.xml vlan 400 admin-state unlocked
configure interface port voip:1/1/5/1/10 admin-up
For 1 POTS service
configure voice ont pots 1/1/5/1/10/2/1 admin-state unlocked
For 2 POTS service
configure voice ont pots 1/1/5/1/10/2/1 admin-state unlocked
configure voice ont pots 1/1/5/1/10/2/2 admin-state unlocked
Note: The bold part needs to be replaced by the actual value found on the
node information sheet.
Note: For the Voice on ONT service, the upstream voice traffic will
depend on the ingress-qos profile assigned to VOICE VLAN. As per
agreed, since the VOICE VLAN is assigned to allow all 8 pbits to pass
through, therefore all upstream VOICE traffic will be tied to pbit 7.
8
8.1
Service Termination
Delete Tagged Service on RGW
Delete tagged service from port 1
configure bridge port 1/1/2/2/10/1/1 no vlan-id 500
exit all
configure qos interface 1/1/2/2/10/1/1 upstream-queue 0
bandwidth-profile none
configure qos interface 1/1/2/2/10/1/1 queue 0 shaper-profile
none
exit all
Note: The bold part needs to be replaced by the actual ONT-UNI Id to be
provisioned.
8.2
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
8.4
8.5
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
9
9.1
9.2
9.3
9.4
9.5
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.
10 Document History
Versio
n
Date
Author(s)
Description/Comment
1.0
December
20th 2013
Norhisham
Isnin
Document Creation
2.0
July 22nd
2014
Simon Lee
3.0
October
13th 2014
Simon Lee
- END OF DOCUMENT -